- 24 Feb, 2020 40 commits
-
-
Vladimir Oltean authored
This patch adds the required documentation for the embedded L2 switch inside the NXP LS1028A chip. I've submitted it in the legacy format instead of yaml schema, because DSA itself has not yet been converted to yaml, and this driver defines no custom bindings. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
phy-mode = "gmii" is confusing because it may mean that the port supports the 8-bit-wide parallel data interface pinout, which it doesn't. It may also be confusing because one of the "gmii" internal ports is actually overclocked to run at 2.5Gbps (even though, yes, as far as the switch MAC is concerned, it still thinks it's gigabit). So use the phy-mode = "internal" property to describe the internal ports inside the NXP LS1028A chip (the ones facing the ENETC). The change should be fine, because the device tree bindings document is yet to be introduced, and there are no stable DT blobs in use. Signed-off-by:
Michael Walle <michael@walle.cc> Signed-off-by:
-
David S. Miller authored
drivers/net/bareudp.c: In function 'bareudp_xmit_skb': drivers/net/bareudp.c:346:9: warning: 'err' may be used uninitialized in this function [-Wmaybe-uninitialized] 346 | return err; | ^~~ drivers/net/bareudp.c: In function 'bareudp6_xmit_skb': drivers/net/bareudp.c:407:9: warning: 'err' may be used uninitialized in this function [-Wmaybe-uninitialized] 407 | return err; Reported-by:Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
David S. Miller authored
Martin Varghese says: ==================== Bare UDP L3 Encapsulation Module There are various L3 encapsulation standards using UDP being discussed to leverage the UDP based load balancing capability of different networks. MPLSoUDP (__ https://tools.ietf.org/html/rfc7510) is one among them. The Bareudp tunnel module provides a generic L3 encapsulation tunnelling support for tunnelling different L3 protocols like MPLS, IP, NSH etc. inside a UDP tunnel. Special Handling ---------------- The bareudp device supports special handling for MPLS & IP as they can have multiple ethertypes. MPLS procotcol can have ethertypes ETH_P_MPLS_UC (unicast) & ETH_P_MPLS_MC (multicast). IP protocol can have ethertypes ETH_P_IP (v4) & ETH_P_IPV6 (v6). This special handling can be enabled only for ethertypes ETH_P_IP & ETH_P_MPLS_UC with a flag called multiproto mode. Usage ------ 1) Device creation & deletion a) ip link add dev bareudp0 type bareudp dstport 6635 ethertype 0x8847. This creates a bareudp tunnel device which tunnels L3 traffic with ethertype 0x8847 (MPLS traffic). The destination port of the UDP header will be set to 6635.The device will listen on UDP port 6635 to receive traffic. b) ip link delete bareudp0 2) Device creation with multiple proto mode enabled There are two ways to create a bareudp device for MPLS & IP with multiproto mode enabled. a) ip link add dev bareudp0 type bareudp dstport 6635 ethertype 0x8847 multiproto b) ip link add dev bareudp0 type bareudp dstport 6635 ethertype mpls 3) Device Usage The bareudp device could be used along with OVS or flower filter in TC. The OVS or TC flower layer must set the tunnel information in SKB dst field before sending packet buffer to the bareudp device for transmission. On reception the bareudp device extracts and stores the tunnel information in SKB dst field before passing the packet buffer to the network stack. Why not FOU ? ------------ FOU by design does l4 encapsulation.It maps udp port to ipproto (IP protocol number for l4 protocol). Bareudp acheives a generic l3 encapsulation.It maps udp port to l3 ethertype. ==================== Signed-off-by:
-
Martin Varghese authored
Special handling is needed in bareudp module for IP & MPLS as they support more than one ethertypes. MPLS has 2 ethertypes. 0x8847 for MPLS unicast and 0x8848 for MPLS multicast. While decapsulating MPLS packet from UDP packet the tunnel destination IP address is checked to determine the ethertype. The ethertype of the packet will be set to 0x8848 if the tunnel destination IP address is a multicast IP address. The ethertype of the packet will be set to 0x8847 if the tunnel destination IP address is a unicast IP address. IP has 2 ethertypes.0x0800 for IPV4 and 0x86dd for IPv6. The version field of the IP header tunnelled will be checked to determine the ethertype. This special handling to tunnel additional ethertypes will be disabled by default and can be enabled using a flag called multiproto. This flag can be used only with ethertypes 0x8847 and 0x0800. Signed-off-by:
Martin Varghese <martin.varghese@nokia.com> Acked-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Martin Varghese authored
The Bareudp tunnel module provides a generic L3 encapsulation tunnelling module for tunnelling different protocols like MPLS, IP,NSH etc inside a UDP tunnel. Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning unix_wait_for_peer() warning: context imbalance in unix_wait_for_peer() - unexpected unlock The root cause is the missing annotation at unix_wait_for_peer() Add the missing annotation __releases(&unix_sk(other)->lock) Signed-off-by:
Jules Irenge <jbi.octave@gmail.com> Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning at dccp_child_process() warning: context imbalance in dccp_child_process() - unexpected unlock The root cause is the missing annotation at dccp_child_process() Add the missing __releases(child) annotation Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning at nr_neigh_stop() warning: context imbalance in nr_neigh_stop() - unexpected unlock The root cause is the missing annotation at nr_neigh_stop() Add the missing __releases(&nr_neigh_list_lock) annotation Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning at nr_neigh_start() warning: context imbalance in nr_neigh_start() - wrong count at exit The root cause is the missing annotation at nr_neigh_start() Add the missing __acquires(&nr_neigh_list_lock) annotation Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning at nr_node_stop() warning: context imbalance in nr_node_stop() - wrong count at exit The root cause is the missing annotation at nr_node_stop() Add the missing __releases(&nr_node_list_lock) annotation Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning at nr_node_start() warning: context imbalance in nr_node_start() - wrong count at exit The root cause is the missing annotation at nr_node_start() Add the missing __acquires(&nr_node_list_lock) annotation Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning at nr_info_stop() warning: context imbalance in nr_info_stop() - unexpected unlock The root cause is the missing annotation at nr_info_stop() Add the missing __releases(&nr_list_lock) Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning at nr_info_start() warning: context imbalance in nr_info_start() - wrong count at exit The root cause is the missing annotation at nr_info_start() Add the missing __acquires(&nr_list_lock) Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning at llc_seq_start() warning: context imbalance in llc_seq_start() - wrong count at exit The root cause is the msiing annotation at llc_seq_start() Add the missing __acquires(RCU) annotation Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning at sctp_transport_walk_stop() warning: context imbalance in sctp_transport_walk_stop - wrong count at exit The root cause is the missing annotation at sctp_transport_walk_stop() Add the missing __releases(RCU) annotation Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning at sctp_transport_walk_start() warning: context imbalance in sctp_transport_walk_start - wrong count at exit The root cause is the missing annotation at sctp_transport_walk_start() Add the missing __acquires(RCU) annotation Signed-off-by:
-
Jules Irenge authored
Sparse reports a warning at sctp_err_finish() warning: context imbalance in sctp_err_finish() - unexpected unlock The root cause is a missing annotation at sctp_err_finish() Add the missing __releases(&((__sk)->sk_lock.slock)) annotation Signed-off-by:
-
Amol Grover authored
ip6mr_for_each_table() macro uses list_for_each_entry_rcu() for traversing outside an RCU read side critical section but under the protection of rtnl_mutex. Hence add the corresponding lockdep expression to silence the following false-positive warnings: [ 4.319479] ============================= [ 4.319480] WARNING: suspicious RCU usage [ 4.319482] 5.5.4-stable #17 Tainted: G E [ 4.319483] ----------------------------- [ 4.319485] net/ipv6/ip6mr.c:1243 RCU-list traversed in non-reader section!! [ 4.456831] ============================= [ 4.456832] WARNING: suspicious RCU usage [ 4.456834] 5.5.4-stable #17 Tainted: G E [ 4.456835] ----------------------------- [ 4.456837] net/ipv6/ip6mr.c:1582 RCU-list traversed in non-reader section!! Signed-off-by:
Amol Grover <frextrite@gmail.com> Signed-off-by:
-
Min Li authored
The IDT 82P33 Synchronization Management Unit (SMU) family provides tools to manage timing references, clock sources and timing paths for IEEE 1588 / Precision Time Protocol (PTP) and Synchronous Ethernet (SyncE) based clocks. The device supports up to three independent timing paths that control: PTP clock synthesis; SyncE clock generation; and general purpose frequency translation. The device supports physical layer timing with Digital PLLs (DPLLs) and it supports packet based timing with Digitally Controlled Oscillators (DCOs). This patch adds support for ptp clock based on the device. Changes since v1: - As suggested by Richard Cochran: 1. Replace _mask_bit_count with the existing hweight8 2. Prefix all functions with idt82p33 3. Fix white space issues in Kconfig and Makefile 4. Remove forward declaration 5. Use adjfine instead of adjfreq for better resolution - As suggested by David Miller: 1. Replace CHAN_INIT macro with a static function idt82p33_channel_init 2. Employ reverse christmas tree ordering for local variables 3. Fix indentation problem by appropriate number of TAB then SPACE character Signed-off-by:Min Li <min.li.xe@renesas.com> Signed-off-by:
-
Min Li authored
