Eliminate the following coccicheck warning:
./drivers/net/dsa/rtl8366rb.c:1348:2-3: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net: add a helpers for loading netdev->dev_addr from platform

Similarly to recently added device_get_ethdev_address()
and of_get_ethdev_address() create a helper for drivers
loading mac addr from platform data.

nvmem_get_mac_address() does not have driver callers
so instead of adding a helper there unexport it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the new platform_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.

  @@
  expression dev, net;
  @@
  - eth_platform_get_mac_address(dev, net->dev_addr)
  + platform_get_ethdev_address(dev, net)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

There is a handful of drivers which pass netdev->dev_addr as
the destination buffer to eth_platform_get_mac_address().
Add a helper which takes a dev pointer instead, so it can call
an appropriate helper.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

nvmem_get_mac_address() is only called from of_net.c
we don't need the export.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2021-10-07

Michal Swiatkowski says:

The following patch series introduces basic switchdev model
support in ice driver. Implement the following blocks of
switchdev framework:
- VF port representors creation
- control plane VSI definition
- exception path (a. k. a. "slow-path") - to allow a virtual
switch or linux bridge to receive any packet that doesn't match
any hw filter
- link state management of virtual ports
- query virtual port statistics

Hardware offload support in switchdev mode is out of scope of
this patchset. Devlink interface is used to toggle between
switchdev and legacy (the default) modes of the driver.

---
Note: This series includes the use enum ice_status, however, we have
patches in our queue to remove it from the driver [1]. We are working
through the patches that precede the removal series.

[1] https://patchwork.ozlabs.org/project/intel-wired-lan/list/?series=265957
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull nfsd fixes from Chuck Lever:
 "Bug fixes for NFSD error handling paths"

* tag 'nfsd-5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
  NFSD: Keep existing listeners on portlist error
  SUNRPC: fix sign error causing rpcsec_gss drops
  nfsd: Fix a warning for nfsd_file_close_inode
  nfsd4: Handle the NFSv4 READDIR 'dircount' hint being zero
  nfsd: fix error handling of register_pernet_subsys() in init_nfsd()

Pull ARM SoC fixes from Arnd Bergmann:
 "This is a larger than normal update for Arm SoC specific code, most of
  it in device trees, but also drivers and the omap and at91/sama7
  platforms:

   - There are four new entries to the MAINTAINERS file: Sven Peter and
     Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar,
     and Vignesh Raghavendra for TI K3

   - Build fixes to address randconfig warnings in sharpsl, dove, omap1,
     and qcom platforms as well as the scmi and op-tee subsystems

   - Regression fixes for missing CONFIG_FB and other options for
     several defconfigs

   - Several bug fixes for the newly added Microchip SAMA7 platform,
     mostly regarding power management

   - Missing SMP barriers to protect accesses to SCMI virtio device

   - Regression fixes for TI OMAP, including a boot-time hang on am335x.

   - Lots of bug fixes for NXP i.MX, mostly addressing incorrect
     settings in devicetree files, and one revert for broken suspend.

   - Fixes for ARM Juno/Vexpress devicetree files, addressing a couple
     of schema warnings.

   - Regression fixes for qualcomm SoC specific drivers and devicetree
     files, reverting an mdt_loader change and at least pastially
     reverting some of the 5.15 DTS changes, plus some minor bugfixes"

* tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (64 commits)
  MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer
  MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer
  firmware: arm_scmi: Add proper barriers to scmi virtio device
  firmware: arm_scmi: Simplify spinlocks in virtio transport
  ARM: dts: omap3430-sdp: Fix NAND device node
  bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
  ARM: sharpsl_param: work around -Wstringop-overread warning
  ARM: defconfig: gemini: Restore framebuffer
  ARM: dove: mark 'putc' as inline
  ARM: omap1: move omap15xx local bus handling to usb.c
  MAINTAINERS: Add Vignesh to TI K3 platform maintainership
  arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
  ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
  arm64: dts: ls1028a: fix eSDHC2 node
  arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
  ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins
  ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs
  ARM: at91: pm: preload base address of controllers in tlb
  ARM: at91: pm: group constants and addresses loading
  ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail
  ...

