commit 5a81e6a1 upstream.

Flags (PIPE_BUF_FLAG_PACKET, PIPE_BUF_FLAG_GIFT) could remain on the
unused part of the pipe ring buffer.  Previously splice_to_pipe() left
the flags value alone, which could result in incorrect behavior.

Uninitialized flags appears to have been there from the introduction of
the splice syscall.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.16: adjust context, indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit acf138f1 upstream.

The xilinx_emaclite uses __raw_writel and __raw_readl for register
accesses. Those functions do not imply any kind of memory barriers and
they may be reordered.

The driver does not seem to take that into account, though, and the
driver does not satisfy the ordering requirements of the hardware.
For clear examples, see xemaclite_mdio_write() and xemaclite_mdio_read()
which try to set MDIO address before initiating the transaction.

I'm seeing system freezes with the driver with GCC 5.4 and current
Linux kernels on Zynq-7000 SoC immediately when trying to use the
interface.

In commit 123c1407 ("net: emaclite: Do not use microblaze and ppc
IO functions") the driver was switched from non-generic
in_be32/out_be32 (memory barriers, big endian) to
__raw_readl/__raw_writel (no memory barriers, native endian), so
apparently the device follows system endianness and the driver was
originally written with the assumption of memory barriers.

Rather than try to hunt for each case of missing barrier, just switch
the driver to use iowrite32/ioread32/iowrite32be/ioread32be depending
on endianness instead.

Tested on little-endian Zynq-7000 ARM SoC FPGA.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: 123c1407 ("net: emaclite: Do not use microblaze and ppc IO
functions")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit cd224553 upstream.

xilinx_emaclite looks at the received data to try to determine the
Ethernet packet length but does not properly clamp it if
proto_type == ETH_P_IP or 1500 < proto_type <= 1518, causing a buffer
overflow and a panic via skb_panic() as the length exceeds the allocated
skb size.

Fix those cases.

Also add an additional unconditional check with WARN_ON() at the end.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: bb81b2dd ("net: add Xilinx emac lite device driver")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit f9c85ee6 upstream.

Reported as a Kaffeine bug:
	https://bugs.kde.org/show_bug.cgi?id=375811

The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.

On Kernel 4.9, the default is to not accept DMA on stack anymore
on x86 architecture. On other architectures, this has been a
requirement since Kernel 2.2. So, after this patch, this driver
should likely work fine on all archs.

Tested with USB ID 2040:5510: Hauppauge Windham
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit d199fab6 upstream.

Multiple threads can call fanout_add() at the same time.

We need to grab fanout_mutex earlier to avoid races that could
lead to one thread freeing po->rollover that was set by another thread.

Do the same in fanout_release(), for peace of mind, and to help us
finding lockdep issues earlier.

Fixes: dc99f600 ("packet: Add fanout support.")
Fixes: 0648ab70 ("packet: rollover prepare: per-socket state")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16:
 - No rollover queue stats
 - Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 3d4ef329 upstream.

Commit 577fb131 ("mmc: rework selection of bus speed mode")
refactored bus width selection code to mmc_select_bus_width().

However, it also altered the behavior to not call the selection code in
non-high-speed modes anymore.

This causes 1-bit mode to always be used when the high-speed mode is not
enabled, even though 4-bit and 8-bit bus are valid bus widths in the
backwards-compatibility (legacy) mode as well (see e.g. 5.3.2 Bus Speed
Modes in JEDEC 84-B50). This results in a significant regression in
transfer speeds.

Fix the code to allow 4-bit and 8-bit widths even without high-speed
mode, as before.

Tested with a Zynq-7000 PicoZed 7020 board.

Fixes: 577fb131 ("mmc: rework selection of bus speed mode")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 25f71d1c upstream.

The UEVENT user mode helper is enabled before the initcalls are executed
and is available when the root filesystem has been mounted.

The user mode helper is triggered by device init calls and the executable
might use the futex syscall.

futex_init() is marked __initcall which maps to device_initcall, but there
is no guarantee that futex_init() is invoked _before_ the first device init
call which triggers the UEVENT user mode helper.

If the user mode helper uses the futex syscall before futex_init() then the
syscall crashes with a NULL pointer dereference because the futex subsystem
has not been initialized yet.

