- 07 Aug, 2017 9 commits
-
-
Paul Mackerras authored
commit ca8efa1d upstream. This adds code to save the values of three SPRs (special-purpose registers) used by userspace to control event-based branches (EBBs), which are essentially interrupts that get delivered directly to userspace. These registers are loaded up with guest values when entering the guest, and their values are saved when exiting the guest, but we were not saving the host values and restoring them before going back to userspace. On POWER8 this would only affect userspace programs which explicitly request the use of EBBs and also use the KVM_RUN ioctl, since the only source of EBBs on POWER8 is the PMU, and there is an explicit enable bit in the PMU registers (and those PMU registers do get properly context-switched between host and guest). On POWER9 there is provision for externally-generated EBBs, and these are not subject to the control in the PMU registers. Since these registers only affect userspace, we can save them when we first come in from userspace and restore them before returning to userspace, rather than saving/restoring the host values on every guest entry/exit. Similarly, we don't need to worry about their values on offline secondary threads since they execute in the context of the idle task, which never executes in userspace. Fixes: b005255e ("KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs", 2014-01-08) Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ben Skeggs authored
commit 38bcb208 upstream. Bit 30 being set causes the upper half of BAR2 to stay in physical mode, mapped over the end of VRAM, even when the rest of the BAR has been set to virtual mode. We inherited our initial value from RM, but I'm not aware of any reason we need to keep it that way. This fixes severe GPU hang/lockup issues revealed by Wayland on F26. Shout-out to NVIDIA for the quick response with the potential cause! Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Sinclair Yeh authored
commit fcfffdd8 upstream. The current code does not look correct, and the reason for it is probably lost. Since this now generates a compiler warning, fix it to what makes sense. Reported-by:
Arnd Bergmann <arnd@arndb.de> Reported-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Sinclair Yeh <syeh@vmware.com> Reviewed-by:
Brian Paul <brianp@vmware.com> Signed-off-by:
-
Ofer Heifetz authored
commit 7e96d559 upstream. Since thread_group worker and raid5d kthread are not in sync, if worker writes stripe before raid5d then requests will be waiting for issue_pendig. Issue observed when building raid5 with ext4, in some build runs jbd2 would get hung and requests were waiting in the HW engine waiting to be issued. Fix this by adding a call to async_tx_issue_pending_all in the raid5_do_work. Signed-off-by:
Ofer Heifetz <oferh@marvell.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Herbert Xu authored
commit 41cdf7a4 upstream. When authencesn is used together with digest_null a crash will occur on the decrypt path. This is because normally we perform a special setup to preserve the ESN, but this is skipped if there is no authentication. However, on the post-authentication path it always expects the preservation to be in place, thus causing a crash when digest_null is used. This patch fixes this by also skipping the post-processing when there is no authentication. Fixes: 104880a6 ("crypto: authencesn - Convert to new AEAD...") Reported-by:
Jan Tluka <jtluka@redhat.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Laurent Vivier authored
commit 4fd1bd44 upstream. As for commit 68baf692 ("powerpc/pseries: Fix of_node_put() underflow during DLPAR remove"), the call to of_node_put() must be removed from pSeries_reconfig_remove_node(). dlpar_detach_node() and pSeries_reconfig_remove_node() both call of_detach_node(), and thus the node should not be released in both cases. Fixes: 0829f6d1 ("of: device_node kobject lifecycle fixes") Signed-off-by:
Laurent Vivier <lvivier@redhat.com> Reviewed-by:
David Gibson <david@gibson.dropbear.id.au> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Eric Dumazet authored
commit b2504a5d upstream. Dmitry reported warnings occurring in __skb_gso_segment() [1] All SKB_GSO_DODGY producers can allow user space to feed packets that trigger the current check. We could prevent them from doing so, rejecting packets, but this might add regressions to existing programs. It turns out our SKB_GSO_DODGY handlers properly set up checksum information that is needed anyway when packets needs to be segmented. By checking again skb_needs_check() after skb_mac_gso_segment(), we should remove these pesky warnings, at a very minor cost. With help from Willem de Bruijn [1] WARNING: CPU: 1 PID: 6768 at net/core/dev.c:2439 skb_warn_bad_offload+0x2af/0x390 net/core/dev.c:2434 lo: caps=(0x000000a2803b7c69, 0x0000000000000000) len=138 data_len=0 gso_size=15883 gso_type=4 ip_summed=0 Kernel panic - not syncing: panic_on_warn set ... CPU: 1 PID: 6768 Comm: syz-executor1 Not tainted 4.9.0 #5 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 ffff8801c063ecd8 ffffffff82346bdf ffffffff00000001 1ffff100380c7d2e ffffed00380c7d26 0000000041b58ab3 ffffffff84b37e38 ffffffff823468f1 ffffffff84820740 ffffffff84f289c0 dffffc0000000000 ffff8801c063ee20 Call Trace: [<ffffffff82346bdf>] __dump_stack lib/dump_stack.c:15 [inline] [<ffffffff82346bdf>] dump_stack+0x2ee/0x3ef lib/dump_stack.c:51 [<ffffffff81827e34>] panic+0x1fb/0x412 kernel/panic.c:179 [<ffffffff8141f704>] __warn+0x1c4/0x1e0 kernel/panic.c:542 [<ffffffff8141f7e5>] warn_slowpath_fmt+0xc5/0x100 kernel/panic.c:565 [<ffffffff8356cbaf>] skb_warn_bad_offload+0x2af/0x390 net/core/dev.c:2434 [<ffffffff83585cd2>] __skb_gso_segment+0x482/0x780 net/core/dev.c:2706 [<ffffffff83586f19>] skb_gso_segment include/linux/netdevice.h:3985 [inline] [<ffffffff83586f19>] validate_xmit_skb+0x5c9/0xc20 net/core/dev.c:2969 [<ffffffff835892bb>] __dev_queue_xmit+0xe6b/0x1e70 net/core/dev.c:3383 [<ffffffff8358a2d7>] dev_queue_xmit+0x17/0x20 net/core/dev.c:3424 [<ffffffff83ad161d>] packet_snd net/packet/af_packet.c:2930 [inline] [<ffffffff83ad161d>] packet_sendmsg+0x32ed/0x4d30 net/packet/af_packet.c:2955 [<ffffffff834f0aaa>] sock_sendmsg_nosec net/socket.c:621 [inline] [<ffffffff834f0aaa>] sock_sendmsg+0xca/0x110 net/socket.c:631 [<ffffffff834f329a>] ___sys_sendmsg+0x8fa/0x9f0 net/socket.c:1954 [<ffffffff834f5e58>] __sys_sendmsg+0x138/0x300 net/socket.c:1988 [<ffffffff834f604d>] SYSC_sendmsg net/socket.c:1999 [inline] [<ffffffff834f604d>] SyS_sendmsg+0x2d/0x50 net/socket.c:1995 [<ffffffff84371941>] entry_SYSCALL_64_fastpath+0x1f/0xc2 Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Cc: Mark Salyzyn <salyzyn@android.com> Signed-off-by:
-
Joel Fernandes authored
commit 10970449 upstream. Currently pstore has a global spinlock for all zones. Since the zones are independent and modify different areas of memory, there's no need to have a global lock, so we should use a per-zone lock as introduced here. Also, when ramoops's ftrace use-case has a FTRACE_PER_CPU flag introduced later, which splits the ftrace memory area into a single zone per CPU, it will eliminate the need for locking. In preparation for this, make the locking optional. Signed-off-by:
Joel Fernandes <joelaf@google.com> [kees: updated commit message] Signed-off-by:
Kees Cook <keescook@chromium.org> Cc: Leo Yan <leo.yan@linaro.org> Signed-off-by:
-
Yuejie Shi authored
commit 89e357d8 upstream. A dump may come in the middle of another dump, modifying its dump structure members. This race condition will result in NULL pointer dereference in kernel. So add a lock to prevent that race. Fixes: 83321d6b ("[AF_KEY]: Dump SA/SP entries non-atomically") Signed-off-by:
Yuejie Shi <syjcnss@gmail.com> Signed-off-by:
Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by:
Mark Salyzyn <salyzyn@android.com> Signed-off-by:
-
- 27 Jul, 2017 31 commits
-