Apple SoC fixes for 5.15; just two MAINTAINERS updates.

- MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer
- MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer

* tag 'asahi-soc-fixes-5.15' of https://github.com/AsahiLinux/linux:
  MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer
  MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer

Link: https://lore.kernel.org/r/a50a9015-0e62-c451-4d0d-668233b35b85@marcan.stSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'scmi-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes

SCMI fixes for v5.15

A few fixes addressing:
- Kconfig dependency between VIRTIO and ARM_SCMI_PROTOCOL
- Link-time error with __exit annotation for virtio_scmi_exit
- Unnecessary nested irqsave/irqrestore spinlocks in virtio transport
- Missing SMP barriers to protect accesses to SCMI virtio device

* tag 'scmi-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  firmware: arm_scmi: Add proper barriers to scmi virtio device
  firmware: arm_scmi: Simplify spinlocks in virtio transport
  firmware: arm_scmi: Remove __exit annotation
  firmware: arm_scmi: Fix virtio transport Kconfig dependency

Link: https://lore.kernel.org/r/20211007102822.27886-1-sudeep.holla@arm.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'omap-for-v5.15/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes

Fixes for omaps for v5.15

Few regression fixes for omaps for the v5.15-rc cycle. There is a fix
for boot time hangs that can happen on some am335x devices that started
when the pruss devicetree nodes were added. The other fixes are less
critical:

- Fix compiler warning for sysc_init_soc() that got recently introduced

- Fix external abort for am335x pruss as otherwise some am335x will hang

- Use CLKDM_NOAUTO quirk also for dra7 dcan1

- Fix older NAND device node regression for omap3-sdp

* tag 'omap-for-v5.15/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap3430-sdp: Fix NAND device node
  bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
  soc: ti: omap-prm: Fix external abort for am335x pruss
  bus: ti-sysc: Add break in switch statement in sysc_init_soc()

Link: https://lore.kernel.org/r/pull-1633609552-789682@atomide.comSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Pull netfslib, cachefiles and afs fixes from David Howells:

 - Fix another couple of oopses in cachefiles tracing stemming from the
   possibility of passing in a NULL object pointer

 - Fix netfs_clear_unread() to set READ on the iov_iter so that source
   it is passed to doesn't do the wrong thing (some drivers look at the
   flag on iov_iter rather than other available information to determine
   the direction)

 - Fix afs_launder_page() to write back at the correct file position on
   the server so as not to corrupt data

* tag 'misc-fixes-20211007' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  afs: Fix afs_launder_page() to set correct start file position
  netfs: Fix READ/WRITE confusion when calling iov_iter_xarray()
  cachefiles: Fix oops with cachefiles_cull() due to NULL object

Merge tag 'perf-tools-fixes-for-v5.15-2021-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull perf tools fixes from Arnaldo Carvalho de Melo:

 - Fix plugin static linking with libopencsd on ARM and ARM64

 - Add missing -lstdc++ when linking with libopencsd

 - Add missing topdown metrics events to 'perf test attr'

 - Plug leak sys_event_tables list after processing JSON vendor events
   entries

 - Sync sound/asound.h copy with the kernel sources

* tag 'perf-tools-fixes-for-v5.15-2021-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf tests attr: Add missing topdown metrics events
  tools include UAPI: Sync sound/asound.h copy with the kernel sources
  perf build: Fix plugin static linking with libopencsd on ARM and ARM64
  perf build: Add missing -lstdc++ when linking with libopencsd
  perf jevents: Free the sys_event_tables list after processing entries

Introduce the following ethtool operations for VF's representor:
	-get_drvinfo
	-get_strings
	-get_ethtool_stats
	-get_sset_count
	-get_link

In all cases, existing operations were used with minor
changes which allow us to detect if ethtool op was called for
representor. Only VF VSI stats will be available for representor.

