Qualcomm Bluetooth controllers may not have been provisioned with a
valid device address and instead end up using the default address
00:00:00:00:5a:ad.

This was previously believed to be due to lack of persistent storage for
the address but it may also be due to integrators opting to not use the
on-chip OTP memory and instead store the address elsewhere (e.g. in
storage managed by secure world firmware).

According to Qualcomm, at least WCN6750, WCN6855 and WCN7850 have
on-chip OTP storage for the address.

As the device type alone cannot be used to determine when the address is
valid, instead read back the address during setup() and only set the
HCI_QUIRK_USE_BDADDR_PROPERTY flag when needed.

This specifically makes sure that controllers that have been provisioned
with an address do not start as unconfigured.
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Link: https://lore.kernel.org/r/124a7d54-5a18-4be7-9a76-a12017f6cce5@quicinc.com/
Fixes: 5971752d ("Bluetooth: hci_qca: Set HCI_QUIRK_USE_BDADDR_PROPERTY for wcn3990")
Fixes: e668eb1e ("Bluetooth: hci_core: Don't stop BT if the BD address missing in dts")
Fixes: 6945795b ("Bluetooth: fix use-bdaddr-property quirk")
Cc: stable@vger.kernel.org	# 6.5
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The code shall always check if HCI_QUIRK_BROKEN_READ_ENC_KEY_SIZE has
been set before attempting to use HCI_OP_READ_ENC_KEY_SIZE.

Fixes: c569242c ("Bluetooth: hci_event: set the conn encrypted before conn establishes")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

btusb_coredump_qca() uses __hci_cmd_sync() to send a vendor-specific
command to trigger firmware coredump, but the command does not
have any event as its sync response, so it is not suitable to use
__hci_cmd_sync(), fixed by using __hci_cmd_send().

Fixes: 20981ce2 ("Bluetooth: btusb: Add WCN6855 devcoredump support")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add the support ID(0x0bda, 0x4853) to usb_device_id table for
Realtek RTL8852BE.

Without this change the device utilizes an obsolete version of
the firmware that is encoded in it rather than the updated Realtek
firmware and config files from the firmware directory. The latter
files implement many new features.

The device table is as follows:

T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=03 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=4853 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms

Cc: stable@vger.kernel.org
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The extended advertising reports do report the PHYs so this store then
in hci_conn so it can be later used in hci_le_ext_create_conn_sync to
narrow the PHYs to be scanned since the controller will also perform a
scan having a smaller set of PHYs shall reduce the time it takes to
find and connect peers.

Fixes: 288c9022 ("Bluetooth: Enable all supported LE PHY by default")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

After an innocuous optimization change in LLVM main (19.0.0), x86_64
allmodconfig (which enables CONFIG_KCSAN / -fsanitize=thread) fails to
build due to the checks in check_copy_size():

  In file included from net/bluetooth/sco.c:27:
  In file included from include/linux/module.h:13:
  In file included from include/linux/stat.h:19:
  In file included from include/linux/time.h:60:
  In file included from include/linux/time32.h:13:
  In file included from include/linux/timex.h:67:
  In file included from arch/x86/include/asm/timex.h:6:
  In file included from arch/x86/include/asm/tsc.h:10:
  In file included from arch/x86/include/asm/msr.h:15:
  In file included from include/linux/percpu.h:7:
  In file included from include/linux/smp.h:118:
  include/linux/thread_info.h:244:4: error: call to '__bad_copy_from'
  declared with 'error' attribute: copy source size is too small
    244 |                         __bad_copy_from();
        |                         ^

The same exact error occurs in l2cap_sock.c. The copy_to_user()
statements that are failing come from l2cap_sock_getsockopt_old() and
sco_sock_getsockopt_old(). This does not occur with GCC with or without
KCSAN or Clang without KCSAN enabled.

len is defined as an 'int' because it is assigned from
'__user int *optlen'. However, it is clamped against the result of
sizeof(), which has a type of 'size_t' ('unsigned long' for 64-bit
platforms). This is done with min_t() because min() requires compatible
types, which results in both len and the result of sizeof() being casted
to 'unsigned int', meaning len changes signs and the result of sizeof()
is truncated. From there, len is passed to copy_to_user(), which has a
third parameter type of 'unsigned long', so it is widened and changes
signs again. This excessive casting in combination with the KCSAN
instrumentation causes LLVM to fail to eliminate the __bad_copy_from()
call, failing the build.