Move futex_init() to core_initcall so futexes are initialized before the
root filesystem is mounted and the usermode helper becomes available.

[ tglx: Rewrote changelog ]
Signed-off-by: Yang Yang <yang.yang29@zte.com.cn>
Cc: jiang.biao2@zte.com.cn
Cc: jiang.zhengxiong@zte.com.cn
Cc: zhong.weidong@zte.com.cn
Cc: deng.huali@zte.com.cn
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1483085875-6130-1-git-send-email-yang.yang29@zte.com.cnSigned-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 8b74d439 upstream.

It seems nobody used LLC since linux-3.12.

Fortunately fuzzers like syzkaller still know how to run this code,
otherwise it would be no fun.

Setting skb->sk without skb->destructor leads to all kinds of
bugs, we now prefer to be very strict about it.

Ideally here we would use skb_set_owner() but this helper does not exist yet,
only CAN seems to have a private helper for that.

Fixes: 376c7311 ("net: add a temporary sanity check in skb_orphan()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

Extracted from commit 62bccb8c ("net-timestamp: Make the clone operation
stand-alone from phy timestamping").
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 72fb96e7 upstream.

udp_ioctl(), as its name suggests, is used by UDP protocols,
but is also used by L2TP :(

L2TP should use its own handler, because it really does not
look the same.

SIOCINQ for instance should not assume UDP checksum or headers.

Thanks to Andrey and syzkaller team for providing the report
and a nice reproducer.

While crashes only happen on recent kernels (after commit
7c13f97f ("udp: do fwd memory scheduling on dequeue")), this
probably needs to be backported to older kernels.

Fixes: 7c13f97f ("udp: do fwd memory scheduling on dequeue")
Fixes: 85584672 ("udp: Fix udp_poll() and ioctl()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 74470954 upstream.

rx_refill_timer should be deleted as soon as we disconnect from the
backend since otherwise it is possible for the timer to go off before
we get to xennet_destroy_queues(). If this happens we may dereference
queue->rx.sring which is set to NULL in xennet_disconnect_backend().
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: del_timer_sync() was called from xennet_remove()
 but that's also too late]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 2dfa6688 upstream.

Dan Carpenter kindly reported:
<quote>
The patch d27a7cb9: "zfcp: trace on request for open and close of
WKA port" from Aug 10, 2016, leads to the following static checker
warning:

	drivers/s390/scsi/zfcp_fsf.c:1615 zfcp_fsf_open_wka_port()
	warn: 'req' was already freed.

drivers/s390/scsi/zfcp_fsf.c
  1609          zfcp_fsf_start_timer(req, ZFCP_FSF_REQUEST_TIMEOUT);
  1610          retval = zfcp_fsf_req_send(req);
  1611          if (retval)
  1612                  zfcp_fsf_req_free(req);
                                          ^^^
Freed.

  1613  out:
  1614          spin_unlock_irq(&qdio->req_q_lock);
  1615          if (req && !IS_ERR(req))
  1616                  zfcp_dbf_rec_run_wka("fsowp_1", wka_port, req->req_id);
                                                                  ^^^^^^^^^^^
Use after free.

  1617          return retval;
  1618  }

Same thing for zfcp_fsf_close_wka_port() as well.
</quote>

Rather than relying on req being NULL (or ERR_PTR) for all cases where
we don't want to trace or should not trace,
simply check retval which is unconditionally initialized with -EIO != 0
and it can only become 0 on successful retval = zfcp_fsf_req_send(req).
With that we can also remove the then again unnecessary unconditional
initialization of req which was introduced with that earlier commit.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: d27a7cb9 ("zfcp: trace on request for open and close of WKA port")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit af677166 upstream.

Without this change, the HDMI/DP codec will be recognised as a
generic codec, and there is no sound when playing through this codec.

As suggested by NVidia side, after adding the new ID in the driver,
the sound playing works well.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.16: don't use HDA_CODEC_ENTRY()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 73d2c667 upstream.