Implement ndo_get_stats64 for port representor. This will update
VF VSI stats and read them.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Slow path means allowing packet to go from uplink to representor
and from representor to correct VF on Rx site and from VF to
representor and to uplink on Tx site.

To accomplish this driver, has to set correct Tx descriptor. When
packet is sent from representor to VF, destination should be
set to VF VSI. When packet is sent from uplink port destination
should be uplink to bypass switch infrastructure and send packet
outside.

On Rx site driver should check source VSI field from Rx descriptor
and based on that forward packed to correct netdev. To allow
this there is a target netdevs table in control plane VSI
struct.
Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

As resetting all VFs behaves mostly like creating new VFs also
eswitch infrastructure has to be recreated. The easiest way to
do that is to rebuild eswitch after resetting VFs.

Implement helper functions to start and stop all representors
queues. This is used to disable traffic on port representors.

In rebuild path:
- NAPI has to be disabled
- eswitch environment has to be set up
- new port representors have to be created, because the old
one had pointer to not existing VFs
- new control plane VSI ring should be remapped
- NAPI hast to be enabled
- rxdid has to be set to FLEX_NIC_2, because this descriptor id
support source_vsi, which is needed on control plane VSI queues
- port representors queues have to be started
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Only way to enable switchdev is to create VFs when the eswitch
mode is set to switchdev. Check if correct mode is set and
enable switchdev in function which creating VFs.

Disable switchdev when user change number of VFs to 0. Changing
eswitch mode back to legacy when VFs are created in switchdev
mode isn't allowed.

As switchdev takes care of managing filter rules, adding new
rules on VF is blocked.

In case of resetting VF driver has to update pointer in ice_repr
struct, because after reset VSI related things can change.
Co-developed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

New type of VSI has to be defined for switchdev control plane
VSI. Number of allocated Tx and Rx queue has to be equal to
amount of VFs, because each port representor should have one
Tx and Rx queue.

Also to not increase number of used irqs too much, control plane
VSI uses only one q_vector and handle all queues in one irq.
To allow handling all queues in one irq , new function to clean
msix for eswitch was introduced. This function will schedule napi
for each representor instead of scheduling it only for one like in
normal clean irq function.

Only one additional msix has to be requested. Always try to request
it in ice_ena_msix_range function.
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Switchdev environment has to be set up when user create VFs
and eswitch mode is switchdev. Release is done when user
delete all VFs.

Data path in this implementation is based on control plane VSI.
This VSI is used to pass traffic from port representors to
corresponding VFs and vice versa. Default TX rule has to be
added to forward packet to control plane VSI. This will redirect
packets from VFs which don't match other rules to control plane
VSI.

On RX side default rule is added on uplink VSI to receive all
traffic that doesn't match other rules. When setting switchdev
environment all other rules from VFs should be removed. Packet to
VFs will be forwarded by control plane VSI.

As VF without any mac rules can't send any packet because of
antispoof mechanism, VSI antispoof should be turned off on each VFs.

To send packet from representor to correct VSI, destination VSI
field in TX descriptor will have to be filled. Allow that by
setting destination override bit in control plane VSI security config.

Packet from VFs will be received on control plane VSI. Driver
should decide to which netdev forward the packet. Decision is
made based on src_vsi field from descriptor. There is a target
netdev list in control plane VSI struct which choose netdev
based on src_vsi number.
Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

There is no way to change default lan_en and lb_en flags while
adding new rule. Add function that allows changing these flags
on ICE_SW_LKUP_DFLT recipe and any rule id.

lan_en allows packet to go outside if rule is matched. Clearing
this bit will block packet from sending it outside.

lb_en allows packet to be forwarded to other VSI. Clearing
this bit will block packet from forwarding it to other VSI.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Implement functions to make setting VSI security config easier.
Main function ice_update_security fills security section field and
checks against error in updating VSI. Reset functions are responsible
for correct filling config according to user expectations.

This helper is needed because destination override is located in
this section. Driver has to set this bit to allow strering Tx packet
on VSI based on value in Tx descriptors.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

In switchdev driver shouldn't add MAC, VLAN and promisc
filters on iavf demand but should return success to not
break normal iavf flow.