The official recommendation from LLVM developers is to consistently use
long types for all size variables to avoid the unnecessary casting in
the first place. Change the type of len to size_t in both
l2cap_sock_getsockopt_old() and sco_sock_getsockopt_old(). This clears
up the error while allowing min_t() to be replaced with min(), resulting
in simpler code with no casts and fewer implicit conversions. While len
is a different type than optlen now, it should result in no functional
change because the result of sizeof() will clamp all values of optlen in
the same manner as before.

Cc: stable@vger.kernel.org
Closes: https://github.com/ClangBuiltLinux/linux/issues/2007
Link: https://github.com/llvm/llvm-project/issues/85647Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Only blink if the link is up on a LED which is programmed to also
indicate link-status.

Otherwise, if both LEDs are in use to indicate different speeds, the
resulting blinking being inverted on LEDs which aren't switched on at
a specific speed is quite counter-intuitive.

Also make sure that state left behind by reset or the bootloader is
recognized correctly including the half-duplex and full-duplex bits as
well as the (unsupported by Linux netdev trigger semantics) link-down
bit.

Fixes: c66937b0 ("net: phy: mediatek-ge-soc: support PHY LEDs")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since call_rcu, which is called in the hlist_for_each_entry_rcu traversal
of gtp_dellink, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.

To prevent this, it should be changed to hlist_for_each_entry_safe.

Fixes: 94dc550a ("gtp: fix an use-after-free in ipv4_pdp_find()")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since call_rcu, which is called in the hlist_for_each_entry_rcu traversal
of tcp_ao_connect_init, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.

To prevent this, it should be changed to hlist_for_each_entry_safe.

Fixes: 7c2ffaf2 ("net/tcp: Calculate TCP-AO traffic keys")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/ZiYu9NJ/ClR8uSkH@v4bel-B760M-AORUS-ELITE-AXSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Some usb drivers try to set small skb->truesize and break
core networking stacks.

In this patch, I removed one of the skb->truesize overide.

I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c6117 ("net: cdc_ncm: reduce skb truesize
in rx path")

Fixes: f8ebb3ac ("net: usb: ax88179_178a: Fix packet receiving")
Reported-by: shironeko <shironeko@tesaguri.club>
Closes: https://lore.kernel.org/netdev/c110f41a0d2776b525930f213ca9715c@tesaguri.club/Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jose Alonso <joalonsof@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240421193828.1966195-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

syzbot was able to trigger a NULL deref in fib_validate_source()
in an old tree [1].

It appears the bug exists in latest trees.

All calls to __in_dev_get_rcu() must be checked for a NULL result.

