[ Upstream commit d9829988 ]

On my R9 390, the voltage was reported as a constant 1000 mV.
This was due to a bug in smu7_hwmgr.c, in the smu7_read_sensor()
function, where some magic constants were used in a condition,
to determine whether the voltage should be read from PLANE2_VID
or PLANE1_VID. The VDDC mask was incorrectly used, instead of
the VDDGFX mask.

This patch changes the code to use the correct defined constants
(and apply the correct bitshift), thus resulting in correct voltage reporting.
Signed-off-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 13774d81 ]

In snd_hdac_device_init pm_runtime_set_active is called to
increase child_count in parent device. But when it is failed
to build connection with GPU for one case that integrated
graphic gpu is disabled, snd_hdac_ext_bus_device_exit will be
invoked to clean up a HD-audio extended codec base device. At
this time the child_count of parent is not decreased, which
makes parent device can't get suspended.

This patch calls pm_runtime_set_suspended to decrease child_count
in parent device in snd_hdac_device_exit to match with
snd_hdac_device_init. pm_runtime_set_suspended can make sure that
it will not decrease child_count if the device is already suspended.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20200902154218.1440441-1-kai.vehmanen@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit eacc9c5a ]

This fixes the behavior of the scaling_max_freq and scaling_min_freq
sysfs files in systems which had turbo disabled by the BIOS.

Caleb noticed that the HWP is programmed to operate in the wrong
P-state range on his system when the CPUFREQ policy min/max frequency
is set via sysfs.  This seems to be because in his system
intel_pstate_get_hwp_max() is returning the maximum turbo P-state even
though turbo was disabled by the BIOS, which causes intel_pstate to
scale kHz frequencies incorrectly e.g. setting the maximum turbo
frequency whenever the maximum guaranteed frequency is requested via
sysfs.
Tested-by: Caleb Callaway <caleb.callaway@intel.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Minor subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 43298db3 ]

After commit f6ebbcf0 ("cpufreq: intel_pstate: Implement passive
mode with HWP enabled") it is possible to change the driver status
to "off" via sysfs with HWP enabled, which effectively causes the
driver to unregister itself, but HWP remains active and it forces the
minimum performance, so even if another cpufreq driver is loaded,
it will not be able to control the CPU frequency.

For this reason, make the driver refuse to change the status to
"off" with HWP enabled.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 26907eb6 ]

HSDK board has Micrel KSZ9031, recent commit
bcf3440c ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
caused a breakdown of Ethernet.
Using 'phy-mode = "rgmii"' is not correct because accodring RGMII
specification it is necessary to have delay on RX (PHY to MAX)
which is not generated in case of "rgmii".
Using "rgmii-id" adds necessary delay and solves the issue.

Also adding name of PHY placed on HSDK board.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b7429ea5 ]

When input_mt_init_slots() fails, input should be freed
to prevent memleak. When input_register_device() fails,
we should call input_mt_destroy_slots() to free memory
allocated by input_mt_init_slots().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1a545ebe ]

This driver didn't set hard_header_len. This patch sets hard_header_len
for it according to its header_ops->create function.

This driver's header_ops->create function (cisco_hard_header) creates
a header of (struct hdlc_header), so hard_header_len should be set to
sizeof(struct hdlc_header).

Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 77df710b ]

The Saitek X52 family of joysticks has a pair of axes that were
originally (by the Windows driver) used as mouse pointer controls. The
corresponding usage page is the Game Controls page, which is not
recognized by the generic HID driver, and therefore, both axes get
mapped to ABS_MISC. The quirk makes the second axis get mapped to
ABS_MISC+1, and therefore made available separately.

One Saitek X52 device is already fixed. This patch fixes the other two
known devices with VID/PID 06a3:0255 and 06a3:0762.
Signed-off-by: Nirenjan Krishnan <nirenjan@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5110f402 ]

In the timeout handler we may need to complete a request because the
request that timed out may be an I/O that is a part of a serial sequence
of controller teardown or initialization. In order to complete the
request, we need to fence any other context that may compete with us
and complete the request that is timing out.

In this case, we could have a potential double completion in case
a hard-irq or a different competing context triggered error recovery
and is running inflight request cancellation concurrently with the
timeout handler.

Protect using a ctrl teardown_lock to serialize contexts that may
complete a cancelled request due to error recovery or a reset.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d7144f5c ]

NVME_CTRL_NEW should never see any I/O, because in order to start
initialization it has to transition to NVME_CTRL_CONNECTING and from
there it will never return to this state.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 89d29997 ]

eznps driver is supposed to be platform independent however it ends up
including stuff from inside arch/arc headers leading to rand config
build errors.