Andrey reported a kernel crash:

  general protection fault: 0000 [#1] SMP KASAN
  Dumping ftrace buffer:
     (ftrace buffer empty)
  Modules linked in:
  CPU: 2 PID: 3880 Comm: syz-executor1 Not tainted 4.10.0-rc6+ #124
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
  task: ffff880060048040 task.stack: ffff880069be8000
  RIP: 0010:ping_v4_push_pending_frames net/ipv4/ping.c:647 [inline]
  RIP: 0010:ping_v4_sendmsg+0x1acd/0x23f0 net/ipv4/ping.c:837
  RSP: 0018:ffff880069bef8b8 EFLAGS: 00010206
  RAX: dffffc0000000000 RBX: ffff880069befb90 RCX: 0000000000000000
  RDX: 0000000000000018 RSI: ffff880069befa30 RDI: 00000000000000c2
  RBP: ffff880069befbb8 R08: 0000000000000008 R09: 0000000000000000
  R10: 0000000000000002 R11: 0000000000000000 R12: ffff880069befab0
  R13: ffff88006c624a80 R14: ffff880069befa70 R15: 0000000000000000
  FS:  00007f6f7c716700(0000) GS:ffff88006de00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00000000004a6f28 CR3: 000000003a134000 CR4: 00000000000006e0
  Call Trace:
   inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:744
   sock_sendmsg_nosec net/socket.c:635 [inline]
   sock_sendmsg+0xca/0x110 net/socket.c:645
   SYSC_sendto+0x660/0x810 net/socket.c:1687
   SyS_sendto+0x40/0x50 net/socket.c:1655
   entry_SYSCALL_64_fastpath+0x1f/0xc2

This is because we miss a check for NULL pointer for skb_peek() when
the queue is empty. Other places already have the same check.

Fixes: c319b4d7 ("net: ipv4: add IPPROTO_ICMP socket kind")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 2a362249 upstream.

Commit 4c63c245 incorrectly assumed that returning -ENOIOCTLCMD would
cause the native ioctl to be called.  The ->compat_ioctl callback is
expected to handle all ioctls, not just compat variants.  As a result,
when using 32-bit userspace on 64-bit kernels, everything except those
three ioctls would return -ENOTTY.

Fixes: 4c63c245 ("btrfs: bugfix: handle FS_IOC32_{GETFLAGS,SETFLAGS,GETVERSION} in btrfs_ioctl")
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 9b2792c3 upstream.

This patch addresses a long standing bug where the commit phase
of COMPARE_AND_WRITE would result in a se_cmd->cmd_kref reference
leak if se_cmd->scsi_status returned non SAM_STAT_GOOD.

This would manifest first as a lost SCSI response, and eventual
hung task during fabric driver logout or re-login, as existing
shutdown logic waited for the COMPARE_AND_WRITE se_cmd->cmd_kref
to reach zero.

To address this bug, compare_and_write_post() has been changed
to drop the incorrect !cmd->scsi_status conditional that was
preventing *post_ret = 1 for being set during non SAM_STAT_GOOD
status.

This patch has been tested with SAM_STAT_CHECK_CONDITION status
from normal target_complete_cmd() callback path, as well as the
incoming __target_execute_cmd() submission failure path when
se_cmd->execute_cmd() returns non zero status.
Reported-by: Donald White <dew@datera.io>
Cc: Donald White <dew@datera.io>
Tested-by: Gary Guo <ghg@datera.io>
Cc: Gary Guo <ghg@datera.io>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit c54eeffb upstream.

This patch fixes a bug where incoming task management requests
can be explicitly aborted during an active LUN_RESET, but who's
struct work_struct are canceled in-flight before execution.

This occurs when core_tmr_drain_tmr_list() invokes cancel_work_sync()
for the incoming se_tmr_req->task_cmd->work, resulting in cmd->work
for target_tmr_work() never getting invoked and the aborted TMR
waiting indefinately within transport_wait_for_tasks().

To address this case, perform a CMD_T_ABORTED check early in
transport_generic_handle_tmr(), and invoke the normal path via
transport_cmd_check_stop_to_fabric() to complete any TMR kthreads
blocked waiting for CMD_T_STOP in transport_wait_for_tasks().

