- 16 Mar, 2017 40 commits
-
-
Bjørn Mork authored
[ Upstream commit c086e709 ] Several Lenovo users have reported problems with their Sierra Wireless EM7455 modem. The driver has loaded successfully and the MBIM management channel has appeared to work, including establishing a connection to the mobile network. But no frames have been received over the data interface. The problem affects all EM7455 and MC7455, and is assumed to affect other modems based on the same Qualcomm chipset and baseband firmware. Testing narrowed the problem down to what seems to be a firmware timing bug during initialization. Adding a short sleep while probing is sufficient to make the problem disappear. Experiments have shown that 1-2 ms is too little to have any effect, while 10-20 ms is enough to reliably succeed. Reported-by:
Stefan Armbruster <ml001@armbruster-it.de> Reported-by:
Ralph Plawetzki <ralph@purejava.org> Reported-by:
Andreas Fett <andreas.fett@secunet.com> Reported-by:
Rasmus Lerdorf <rasmus@lerdorf.com> Reported-by:
Samo Ratnik <samo.ratnik@gmail.com> Reported-and-tested-by:
Aleksander Morgado <aleksander@aleksander.es> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Feng Tang authored
[ Upstream commit 881d0327 ] Note: This is a verified backported patch for stable 4.4 kernel, and it could also be applied to 4.3/4.2/4.1/3.18/3.16 There is a problem with alx devices, that the network link will be lost in 1-5 minutes after the device is up. >From debugging without datasheet, we found the error always happen when the DMA RX address is set to 0x....fc0, which is very likely to be a HW/silicon problem. This patch will apply rx skb with 64 bytes longer space, and if the allocated skb has a 0x...fc0 address, it will use skb_resever(skb, 64) to advance the address, so that the RX overflow can be avoided. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70761Signed-off-by:
Feng Tang <feng.tang@intel.com> Suggested-by:
Eric Dumazet <edumazet@google.com> Tested-by:
Ole Lukoie <olelukoie@mail.ru> Signed-off-by:
-
Tom Goff authored
[ Upstream commit 70a0dec4 ] This fixes wrong-interface signaling on 32-bit platforms for entries created when jiffies > 2^31 + MFC_ASSERT_THRESH. Signed-off-by:
Tom Goff <thomas.goff@ll.mit.edu> Signed-off-by:
-
Simon Horman authored
[ Upstream commit d5d8760b ] Since 32b8a8e5 ("sit: add IPv4 over IPv4 support") ipip6_err() may be called for packets whose IP protocol is IPPROTO_IPIP as well as those whose IP protocol is IPPROTO_IPV6. In the case of IPPROTO_IPIP packets the correct protocol value is not passed to ipv4_update_pmtu() or ipv4_redirect(). This patch resolves this problem by using the IP protocol of the packet rather than a hard-coded value. This appears to be consistent with the usage of the protocol of a packet by icmp_socket_deliver() the caller of ipip6_err(). I was able to exercise the redirect case by using a setup where an ICMP redirect was received for the destination of the encapsulated packet. However, it appears that although incorrect the protocol field is not used in this case and thus no problem manifests. On inspection it does not appear that a problem will manifest in the fragmentation needed/update pmtu case either. In short I believe this is a cosmetic fix. None the less, the use of IPPROTO_IPV6 seems wrong and confusing. Reviewed-by:
Dinan Gunawardena <dinan.gunawardena@netronome.com> Signed-off-by:
Simon Horman <simon.horman@netronome.com> Acked-by:
YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by:
-
Jakub Sitnicki authored
[ Upstream commit 00bc0ef5 ] At present we perform an xfrm_lookup() for each UDPv6 message we send. The lookup involves querying the flow cache (flow_cache_lookup) and, in case of a cache miss, creating an XFRM bundle. If we miss the flow cache, we can end up creating a new bundle and deriving the path MTU (xfrm_init_pmtu) from on an already transformed dst_entry, which we pass from the socket cache (sk->sk_dst_cache) down to xfrm_lookup(). This can happen only if we're caching the dst_entry in the socket, that is when we're using a connected UDP socket. To put it another way, the path MTU shrinks each time we miss the flow cache, which later on leads to incorrectly fragmented payload. It can be observed with ESPv6 in transport mode: 1) Set up a transformation and lower the MTU to trigger fragmentation # ip xfrm policy add dir out src ::1 dst ::1 \ tmpl src ::1 dst ::1 proto esp spi 1 # ip xfrm state add src ::1 dst ::1 \ proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b # ip link set dev lo mtu 1500 2) Monitor the packet flow and set up an UDP sink # tcpdump -ni lo -ttt & # socat udp6-listen:12345,fork /dev/null & 3) Send a datagram that needs fragmentation with a connected socket # perl -e 'print "@" x 1470 | socat - udp6:[::1]:12345 