The quick hack to fix this (proper fix is too much chrun for non active
user-base) is to add following to nps platform agnostic header.
 - copy AUX_IENABLE from arch/arc header
 - move CTOP_AUX_IACK from arch/arc/plat-eznps/*/**
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lkml.kernel.org/r/20200824095831.5lpkmkafelnvlpi2@linutronix.deSigned-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 125eac24 ]

Don't leak kernel memory contents into the shortform attr fork.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 91244d10 ]

Set the skb's network_header before it is passed to the underlying
Ethernet device for transmission.

This patch fixes the following issue:

When we use this driver with AF_PACKET sockets, there would be error
messages of:
   protocol 0805 is buggy, dev (Ethernet interface name)
printed in the system "dmesg" log.

This is because skbs passed down to the Ethernet device for transmission
don't have their network_header properly set, and the dev_queue_xmit_nit
function in net/core/dev.c complains about this.

Reason of setting the network_header to this place (at the end of the
Ethernet header, and at the beginning of the Ethernet payload):

Because when this driver receives an skb from the Ethernet device, the
network_header is also set at this place.

Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 216116ea ]

The Tegra HDA codec HW implementation has an issue related to not
swapping the 2 channel Audio Sample Packet(ASP) channel mapping.
Whatever the FL and FR mapping specified the left channel always
comes out of left speaker and right channel on right speaker. So
add condition to disallow the swapping of FL,FR during the playback.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Acked-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/20200825052415.20626-2-mkumard@nvidia.comSigned-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 15ac5cda ]

When make_rate() fails, vcc should be freed just
like other error paths in fs_open().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f97c04c3 ]

When down_killable() fails, skb_resp should be freed
just like when st95hf_spi_send() fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1ee39c14 ]

The underlying Ethernet device may request necessary tailroom to be
allocated by setting needed_tailroom. This driver should also set
needed_tailroom to request the tailroom needed by the underlying
Ethernet device to be allocated.

Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit cc5453a5 ]

If an sctp connection gets re-used, heartbeats are flagged as invalid
because their vtag doesn't match.

Handle this in a similar way as TCP conntrack when it suspects that the
endpoints and conntrack are out-of-sync.

When a HEARTBEAT request fails its vtag validation, flag this in the
conntrack state and accept the packet.

When a HEARTBEAT_ACK is received with an invalid vtag in the reverse
direction after we allowed such a HEARTBEAT through, assume we are
out-of-sync and re-set the vtag info.

v2: remove left-over snippet from an older incarnation that moved
    new_state/old_state assignments, thats not needed so keep that
    as-is.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7eb48dd0 ]

The acpi_get_table() should be coupled with acpi_put_table() if
the mapped table is not used at runtime to release the table
mapping, put the CSRT table buf after using it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/1595411661-15936-1-git-send-email-guohanjun@huawei.comSigned-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit fe81d927 ]

Newer version of HSDK aka HSDK-4xD (with dual issue HS48x4 CPU) wired up
the perf interrupt, so enable that in DT.
This is OK for old HSDK where this irq is ignored because pct irq is not
wired up in hardware.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 686e0a0c ]

The string was incorrectly defined before from least to most specific,
swap the compatible strings accordingly.

Fixes: ff73917d ("ARM64: dts: Add QSPI Device Tree node for NS2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b793dab8 ]

The string was incorrectly defined before from least to most
specific, swap the compatible strings accordingly.

Fixes: 1c8f4065 ("ARM: dts: BCM5301X: convert to iProc QSPI")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d1ecc40a ]

The string was incorrectly defined before from least to most
specific, swap the compatible strings accordingly.

Fixes: 329f98c1 ("ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d6631862 ]

The string was incorrectly defined before from least to most specific,
swap the compatible strings accordingly.

Fixes: b9099ec7 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9d5dcefb ]

As the comments in this patch say, if we tune and find all phases are
valid it's _almost_ as bad as no phases being found valid.  Probably
all phases are not really reliable but we didn't detect where the
unreliable place is.  That means we'll essentially be guessing and
hoping we get a good phase.

This is not just a problem in theory.  It was causing real problems on
a real board.  On that board, most often phase 10 is found as the only
invalid phase, though sometimes 10 and 11 are invalid and sometimes
just 11.  Some percentage of the time, however, all phases are found
to be valid.  When this happens, the current logic will decide to use
phase 11.  Since phase 11 is sometimes found to be invalid, this is a
bad choice.  Sure enough, when phase 11 is picked we often get mmc
errors later in boot.

I have seen cases where all phases were found to be valid 3 times in a
row, so increase the retry count to 10 just to be extra sure.