Also, move the TRANSPORT_ISTATE_PROCESSING assignment earlier
into transport_generic_handle_tmr() so the existing check in
core_tmr_drain_tmr_list() avoids attempting abort the incoming
se_tmr_req->task_cmd->work if it has already been queued into
se_device->tmr_wq.
Reported-by: Rob Millner <rlm@daterainc.com>
Tested-by: Rob Millner <rlm@daterainc.com>
Cc: Rob Millner <rlm@daterainc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[bwh: Backported to 3.16:
 - Tags are 32-bit; print them with %u
 - Command tag must be looked up with get_task_tag op]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 0583c261 upstream.

This patch adds the missing target_complete_cmd() SCSI status
parameter change in target_xcopy_do_work(), that was originally
missing in commit 926317de.

It correctly propigates up the correct SCSI status during
EXTENDED_COPY exception cases, instead of always using the
hardcoded SAM_STAT_CHECK_CONDITION from original code.

This is required for ESX host environments that expect to
hit SAM_STAT_RESERVATION_CONFLICT for certain scenarios,
and SAM_STAT_CHECK_CONDITION results in non-retriable
status for these cases.
Reported-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Tested-by: Nixon Vincent <nixon.vincent@calsoftinc.com>
Cc: Nixon Vincent <nixon.vincent@calsoftinc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 4842e98f upstream.

When a sequencer queue is created in snd_seq_queue_alloc(),it adds the
new queue element to the public list before referencing it.  Thus the
queue might be deleted before the call of snd_seq_queue_use(), and it
results in the use-after-free error, as spotted by syzkaller.

The fix is to reference the queue object at the right time.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 5351fbb1 upstream.

page_flip_completed() dereferences 'work' variable after executing
queue_work(). This is not safe as the 'work' item might be already freed
by queued work:

    BUG: KASAN: use-after-free in page_flip_completed+0x3ff/0x490 at addr ffff8803dc010f90
    Call Trace:
     __asan_report_load8_noabort+0x59/0x80
     page_flip_completed+0x3ff/0x490
     intel_finish_page_flip_mmio+0xe3/0x130
     intel_pipe_handle_vblank+0x2d/0x40
     gen8_irq_handler+0x4a7/0xed0
     __handle_irq_event_percpu+0xf6/0x860
     handle_irq_event_percpu+0x6b/0x160
     handle_irq_event+0xc7/0x1b0
     handle_edge_irq+0x1f4/0xa50
     handle_irq+0x41/0x70
     do_IRQ+0x9a/0x200
     common_interrupt+0x89/0x89

    Freed:
     kfree+0x113/0x4d0
     intel_unpin_work_fn+0x29a/0x3b0
     process_one_work+0x79e/0x1b70
     worker_thread+0x611/0x1460
     kthread+0x241/0x3a0
     ret_from_fork+0x27/0x40

Move queue_work() after	trace_i915_flip_complete() to fix this.

Fixes: e5510fac ("drm/i915: add tracepoints for flip requests & completions")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126143211.24013-1-aryabinin@virtuozzo.com
(cherry picked from commit 05c41f92)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit a524c218 upstream.
Reported-by: Jo-Philipp Wich <jo@mein.io>
Fixes: 9aed02fe ("ARC: [arcompact] handle unaligned access delay slot")
Cc: linux-kernel@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 2d6a0e9d upstream.

Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit d4114914 upstream.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 7926aff5 upstream.

Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 5593523f upstream.

Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
References: https://bugs.debian.org/852556Reported-by: Lisandro Damián Nicanor Pérez Meyer <lisandro@debian.org>
Tested-by: Lisandro Damián Nicanor Pérez Meyer <lisandro@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 37a7ea4a upstream.

snd_seq_pool_done() syncs with closing of all opened threads, but it
aborts the wait loop with a timeout, and proceeds to the release
resource even if not all threads have been closed.  The timeout was 5
seconds, and if you run a crazy stuff, it can exceed easily, and may
result in the access of the invalid memory address -- this is what
syzkaller detected in a bug report.

As a fix, let the code graduate from naiveness, simply remove the loop
timeout.

BugLink: http://lkml.kernel.org/r/CACT4Y+YdhDV2H5LLzDTJDVF-qiYHUHhtRaW4rbb4gUhTCQB81w@mail.gmail.comReported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit da7061c8 upstream.