-
Greg Kroah-Hartman authored
-
Greg Hackmann authored
Commit ff86bf0c ("alarmtimer: Rate limit periodic intervals") sets a minimum bound on the alarm timer interval. This minimum bound shouldn't be applied if the interval is 0. Otherwise, one-shot timers will be converted into periodic ones. Fixes: ff86bf0c ("alarmtimer: Rate limit periodic intervals") Reported-by:
Ben Fennema <fennema@google.com> Signed-off-by:
Greg Hackmann <ghackmann@google.com> Cc: stable@vger.kernel.org Cc: John Stultz <john.stultz@linaro.org> Reviewed-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Chunyu Hu authored
commit db9108e0 upstream. Hit the kmemleak when executing instance_rmdir, it forgot releasing mem of tracing_cpumask. With this fix, the warn does not appear any more. unreferenced object 0xffff93a8dfaa7c18 (size 8): comm "mkdir", pid 1436, jiffies 4294763622 (age 9134.308s) hex dump (first 8 bytes): ff ff ff ff ff ff ff ff ........ backtrace: [<ffffffff88b6567a>] kmemleak_alloc+0x4a/0xa0 [<ffffffff8861ea41>] __kmalloc_node+0xf1/0x280 [<ffffffff88b505d3>] alloc_cpumask_var_node+0x23/0x30 [<ffffffff88b5060e>] alloc_cpumask_var+0xe/0x10 [<ffffffff88571ab0>] instance_mkdir+0x90/0x240 [<ffffffff886e5100>] tracefs_syscall_mkdir+0x40/0x70 [<ffffffff886565c9>] vfs_mkdir+0x109/0x1b0 [<ffffffff8865b1d0>] SyS_mkdir+0xd0/0x100 [<ffffffff88403857>] do_syscall_64+0x67/0x150 [<ffffffff88b710e7>] return_from_SYSCALL_64+0x0/0x6a [<ffffffffffffffff>] 0xffffffffffffffff Link: http://lkml.kernel.org/r/1500546969-12594-1-git-send-email-chuhu@redhat.com Fixes: ccfe9e42 ("tracing: Make tracing_cpumask available for all instances") Signed-off-by:
Chunyu Hu <chuhu@redhat.com> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Bjorn Andersson authored
commit d50daa2a upstream. Include the OF-based modalias in the uevent sent when registering SPMI devices, so that user space has a chance to autoload the kernel module for the device. Tested-by:
Rob Clark <robdclark@gmail.com> Reported-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
-
Stephen Boyd authored
commit 7a3b7cd3 upstream. The ULPI bus can be built as a module, and it will soon be calling these functions when it supports probing devices from DT. Export them so they can be used by the ULPI module. Acked-by:
Rob Herring <robh@kernel.org> Cc: <devicetree@vger.kernel.org> Signed-off-by:
Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
-
Imre Deak authored
commit 636c4c3e upstream. Currently we may process up/down message transactions containing uninitialized data. This can happen if there was an error during the reception of any message in the transaction, but we happened to receive the last message correctly with the end-of-message flag set. To avoid this abort the reception of the transaction when the first error is detected, rejecting any messages until a message with the start-of-message flag is received (which will start a new transaction). This is also what the DP 1.4 spec 2.11.8.2 calls for in this case. In addtion this also prevents receiving bogus transactions without the first message with the the start-of-message flag set. v2: - unchanged v3: - git add the part that actually skips messages after an error in drm_dp_sideband_msg_build() Cc: Dave Airlie <airlied@redhat.com> Cc: Lyude <lyude@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Imre Deak <imre.deak@intel.com> Reviewed-by:
Lyude <lyude@redhat.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20170719134632.13366-1-imre.deak@intel.comSigned-off-by:
-
Imre Deak authored
commit 7f8b3987 upstream. In case of an unknown broadcast message is sent mstb will remain unset, so check for this. Cc: Dave Airlie <airlied@redhat.com> Cc: Lyude <lyude@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Imre Deak authored
commit 448421b5 upstream. Handle any error due to partial reads, timeouts etc. to avoid parsing uninitialized data subsequently. Also bail out if the parsing itself fails. Cc: Dave Airlie <airlied@redhat.com> Cc: Lyude <lyude@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Ismail, Mustafa authored