Fixes: 415b5a75 ("mmc: sdhci-msm: Add platform_execute_tuning implementation")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200827075809.1.If179abf5ecb67c963494db79c3bc4247d987419b@changeidSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 28b08657 ]

When the returned speed from __ethtool_get_link_ksettings() is
SPEED_UNKNOWN this will lead to reporting a wrong speed and width for
providers that uses ib_get_eth_speed(), fix that by defaulting the
netdev_speed to SPEED_1000 in case the returned value from
__ethtool_get_link_ksettings() is SPEED_UNKNOWN.

Fixes: d4186194 ("IB/core: Add generic function to extract IB speed from netdev")
Link: https://lore.kernel.org/r/20200902124304.170912-1-kamalheib1@gmail.comSigned-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 53de092f ]

It was discovered that sdparm will fail when attempting to disable write
cache on a SATA disk connected via libsas.

In the ATA command set the write cache state is controlled through the SET
FEATURES operation. This is roughly corresponds to MODE SELECT in SCSI and
the latter command is what is used in the SCSI-ATA translation layer. A
subtle difference is that a MODE SELECT carries data whereas SET FEATURES
is defined as a non-data command in ATA.

Set the DMA data direction to DMA_NONE if the requested ATA command is
identified as non-data.

[mkp: commit desc]

Fixes: fa1c1e8f ("[SCSI] Add SATA support to libsas")
Link: https://lore.kernel.org/r/1598426666-54544-1-git-send-email-luojiaxing@huawei.comReviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit fd90e380 ]

It's writing too much data. regmap_bulk_write expects number of
register sized chunks to write, not a byte sized length of the
bounce buffer. Bounce buffer needs to be padded too, so that
regmap_bulk_write will not read past the end of the buffer.

Fixes: 133add5b ("drm/sun4i: Add Allwinner A31 MIPI-DSI controller support")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200828125032.937148-1-megous@megous.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2d0e60ee ]

QP1 Rx CQE reports transparent VLAN ID in the completion and this is used
while reporting the completion for received MAD packet. Check if the vlan
id is configured before reporting it in the work completion.

Fixes: 84511455 ("RDMA/bnxt_re: report vlan_id and sl in qp1 recv completion")
Link: https://lore.kernel.org/r/1598292876-26529-3-git-send-email-selvin.xavier@broadcom.comSigned-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6112ef62 ]

Both pkey_tbl_len and gid_tbl_len are set in rxe_init_port_param() - so no
need to check if they aren't set.

Fixes: 8700e3e7 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20200705104313.283034-2-kamalheib1@gmail.comSigned-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e3ddd606 ]

When page_address() fails, umem should be freed just like when
rxe_mem_alloc() fails.

Fixes: 8700e3e7 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20200819075632.22285-1-dinghao.liu@zju.edu.cnSigned-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 81dbbb41 ]

According to the Reference Manual, the correct size is 512 MiB.

Without this fix, probing the QSPI fails:

    fsl-quadspi 1550000.spi: ioremap failed for resource
        [mem 0x40000000-0x7fffffff]
    fsl-quadspi 1550000.spi: Freescale QuadSPI probe failed
    fsl-quadspi: probe of 1550000.spi failed with error -12

Fixes: 85f8ee78 ("ARM: dts: ls1021a: Add support for QSPI with ls1021a SoC")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0ff5a481 ]

Fixes the register address for the timer3 entry on Arria10.

Fixes: 475dc86d ("arm: dts: socfpga: Add a base DTSI for Altera's Arria10 SOC")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4d26e9a0 ]

Older versions of U-Boot would pinmux the whole board, but as
the bootloader got updated, it started to only pinmux the pins
it needed, and expected Linux to configure what it needed.

Unfortunately this caused an issue with the audio, because the
mcbsp2 pins were configured in the device tree but never
referenced by the driver. When U-Boot stopped muxing the audio
pins, the audio died.

This patch adds the references to the associate the pin controller
with the mcbsp2 driver which makes audio operate again.

Fixes: 5cb8b0fa ("ARM: dts: Move most of logicpd-som-lv-37xx-devkit.dts to logicpd-som-lv-baseboard.dtsi")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d7dfee67 ]

Older versions of U-Boot would pinmux the whole board, but as
the bootloader got updated, it started to only pinmux the pins
it needed, and expected Linux to configure what it needed.

Unfortunately this caused an issue with the audio, because the
mcbsp2 pins were configured in the device tree, they were never
referenced by the driver. When U-Boot stopped muxing the audio
pins, the audio died.

This patch adds the references to the associate the pin controller
with the mcbsp2 driver which makes audio operate again.