The function ieee80211_ie_split_vendor doesn't return 0 on errors. Instead
it returns any offset < ielen when WLAN_EID_VENDOR_SPECIFIC is found. The
return value in mesh_add_vendor_ies must therefore be checked against
ifmsh->ie_len and not 0. Otherwise all ifmsh->ie starting with
WLAN_EID_VENDOR_SPECIFIC will be rejected.

Fixes: 082ebb0c ("mac80211: fix mesh beacon format")
Signed-off-by: Thorsten Horstmann <thorsten@defutech.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[sven@narfation.org: Add commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit d71b7896 upstream.

syzkaller found another out of bound access in ip_options_compile(),
or more exactly in cipso_v4_validate()

Fixes: 20e2a864 ("cipso: handle CIPSO options correctly when NetLabel is disabled")
Fixes: 446fda4f ("[NetLabel]: CIPSOv4 engine")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov  <dvyukov@google.com>
Cc: Paul Moore <paul@paul-moore.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 5abf186a upstream.

do_generic_file_read() can be told to perform a large request from
userspace.  If the system is under OOM and the reading task is the OOM
victim then it has an access to memory reserves and finishing the full
request can lead to the full memory depletion which is dangerous.  Make
sure we rather go with a short read and allow the killed task to
terminate.

Link: http://lkml.kernel.org/r/20170201092706.9966-3-mhocko@kernel.orgSigned-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 5fa8bbda upstream.

Dmitry reported a warning [1] showing that we were calling
net_disable_timestamp() -> static_key_slow_dec() from a non
process context.

Grabbing a mutex while holding a spinlock or rcu_read_lock()
is not allowed.

As Cong suggested, we now use a work queue.

It is possible netstamp_clear() exits while netstamp_needed_deferred
is not zero, but it is probably not worth trying to do better than that.

netstamp_needed_deferred atomic tracks the exact number of deferred
decrements.

[1]
[ INFO: suspicious RCU usage. ]
4.10.0-rc5+ #192 Not tainted
-------------------------------
./include/linux/rcupdate.h:561 Illegal context switch in RCU read-side
critical section!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 0
2 locks held by syz-executor14/23111:
 #0:  (sk_lock-AF_INET6){+.+.+.}, at: [<ffffffff83a35c35>] lock_sock
include/net/sock.h:1454 [inline]
 #0:  (sk_lock-AF_INET6){+.+.+.}, at: [<ffffffff83a35c35>]
rawv6_sendmsg+0x1e65/0x3ec0 net/ipv6/raw.c:919
 #1:  (rcu_read_lock){......}, at: [<ffffffff83ae2678>] nf_hook
include/linux/netfilter.h:201 [inline]
 #1:  (rcu_read_lock){......}, at: [<ffffffff83ae2678>]
__ip6_local_out+0x258/0x840 net/ipv6/output_core.c:160