[1]
general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 2 PID: 3257 Comm: syz-executor.3 Not tainted 5.10.0-syzkaller #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
 RIP: 0010:fib_validate_source+0xbf/0x15a0 net/ipv4/fib_frontend.c:425
Code: 18 f2 f2 f2 f2 42 c7 44 20 23 f3 f3 f3 f3 48 89 44 24 78 42 c6 44 20 27 f3 e8 5d 88 48 fc 4c 89 e8 48 c1 e8 03 48 89 44 24 18 <42> 80 3c 20 00 74 08 4c 89 ef e8 d2 15 98 fc 48 89 5c 24 10 41 bf
RSP: 0018:ffffc900015fee40 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff88800f7a4000 RCX: ffff88800f4f90c0
RDX: 0000000000000000 RSI: 0000000004001eac RDI: ffff8880160c64c0
RBP: ffffc900015ff060 R08: 0000000000000000 R09: ffff88800f7a4000
R10: 0000000000000002 R11: ffff88800f4f90c0 R12: dffffc0000000000
R13: 0000000000000000 R14: 0000000000000000 R15: ffff88800f7a4000
FS:  00007f938acfe6c0(0000) GS:ffff888058c00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f938acddd58 CR3: 000000001248e000 CR4: 0000000000352ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
  ip_route_use_hint+0x410/0x9b0 net/ipv4/route.c:2231
  ip_rcv_finish_core+0x2c4/0x1a30 net/ipv4/ip_input.c:327
  ip_list_rcv_finish net/ipv4/ip_input.c:612 [inline]
  ip_sublist_rcv+0x3ed/0xe50 net/ipv4/ip_input.c:638
  ip_list_rcv+0x422/0x470 net/ipv4/ip_input.c:673
  __netif_receive_skb_list_ptype net/core/dev.c:5572 [inline]
  __netif_receive_skb_list_core+0x6b1/0x890 net/core/dev.c:5620
  __netif_receive_skb_list net/core/dev.c:5672 [inline]
  netif_receive_skb_list_internal+0x9f9/0xdc0 net/core/dev.c:5764
  netif_receive_skb_list+0x55/0x3e0 net/core/dev.c:5816
  xdp_recv_frames net/bpf/test_run.c:257 [inline]
  xdp_test_run_batch net/bpf/test_run.c:335 [inline]
  bpf_test_run_xdp_live+0x1818/0x1d00 net/bpf/test_run.c:363
  bpf_prog_test_run_xdp+0x81f/0x1170 net/bpf/test_run.c:1376
  bpf_prog_test_run+0x349/0x3c0 kernel/bpf/syscall.c:3736
  __sys_bpf+0x45c/0x710 kernel/bpf/syscall.c:5115
  __do_sys_bpf kernel/bpf/syscall.c:5201 [inline]
  __se_sys_bpf kernel/bpf/syscall.c:5199 [inline]
  __x64_sys_bpf+0x7c/0x90 kernel/bpf/syscall.c:5199

Fixes: 02b24941 ("ipv4: use dst hint for ipv4 list receive")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20240421184326.1704930-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jonathan Heathcote reported a regression caused by blamed commit
on aarch64 architecture.

x86 happens to have irq-safe __this_cpu_add_return()
and __this_cpu_sub(), but this is not generic.

I think my confusion came from "struct sock" argument,
because these helpers are called with a locked socket.
But the memory accounting is per-proto (and per-cpu after
the blamed commit). We might cleanup these helpers later
to directly accept a "struct proto *proto" argument.

Switch to this_cpu_add_return() and this_cpu_xchg()
operations, and get rid of preempt_disable()/preempt_enable() pairs.

Fast path becomes a bit faster as a result :)

Many thanks to Jonathan Heathcote for his awesome report and
investigations.

Fixes: 3cd3399d ("net: implement per-cpu reserves for memory_allocated")
Reported-by: Jonathan Heathcote <jonathan.heathcote@bbc.co.uk>
Closes: https://lore.kernel.org/netdev/VI1PR01MB42407D7947B2EA448F1E04EFD10D2@VI1PR01MB4240.eurprd01.prod.exchangelabs.com/Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Shakeel Butt <shakeel.butt@linux.dev>
Link: https://lore.kernel.org/r/20240421175248.1692552-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

NLMSG_DONE contains an error code, it has to be extracted.
Prior to this change all dumps will end in success,
and in case of failure the result is silently truncated.

Fixes: e4b48ed4 ("tools: ynl: add a completely generic client")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://lore.kernel.org/r/20240420020827.3288615-1-kuba@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The dev_tracker is added to ax25_cb in ax25_bind(). When the
ax25 device is detaching, the dev_tracker of ax25_cb should be
deallocated in ax25_kill_by_device() instead of the dev_tracker
of ax25_dev. The log reported by ref_tracker is shown below:

[   80.884935] ref_tracker: reference already released.
[   80.885150] ref_tracker: allocated in:
[   80.885349]  ax25_dev_device_up+0x105/0x540
[   80.885730]  ax25_device_event+0xa4/0x420
[   80.885730]  notifier_call_chain+0xc9/0x1e0
[   80.885730]  __dev_notify_flags+0x138/0x280
[   80.885730]  dev_change_flags+0xd7/0x180
[   80.885730]  dev_ifsioc+0x6a9/0xa30
[   80.885730]  dev_ioctl+0x4d8/0xd90
[   80.885730]  sock_do_ioctl+0x1c2/0x2d0
[   80.885730]  sock_ioctl+0x38b/0x4f0
[   80.885730]  __se_sys_ioctl+0xad/0xf0
[   80.885730]  do_syscall_64+0xc4/0x1b0
[   80.885730]  entry_SYSCALL_64_after_hwframe+0x67/0x6f
[   80.885730] ref_tracker: freed in:
[   80.885730]  ax25_device_event+0x272/0x420
[   80.885730]  notifier_call_chain+0xc9/0x1e0
[   80.885730]  dev_close_many+0x272/0x370
[   80.885730]  unregister_netdevice_many_notify+0x3b5/0x1180
[   80.885730]  unregister_netdev+0xcf/0x120
[   80.885730]  sixpack_close+0x11f/0x1b0
[   80.885730]  tty_ldisc_kill+0xcb/0x190
[   80.885730]  tty_ldisc_hangup+0x338/0x3d0
[   80.885730]  __tty_hangup+0x504/0x740
[   80.885730]  tty_release+0x46e/0xd80
[   80.885730]  __fput+0x37f/0x770
[   80.885730]  __x64_sys_close+0x7b/0xb0
[   80.885730]  do_syscall_64+0xc4/0x1b0
[   80.885730]  entry_SYSCALL_64_after_hwframe+0x67/0x6f
[   80.893739] ------------[ cut here ]------------
[   80.894030] WARNING: CPU: 2 PID: 140 at lib/ref_tracker.c:255 ref_tracker_free+0x47b/0x6b0
[   80.894297] Modules linked in:
[   80.894929] CPU: 2 PID: 140 Comm: ax25_conn_rel_6 Not tainted 6.9.0-rc4-g8cd26fd9 #11
[   80.895190] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qem4
[   80.895514] RIP: 0010:ref_tracker_free+0x47b/0x6b0
[   80.895808] Code: 83 c5 18 4c 89 eb 48 c1 eb 03 8a 04 13 84 c0 0f 85 df 01 00 00 41 83 7d 00 00 75 4b 4c 89 ff 9
[   80.896171] RSP: 0018:ffff888009edf8c0 EFLAGS: 00000286
[   80.896339] RAX: 1ffff1100141ac00 RBX: 1ffff1100149463b RCX: dffffc0000000000
[   80.896502] RDX: 0000000000000001 RSI: 0000000000000246 RDI: ffff88800a0d6518
[   80.896925] RBP: ffff888009edf9b0 R08: ffff88806d3288d3 R09: 1ffff1100da6511a
[   80.897212] R10: dffffc0000000000 R11: ffffed100da6511b R12: ffff88800a4a31d4
[   80.897859] R13: ffff88800a4a31d8 R14: dffffc0000000000 R15: ffff88800a0d6518
[   80.898279] FS:  00007fd88b7fe700(0000) GS:ffff88806d300000(0000) knlGS:0000000000000000
[   80.899436] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   80.900181] CR2: 00007fd88c001d48 CR3: 000000000993e000 CR4: 00000000000006f0
...
[   80.935774] ref_tracker: sp%d@000000000bb9df3d has 1/1 users at
[   80.935774]      ax25_bind+0x424/0x4e0
[   80.935774]      __sys_bind+0x1d9/0x270
[   80.935774]      __x64_sys_bind+0x75/0x80
[   80.935774]      do_syscall_64+0xc4/0x1b0
[   80.935774]      entry_SYSCALL_64_after_hwframe+0x67/0x6f

Change ax25_dev->dev_tracker to the dev_tracker of ax25_cb
in order to mitigate the bug.

Fixes: feef318c ("ax25: fix UAF bugs of net_device caused by rebinding operation")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20240419020456.29826-1-duoming@zju.edu.cnSigned-off-by: Paolo Abeni <pabeni@redhat.com>

During module probe, regulator 'vin' and 'vdd-io' are used and enabled,
but the vdd-io regulator overwrites the 'vin' regulator pointer. During
remove, only the vdd-io is disabled, as the vin regulator pointer is not
available anymore. When regulator_put() is called during resource
cleanup a kernel warning is given, as the regulator is still enabled.

Store the two regulators in separate pointers and disable both the
regulators on module remove.

