- 22 Jul, 2012 22 commits
-
-
Sebastian Hesselbarth authored
As mach-dove is moving towards common clock framework prepare the sdhci driver to grab its clock. Signed-off-by:
Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com> Signed-off-by:
Chris Ball <cjb@laptop.org>
-
Sebastian Hesselbarth authored
The sdio controller on dove doesn't have a bit to indicate high-speed. With the quirk set it fixes accessing high-speed sdcards. Signed-off-by:
-
Kevin Hilman authored
If platform_get_resource_by_name() fails, driver probe is aborted an should return an error so the driver is not bound to the device. However, in the current error path of platform_get_resource_by_name(), probe returns zero since the return value (ret) is not properly set. With a zero return value, the driver core assumes probe was successful and will bind the driver to the device. Fix this by ensuring that probe returns an error code in this failure path. Signed-off-by:
Kevin Hilman <khilman@ti.com> Acked-by:
Venkatraman S <svenkatr@ti.com> Signed-off-by:
-
Marek Vasut authored
The write-protect GPIO is inverted on some boards. Handle such case. Signed-off-by:
Marek Vasut <marex@denx.de> Signed-off-by:
-
Wilson Callan authored
Patch to not set reserved bits in i.MX25 PROCTL register. DMA stops working if those bits get set. Signed-off-by:
Wilson Callan <wilson.callan@savantsystems.com> Acked-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
-
Aaron Lu authored
Add a call to mmc_set_signal_voltage() to set signal voltage to 3.3v in mmc_power_up so that we do not need to touch signal voltage setting in mmc/sd/sdio init functions and rescan function. For mmc/sd cards, when doing a suspend/resume cycle, consider the unsafe resume case, the card will lose its power and when powered on again, we will set signal voltage to 3.3v in mmc_power_up before its resume function gets called, which will re-init the card. And for sdio cards, when doing a suspend/resume cycle, consider the unsafe resume case, the card will either lose its power or not depending on if it wants to wakeup the host. If power is not maintained, it is the same case as mmc/sd cards. If power is maintained, mmc_power_up will not be called and the card's signal voltage will remain at the last setting. Signed-off-by:
Aaron Lu <aaron.lu@amd.com> Tested-by:
-
Aaron Lu authored
Host has different current capabilities at different voltages, we need to record these settings seperately. The defined voltages are 1.8/3.0/3.3. For other voltages, we do not touch current limit setting. Before we set the current limit for the sd card, find out the host's operating voltage first and then find out the current capabilities of the host at that voltage to set the current limit. Signed-off-by:
Philip Rakity <prakity@marvell.com> Signed-off-by:
-
Rajendra Nayak authored
In preparation for OMAP moving to the Common Clock Framework (CCF) add clk_prepare() and clk_unprepare() for the hsmmc clocks. Signed-off-by:
Rajendra Nayak <rnayak@ti.com> Acked-by:
-
Philip Rakity authored
Power needs to be removed from the card when switching to 1.8v fails. If a regulator is used to control vmmc we need to turn the regulator off and then back on otherwise power will not be removed from the card. Signed-off-by:
-
Nicolas Ferre authored
Modify clock division displaying in debugfs for matching the new CLKDIV,CLKODD user interface arrangement. Is using the has_odd_clk_div property to choose the proper format. Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by:
-
Nicolas Ferre authored
Setting host->data to NULL is incorrect sequence in STATE_SENDING_STOP state of FSM: This early setting leads to the skip of dma_unmap_sg() in atmci_dma_cleanup() which is a bug. Idea taken from dw_mmc by Seungwon Jeon. Signed-off-by:
-
Daniel Drake authored
The Marvell CaFe is now marked as having bad card detection to fix a problem during system resume. Now on the OLPC XO-1 we are facing the issue that the card is marked as logically unremovable (via MMC_UNSAFE_RESUME), which means that mmc_card_is_removable considers the card non-removable. The existing code logic decides not to poll for card presence in this case, and card detection is also disabled because of the quirk being set. This means that no SD cards are detected when inserted after boot. Refine the logic to enable card presence polling in the case when a card is logically unremovable, only avoiding the poll in the case when the card is physically non-removable (denoted with MMC_CAP_NONREMOVABLE). Signed-off-by:
Daniel Drake <dsd@laptop.org> Signed-off-by:
-
Aaron Lu authored
Add a new flag of SDHCI_USING_RETUNING_TIMER to represent if the host is using a retuning timer for the card inserted. This flag is set when the host does tuning the first time for the card and the host's retuning mode is 1. This flag is used afterwards whenever needs to decide if the host is currently using a retuning timer. This flag is cleared when the card is removed in sdhci_reinit. The set/clear of the flag and the start/stop of the retuning timer is associated with the card's init/remove time, so there is no need to touch it when the host is to be removed as at that time the card should have already been removed. Signed-off-by:
Girish K S <girish.shivananjappa@linaro.org> Reviewed-by:
-
Liu Chuansheng authored
When debugging one bad issue, got lots of pr_warning messages "queuing unknown CIS tuple" which caused a printk storm and flooded the console. This patch changes the pr_warning to use pr_warn_ratelimited. Signed-off-by:
Liu Chuansheng <chuansheng.liu@intel.com> Signed-off-by:
-
Aaron Lu authored
In mmc_read_switch, just do a one time mode 0 switch command to get the support bits information, no need to do multiple times as the support bits do not change with different arguments. And no need to check current limit support bits, as these bits are fixed according to the signal voltage. If the signal voltage is 1.8V, the support bits would be 0xf and if the signal voltage is 3.3V, the support bits would be 0x01. We will check host's ability to set the current limit. Signed-off-by:
-
Aaron Lu authored
Some of the host settings are affected by different cards inserted, e.g. when an UHS-I card is inserted, the SDHCI_NEEDS_RETUING flag might be set when the tuning timer expired and host's max_blk_count will be reduced to make sure the data transfer for a command does not exceed 4MiB to meet the retuning mode 1's requirement. When the card is removed, we should restore the original setting of the host since we can't be sure the next card being inserted will still be an UHS-I card that needs tuning. The original setting include its max_blk_count and no set of the flag of SDHCI_NEEDS_RETUNING. Signed-off-by:
-
Aaron Lu authored
For SD hosts using retuning mode 1, when retuning timer expired, it will need to do retuning in sdhci_request before processing the actual request. But the retuning command is fixed: cmd19 for SD card and cmd21 for eMMC card, so we can't use the original request's command to do the tuning. And since the tuning command depends on the card type attached to the host, we will need to know the card type to use the correct tuning command. Signed-off-by:
-
Daniel Drake authored
At http://dev.laptop.org/ticket/11980 we have determined that the Marvell CaFe SDHCI controller reports bad card presence during resume. It reports that no card is present even when it is. This is a regression -- resume worked back around 2.6.37. Around 400ms after resuming, a "card inserted" interrupt is generated, at which point it starts reporting presence. Work around this hardware oddity by setting the SDHCI_QUIRK_BROKEN_CARD_DETECTION flag. Thanks to Chris Ball for helping with diagnosis. Signed-off-by:
-
Mark Brown authored
For most error conditions sdhci_add_host() will print a diagnostic message indicating why it failed but there are a few cases where this does not happen. Add error messages in these cases to aid diagnosis. Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by:
-
Sylwester Nawrocki authored
The s3c2410_gpio* calls are obsolete and have been scheduled for removal since several kernel releases. Remove them and use common gpiolib API. This patch is a prerequisite for removal of the S3C24XX SoC specific arch/arm/plat-samsung/include/gpio-fns.h header. Tested on Micro2440-SDK. Signed-off-by:
Sylwester Nawrocki <sylvester.nawrocki@gmail.com> Signed-off-by:
-
Philip Rakity authored
Currently only the capability_0 register can be set if SDHCI_QUIRK_MISSING_CAPS is defined. This is a problem when the capability_1 register also needs changing. Use the quirk SDHCI_QUIRK_MISSING_CAPS to allow both registers to be set. Redefining caps[1] is useful when the board design does not support 1.8v vccq so UHS modes are not available. The code that calls sdhci_add_host can then detect this condition and adjust the caps so the UHS mode will not be attempted on UHS cards. Signed-off-by:
-
Shawn Guo authored
If bootloader or platform initialization code does not enable the power supply to mmc slot, we need to do it in mmc driver. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
- 21 Jul, 2012 18 commits
-
-
Alan Cox authored
The effect of the existing code is that we continue blindly when we should warn about an invalid allocation unit. Reported-by: dcb314@hotmail.com Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44061Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
-
Philip Rakity authored
If we are using a regulator the SD Host Controller and the regulator should agree about the voltages supported. Use the common subset that is supported. Signed-off-by:
-
Philip Rakity authored
max_current_caps can return 0 if not available from the sd controller. If no regulator is present or the regulator specifies a current less then 200ma, we no longer still set the 200mA caps bit anyway. Signed-off-by:
Aaron Lu <aaron_lu@amd.com> Signed-off-by:
-
Philip Rakity authored
The sd host controller spec indicates the the MAX_CURRENT value may be returned as 0. In this case other methods need to be used to return the current. If 0 is returned and there is a regulator, ask the regulator for how much current is available. Signed-off-by:
Mark F. Brown <mark.brown314@gmail.com> Reviewed-by:
-
Guennadi Liakhovetski authored
Extend the sh_mmcif driver to support GPIO card detection, provided by the slot function module. The original .get_cd() platform callback is also preserved for now. Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Guennadi Liakhovetski authored
Currently mmc host drivers have to decide whether to enable card detection before calling mmc_add_host() -- in which case a card insertion event can arrive before the host has been completely initialised -- or after mmc_add_host(), in which case the initial card detection can be problematic. This patch adds an explicit indication of when card detection should not be carried out. With it in place enabling card detection before calling mmc_add_host() should be safe. Similarly, disabling it again after calling mmc_remove_host() will avoid any races. Signed-off-by:
-
Guennadi Liakhovetski authored
Add primitive OF support to the sh-mmcif driver, which also makes it necessary to be able to run without platform data. Signed-off-by:
-
Guennadi Liakhovetski authored
Add primitive support for OF to the SDHI TMIO glue, which also makes it necessary to be able to run without platform data. Signed-off-by:
-
Guennadi Liakhovetski authored
The tmio-mmc driver is already using the generic GPIO CD handler in IRQ mode. This patch adds support for CD polling mode and also checks for availability of a WP GPIO. Signed-off-by:
-
Guennadi Liakhovetski authored
Let SDHI platforms specify mmc_host::caps2 flags in their platform data. Signed-off-by:
-
Guennadi Liakhovetski authored
Allow tmio mmc glue drivers to pass mmc_host::caps2 flags down to the mmc layer. Signed-off-by:
-
Guennadi Liakhovetski authored
Card Write-Protect pin is often implemented, using a GPIO, which makes it simple to provide a generic handler for it. Signed-off-by:
-
Guennadi Liakhovetski authored
This prepares for the addition of further slot functions. Signed-off-by:
-
Guennadi Liakhovetski authored
A simple extension of mmc slot functions add support for CD GPIO polling for cases where the GPIO cannot produce interrupts, or where this is not desired for some reason. Signed-off-by:
-
Guennadi Liakhovetski authored
To handle CD and WP SD/MMC slot pins we need generic flags to specify their polarity. Signed-off-by:
-
Guennadi Liakhovetski authored
struct mmc_host::hotplug is becoming a generic hook for slot functions. Rename it accordingly. Signed-off-by:
-
Guennadi Liakhovetski authored
Add regulator support to the sh_mmcif driver, but also preserve the current power-callback. Also note, that the card power is not switched off during clock gating periods, hence there's no need to power it on every time the card is re-activated. Signed-off-by:
Simon Horman <horms@verge.net.au> Signed-off-by:
-
Guennadi Liakhovetski authored
From the original version of sh_mmcif the .set_pwr() callback has only been used to turn the card's power on, and the .down_pwr() callback has been used to turn it off. .set_pwr() can be used for both these tasks, which is also how it is implemented by the only user of this API: the SH7724 ecovec board. Signed-off-by:
-