2016/06/07 18:52:52 socat[724] E read(3, 0x555bb3d5ba00, 8192): Protocol error 00:00:00.000000 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x2), length 1448 00:00:00.000014 IP6 ::1 > ::1: frag (1448|32) 00:00:00.000050 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x3), length 1272 (^ ICMPv6 Parameter Problem) 00:00:00.000022 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x5), length 136 4) Compare it to a non-connected socket # perl -e 'print "@" x 1500' | socat - udp6-sendto:[::1]:12345 00:00:40.535488 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x6), length 1448 00:00:00.000010 IP6 ::1 > ::1: frag (1448|64) What happens in step (3) is: 1) when connecting the socket in __ip6_datagram_connect(), we perform an XFRM lookup, miss the flow cache, create an XFRM bundle, and cache the destination, 2) afterwards, when sending the datagram, we perform an XFRM lookup, again, miss the flow cache (due to mismatch of flowi6_iif and flowi6_oif, which is an issue of its own), and recreate an XFRM bundle based on the cached (and already transformed) destination. To prevent the recreation of an XFRM bundle, avoid an XFRM lookup altogether whenever we already have a destination entry cached in the socket. This prevents the path MTU shrinkage and brings us on par with UDPv4. The fix also benefits connected PINGv6 sockets, another user of ip6_sk_dst_lookup_flow(), who also suffer messages being transformed twice. Joint work with Hannes Frederic Sowa. Reported-by:
Jan Tluka <jtluka@redhat.com> Signed-off-by:
Jakub Sitnicki <jkbs@redhat.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit e5aed006 ] In case we find a socket with encapsulation enabled we should call the encap_recv function even if just a udp header without payload is available. The callbacks are responsible for correctly verifying and dropping the packets. Also, in case the header validation fails for geneve and vxlan we shouldn't put the skb back into the socket queue, no one will pick them up there. Instead we can simply discard them in the respective encap_recv functions. Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit 31ca0458 ] get_bridge_ifindices() is used from the old "deviceless" bridge ioctl calls which aren't called with rtnl held. The comment above says that it is called with rtnl but that is not really the case. Here's a sample output from a test ASSERT_RTNL() which I put in get_bridge_ifindices and executed "brctl show": [ 957.422726] RTNL: assertion failed at net/bridge//br_ioctl.c (30) [ 957.422925] CPU: 0 PID: 1862 Comm: brctl Tainted: G W O 4.6.0-rc4+ #157 [ 957.423009] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.8.1-20150318_183358- 04/01/2014 [ 957.423009] 0000000000000000 ffff880058adfdf0 ffffffff8138dec5 0000000000000400 [ 957.423009] ffffffff81ce8380 ffff880058adfe58 ffffffffa05ead32 0000000000000001 [ 957.423009] 00007ffec1a444b0 0000000000000400 ffff880053c19130 0000000000008940 [ 957.423009] Call Trace: [ 957.423009] [<ffffffff8138dec5>] dump_stack+0x85/0xc0 [ 957.423009] [<ffffffffa05ead32>] br_ioctl_deviceless_stub+0x212/0x2e0 [bridge] [ 957.423009] [<ffffffff81515beb>] sock_ioctl+0x22b/0x290 [ 957.423009] [<ffffffff8126ba75>] do_vfs_ioctl+0x95/0x700 [ 957.423009] [<ffffffff8126c159>] SyS_ioctl+0x79/0x90 [ 957.423009] [<ffffffff8163a4c0>] entry_SYSCALL_64_fastpath+0x23/0xc1 Since it only reads bridge ifindices, we can use rcu to safely walk the net device list. Also remove the wrong rtnl comment above. Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Ian Campbell authored
[ Upstream commit dedc58e0 ] The peer may be expecting a reply having sent a request and then done a shutdown(SHUT_WR), so tearing down the whole socket at this point seems wrong and breaks for me with a client which does a SHUT_WR. Looking at other socket family's stream_recvmsg callbacks doing a shutdown here does not seem to be the norm and removing it does not seem to have had any adverse effects that I can see. I'm using Stefan's RFC virtio transport patches, I'm unsure of the impact on the vmci transport. Signed-off-by:
Ian Campbell <ian.campbell@docker.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Stefan Hajnoczi <stefanha@redhat.com> Cc: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com> Cc: Andy King <acking@vmware.com> Cc: Dmitry Torokhov <dtor@vmware.com> Cc: Jorgen Hansen <jhansen@vmware.com> Cc: Adit Ranadive <aditr@vmware.com> Cc: netdev@vger.kernel.org Signed-off-by:
-
Neil Horman authored