Achieve that by creating table of functions pointer with
default functions used to parse iavf command. While parse
iavf command, call correct function from table instead of
calling function direct.

When port representors are being created change functions
in table to new one that behaves correctly for switchdev
puprose (ignoring new filters).

Change back to default ops when representors are being
removed.
Co-developed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Port representor is used to manage VF from host side. To allow
it each created representor registers netdevice with random hw
address. Also devlink port is created for all representors.

Port representor name is created based on switch id or managed
by devlink core if devlink port was registered with success.

Open and stop ndo ops are implemented to allow managing the VF
link state. Link state is tracked in VF struct.

Struct ice_netdev_priv is extended by pointer to representor
field. This is needed to get correct representor from netdev
struct mostly used in ndo calls.

Implement helper functions to check if given netdev is netdev of
port representor (ice_is_port_repr_netdev) and to get representor
from netdev (ice_netdev_to_repr).

As driver mostly will create or destroy port representors on all
VFs instead of on single one, write functions to add and remove
representor for each VF.

Representor struct contains pointer to source VSI, which is VSI
configured on VF, backpointer to VF, backpointer to netdev,
q_vector pointer and metadata_dst which will be used in data path.
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Keeping devlink port inside VSI data structure causes some issues.
Since VF VSI is released during reset that means that we have to
unregister devlink port and register it again every time reset is
triggered. With the new changes in devlink API it
might cause deadlock issues. After calling
devlink_port_register/devlink_port_unregister devlink API is going to
lock rtnl_mutex. It's an issue when VF reset is triggered in netlink
operation context (like setting VF MAC address or VLAN),
because rtnl_lock is already taken by netlink. Another call of
rtnl_lock from devlink API results in dead-lock.

By moving devlink port to PF/VF we avoid creating/destroying it
during reset. Since this patch, devlink ports are created during
ice_probe, destroyed during ice_remove for PF and created during
ice_repr_add, destroyed during ice_repr_rem for VF.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Write set and get eswitch mode functions used by devlink
ops. Use new pf struct member eswitch_mode to track current
eswitch mode in driver.

Changing eswitch mode is only allowed when there are no
VFs created.

Create new file for eswitch related code.

Add config flag ICE_SWITCHDEV to allow user to choose if
switchdev support should be enabled or disabled.

Use case examples:
- show current eswitch mode ('legacy' is the default one)
[root@localhost]# devlink dev eswitch show pci/0000:03:00.1
pci/0000:03:00.1: mode legacy

- move to 'switchdev' mode
[root@localhost]# devlink dev eswitch set pci/0000:03:00.1 mode
switchdev
[root@localhost]# devlink dev eswitch show pci/0000:03:00.1
pci/0000:03:00.1: mode switchdev

- create 2 VFs
[root@localhost]# echo 2 > /sys/class/net/ens4f1/device/sriov_numvfs

- unsuccessful attempt to change eswitch mode while VFs are created
[root@localhost]# devlink dev eswitch set pci/0000:03:00.1 mode legacy
devlink answers: Operation not supported

- destroy VFs
[root@localhost]# echo 0 > /sys/class/net/ens4f1/device/sriov_numvfs

- restore 'legacy' mode
[root@localhost]# devlink dev eswitch set pci/0000:03:00.1 mode legacy
[root@localhost]# devlink dev eswitch show pci/0000:03:00.1
pci/0000:03:00.1: mode legacy
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from xfrm, bpf, netfilter, and wireless.