commit a62ab66b upstream. Initialize the port_num for iWARP in rdma_init_qp_attr. Fixes: 5ecce4c9("Check port number supplied by user verbs cmds") Reviewed-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
Mustafa Ismail <mustafa.ismail@intel.com> Tested-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Yan, Zheng authored
commit 84583cfb upstream. For a large directory, program needs to issue multiple readdir syscalls to get all dentries. When there are multiple programs read the directory concurrently. Following sequence of events can happen. - program calls readdir with pos = 2. ceph sends readdir request to mds. The reply contains N1 entries. ceph adds these N1 entries to readdir cache. - program calls readdir with pos = N1+2. The readdir is satisfied by the readdir cache, N2 entries are returned. (Other program calls readdir in the middle, which fills the cache) - program calls readdir with pos = N1+N2+2. ceph sends readdir request to mds. The reply contains N3 entries and it reaches directory end. ceph adds these N3 entries to the readdir cache and marks directory complete. The second readdir call does not update fi->readdir_cache_idx. ceph add the last N3 entries to wrong places. Signed-off-by:
"Yan, Zheng" <zyan@redhat.com> Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Signed-off-by:
-
Michael Gugino authored
commit 5a1d4c5d upstream. Add support for USB Device TP-Link TL-WN722N v2. VendorID: 0x2357, ProductID: 0x010c Signed-off-by:
Michael Gugino <michael.gugino.2@gmail.com> Signed-off-by:
-
Ingo Molnar authored
commit 6a8a75f3 upstream. This reverts commit cc1582c2. This commit introduced a regression that broke rr-project, which uses sampling events to receive a signal on overflow (but does not care about the contents of the sample). These signals are critical to the correct operation of rr. There's been some back and forth about how to fix it - but to not keep applications in limbo queue up a revert. Reported-by:
Kyle Huey <me@kylehuey.com> Acked-by:
Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Stephane Eranian <eranian@google.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Link: http://lkml.kernel.org/r/20170628105600.GC5981@leverpostejSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Jin Yao authored
commit 80f62589 upstream. When the jump instruction is displayed at the row 0 in annotate view, the arrow is broken. An example: 16.86 │ ┌──je 82 0.01 │ movsd (%rsp),%xmm0 │ movsd 0x8(%rsp),%xmm4 │ movsd 0x8(%rsp),%xmm1 │ movsd (%rsp),%xmm3 │ divsd %xmm4,%xmm0 │ divsd %xmm3,%xmm1 │ movsd (%rsp),%xmm2 │ addsd %xmm1,%xmm0 │ addsd %xmm2,%xmm0 │ movsd %xmm0,(%rsp) │82: sub $0x1,%ebx 83.03 │ ↑ jne 38 │ add $0x10,%rsp │ xor %eax,%eax │ pop %rbx │ ← retq The patch increments the row number before checking with 0. Signed-off-by:
Yao Jin <yao.jin@linux.intel.com> Tested-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@intel.com> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: 944e1abe ("perf ui browser: Add method to draw up/down arrow line") Link: http://lkml.kernel.org/r/1496901704-30275-1-git-send-email-yao.jin@linux.intel.comSigned-off-by:
-
Jiang Yi authored
commit 1d6ef276 upstream. This patch addresses a COMPARE_AND_WRITE se_device->caw_sem leak, that would be triggered during normal se_cmd shutdown or abort via __transport_wait_for_tasks(). This would occur because target_complete_cmd() would catch this early and do complete_all(&cmd->t_transport_stop_comp), but since target_complete_ok_work() or target_complete_failure_work() are never called to invoke se_cmd->transport_complete_callback(), the COMPARE_AND_WRITE specific callbacks never release caw_sem. To address this special case, go ahead and release caw_sem directly from target_complete_cmd(). (Remove '&& success' from check, to release caw_sem regardless of scsi_status - nab) Signed-off-by:
Jiang Yi <jiangyilism@gmail.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Jan Kara authored
commit f2e95355 upstream. udf_setsize() called truncate_setsize() with i_data_sem held. Thus truncate_pagecache() called from truncate_setsize() could lock a page under i_data_sem which can deadlock as page lock ranks below i_data_sem - e. g. writeback can hold page lock and try to acquire i_data_sem to map a block. Fix the problem by moving truncate_setsize() calls from under i_data_sem. It is safe for us to change i_size without holding i_data_sem as all the places that depend on i_size being stable already hold inode_lock. Fixes: 7e49b6f2Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
NeilBrown authored
commit cc89684c upstream. Since commit bafc9b75 ("vfs: More precise tests in d_invalidate") in v3.18, a return of '0' from ->d_revalidate() will cause the dentry to be invalidated even if it has filesystems mounted on or it or on a descendant. The mounted filesystem is unmounted. This means we need to be careful not to return 0 unless the directory referred to truly is invalid. So -ESTALE or -ENOENT should invalidate the directory. Other errors such a -EPERM or -ERESTARTSYS should be returned from ->d_revalidate() so they are propagated to the caller. A particular problem can be demonstrated by: 1/ mount an NFS filesystem using NFSv3 on /mnt 2/ mount any other filesystem on /mnt/foo 3/ ls /mnt/foo 4/ turn off network, or otherwise make the server unable to respond 5/ ls /mnt/foo & 6/ cat /proc/$!/stack # note that nfs_lookup_revalidate is in the call stack 7/ kill -9 $! # this results in -ERESTARTSYS being returned 8/ observe that /mnt/foo has been unmounted. This patch changes nfs_lookup_revalidate() to only treat -ESTALE from nfs_lookup_verify_inode() and -ESTALE or -ENOENT from ->lookup() as indicating an invalid inode. Other errors are returned. Also nfs_check_inode_attributes() is changed to return -ESTALE rather than -EIO. This is consistent with the error returned in similar circumstances from nfs_update_inode(). As this bug allows any user to unmount a filesystem mounted on an NFS filesystem, this fix is suitable for stable kernels. Fixes: bafc9b75 ("vfs: More precise tests in d_invalidate") Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Chen Hong authored
commit 340d394a upstream. The driver checks port->exists twice in i8042_interrupt(), first when trying to assign temporary "serio" variable, and second time when deciding whether it should call serio_interrupt(). The value of port->exists may change between the 2 checks, and we may end up calling serio_interrupt() with a NULL pointer: BUG: unable to handle kernel NULL pointer dereference at 0000000000000050 IP: [<ffffffff8150feaf>] _spin_lock_irqsave+0x1f/0x40 PGD 0 Oops: 0002 [#1] SMP last sysfs file: CPU 0 Modules linked in: Pid: 1, comm: swapper Not tainted 2.6.32-358.el6.x86_64 #1 QEMU Standard PC (i440FX + PIIX, 1996) RIP: 0010:[<ffffffff8150feaf>] [<ffffffff8150feaf>] _spin_lock_irqsave+0x1f/0x40 RSP: 0018:ffff880028203cc0 EFLAGS: 00010082 RAX: 0000000000010000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000282 RSI: 0000000000000098 RDI: 0000000000000050 RBP: ffff880028203cc0 R08: ffff88013e79c000 R09: ffff880028203ee0 R10: 0000000000000298 R11: 0000000000000282 R12: 0000000000000050 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000098 FS: 0000000000000000(0000) GS:ffff880028200000(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 0000000000000050 CR3: 0000000001a85000 CR4: 00000000001407f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process swapper (pid: 1, threadinfo ffff88013e79c000, task ffff88013e79b500) Stack: ffff880028203d00 ffffffff813de186 ffffffffffffff02 0000000000000000 <d> 0000000000000000 0000000000000000 0000000000000000 0000000000000098 <d> ffff880028203d70 ffffffff813e0162 ffff880028203d20 ffffffff8103b8ac Call Trace: <IRQ> [<ffffffff813de186>] serio_interrupt+0x36/0xa0 [<ffffffff813e0162>] i8042_interrupt+0x132/0x3a0 [<ffffffff8103b8ac>] ? kvm_clock_read+0x1c/0x20 [<ffffffff8103b8b9>] ? kvm_clock_get_cycles+0x9/0x10 [<ffffffff810e1640>] handle_IRQ_event+0x60/0x170 [<ffffffff8103b154>] ? kvm_guest_apic_eoi_write+0x44/0x50 [<ffffffff810e3d8e>] handle_edge_irq+0xde/0x180 [<ffffffff8100de89>] handle_irq+0x49/0xa0 [<ffffffff81516c8c>] do_IRQ+0x6c/0xf0 [<ffffffff8100b9d3>] ret_from_intr+0x0/0x11 [<ffffffff81076f63>] ? __do_softirq+0x73/0x1e0 [<ffffffff8109b75b>] ? hrtimer_interrupt+0x14b/0x260 [<ffffffff8100c1cc>] ? call_softirq+0x1c/0x30 [<ffffffff8100de05>] ? do_softirq+0x65/0xa0 [<ffffffff81076d95>] ? irq_exit+0x85/0x90 [<ffffffff81516d80>] ? smp_apic_timer_interrupt+0x70/0x9b [<ffffffff8100bb93>] ? apic_timer_interrupt+0x13/0x20 To avoid the issue let's change the second check to test whether serio is NULL or not. Also, let's take i8042_lock in i8042_start() and i8042_stop() instead of trying to be overly smart and using memory barriers. Signed-off-by:
Chen Hong <chenhong3@huawei.com> [dtor: take lock in i8042_start()/i8042_stop()] Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Maciej W. Rozycki authored
commit 27fe2200 upstream. This is a user-visible message, so we want it to be spelled correctly. Fixes: 5f9f41c4 ("MIPS: kernel: Prepare the JR instruction for emulation on MIPS R6") Signed-off-by:
Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16400/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Maciej W. Rozycki authored
commit fef40be6 upstream. Fix commit 319824ea ("MIPS: kernel: branch: Do not emulate the branch likelies on MIPS R6") and also send SIGILL rather than returning -SIGILL for BLTZAL, BLTZALL, BGEZAL and BGEZALL instruction encodings no longer supported in R6, except where emulated. Returning -SIGILL is never correct as the API defines this function's result upon error to be -EFAULT and a signal actually issued. Fixes: 319824ea ("MIPS: kernel: branch: Do not emulate the branch likelies on MIPS R6") Signed-off-by:
-
Maciej W. Rozycki authored
commit 1f4edde4 upstream. Use the more accurate `sigill_r2r6' name for the label used in the case of sending SIGILL in the absence of the instruction emulator for an earlier ISA level instruction that has been removed as from the R6 ISA, so that the `sigill_r6' name is freed for the situation where an R6 instruction is not supposed to be interpreted, because the executing processor does not support the R6 ISA. Signed-off-by:
-
Maciej W. Rozycki authored
commit 7b82c105 upstream. Fix commit e50c0a8f ("Support the MIPS32 / MIPS64 DSP ASE.") and send SIGILL rather than SIGBUS whenever an unimplemented BPOSGE32 DSP ASE instruction has been encountered in `__compute_return_epc_for_insn' as our Reserved Instruction exception handler would in response to an attempt to actually execute the instruction. Sending SIGBUS only makes sense for the unaligned PC case, since moved to `__compute_return_epc'. Adjust function documentation accordingly, correct formatting and use `pr_info' rather than `printk' as the other exit path already does. Fixes: e50c0a8f ("Support the MIPS32 / MIPS64 DSP ASE.") Signed-off-by:
-
Maciej W. Rozycki authored
commit 13769eba upstream. Terminate FPU emulation immediately whenever an ISA mode switch has been observed. This is so that we do not interpret machine code in the wrong mode, for example when a regular MIPS FPU instruction has been placed in a delay slot of a jump that switches into the MIPS16 mode, as with the following code (taken from a GCC test suite case): 00400650 <set_fast_math>: 400650: 3c020100 lui v0,0x100 400654: 03e00008 jr ra 400658: 44c2f800 ctc1 v0,c1_fcsr 40065c: 00000000 nop [...] 