[ Upstream commit 6071bd1a ] This was recently reported to me, and reproduced on the latest net kernel, when attempting to run netperf from a host that had a netem qdisc attached to the egress interface: [ 788.073771] ---------------------[ cut here ]--------------------------- [ 788.096716] WARNING: at net/core/dev.c:2253 skb_warn_bad_offload+0xcd/0xda() [ 788.129521] bnx2: caps=(0x00000001801949b3, 0x0000000000000000) len=2962 data_len=0 gso_size=1448 gso_type=1 ip_summed=3 [ 788.182150] Modules linked in: sch_netem kvm_amd kvm crc32_pclmul ipmi_ssif ghash_clmulni_intel sp5100_tco amd64_edac_mod aesni_intel lrw gf128mul glue_helper ablk_helper edac_mce_amd cryptd pcspkr sg edac_core hpilo ipmi_si i2c_piix4 k10temp fam15h_power hpwdt ipmi_msghandler shpchp acpi_power_meter pcc_cpufreq nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c sd_mod crc_t10dif crct10dif_generic mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit drm_kms_helper ahci ata_generic pata_acpi ttm libahci crct10dif_pclmul pata_atiixp tg3 libata crct10dif_common drm crc32c_intel ptp serio_raw bnx2 r8169 hpsa pps_core i2c_core mii dm_mirror dm_region_hash dm_log dm_mod [ 788.465294] CPU: 16 PID: 0 Comm: swapper/16 Tainted: G W ------------ 3.10.0-327.el7.x86_64 #1 [ 788.511521] Hardware name: HP ProLiant DL385p Gen8, BIOS A28 12/17/2012 [ 788.542260] ffff880437c036b8 f7afc56532a53db9 ffff880437c03670 ffffffff816351f1 [ 788.576332] ffff880437c036a8 ffffffff8107b200 ffff880633e74200 ffff880231674000 [ 788.611943] 0000000000000001 0000000000000003 0000000000000000 ffff880437c03710 [ 788.647241] Call Trace: [ 788.658817] <IRQ> [<ffffffff816351f1>] dump_stack+0x19/0x1b [ 788.686193] [<ffffffff8107b200>] warn_slowpath_common+0x70/0xb0 [ 788.713803] [<ffffffff8107b29c>] warn_slowpath_fmt+0x5c/0x80 [ 788.741314] [<ffffffff812f92f3>] ? ___ratelimit+0x93/0x100 [ 788.767018] [<ffffffff81637f49>] skb_warn_bad_offload+0xcd/0xda [ 788.796117] [<ffffffff8152950c>] skb_checksum_help+0x17c/0x190 [ 788.823392] [<ffffffffa01463a1>] netem_enqueue+0x741/0x7c0 [sch_netem] [ 788.854487] [<ffffffff8152cb58>] dev_queue_xmit+0x2a8/0x570 [ 788.880870] [<ffffffff8156ae1d>] ip_finish_output+0x53d/0x7d0 ... The problem occurs because netem is not prepared to handle GSO packets (as it uses skb_checksum_help in its enqueue path, which cannot manipulate these frames). The solution I think is to simply segment the skb in a simmilar fashion to the way we do in __dev_queue_xmit (via validate_xmit_skb), with some minor changes. When we decide to corrupt an skb, if the frame is GSO, we segment it, corrupt the first segment, and enqueue the remaining ones. tested successfully by myself on the latest net kernel, to which this applies Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> CC: Jamal Hadi Salim <jhs@mojatatu.com> CC: "David S. Miller" <davem@davemloft.net> CC: netem@lists.linux-foundation.org CC: eric.dumazet@gmail.com CC: stephen@networkplumber.org Acked-by:
-
WANG Cong authored
[ Upstream commit bdf17661 ] Similarly, we need to update backlog too when we update qlen. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
WANG Cong authored
[ Upstream commit 431e3a8e ] We saw qlen!=0 but backlog==0 on our production machine: qdisc htb 1: dev eth0 root refcnt 2 r2q 10 default 1 direct_packets_stat 0 ver 3.17 Sent 172680457356 bytes 222469449 pkt (dropped 0, overlimits 123575834 requeues 0) backlog 0b 72p requeues 0 The problem is we only count qlen for HTB qdisc but not backlog. We need to update backlog too when we update qlen, so that we can at least know the average packet length. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by:
Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
-
Chris Friesen authored
[ Upstream commit d6d5e999 ] For local routes that require a particular output interface we do not want to cache the result. Caching the result causes incorrect behaviour when there are multiple source addresses on the interface. The end result being that if the intended recipient is waiting on that interface for the packet he won't receive it because it will be delivered on the loopback interface and the IP_PKTINFO ipi_ifindex will be set to the loopback interface as well. This can be tested by running a program such as "dhcp_release" which attempts to inject a packet on a particular interface so that it is received by another program on the same board. The receiving process should see an IP_PKTINFO ipi_ifndex value of the source interface (e.g., eth1) instead of the loopback interface (e.g., lo). The packet will still appear on the loopback interface in tcpdump but the important aspect is that the CMSG info is correct. Sample dhcp_release command line: dhcp_release eth1 192.168.204.222 02:11:33:22:44:66 Signed-off-by:
Allain Legacy <allain.legacy@windriver.com> Signed off-by: Chris Friesen <chris.friesen@windriver.com> Reviewed-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
-
David S. Miller authored
[ Upstream commit a36a0d40 ] In particular, make sure we check for decnet private presence for loopback devices. Signed-off-by:
-
Rasmus Villemoes authored