  Current release - regressions:

   - xfrm: fix XFRM_MSG_MAPPING ABI breakage caused by inserting a new
     value in the middle of an enum

   - unix: fix an issue in unix_shutdown causing the other end
     read/write failures

   - phy: mdio: fix memory leak

  Current release - new code bugs:

   - mlx5e: improve MQPRIO resiliency against bad configs

  Previous releases - regressions:

   - bpf: fix integer overflow leading to OOB access in map element
     pre-allocation

   - stmmac: dwmac-rk: fix ethernet on rk3399 based devices

   - netfilter: conntrack: fix boot failure with
     nf_conntrack.enable_hooks=1

   - brcmfmac: revert using ISO3166 country code and 0 rev as fallback

   - i40e: fix freeing of uninitialized misc IRQ vector

   - iavf: fix double unlock of crit_lock

  Previous releases - always broken:

   - bpf, arm: fix register clobbering in div/mod implementation

   - netfilter: nf_tables: correct issues in netlink rule change event
     notifications

   - dsa: tag_dsa: fix mask for trunked packets

   - usb: r8152: don't resubmit rx immediately to avoid soft lockup on
     device unplug

   - i40e: fix endless loop under rtnl if FW fails to correctly respond
     to capability query

   - mlx5e: fix rx checksum offload coexistence with ipsec offload

   - mlx5: force round second at 1PPS out start time and allow it only
     in supported clock modes

   - phy: pcs: xpcs: fix incorrect CL37 AN sequence, EEE disable
     sequence

  Misc:

   - xfrm: slightly rejig the new policy uAPI to make it less cryptic"

* tag 'net-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
  net: prefer socket bound to interface when not in VRF
  iavf: fix double unlock of crit_lock
  i40e: Fix freeing of uninitialized misc IRQ vector
  i40e: fix endless loop under rtnl
  dt-bindings: net: dsa: marvell: fix compatible in example
  ionic: move filter sync_needed bit set
  gve: report 64bit tx_bytes counter from gve_handle_report_stats()
  gve: fix gve_get_stats()
  rtnetlink: fix if_nlmsg_stats_size() under estimation
  gve: Properly handle errors in gve_assign_qpl
  gve: Avoid freeing NULL pointer
  gve: Correct available tx qpl check
  unix: Fix an issue in unix_shutdown causing the other end read/write failures
  net: stmmac: trigger PCS EEE to turn off on link down
  net: pcs: xpcs: fix incorrect steps on disable EEE
  netlink: annotate data races around nlk->bound
  net: pcs: xpcs: fix incorrect CL37 AN sequence
  net: sfp: Fix typo in state machine debug string
  net/sched: sch_taprio: properly cancel timer from taprio_destroy()
  net: bridge: fix under estimation in br_get_linkxstats_size()
  ...

Merge tag 'hyperv-fixes-signed-20211007' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux

Pull hyperv fixes from Wei Liu:

 - Replace uuid.h with types.h in a header (Andy Shevchenko)

 - Avoid sleeping in atomic context in PCI driver (Long Li)

 - Avoid sending IPI to self when it shouldn't (Vitaly Kuznetsov)

* tag 'hyperv-fixes-signed-20211007' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
  x86/hyperv: Avoid erroneously sending IPI to 'self'
  hyper-v: Replace uuid.h with types.h
  PCI: hv: Fix sleep while in non-sleep context when removing child devices from the bus

Hector suggested I should add myself to help him maintain the
platform.
Acked-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Sven Peter <sven@svenpeter.dev>

Add myself as a reviewer for Asahi Linux (Apple M1) patches.

I would like to be CC'ed on Asahi Linux patches for review and testing.
I am also collecting Asahi Linux patches downstream, rebasing on
linux-next periodically, and would like to be notified of what to
cherry-pick from lists.

Cc: Hector Martin <marcan@marcan.st>
Cc: Sven Peter <sven@svenpeter.dev>
Acked-by: Hector Martin <marcan@marcan.st>
Acked-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>

Use 2-factor multiplication argument form devm_kcalloc() instead
of devm_kzalloc().

Link: https://github.com/KSPP/linux/issues/162Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20211006181115.GA913499@embeddedorSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().

Link: https://github.com/KSPP/linux/issues/162Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20211006180944.GA913477@embeddedorSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().

Link: https://github.com/KSPP/linux/issues/162Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/20211006180927.GA913456@embeddedorSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use 2-factor multiplication argument form kcalloc() instead
of kzalloc().