004012d0 <__libc_csu_init>: 4012d0: f000 6a02 li v0,2 4012d4: f150 0b1c la v1,3f9430 <_DYNAMIC-0x6df0> 4012d8: f400 3240 sll v0,16 4012dc: e269 addu v0,v1 4012de: 659a move gp,v0 4012e0: f00c 64f6 save a0-a2,48,ra,s0-s1 4012e4: 673c move s1,gp 4012e6: f010 9978 lw v1,-32744(s1) 4012ea: d204 sw v0,16(sp) 4012ec: eb40 jalr v1 4012ee: 653b move t9,v1 4012f0: f010 997c lw v1,-32740(s1) 4012f4: f030 9920 lw s1,-32736(s1) 4012f8: e32f subu v1,s1 4012fa: 326b sra v0,v1,2 4012fc: d206 sw v0,24(sp) 4012fe: 220c beqz v0,401318 <__libc_csu_init+0x48> 401300: 6800 li s0,0 401302: 99e0 lw a3,0(s1) 401304: 4801 addiu s0,1 401306: 960e lw a2,56(sp) 401308: 4904 addiu s1,4 40130a: 950d lw a1,52(sp) 40130c: 940c lw a0,48(sp) 40130e: ef40 jalr a3 401310: 653f move t9,a3 401312: 9206 lw v0,24(sp) 401314: ea0a cmp v0,s0 401316: 61f5 btnez 401302 <__libc_csu_init+0x32> 401318: 6476 restore 48,ra,s0-s1 40131a: e8a0 jrc ra Here `set_fast_math' is called from `40130e' (`40130f' with the ISA bit) and emulation triggers for the CTC1 instruction. As it is in a jump delay slot emulation continues from `401312' (`401313' with the ISA bit). However we have no path to handle MIPS16 FPU code emulation, because there are no MIPS16 FPU instructions. So the default emulation path is taken, interpreting a 32-bit word fetched by `get_user' from `401313' as a regular MIPS instruction, which is: 401313: f5ea0a92 sdc1 $f10,2706(t7) This makes the FPU emulator proceed with the supposed SDC1 instruction and consequently makes the program considered here terminate with SIGSEGV. A similar although less severe issue exists with pure-microMIPS processors in the case where similarly an FPU instruction is emulated in a delay slot of a register jump that (incorrectly) switches into the regular MIPS mode. A subsequent instruction fetch from the jump's target is supposed to cause an Address Error exception, however instead we proceed with regular MIPS FPU emulation. For simplicity then, always terminate the emulation loop whenever a mode change is detected, denoted by an ISA mode bit flip. As from commit 377cb1b6 ("MIPS: Disable MIPS16/microMIPS crap for platforms not supporting these ASEs.") the result of `get_isa16_mode' can be hardcoded to 0, so we need to examine the ISA mode bit by hand. This complements commit 102cedc3 ("MIPS: microMIPS: Floating point support.") which added JALX decoding to FPU emulation. Fixes: 102cedc3 ("MIPS: microMIPS: Floating point support.") Signed-off-by:
-
Maciej W. Rozycki authored
commit 11a3799d upstream. Fix a regression introduced with commit fb6883e5 ("MIPS: microMIPS: Support handling of delay slots.") and defer to `__compute_return_epc' if the ISA bit is set in EPC with non-MIPS16, non-microMIPS hardware, which will then arrange for a SIGBUS due to an unaligned instruction reference. Returning EPC here is never correct as the API defines this function's result to be either a negative error code on failure or one of 0 and BRANCH_LIKELY_TAKEN on success. Fixes: fb6883e5 ("MIPS: microMIPS: Support handling of delay slots.") Signed-off-by:
-
Maciej W. Rozycki authored
commit a9db101b upstream. Complement commit fb6883e5 ("MIPS: microMIPS: Support handling of delay slots.") and actually decode the regular MIPS JALX major instruction opcode, the handling of which has been added with the said commit for EPC calculation in `__compute_return_epc_for_insn'. Fixes: fb6883e5 ("MIPS: microMIPS: Support handling of delay slots.") Signed-off-by:
-
James Hogan authored
commit 49955d84 upstream. The MIPS sysmips system call handler may return directly from the MIPS_ATOMIC_SET case (mips_atomic_set()) to syscall_exit. This path restores the static (callee saved) registers, however they won't have been saved on entry to the system call. Use the save_static_function() macro to create a __sys_sysmips wrapper function which saves the static registers before calling sys_sysmips, so that the correct static register state is restored by syscall_exit. Fixes: f1e39a4a ("MIPS: Rewrite sysmips(MIPS_ATOMIC_SET, ...) in C with inline assembler") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/16149/Signed-off-by:
-
Maciej W. Rozycki authored