commit 2aa2f9e2 upstream. On 64 bit, size may very well be huge even if bit 31 happens to be 0. Somehow it doesn't feel right that one can pass a 5 GiB buffer but not a 3 GiB one. So cap at INT_MAX as was probably the intention all along. This is also the made-up value passed by sprintf and vsprintf. Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Hiroshi Shimamoto authored
commit 2541117b upstream. /proc/stats shows invalid gtime when the thread is running in guest. When vtime accounting is not enabled, we cannot get a valid delta. The delta is calculated with now - tsk->vtime_snap, but tsk->vtime_snap is only updated when vtime accounting is runtime enabled. This patch makes task_gtime() just return gtime without computing the buggy non-existing tickless delta when vtime accounting is not enabled. Use context_tracking_is_enabled() to check if vtime is accounting on some cpu, in which case only we need to check the tickless delta. This way we fix the gtime value regression on machines not running nohz full. The kernel config contains CONFIG_VIRT_CPU_ACCOUNTING_GEN=y and CONFIG_NO_HZ_FULL_ALL=n and boot without nohz_full. I ran and stop a busy loop in VM and see the gtime in host. Dump the 43rd field which shows the gtime in every second: # while :; do awk '{print $3" "$43}' /proc/3955/task/4014/stat; sleep 1; done S 4348 R 7064566 R 7064766 R 7064967 R 7065168 S 4759 S 4759 During running busy loop, it returns large value. After applying this patch, we can see right gtime. # while :; do awk '{print $3" "$43}' /proc/10913/task/10956/stat; sleep 1; done S 5338 R 5365 R 5465 R 5566 R 5666 S 5726 S 5726 Signed-off-by:
Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com> Signed-off-by:
Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Chris Metcalf <cmetcalf@ezchip.com> Cc: Christoph Lameter <cl@linux.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luiz Capitulino <lcapitulino@redhat.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1447948054-28668-2-git-send-email-fweisbec@gmail.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
David S. Miller authored
commit 4c03b862 upstream. A nested lock depth was added to the hasbin_delete() code but it doesn't actually work some well and results in tons of lockdep splats. Fix the code instead to properly drop the lock around the operation and just keep peeking the head of the hashbin queue. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Tested-by:
-
Al Viro authored
commit 137d01df upstream. What happens is that a write to /dev/sg is given a request with non-zero ->iovec_count combined with zero ->dxfer_len. Or with ->dxferp pointing to an array full of empty iovecs. Having write permission to /dev/sg shouldn't be equivalent to the ability to trigger BUG_ON() while holding spinlocks... Found by Dmitry Vyukov and syzkaller. [ The BUG_ON() got changed to a WARN_ON_ONCE(), but this fixes the underlying issue. - Linus ] Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Reported-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Sergey Senozhatsky authored
commit fc98c3c8 upstream. Use rcuidle console tracepoint because, apparently, it may be issued from an idle CPU: hw-breakpoint: Failed to enable monitor mode on CPU 0. hw-breakpoint: CPU 0 failed to disable vector catch =============================== [ ERR: suspicious RCU usage. ] 4.10.0-rc8-next-20170215+ #119 Not tainted ------------------------------- ./include/trace/events/printk.h:32 suspicious rcu_dereference_check() usage! other info that might help us debug this: RCU used illegally from idle CPU! rcu_scheduler_active = 2, debug_locks = 0 RCU used illegally from extended quiescent state! 2 locks held by swapper/0/0: #0: (cpu_pm_notifier_lock){......}, at: [<c0237e2c>] cpu_pm_exit+0x10/0x54 #1: (console_lock){+.+.+.}, at: [<c01ab350>] vprintk_emit+0x264/0x474 stack backtrace: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-rc8-next-20170215+ #119 Hardware name: Generic OMAP4 (Flattened Device Tree) console_unlock vprintk_emit vprintk_default printk reset_ctrl_regs dbg_cpu_pm_notify notifier_call_chain cpu_pm_exit omap_enter_idle_coupled cpuidle_enter_state cpuidle_enter_state_coupled do_idle cpu_startup_entry start_kernel This RCU warning, however, is suppressed by lockdep_off() in printk(). lockdep_off() increments the ->lockdep_recursion counter and thus disables RCU_LOCKDEP_WARN() and debug_lockdep_rcu_enabled(), which want lockdep to be enabled "current->lockdep_recursion == 0". Link: http://lkml.kernel.org/r/20170217015932.11898-1-sergey.senozhatsky@gmail.comSigned-off-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Reported-by:
Tony Lindgren <tony@atomide.com> Tested-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Lindgren <tony@atomide.com> Cc: Russell King <rmk@armlinux.org.uk> Signed-off-by:
-
Anoob Soman authored
commit 2bd624b4 upstream. Commit 66644982 ("packet: call fanout_release, while UNREGISTERING a netdev"), unfortunately, introduced the following issues. 1. calling mutex_lock(&fanout_mutex) (fanout_release()) from inside rcu_read-side critical section. rcu_read_lock disables preemption, most often, which prohibits calling sleeping functions. [ ] include/linux/rcupdate.h:560 Illegal context switch in RCU read-side critical section! [ ] [ ] rcu_scheduler_active = 1, debug_locks = 0 [ ] 4 locks held by ovs-vswitchd/1969: [ ] #0: (cb_lock){++++++}, at: [<ffffffff8158a6c9>] genl_rcv+0x19/0x40 [ ] #1: (ovs_mutex){+.+.+.}, at: [<ffffffffa04878ca>] ovs_vport_cmd_del+0x4a/0x100 [openvswitch] [ ] #2: (rtnl_mutex){+.+.+.}, at: [<ffffffff81564157>] rtnl_lock+0x17/0x20 [ ] #3: (rcu_read_lock){......}, at: [<ffffffff81614165>] packet_notifier+0x5/0x3f0 [ ] [ ] Call Trace: [ ] [<ffffffff813770c1>] dump_stack+0x85/0xc4 [ ] [<ffffffff810c9077>] lockdep_rcu_suspicious+0x107/0x110 [ ] [<ffffffff810a2da7>] ___might_sleep+0x57/0x210 [ ] [<ffffffff810a2fd0>] __might_sleep+0x70/0x90 [ ] [<ffffffff8162e80c>] mutex_lock_nested+0x3c/0x3a0 [ ] [<ffffffff810de93f>] ? vprintk_default+0x1f/0x30 [ ] [<ffffffff81186e88>] ? printk+0x4d/0x4f [ ] [<ffffffff816106dd>] fanout_release+0x1d/0xe0 [ ] [<ffffffff81614459>] packet_notifier+0x2f9/0x3f0 2. calling mutex_lock(&fanout_mutex) inside spin_lock(&po->bind_lock). "sleeping function called from invalid context" [ ] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620 [ ] in_atomic(): 1, irqs_disabled(): 0, pid: 1969, name: ovs-vswitchd [ ] INFO: lockdep is turned off. [ ] Call Trace: [ ] [<ffffffff813770c1>] dump_stack+0x85/0xc4 [ ] [<ffffffff810a2f52>] ___might_sleep+0x202/0x210 [ ] [<ffffffff810a2fd0>] __might_sleep+0x70/0x90 [ ] [<ffffffff8162e80c>] mutex_lock_nested+0x3c/0x3a0 [ ] [<ffffffff816106dd>] fanout_release+0x1d/0xe0 [ ] [<ffffffff81614459>] packet_notifier+0x2f9/0x3f0 3. calling dev_remove_pack(&fanout->prot_hook), from inside spin_lock(&po->bind_lock) or rcu_read-side critical-section. dev_remove_pack() -> synchronize_net(), which might sleep. [ ] BUG: scheduling while atomic: ovs-vswitchd/1969/0x00000002 [ ] INFO: lockdep is turned off. [ ] Call Trace: [ ] [<ffffffff813770c1>] dump_stack+0x85/0xc4 [ ] [<ffffffff81186274>] __schedule_bug+0x64/0x73 [ ] [<ffffffff8162b8cb>] __schedule+0x6b/0xd10 [ ] [<ffffffff8162c5db>] schedule+0x6b/0x80 [ ] [<ffffffff81630b1d>] schedule_timeout+0x38d/0x410 [ ] [<ffffffff810ea3fd>] synchronize_sched_expedited+0x53d/0x810 [ ] [<ffffffff810ea6de>] synchronize_rcu_expedited+0xe/0x10 [ ] [<ffffffff8154eab5>] synchronize_net+0x35/0x50 [ ] [<ffffffff8154eae3>] dev_remove_pack+0x13/0x20 [ ] [<ffffffff8161077e>] fanout_release+0xbe/0xe0 [ ] [<ffffffff81614459>] packet_notifier+0x2f9/0x3f0 4. fanout_release() races with calls from different CPU. To fix the above problems, remove the call to fanout_release() under rcu_read_lock(). Instead, call __dev_remove_pack(&fanout->prot_hook) and netdev_run_todo will be happy that &dev->ptype_specific list is empty. In order to achieve this, I moved dev_{add,remove}_pack() out of fanout_{add,release} to __fanout_{link,unlink}. So, call to {,__}unregister_prot_hook() will make sure fanout->prot_hook is removed as well. Fixes: 66644982 ("packet: call fanout_release, while UNREGISTERING a netdev") Reported-by:
Anoob Soman <anoob.soman@citrix.com> Acked-by:
-
Anoob Soman authored
commit 66644982 upstream. If a socket has FANOUT sockopt set, a new proto_hook is registered as part of fanout_add(). When processing a NETDEV_UNREGISTER event in af_packet, __fanout_unlink is called for all sockets, but prot_hook which was registered as part of fanout_add is not removed. Call fanout_release, on a NETDEV_UNREGISTER, which removes prot_hook and removes fanout from the fanout_list. This fixes BUG_ON(!list_empty(&dev->ptype_specific)) in netdev_run_todo() Signed-off-by:
-
Miklos Szeredi authored
commit 5a81e6a1 upstream. Flags (PIPE_BUF_FLAG_PACKET, PIPE_BUF_FLAG_GIFT) could remain on the unused part of the pipe ring buffer. Previously splice_to_pipe() left the flags value alone, which could result in incorrect behavior. Uninitialized flags appears to have been there from the introduction of the splice syscall. Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Anssi Hannula authored