stack backtrace:
CPU: 2 PID: 23111 Comm: syz-executor14 Not tainted 4.10.0-rc5+ #192
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs
01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:15 [inline]
 dump_stack+0x2ee/0x3ef lib/dump_stack.c:51
 lockdep_rcu_suspicious+0x139/0x180 kernel/locking/lockdep.c:4452
 rcu_preempt_sleep_check include/linux/rcupdate.h:560 [inline]
 ___might_sleep+0x560/0x650 kernel/sched/core.c:7748
 __might_sleep+0x95/0x1a0 kernel/sched/core.c:7739
 mutex_lock_nested+0x24f/0x1730 kernel/locking/mutex.c:752
 atomic_dec_and_mutex_lock+0x119/0x160 kernel/locking/mutex.c:1060
 __static_key_slow_dec+0x7a/0x1e0 kernel/jump_label.c:149
 static_key_slow_dec+0x51/0x90 kernel/jump_label.c:174
 net_disable_timestamp+0x3b/0x50 net/core/dev.c:1728
 sock_disable_timestamp+0x98/0xc0 net/core/sock.c:403
 __sk_destruct+0x27d/0x6b0 net/core/sock.c:1441
 sk_destruct+0x47/0x80 net/core/sock.c:1460
 __sk_free+0x57/0x230 net/core/sock.c:1468
 sock_wfree+0xae/0x120 net/core/sock.c:1645
 skb_release_head_state+0xfc/0x200 net/core/skbuff.c:655
 skb_release_all+0x15/0x60 net/core/skbuff.c:668
 __kfree_skb+0x15/0x20 net/core/skbuff.c:684
 kfree_skb+0x16e/0x4c0 net/core/skbuff.c:705
 inet_frag_destroy+0x121/0x290 net/ipv4/inet_fragment.c:304
 inet_frag_put include/net/inet_frag.h:133 [inline]
 nf_ct_frag6_gather+0x1106/0x3840
net/ipv6/netfilter/nf_conntrack_reasm.c:617
 ipv6_defrag+0x1be/0x2b0 net/ipv6/netfilter/nf_defrag_ipv6_hooks.c:68
 nf_hook_entry_hookfn include/linux/netfilter.h:102 [inline]
 nf_hook_slow+0xc3/0x290 net/netfilter/core.c:310
 nf_hook include/linux/netfilter.h:212 [inline]
 __ip6_local_out+0x489/0x840 net/ipv6/output_core.c:160
 ip6_local_out+0x2d/0x170 net/ipv6/output_core.c:170
 ip6_send_skb+0xa1/0x340 net/ipv6/ip6_output.c:1722
 ip6_push_pending_frames+0xb3/0xe0 net/ipv6/ip6_output.c:1742
 rawv6_push_pending_frames net/ipv6/raw.c:613 [inline]
 rawv6_sendmsg+0x2d1a/0x3ec0 net/ipv6/raw.c:927
 inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:744
 sock_sendmsg_nosec net/socket.c:635 [inline]
 sock_sendmsg+0xca/0x110 net/socket.c:645
 sock_write_iter+0x326/0x600 net/socket.c:848
 do_iter_readv_writev+0x2e3/0x5b0 fs/read_write.c:695
 do_readv_writev+0x42c/0x9b0 fs/read_write.c:872
 vfs_writev+0x87/0xc0 fs/read_write.c:911
 do_writev+0x110/0x2c0 fs/read_write.c:944
 SYSC_writev fs/read_write.c:1017 [inline]
 SyS_writev+0x27/0x30 fs/read_write.c:1014
 entry_SYSCALL_64_fastpath+0x1f/0xc2
RIP: 0033:0x445559
RSP: 002b:00007f6f46fceb58 EFLAGS: 00000292 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 0000000000445559
RDX: 0000000000000001 RSI: 0000000020f1eff0 RDI: 0000000000000005
RBP: 00000000006e19c0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000292 R12: 0000000000700000
R13: 0000000020f59000 R14: 0000000000000015 R15: 0000000000020400
BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:752
in_atomic(): 1, irqs_disabled(): 0, pid: 23111, name: syz-executor14
INFO: lockdep is turned off.
CPU: 2 PID: 23111 Comm: syz-executor14 Not tainted 4.10.0-rc5+ #192
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs
01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:15 [inline]
 dump_stack+0x2ee/0x3ef lib/dump_stack.c:51
 ___might_sleep+0x47e/0x650 kernel/sched/core.c:7780
 __might_sleep+0x95/0x1a0 kernel/sched/core.c:7739
 mutex_lock_nested+0x24f/0x1730 kernel/locking/mutex.c:752
 atomic_dec_and_mutex_lock+0x119/0x160 kernel/locking/mutex.c:1060
 __static_key_slow_dec+0x7a/0x1e0 kernel/jump_label.c:149
 static_key_slow_dec+0x51/0x90 kernel/jump_label.c:174
 net_disable_timestamp+0x3b/0x50 net/core/dev.c:1728
 sock_disable_timestamp+0x98/0xc0 net/core/sock.c:403
 __sk_destruct+0x27d/0x6b0 net/core/sock.c:1441
 sk_destruct+0x47/0x80 net/core/sock.c:1460
 __sk_free+0x57/0x230 net/core/sock.c:1468
 sock_wfree+0xae/0x120 net/core/sock.c:1645
 skb_release_head_state+0xfc/0x200 net/core/skbuff.c:655
 skb_release_all+0x15/0x60 net/core/skbuff.c:668
 __kfree_skb+0x15/0x20 net/core/skbuff.c:684
 kfree_skb+0x16e/0x4c0 net/core/skbuff.c:705
 inet_frag_destroy+0x121/0x290 net/ipv4/inet_fragment.c:304
 inet_frag_put include/net/inet_frag.h:133 [inline]
 nf_ct_frag6_gather+0x1106/0x3840
net/ipv6/netfilter/nf_conntrack_reasm.c:617
 ipv6_defrag+0x1be/0x2b0 net/ipv6/netfilter/nf_defrag_ipv6_hooks.c:68
 nf_hook_entry_hookfn include/linux/netfilter.h:102 [inline]
 nf_hook_slow+0xc3/0x290 net/netfilter/core.c:310
 nf_hook include/linux/netfilter.h:212 [inline]
 __ip6_local_out+0x489/0x840 net/ipv6/output_core.c:160
 ip6_local_out+0x2d/0x170 net/ipv6/output_core.c:170
 ip6_send_skb+0xa1/0x340 net/ipv6/ip6_output.c:1722
 ip6_push_pending_frames+0xb3/0xe0 net/ipv6/ip6_output.c:1742
 rawv6_push_pending_frames net/ipv6/raw.c:613 [inline]
 rawv6_sendmsg+0x2d1a/0x3ec0 net/ipv6/raw.c:927
 inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:744
 sock_sendmsg_nosec net/socket.c:635 [inline]
 sock_sendmsg+0xca/0x110 net/socket.c:645
 sock_write_iter+0x326/0x600 net/socket.c:848
 do_iter_readv_writev+0x2e3/0x5b0 fs/read_write.c:695
 do_readv_writev+0x42c/0x9b0 fs/read_write.c:872
 vfs_writev+0x87/0xc0 fs/read_write.c:911
 do_writev+0x110/0x2c0 fs/read_write.c:944
 SYSC_writev fs/read_write.c:1017 [inline]
 SyS_writev+0x27/0x30 fs/read_write.c:1014
 entry_SYSCALL_64_fastpath+0x1f/0xc2
RIP: 0033:0x445559