commit e5f5a5b0 upstream. Correct a commit 515a6393 ("MIPS: kernel: proc: Add MIPS R6 support to /proc/cpuinfo") regression that caused MIPS I systems to show no ISA levels supported in /proc/cpuinfo, e.g.: system type : Digital DECstation 2100/3100 machine : Unknown processor : 0 cpu model : R3000 V2.0 FPU V2.0 BogoMIPS : 10.69 wait instruction : no microsecond timers : no tlb_entries : 64 extra interrupt vector : no hardware watchpoint : no isa : ASEs implemented : shadow register sets : 1 kscratch registers : 0 package : 0 core : 0 VCED exceptions : not available VCEI exceptions : not available and similarly exclude `mips1' from the ISA list for any processors below MIPSr1. This is because the condition to show `mips1' on has been made `cpu_has_mips_r1' rather than newly-introduced `cpu_has_mips_1'. Use the correct condition then. Fixes: 515a6393 ("MIPS: kernel: proc: Add MIPS R6 support to /proc/cpuinfo") Signed-off-by:
Maciej W. Rozycki <macro@linux-mips.org> Reviewed-by:
-
Seunghun Han authored
commit e708e35b upstream. One of the rarely executed code pathes in check_timer() calls unmask_ioapic_irq() passing irq_get_chip_data(0) as argument. That's wrong as unmask_ioapic_irq() expects a pointer to the irq data of interrupt 0. irq_get_chip_data(0) returns NULL, so the following dereference in unmask_ioapic_irq() causes a kernel panic. The issue went unnoticed in the first place because irq_get_chip_data() returns a void pointer so the compiler cannot do a type check on the argument. The code path was added for machines with broken configuration, but it seems that those machines are either not running current kernels or simply do not longer exist. Hand in irq_get_irq_data(0) as argument which provides the correct data. [ tglx: Rewrote changelog ] Fixes: 4467715a ("x86/irq: Move irq_cfg.irq_2_pin into io_apic.c") Signed-off-by:
Seunghun Han <kkamagui@gmail.com> Signed-off-by:
-
Seunghun Han authored
commit dad5ab0d upstream. The bus_irq argument of mp_override_legacy_irq() is used as the index into the isa_irq_to_gsi[] array. The bus_irq argument originates from ACPI_MADT_TYPE_IO_APIC and ACPI_MADT_TYPE_INTERRUPT items in the ACPI tables, but is nowhere sanity checked. That allows broken or malicious ACPI tables to overwrite memory, which might cause malfunction, panic or arbitrary code execution. Add a sanity check and emit a warning when that triggers. [ tglx: Added warning and rewrote changelog ] Signed-off-by:
-
James Hogan authored
commit 4f32a39d upstream. The sys_exit trace event takes a single return value for the system call, which MIPS passes the value of the $v0 (result) register, however MIPS returns positive error codes in $v0 with $a3 specifying that $v0 contains an error code. As a result erroring system calls are traced returning positive error numbers that can't always be distinguished from success. Use regs_return_value() to negate the error code if $a3 is set. Fixes: 1d7bf993 ("MIPS: ftrace: Add support for syscall tracepoints.") Signed-off-by:
-
James Hogan authored
commit 4915e1b0 upstream. EVA linked loads (LLE) and conditional stores (SCE) should be used on EVA kernels for the MIPS_ATOMIC_SET operation of the sysmips system call, or else the atomic set will apply to the kernel view of the virtual address space (potentially unmapped on EVA kernels) rather than the user view (TLB mapped). Signed-off-by:
-
James Hogan authored
commit 2ec420b2 upstream. The inline asm retry check in the MIPS_ATOMIC_SET operation of the sysmips system call has been backwards since commit f1e39a4a ("MIPS: Rewrite sysmips(MIPS_ATOMIC_SET, ...) in C with inline assembler") merged in v2.6.32, resulting in the non R10000_LLSC_WAR case retrying until the operation was inatomic, before returning the new value that was probably just written multiple times instead of the old value. Invert the branch condition to fix that particular issue. Fixes: f1e39a4a ("MIPS: Rewrite sysmips(MIPS_ATOMIC_SET, ...) in C with inline assembler") Signed-off-by:
-