commit acf138f1 upstream. The xilinx_emaclite uses __raw_writel and __raw_readl for register accesses. Those functions do not imply any kind of memory barriers and they may be reordered. The driver does not seem to take that into account, though, and the driver does not satisfy the ordering requirements of the hardware. For clear examples, see xemaclite_mdio_write() and xemaclite_mdio_read() which try to set MDIO address before initiating the transaction. I'm seeing system freezes with the driver with GCC 5.4 and current Linux kernels on Zynq-7000 SoC immediately when trying to use the interface. In commit 123c1407 ("net: emaclite: Do not use microblaze and ppc IO functions") the driver was switched from non-generic in_be32/out_be32 (memory barriers, big endian) to __raw_readl/__raw_writel (no memory barriers, native endian), so apparently the device follows system endianness and the driver was originally written with the assumption of memory barriers. Rather than try to hunt for each case of missing barrier, just switch the driver to use iowrite32/ioread32/iowrite32be/ioread32be depending on endianness instead. Tested on little-endian Zynq-7000 ARM SoC FPGA. Signed-off-by:
Anssi Hannula <anssi.hannula@bitwise.fi> Fixes: 123c1407 ("net: emaclite: Do not use microblaze and ppc IO functions") Signed-off-by:
-
Anssi Hannula authored
commit cd224553 upstream. xilinx_emaclite looks at the received data to try to determine the Ethernet packet length but does not properly clamp it if proto_type == ETH_P_IP or 1500 < proto_type <= 1518, causing a buffer overflow and a panic via skb_panic() as the length exceeds the allocated skb size. Fix those cases. Also add an additional unconditional check with WARN_ON() at the end. Signed-off-by:
-
Mauro Carvalho Chehab authored
commit f9c85ee6 upstream. Reported as a Kaffeine bug: https://bugs.kde.org/show_bug.cgi?id=375811 The USB control messages require DMA to work. We cannot pass a stack-allocated buffer, as it is not warranted that the stack would be into a DMA enabled area. On Kernel 4.9, the default is to not accept DMA on stack anymore on x86 architecture. On other architectures, this has been a requirement since Kernel 2.2. So, after this patch, this driver should likely work fine on all archs. Tested with USB ID 2040:5510: Hauppauge Windham Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Eric Dumazet authored
commit d199fab6 upstream. Multiple threads can call fanout_add() at the same time. We need to grab fanout_mutex earlier to avoid races that could lead to one thread freeing po->rollover that was set by another thread. Do the same in fanout_release(), for peace of mind, and to help us finding lockdep issues earlier. Fixes: dc99f600 ("packet: Add fanout support.") Fixes: 0648ab70 ("packet: rollover prepare: per-socket state") Signed-off-by:
-
Anssi Hannula authored
commit 3d4ef329 upstream. Commit 577fb131 ("mmc: rework selection of bus speed mode") refactored bus width selection code to mmc_select_bus_width(). However, it also altered the behavior to not call the selection code in non-high-speed modes anymore. This causes 1-bit mode to always be used when the high-speed mode is not enabled, even though 4-bit and 8-bit bus are valid bus widths in the backwards-compatibility (legacy) mode as well (see e.g. 5.3.2 Bus Speed Modes in JEDEC 84-B50). This results in a significant regression in transfer speeds. Fix the code to allow 4-bit and 8-bit widths even without high-speed mode, as before. Tested with a Zynq-7000 PicoZed 7020 board. Fixes: 577fb131 ("mmc: rework selection of bus speed mode") Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Yang Yang authored
commit 25f71d1c upstream. The UEVENT user mode helper is enabled before the initcalls are executed and is available when the root filesystem has been mounted. The user mode helper is triggered by device init calls and the executable might use the futex syscall. futex_init() is marked __initcall which maps to device_initcall, but there is no guarantee that futex_init() is invoked _before_ the first device init call which triggers the UEVENT user mode helper. If the user mode helper uses the futex syscall before futex_init() then the syscall crashes with a NULL pointer dereference because the futex subsystem has not been initialized yet. Move futex_init() to core_initcall so futexes are initialized before the root filesystem is mounted and the usermode helper becomes available. [ tglx: Rewrote changelog ] Signed-off-by:
Yang Yang <yang.yang29@zte.com.cn> Cc: jiang.biao2@zte.com.cn Cc: jiang.zhengxiong@zte.com.cn Cc: zhong.weidong@zte.com.cn Cc: deng.huali@zte.com.cn Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1483085875-6130-1-git-send-email-yang.yang29@zte.com.cnSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Eric Dumazet authored
commit 8b74d439 upstream. It seems nobody used LLC since linux-3.12. Fortunately fuzzers like syzkaller still know how to run this code, otherwise it would be no fun. Setting skb->sk without skb->destructor leads to all kinds of bugs, we now prefer to be very strict about it. Ideally here we would use skb_set_owner() but this helper does not exist yet, only CAN seems to have a private helper for that. Fixes: 376c7311 ("net: add a temporary sanity check in skb_orphan()") Signed-off-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