Fixes: b90e5794 ("net: dont call jump_label_dec from irq context")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 034dd34f upstream.

Olga Kornievskaia says: "I ran into this oops in the nfsd (below)
(4.10-rc3 kernel). To trigger this I had a client (unsuccessfully) try
to mount the server with krb5 where the server doesn't have the
rpcsec_gss_krb5 module built."

The problem is that rsci.cred is copied from a svc_cred structure that
gss_proxy didn't properly initialize.  Fix that.

[120408.542387] general protection fault: 0000 [#1] SMP
...
[120408.565724] CPU: 0 PID: 3601 Comm: nfsd Not tainted 4.10.0-rc3+ #16
[120408.567037] Hardware name: VMware, Inc. VMware Virtual =
Platform/440BX Desktop Reference Platform, BIOS 6.00 07/02/2015
[120408.569225] task: ffff8800776f95c0 task.stack: ffffc90003d58000
[120408.570483] RIP: 0010:gss_mech_put+0xb/0x20 [auth_rpcgss]
...
[120408.584946]  ? rsc_free+0x55/0x90 [auth_rpcgss]
[120408.585901]  gss_proxy_save_rsc+0xb2/0x2a0 [auth_rpcgss]
[120408.587017]  svcauth_gss_proxy_init+0x3cc/0x520 [auth_rpcgss]
[120408.588257]  ? __enqueue_entity+0x6c/0x70
[120408.589101]  svcauth_gss_accept+0x391/0xb90 [auth_rpcgss]
[120408.590212]  ? try_to_wake_up+0x4a/0x360
[120408.591036]  ? wake_up_process+0x15/0x20
[120408.592093]  ? svc_xprt_do_enqueue+0x12e/0x2d0 [sunrpc]
[120408.593177]  svc_authenticate+0xe1/0x100 [sunrpc]
[120408.594168]  svc_process_common+0x203/0x710 [sunrpc]
[120408.595220]  svc_process+0x105/0x1c0 [sunrpc]
[120408.596278]  nfsd+0xe9/0x160 [nfsd]
[120408.597060]  kthread+0x101/0x140
[120408.597734]  ? nfsd_destroy+0x60/0x60 [nfsd]
[120408.598626]  ? kthread_park+0x90/0x90
[120408.599448]  ret_from_fork+0x22/0x30