Fixes: 49d22c70 ("NFC: trf7970a: Add device tree option of 1.8 Volt IO voltage")
Signed-off-by: Paul Geurts <paul_geurts@live.nl>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/DB7PR09MB26847A4EBF88D9EDFEB1DA0F950E2@DB7PR09MB2684.eurprd09.prod.outlook.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Current maintainer Douglas Miller has left IBM and no replacement has
been assigned for the driver. The eHEA hardware was last used on
IBM POWER7 systems, the last of which reached end-of-support at the
end of 2020.
Signed-off-by: David Christensen <drc@linux.ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Link: https://lore.kernel.org/r/20240418195517.528577-1-drc@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

With the recent PHYLINK changes requiring supported_interfaces to be set,
MV88E6250 family switches like the 88E6020 fail to probe - cmode is
never initialized on these devices, so mv88e6250_phylink_get_caps() does
not set any supported_interfaces flags.

Instead of a cmode, on 88E6250 we have a read-only port mode value that
encodes similar information. There is no reason to bother mapping port
mode to the cmodes of other switch models; instead we introduce a
mv88e6250_setup_supported_interfaces() that is called directly from
mv88e6250_phylink_get_caps().

Fixes: de5c9bf4 ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240417103737.166651-1-matthias.schiffer@ew.tq-group.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Michael Chan says:

====================
bnxt_en: AER fixes

This patchset fixes issues in the AER recovery logic.  The first patch
refactors the code to make a shutdown function available for AER fatal
errors.  The second patch fixes the AER fatal recovery logic.  The
third patch fixes the health register logic to fix AER recovery failure
for the new P7 chips.
====================
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>

During error recovery, such as AER fatal error slot reset, we call
bnxt_try_map_fw_health_reg() to try to get access to the health
register to determine the firmware state.  Fix
bnxt_try_map_fw_health_reg() to recognize the P7 chip correctly
and set up the health register.

This fixes this type of AER slot reset failure:

bnxt_en 0000:04:00.0: AER: PCIe Bus Error: severity=Uncorrectable (Fatal), type=Inaccessible, (Unregistered Agent ID)
bnxt_en 0000:04:00.0 enp4s0f0np0: PCI I/O error detected
bnxt_en 0000:04:00.0 bnxt_re0: Handle device suspend call
bnxt_en 0000:04:00.1 enp4s0f1np1: PCI I/O error detected
bnxt_en 0000:04:00.1 bnxt_re1: Handle device suspend call
pcieport 0000:00:02.0: AER: Root Port link has been reset (0)
bnxt_en 0000:04:00.0 enp4s0f0np0: PCI Slot Reset
bnxt_en 0000:04:00.0: enabling device (0000 -> 0002)
bnxt_en 0000:04:00.0: Firmware not ready
bnxt_en 0000:04:00.1 enp4s0f1np1: PCI Slot Reset
bnxt_en 0000:04:00.1: enabling device (0000 -> 0002)
bnxt_en 0000:04:00.1: Firmware not ready
pcieport 0000:00:02.0: AER: device recovery failed

Fixes: a432a45b ("bnxt_en: Define basic P7 macros")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We do not support two simultaneous recoveries so check for reset
flag, BNXT_STATE_IN_FW_RESET, and do not proceed with AER further.
When the pci channel state is pci_channel_io_frozen, the PCIe link
can not be trusted so we disable the traffic immediately and stop
BAR access by calling bnxt_fw_fatal_close().  BAR access after
AER fatal error can cause an NMI.

Fixes: f75d9a0a ("bnxt_en: Re-write PCI BARs after PCI fatal error.")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce bnxt_fw_fatal_close() API which can be used
to stop data path and disable device when firmware
is in fatal state.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

br_info_notify is a void function. There is no need to return.