-
Ben Hutchings authored
Extracted from commit 62bccb8c ("net-timestamp: Make the clone operation stand-alone from phy timestamping"). Signed-off-by:
-
Eric Dumazet authored
commit 72fb96e7 upstream. udp_ioctl(), as its name suggests, is used by UDP protocols, but is also used by L2TP :( L2TP should use its own handler, because it really does not look the same. SIOCINQ for instance should not assume UDP checksum or headers. Thanks to Andrey and syzkaller team for providing the report and a nice reproducer. While crashes only happen on recent kernels (after commit 7c13f97f ("udp: do fwd memory scheduling on dequeue")), this probably needs to be backported to older kernels. Fixes: 7c13f97f ("udp: do fwd memory scheduling on dequeue") Fixes: 85584672 ("udp: Fix udp_poll() and ioctl()") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Boris Ostrovsky authored
commit 74470954 upstream. rx_refill_timer should be deleted as soon as we disconnect from the backend since otherwise it is possible for the timer to go off before we get to xennet_destroy_queues(). If this happens we may dereference queue->rx.sring which is set to NULL in xennet_disconnect_backend(). Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
-
Steffen Maier authored
commit 2dfa6688 upstream. Dan Carpenter kindly reported: <quote> The patch d27a7cb9: "zfcp: trace on request for open and close of WKA port" from Aug 10, 2016, leads to the following static checker warning: drivers/s390/scsi/zfcp_fsf.c:1615 zfcp_fsf_open_wka_port() warn: 'req' was already freed. drivers/s390/scsi/zfcp_fsf.c 1609 zfcp_fsf_start_timer(req, ZFCP_FSF_REQUEST_TIMEOUT); 1610 retval = zfcp_fsf_req_send(req); 1611 if (retval) 1612 zfcp_fsf_req_free(req); ^^^ Freed. 1613 out: 1614 spin_unlock_irq(&qdio->req_q_lock); 1615 if (req && !IS_ERR(req)) 1616 zfcp_dbf_rec_run_wka("fsowp_1", wka_port, req->req_id); ^^^^^^^^^^^ Use after free. 1617 return retval; 1618 } Same thing for zfcp_fsf_close_wka_port() as well. </quote> Rather than relying on req being NULL (or ERR_PTR) for all cases where we don't want to trace or should not trace, simply check retval which is unconditionally initialized with -EIO != 0 and it can only become 0 on successful retval = zfcp_fsf_req_send(req). With that we can also remove the then again unnecessary unconditional initialization of req which was introduced with that earlier commit. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Suggested-by:
Benjamin Block <bblock@linux.vnet.ibm.com> Signed-off-by:
Steffen Maier <maier@linux.vnet.ibm.com> Fixes: d27a7cb9 ("zfcp: trace on request for open and close of WKA port") Reviewed-by:
Jens Remus <jremus@linux.vnet.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Hui Wang authored
commit af677166 upstream. Without this change, the HDMI/DP codec will be recognised as a generic codec, and there is no sound when playing through this codec. As suggested by NVidia side, after adding the new ID in the driver, the sound playing works well. Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> [bwh: Backported to 3.16: don't use HDA_CODEC_ENTRY()] Signed-off-by:
-
WANG Cong authored
commit 73d2c667 upstream. Andrey reported a kernel crash: general protection fault: 0000 [#1] SMP KASAN Dumping ftrace buffer: (ftrace buffer empty) Modules linked in: CPU: 2 PID: 3880 Comm: syz-executor1 Not tainted 4.10.0-rc6+ #124 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 task: ffff880060048040 task.stack: ffff880069be8000 RIP: 0010:ping_v4_push_pending_frames net/ipv4/ping.c:647 [inline] RIP: 0010:ping_v4_sendmsg+0x1acd/0x23f0 net/ipv4/ping.c:837 RSP: 0018:ffff880069bef8b8 EFLAGS: 00010206 RAX: dffffc0000000000 RBX: ffff880069befb90 RCX: 0000000000000000 RDX: 0000000000000018 RSI: ffff880069befa30 RDI: 00000000000000c2 RBP: ffff880069befbb8 R08: 0000000000000008 R09: 0000000000000000 R10: 0000000000000002 R11: 0000000000000000 R12: ffff880069befab0 R13: ffff88006c624a80 R14: ffff880069befa70 R15: 0000000000000000 FS: 00007f6f7c716700(0000) GS:ffff88006de00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000004a6f28 CR3: 000000003a134000 CR4: 00000000000006e0 Call Trace: inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:744 sock_sendmsg_nosec net/socket.c:635 [inline] sock_sendmsg+0xca/0x110 net/socket.c:645 SYSC_sendto+0x660/0x810 net/socket.c:1687 SyS_sendto+0x40/0x50 net/socket.c:1655 entry_SYSCALL_64_fastpath+0x1f/0xc2 This is because we miss a check for NULL pointer for skb_peek() when the queue is empty. Other places already have the same check. Fixes: c319b4d7 ("net: ipv4: add IPPROTO_ICMP socket kind") Reported-by:
-
Jeff Mahoney authored