Fixes: 739f85bb ("ARM: dts: Move most of logicpd-torpedo-37xx-devkit to logicpd-torpedo-baseboard")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Support for phys switch id ndo added for representors and if
we do not have representors there is no need to support it.
Since each port return different switch id supporting this
block support for creating bond over PFs and attaching to bridge
in legacy mode.

This bug doesn't exist upstream as the code got refactored and the
netdev api is totally different.

Fixes: cb67b832 ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 96e97bc0 ]

napi_disable() makes sure to set the NAPI_STATE_NPSVC bit to prevent
netpoll from accessing rings before init is complete. However, the
same is not done for fresh napi instances in netif_napi_add(),
even though we expect NAPI instances to be added as disabled.

This causes crashes during driver reconfiguration (enabling XDP,
changing the channel count) - if there is any printk() after
netif_napi_add() but before napi_enable().

To ensure memory ordering is correct we need to use RCU accessors.
Reported-by: Rob Sherwood <rsher@fb.com>
Fixes: 2d8bff12 ("netpoll: Close race condition between poll_one_napi and napi_disable")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2a63866c ]

syzbot is reporting hung task at nbd_ioctl() [1], for there are two
problems regarding TIPC's connectionless socket's shutdown() operation.

----------
#include <fcntl.h>
#include <sys/socket.h>
#include <sys/ioctl.h>
#include <linux/nbd.h>
#include <unistd.h>

int main(int argc, char *argv[])
{
        const int fd = open("/dev/nbd0", 3);
        alarm(5);
        ioctl(fd, NBD_SET_SOCK, socket(PF_TIPC, SOCK_DGRAM, 0));
        ioctl(fd, NBD_DO_IT, 0); /* To be interrupted by SIGALRM. */
        return 0;
}
----------

One problem is that wait_for_completion() from flush_workqueue() from
nbd_start_device_ioctl() from nbd_ioctl() cannot be completed when
nbd_start_device_ioctl() received a signal at wait_event_interruptible(),
for tipc_shutdown() from kernel_sock_shutdown(SHUT_RDWR) from
nbd_mark_nsock_dead() from sock_shutdown() from nbd_start_device_ioctl()
is failing to wake up a WQ thread sleeping at wait_woken() from
tipc_wait_for_rcvmsg() from sock_recvmsg() from sock_xmit() from
nbd_read_stat() from recv_work() scheduled by nbd_start_device() from
nbd_start_device_ioctl(). Fix this problem by always invoking
sk->sk_state_change() (like inet_shutdown() does) when tipc_shutdown() is
called.

The other problem is that tipc_wait_for_rcvmsg() cannot return when
tipc_shutdown() is called, for tipc_shutdown() sets sk->sk_shutdown to
SEND_SHUTDOWN (despite "how" is SHUT_RDWR) while tipc_wait_for_rcvmsg()
needs sk->sk_shutdown set to RCV_SHUTDOWN or SHUTDOWN_MASK. Fix this
problem by setting sk->sk_shutdown to SHUTDOWN_MASK (like inet_shutdown()
does) when the socket is connectionless.

[1] https://syzkaller.appspot.com/bug?id=3fe51d307c1f0a845485cf1798aa059d12bf18b2Reported-by: syzbot <syzbot+e36f41d207137b5d12f7@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 3106ecb4 ]

With disabling bh in the whole sctp_get_port_local(), when
snum == 0 and too many ports have been used, the do-while
loop will take the cpu for a long time and cause cpu stuck:

  [ ] watchdog: BUG: soft lockup - CPU#11 stuck for 22s!
  [ ] RIP: 0010:native_queued_spin_lock_slowpath+0x4de/0x940
  [ ] Call Trace:
  [ ]  _raw_spin_lock+0xc1/0xd0
  [ ]  sctp_get_port_local+0x527/0x650 [sctp]
  [ ]  sctp_do_bind+0x208/0x5e0 [sctp]
  [ ]  sctp_autobind+0x165/0x1e0 [sctp]
  [ ]  sctp_connect_new_asoc+0x355/0x480 [sctp]
  [ ]  __sctp_connect+0x360/0xb10 [sctp]

There's no need to disable bh in the whole function of
sctp_get_port_local. So fix this cpu stuck by removing
local_bh_disable() called at the beginning, and using
spin_lock_bh() instead.

The same thing was actually done for inet_csk_get_port() in
Commit ea8add2b ("tcp/dccp: better use of ephemeral
ports in bind()").

Thanks to Marcelo for pointing the buggy code out.

v1->v2:
  - use cond_resched() to yield cpu to other tasks if needed,
    as Eric noticed.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>