Fixes: 1d658336 "SUNRPC: Add RPC based upcall mechanism for RPCGSS auth"
Cc: Simo Sorce <simo@redhat.com>
Reported-by: Olga Kornievskaia <kolga@netapp.com>
Tested-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit d07830db upstream.

Seems that ATEN serial-to-usb devices using pl2303 exist with
different device ids. This patch adds a missing device ID so it
is recognised by the driver.
Signed-off-by: Marcel J.E. Mol <marcel@mesa.nl>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 161e6d44 upstream.

One of our kernelCI boxes hanged at boot because a faulty eSDHC device
was triggering spurious CARD_INT interrupts for SD cards, causing CMD52
reads, which are not allowed for SD devices.  This adds a sanity check
to the interruption path, preventing that illegal command from getting
sent if the CARD_INT interruption should be disabled.

This quirk allows that particular machine to resume boot despite the
faulty hardware, instead of getting hung dealing with thousands of
mishandled interrupts.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 24bf7ae3 upstream.

Based on the xf86-video-nv code, NFORCE (NV1A) and NFORCE2 (NV1F) have a
different way of retrieving clocks. See the
nv_hw.c:nForceUpdateArbitrationSettings function in the original code
for how these clocks were accessed.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54587Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 228dbbfb upstream.

Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.

Fixes: 5be6f62b ("ARM: 6883/1: ptrace: Migrate to regsets framework")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 0b3589be upstream.

Andres reported that MMAP2 records for anonymous memory always have
their protection field 0.

Turns out, someone daft put the prot/flags generation code in the file
branch, leaving them unset for anonymous memory.
Reported-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Don Zickus <dzickus@redhat.com
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@gmail.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: anton@ozlabs.org
Cc: namhyung@kernel.org
Fixes: f972eb63 ("perf: Pass protection and flags bits through mmap2 interface")
Link: http://lkml.kernel.org/r/20170126221508.GF6536@twins.programming.kicks-ass.netSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit a06393ed upstream.

When removing a bcm tx operation either a hrtimer or a tasklet might run.
As the hrtimer triggers its associated tasklet and vice versa we need to
take care to mutually terminate both handlers.
Reported-by: Michael Josenhans <michael.josenhans@web.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Michael Josenhans <michael.josenhans@web.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 2ad5d52d upstream.

In swab.h the "#if BITS_PER_LONG > 32" breaks compiling userspace programs if
BITS_PER_LONG is #defined by userspace with the sizeof() compiler builtin.

Solve this problem by using __BITS_PER_LONG instead.  Since we now
#include asm/bitsperlong.h avoid further potential userspace pollution
by moving the #define of SHIFT_PER_LONG to bitops.h which is not
exported to userspace.

This patch unbreaks compiling qemu on hppa/parisc.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 9aed02fe upstream.

After emulating an unaligned access in delay slot of a branch, we
pretend as the delay slot never happened - so return back to actual
branch target (or next PC if branch was not taken).

Curently we did this by handling STATUS32.DE, we also need to clear the
BTA.T bit, which is disregarded when returning from original misaligned
exception, but could cause weirdness if it took the interrupt return
path (in case interrupt was acive too)

One ARC700 customer ran into this when enabling unaligned access fixup
for kernel mode accesses as well
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 950eabbd upstream.

With some gcc versions, we get a warning about the eicon driver,
and that currently shows up as the only remaining warning in one
of the build bots:

In file included from ../drivers/isdn/hardware/eicon/message.c:30:0:
eicon/message.c: In function 'mixer_notify_update':
eicon/platform.h:333:18: warning: array subscript is above array bounds [-Warray-bounds]

The code is easily changed to open-code the unusual PUT_WORD() line
causing this to avoid the warning.

Link: http://arm-soc.lixom.net/buildlogs/stable-rc/v4.4.45/Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>