commit 2a362249 upstream. Commit 4c63c245 incorrectly assumed that returning -ENOIOCTLCMD would cause the native ioctl to be called. The ->compat_ioctl callback is expected to handle all ioctls, not just compat variants. As a result, when using 32-bit userspace on 64-bit kernels, everything except those three ioctls would return -ENOTTY. Fixes: 4c63c245 ("btrfs: bugfix: handle FS_IOC32_{GETFLAGS,SETFLAGS,GETVERSION} in btrfs_ioctl") Signed-off-by:
Jeff Mahoney <jeffm@suse.com> Reviewed-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 9b2792c3 upstream. This patch addresses a long standing bug where the commit phase of COMPARE_AND_WRITE would result in a se_cmd->cmd_kref reference leak if se_cmd->scsi_status returned non SAM_STAT_GOOD. This would manifest first as a lost SCSI response, and eventual hung task during fabric driver logout or re-login, as existing shutdown logic waited for the COMPARE_AND_WRITE se_cmd->cmd_kref to reach zero. To address this bug, compare_and_write_post() has been changed to drop the incorrect !cmd->scsi_status conditional that was preventing *post_ret = 1 for being set during non SAM_STAT_GOOD status. This patch has been tested with SAM_STAT_CHECK_CONDITION status from normal target_complete_cmd() callback path, as well as the incoming __target_execute_cmd() submission failure path when se_cmd->execute_cmd() returns non zero status. Reported-by:
Donald White <dew@datera.io> Cc: Donald White <dew@datera.io> Tested-by:
Gary Guo <ghg@datera.io> Cc: Gary Guo <ghg@datera.io> Reviewed-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit c54eeffb upstream. This patch fixes a bug where incoming task management requests can be explicitly aborted during an active LUN_RESET, but who's struct work_struct are canceled in-flight before execution. This occurs when core_tmr_drain_tmr_list() invokes cancel_work_sync() for the incoming se_tmr_req->task_cmd->work, resulting in cmd->work for target_tmr_work() never getting invoked and the aborted TMR waiting indefinately within transport_wait_for_tasks(). To address this case, perform a CMD_T_ABORTED check early in transport_generic_handle_tmr(), and invoke the normal path via transport_cmd_check_stop_to_fabric() to complete any TMR kthreads blocked waiting for CMD_T_STOP in transport_wait_for_tasks(). Also, move the TRANSPORT_ISTATE_PROCESSING assignment earlier into transport_generic_handle_tmr() so the existing check in core_tmr_drain_tmr_list() avoids attempting abort the incoming se_tmr_req->task_cmd->work if it has already been queued into se_device->tmr_wq. Reported-by:
Rob Millner <rlm@daterainc.com> Tested-by:
-
Nicholas Bellinger authored
commit 0583c261 upstream. This patch adds the missing target_complete_cmd() SCSI status parameter change in target_xcopy_do_work(), that was originally missing in commit 926317de. It correctly propigates up the correct SCSI status during EXTENDED_COPY exception cases, instead of always using the hardcoded SAM_STAT_CHECK_CONDITION from original code. This is required for ESX host environments that expect to hit SAM_STAT_RESERVATION_CONFLICT for certain scenarios, and SAM_STAT_CHECK_CONDITION results in non-retriable status for these cases. Reported-by:
Nixon Vincent <nixon.vincent@calsoftinc.com> Tested-by:
-
Takashi Iwai authored
commit 4842e98f upstream. When a sequencer queue is created in snd_seq_queue_alloc(),it adds the new queue element to the public list before referencing it. Thus the queue might be deleted before the call of snd_seq_queue_use(), and it results in the use-after-free error, as spotted by syzkaller. The fix is to reference the queue object at the right time. Reported-by:
-
Andrey Ryabinin authored
commit 5351fbb1 upstream. page_flip_completed() dereferences 'work' variable after executing queue_work(). This is not safe as the 'work' item might be already freed by queued work: BUG: KASAN: use-after-free in page_flip_completed+0x3ff/0x490 at addr ffff8803dc010f90 Call Trace: __asan_report_load8_noabort+0x59/0x80 page_flip_completed+0x3ff/0x490 intel_finish_page_flip_mmio+0xe3/0x130 intel_pipe_handle_vblank+0x2d/0x40 gen8_irq_handler+0x4a7/0xed0 __handle_irq_event_percpu+0xf6/0x860 handle_irq_event_percpu+0x6b/0x160 handle_irq_event+0xc7/0x1b0 handle_edge_irq+0x1f4/0xa50 handle_irq+0x41/0x70 do_IRQ+0x9a/0x200 common_interrupt+0x89/0x89 Freed: kfree+0x113/0x4d0 intel_unpin_work_fn+0x29a/0x3b0 process_one_work+0x79e/0x1b70 worker_thread+0x611/0x1460 kthread+0x241/0x3a0 ret_from_fork+0x27/0x40 Move queue_work() after trace_i915_flip_complete() to fix this. Fixes: e5510fac ("drm/i915: add tracepoints for flip requests & completions") Signed-off-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20170126143211.24013-1-aryabinin@virtuozzo.com (cherry picked from commit 05c41f92) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