Fixes: b6d0425b ("bridge: cfm: Netlink Notifications.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define my kernel.org address to be the canonical one, and add mailmap
entries for the various addresses (including typos) that have been
used over the years.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

First problem is a double call to __in_dev_get_rcu(), because
the second one could return NULL.

if (__in_dev_get_rcu(dev) && __in_dev_get_rcu(dev)->ifa_list)

Second problem is a read from dev->ip6_ptr with no NULL check:

if (!list_empty(&rcu_dereference(dev->ip6_ptr)->addr_list))

Use the correct RCU API to fix these.

v2: add missing include <net/addrconf.h>

Fixes: d329ea5b ("icmp: add response to RFC 8335 PROBE messages")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the following Telit FN920C04 compositions:

0x10a0: rmnet + tty (AT/NMEA) + tty (AT) + tty (diag)
T:  Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=10a0 Rev=05.15
S:  Manufacturer=Telit Cinterion
S:  Product=FN920
S:  SerialNumber=92c4c4d8
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

0x10a4: rmnet + tty (AT) + tty (AT) + tty (diag)
T:  Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#=  8 Spd=480  MxCh= 0
D:  Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=10a4 Rev=05.15
S:  Manufacturer=Telit Cinterion
S:  Product=FN920
S:  SerialNumber=92c4c4d8
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

0x10a9: rmnet + tty (AT) + tty (diag) + DPL (data packet logging) + adb
T:  Bus=03 Lev=01 Prnt=03 Port=06 Cnt=01 Dev#=  9 Spd=480  MxCh= 0
D:  Ver= 2.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=10a9 Rev=05.15
S:  Manufacturer=Telit Cinterion
S:  Product=FN920
S:  SerialNumber=92c4c4d8
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=50 Driver=qmi_wwan
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none)
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Petr Machata says:

====================
mlxsw: Fixes

This patchset fixes the following issues:

- During driver de-initialization the driver unregisters the EMAD
  response trap by setting its action to DISCARD. However the manual
  only permits TRAP and FORWARD, and future firmware versions will
  enforce this.

  In patch #1, suppress the error message by aligning the driver to the
  manual and use a FORWARD (NOP) action when unregistering the trap.

- The driver queries the Management Capabilities Mask (MCAM) register
  during initialization to understand if certain features are supported.

  However, not all firmware versions support this register, leading to
  the driver failing to load.

  Patches #2 and #3 fix this issue by treating an error in the register
  query as an indication that the feature is not supported.

v2:
- Patch #2:
    - Make mlxsw_env_max_module_eeprom_len_query() void
====================

Link: https://lore.kernel.org/r/cover.1713446092.git.petrm@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The driver queries the Management Capabilities Mask (MCAM) register
during initialization to understand if a new and deeper reset flow is
supported.

However, not all firmware versions support this register, leading to the
driver failing to load.

Fix by treating an error in the register query as an indication that the
feature is not supported.

Fixes: f257c73e ("mlxsw: pci: Add support for new reset flow")
Reported-by: Tim 'mithro' Ansell <me@mith.ro>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/ee968c49d53bac96a4c66d1b09ebbd097d81aca5.1713446092.git.petrm@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The driver queries the Management Capabilities Mask (MCAM) register
during initialization to understand if it can read up to 128 bytes from
transceiver modules.

However, not all firmware versions support this register, leading to the
driver failing to load.

Fix by treating an error in the register query as an indication that the
feature is not supported.

Fixes: 1f4aea1f ("mlxsw: core_env: Read transceiver module EEPROM in 128 bytes chunks")
Reported-by: Tim 'mithro' Ansell <me@mith.ro>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/0afa8b2e8bac178f5f88211344429176dcc72281.1713446092.git.petrm@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The device's manual (PRM - Programmer's Reference Manual) classifies the
trap that is used to deliver EMAD responses as an "event trap". Among
other things, it means that the only actions that can be associated with
the trap are TRAP and FORWARD (NOP).

Currently, during driver de-initialization the driver unregisters the
trap by setting its action to DISCARD, which violates the above
guideline. Future firmware versions will prevent such misuses by
returning an error. This does not prevent the driver from working, but
an error will be printed to the kernel log during module removal /
devlink reload:

mlxsw_spectrum 0000:03:00.0: Reg cmd access status failed (status=7(bad parameter))
mlxsw_spectrum 0000:03:00.0: Reg cmd access failed (reg_id=7003(hpkt),type=write)

Suppress the error message by aligning the driver to the manual and use
a FORWARD (NOP) action when unregistering the trap.

Fixes: 4ec14b76 ("mlxsw: Add interface to access registers and process events")
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/753a89e14008fde08cb4a2c1e5f537b81d8eb2d6.1713446092.git.petrm@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When bringing down the TX rings we flush the rings but forget to
reclaimed the flushed packets. This leads to a memory leak since we
do not free the dma mapped buffers. This also leads to tx control
block corruption when bringing down the interface for power
management.