Link: https://github.com/KSPP/linux/issues/162Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20211006180843.GA913399@embeddedorSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The commit 6da5b0f0 ("net: ensure unbound datagram socket to be
chosen when not in a VRF") modified compute_score() so that a device
match is always made, not just in the case of an l3mdev skb, then
increments the score also for unbound sockets. This ensures that
sockets bound to an l3mdev are never selected when not in a VRF.
But as unbound and bound sockets are now scored equally, this results
in the last opened socket being selected if there are matches in the
default VRF for an unbound socket and a socket bound to a dev that is
not an l3mdev. However, handling prior to this commit was to always
select the bound socket in this case. Reinstate this handling by
incrementing the score only for bound sockets. The required isolation
due to choosing between an unbound socket and a socket bound to an
l3mdev remains in place due to the device match always being made.
The same approach is taken for compute_score() for stream sockets.

Fixes: 6da5b0f0 ("net: ensure unbound datagram socket to be chosen when not in a VRF")
Fixes: e7819058 ("net: ensure unbound stream socket to be chosen when not in a VRF")
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/cf0a8523-b362-1edf-ee78-eef63cbbb428@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
pull-request: bpf 2021-10-07

We've added 7 non-merge commits during the last 8 day(s) which contain
a total of 8 files changed, 38 insertions(+), 21 deletions(-).

The main changes are:

1) Fix ARM BPF JIT to preserve caller-saved regs for DIV/MOD JIT-internal
   helper call, from Johan Almbladh.

2) Fix integer overflow in BPF stack map element size calculation when
   used with preallocation, from Tatsuhiko Yasumatsu.

3) Fix an AF_UNIX regression due to added BPF sockmap support related
   to shutdown handling, from Jiang Wang.

4) Fix a segfault in libbpf when generating light skeletons from objects
   without BTF, from Kumar Kartikeya Dwivedi.

5) Fix a libbpf memory leak in strset to free the actual struct strset
   itself, from Andrii Nakryiko.

6) Dual-license bpf_insn.h similarly as we did for libbpf and bpftool,
   with ACKs from all contributors, from Luca Boccassi.
====================

Link: https://lore.kernel.org/r/20211007135010.21143-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-drivers-next-2021-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.16

First set of patches for v5.16. ath11k getting most of new features
this time. Other drivers also have few new features, and of course the
usual set of fixes and cleanups all over.

Major changes:

rtw88

* support adaptivity for ETSI/JP DFS region

* 8821c: support RFE type4 wifi NIC

brcmfmac

* DMI nvram filename quirk for Cyberbook T116 tablet

ath9k

* load calibration data and pci init values via nvmem subsystem

ath11k

* include channel rx and tx time in survey dump statistics

* support for setting fixed Wi-Fi 6 rates from user space

* support for 80P80 and 160 MHz bandwidths

* spectral scan support for QCN9074

* support for calibration data files per radio

* support for calibration data via eeprom

* support for rx decapsulation offload (data frames in 802.3 format)

* support channel 2 in 6 GHz band

ath10k

* include frame time stamp in beacon and probe response frames

wcn36xx

* enable Idle Mode Power Save (IMPS) to reduce power consumption during idle
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net: add a helpers for loading netdev->dev_addr from FW

We're trying to make all writes to netdev->dev_addr go via helpers.
A lot of places pass netdev->dev_addr to of_get_ethdev_address() and
device_get_ethdev_addr() so this set adds new functions which wrap
the functionality.

v2 performs suggested code moves, adds a couple additional clean ups
on the device property side, and an extra patch converting drivers
which can benefit from device_get_ethdev_address().

v3 removes OF_NET and corrects kdoc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert a few drivers to device_get_ethdev_address(),
saving a few LoC.

The check if addr is valid in netsec is superfluous,
device_get_ethdev_addr() already checks that (in
fwnode_get_mac_addr()).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the new device_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.

  @@
  expression dev, np;
  @@
  - device_get_mac_address(np, dev->dev_addr, ETH_ALEN)
  + device_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>