Fixes: 490cb412 ("net: bcmasp: Add support for ASP2.0 Ethernet controller")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240418180541.2271719-1-justin.chen@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If "udp_cmsg_send()" returned 0 (i.e. only UDP cmsg),
"connected" should not be set to 0. Otherwise it stops
the connected socket from using the cached route.

Fixes: 2e8de857 ("udp: add gso segment cmsg")
Signed-off-by: Yick Xie <yick.xie@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20240418170610.867084-1-yick.xie@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The VXLAN driver currently does not check if the inner layer2
source-address is valid.

In case source-address snooping/learning is enabled, a entry in the FDB
for the invalid address is created with the layer3 address of the tunnel
endpoint.

If the frame happens to have a non-unicast address set, all this
non-unicast traffic is subsequently not flooded to the tunnel network
but sent to the learnt host in the FDB. To make matters worse, this FDB
entry does not expire.

Apply the same filtering for packets as it is done for bridges. This not
only drops these invalid packets but avoids them from being learnt into
the FDB.

Fixes: d342894c ("vxlan: virtual extensible lan")
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

driver needs queue msix vectors and one misc irq vector,
but only queue vectors need irq affinity.
when num_online_cpus is less than chip max msix vectors,
driver will acquire (num_online_cpus + 1) vecotrs, and
call pci_alloc_irq_vectors_affinity functions with affinity
params without setting pre_vectors or post_vectors, it will
cause return error code -ENOSPC.
Misc irq vector is vector 0, driver need to set affinity params
.pre_vectors = 1.

Fixes: 3f703186 ("net: libwx: Add irq flow functions")
Signed-off-by: Duanqiang Wen <duanqiangwen@net-swift.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from Jakub Kicinski:
 "A little calmer than usual, probably just the timing of sub-tree PRs.

  Including fixes from netfilter.

  Current release - regressions:

   - inet: bring NLM_DONE out to a separate recv() again, fix user space
     which assumes multiple recv()s will happen and gets blocked forever

   - drv: mlx5:
       - restore mistakenly dropped parts in register devlink flow
       - use channel mdev reference instead of global mdev instance for
         coalescing
       - acquire RTNL lock before RQs/SQs activation/deactivation

  Previous releases - regressions:

   - net: change maximum number of UDP segments to 128, fix virtio
     compatibility with Windows peers

   - usb: ax88179_178a: avoid writing the mac address before first
     reading

  Previous releases - always broken:

   - sched: fix mirred deadlock on device recursion

   - netfilter:
       - br_netfilter: skip conntrack input hook for promisc packets
       - fixes removal of duplicate elements in the pipapo set backend
       - various fixes for abort paths and error handling

   - af_unix: don't peek OOB data without MSG_OOB

   - drv: flower: fix fragment flags handling in multiple drivers

   - drv: ravb: fix jumbo frames and packet stats accounting

  Misc:

   - kselftest_harness: fix Clang warning about zero-length format

   - tun: limit printing rate when illegal packet received by tun dev"

* tag 'net-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (46 commits)
  net: ethernet: ti: am65-cpsw-nuss: cleanup DMA Channels before using them
  net: usb: ax88179_178a: avoid writing the mac address before first reading
  net: ravb: Fix RX byte accounting for jumbo packets
  net: ravb: Fix GbEth jumbo packet RX checksum handling
  net: ravb: Allow RX loop to move past DMA mapping errors
  net: ravb: Count packets instead of descriptors in R-Car RX path
  net: ethernet: mtk_eth_soc: fix WED + wifi reset
  net:usb:qmi_wwan: support Rolling modules
  selftests: kselftest_harness: fix Clang warning about zero-length format
  net/sched: Fix mirred deadlock on device recursion
  netfilter: nf_tables: fix memleak in map from abort path
  netfilter: nf_tables: restore set elements when delete set fails
  netfilter: nf_tables: missing iterator type in lookup walk
  s390/ism: Properly fix receive message buffer allocation
  net: dsa: mt7530: fix port mirroring for MT7988 SoC switch
  net: dsa: mt7530: fix mirroring frames received on local port
  tun: limit printing rate when illegal packet received by tun dev
  ice: Fix checking for unsupported keys on non-tunnel device
  ice: tc: allow zero flags in parsing tc flower
  ice: tc: check src_vsi in case of traffic from VF
  ...

Pull gpio fixes from Bartosz Golaszewski:

 - use -ENOTSUPP consistently in Intel GPIO drivers

 - don't include dt-bindings headers in gpio-swnode code

 - add missing of device table to gpio-lpc32xx and fix autoloading

* tag 'gpio-fixes-for-v6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpiolib: swnode: Remove wrong header inclusion
  gpio: lpc32xx: fix module autoloading
  gpio: crystalcove: Use -ENOTSUPP consistently
  gpio: wcove: Use -ENOTSUPP consistently

The TX and RX DMA Channels used by the driver to exchange data with CPSW
are not guaranteed to be in a clean state during driver initialization.
The Bootloader could have used the same DMA Channels without cleaning them
up in the event of failure. Thus, reset and disable the DMA Channels to
ensure that they are in a clean state before using them.

Fixes: 93a76530 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Reported-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240417095425.2253876-1-s-vadapalli@ti.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

After the commit d2689b6a ("net: usb: ax88179_178a: avoid two
consecutive device resets"), reset operation, in which the default mac
address from the device is read, is not executed from bind operation and
the random address, that is pregenerated just in case, is direclty written
the first time in the device, so the default one from the device is not
even read. This writing is not dangerous because is volatile and the
default mac address is not missed.

In order to avoid this and keep the simplification to have only one
reset and reduce the delays, restore the reset from bind operation and
remove the reset that is commanded from open operation. The behavior is
the same but everything is ready for usbnet_probe.

Tested with ASIX AX88179 USB Gigabit Ethernet devices.
Restore the old behavior for the rest of possible devices because I don't
have the hardware to test.

cc: stable@vger.kernel.org # 6.6+
Fixes: d2689b6a ("net: usb: ax88179_178a: avoid two consecutive device resets")
Reported-by: Jarkko Palviainen <jarkko.palviainen@gmail.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20240417085524.219532-1-jtornosm@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull random number generator fixes from Jason Donenfeld:

 - The input subsystem contributes entropy in some places where a
   spinlock is held, but the entropy accounting code only handled
   callers being in an interrupt or non-atomic process context, but not
   atomic process context. We fix this by removing an optimization and
   just calling queue_work() unconditionally.

 - Greg accidently sent up a patch not intended for his tree and that
   had been nack'd, so that's now reverted.

* tag 'random-6.9-rc5-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
  Revert "vmgenid: emit uevent when VMGENID updates"
  random: handle creditable entropy from atomic process context

Merge tag 'platform-drivers-x86-v6.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform driver fixes from Ilpo Järvinen:

 - amd/pmf: Add SPS notifications quirk (+ quirk support)

 - amd/pmf: Lower Smart PC check message severity

 - x86/ISST: New HW support

 - x86/intel-uncore-freq: Bump minor version to avoid "unsupported" message

 - amd/pmc: New BIOS version still needs Spurious IRQ1 quirk

* tag 'platform-drivers-x86-v6.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
  platform/x86/amd/pmc: Extend Framework 13 quirk to more BIOSes
  platform/x86/intel-uncore-freq: Increase minor number support
  platform/x86: ISST: Add Granite Rapids-D to HPM CPU list
  platform/x86/amd: pmf: Add quirk for ROG Zephyrus G14
  platform/x86/amd: pmf: Add infrastructure for quirking supported funcs
  platform/x86/amd: pmf: Decrease error message to debug

This reverts commit ad6bcdad. I had
nak'd it, and Greg said on the thread that it links that he wasn't going
to take it either, especially since it's not his code or his tree, but
then, seemingly accidentally, it got pushed up some months later, in
what looks like a mistake, with no further discussion in the linked
thread. So revert it, since it's clearly not intended.

Fixes: ad6bcdad ("vmgenid: emit uevent when VMGENID updates")
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20230531095119.11202-2-bchalios@amazon.esSigned-off-by: Jason A. Donenfeld <Jason@zx2c4.com>