Add device tree binding doc for the PTP clock based on IDT 82P33 Synchronization Management Unit (SMU). Changes since v1: - As suggested by Rob Herring: 1. Drop reg description for i2c 2. Replace i2c@1 with i2c 3. Add addtionalProperties: false Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Amol Grover authored
md5sig->head maybe traversed using hlist_for_each_entry_rcu outside an RCU read-side critical section but under the protection of socket lock. Hence, add corresponding lockdep expression to silence false-positive warnings, and harden RCU lists. Signed-off-by:
-
Madhuparna Bhowmik authored
list_for_each_entry_rcu() has built-in RCU and lock checking. Pass cond argument to list_for_each_entry_rcu() to silence false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled by default. Signed-off-by:
Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Signed-off-by:
-
Amol Grover authored
tcp_ulp_list is traversed using list_for_each_entry_rcu outside an RCU read-side critical section but under the protection of tcp_ulp_list_lock. Hence, add corresponding lockdep expression to silence false-positive warnings, and harden RCU lists.t Signed-off-by:
-
David S. Miller authored
Jiri Pirko says: ==================== mlxsw: Introduce ACL traps This patchset allows to track packets that are dropped in HW by ACL. Unlike the existing mlxsw traps, ACL traps are "source traps". That means the action is not controlled by HPKT register but directly in ACL TRAP action. When devlink user changes action from drop to trap and vice versa, it would be needed to go over all instances of ACL TRAP action and do change. That does not scale. Instead, resolve this by introducing "dummy" group with "thin" policer. The purpose of this policer is to drop as many packets as possible. The ones that pass through are going to be dropped in devlink code - patch #6 takes care of that. First four patches are preparation for introduction of ACL traps in mlxsw so it possible to easily change from drop to trap for source traps as well - by changing group to "dummy" and back. ==================== Signed-off-by: -
Jiri Pirko authored
Add a test to check functionality of ACL traps. Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Jiri Pirko authored
Currently the helpers assume pref 1 and handle 101. Make that explicit and pass the values from callers. Signed-off-by:
-
Jiri Pirko authored
Include test of forbidding to have drop rule on mixed-bound shared block. Signed-off-by:
-
Jiri Pirko authored
Add the trap group used to report ACL drops. Setup the trap IDs for ingress/egress flow action drop. Register the two packet traps associated with ACL trap group with devlink during driver initialization. As these are "source traps", set the disabled trap group to be the dummy, discarding as many packets in HW as possible. Signed-off-by:
-
Jiri Pirko authored
For "source traps" it is not possible to change HPKT action to discard. But there is still need to disallow packets arriving to CPU as much as possible. Handle this by introduction of a "dummy group". It has a "thin" policer, which passes as less packets to CPU as possible. The rest is going to be discarded there. The "dummy group" is to be used later on by ACL trap (which is a "source trap"). Signed-off-by:
-
Jiri Pirko authored
Extend the mlxsw_listener struct to contain trap group for disabled traps too. Rename the original "trap_group" item to "en_trap_group" as it represents enabled state. Let both groups be the same for MLXSW_RXL however extend MLXSW_RXL_DIS to register separate groups for enable and disable. Signed-off-by:
-
Jiri Pirko authored
For source traps, the "thin policer" is going to be used in order to reduce the amount of trapped packets to minimum. However, there will be still small number of packets coming in that need to be dropped in the driver. Allow to enable/disable rx_listener related to specific trap in order to prevent unwanted packets to go up the stack. Signed-off-by:
-
Jiri Pirko authored
Introduce a new set of traps: DISCARD_INGRESS_ACL and DISCARD_EGRESS_ACL Set the trap_action from NOP to TRAP which causes the packets dropped by the TRAP action to be trapped under new trap IDs, depending on the ingress/egress binding point. Signed-off-by:
-
Jiri Pirko authored
The ACL flex action will have to know if it is in ingress or egress, so it can use correct trap ID. Pass the ingress indication down to it. Signed-off-by:
-
Jiri Pirko authored
Action drop is going to be tracked by two separate traps, one for ingress and one for egress. Prepare for it and disallow the possibility to have drop action in blocks which are bound to both ingress and egress. Signed-off-by:
-
Jiri Pirko authored
Count the number of ingress and egress block bindings. Use the egress counter in "is_egress_bound" helper. Add couple of helpers to check ingress and mixed bound. Signed-off-by:
-
Jiri Pirko authored
Add packet traps that can report packets that were dropped during ACL processing. Signed-off-by:
-
Jiri Pirko authored
Rename function mlxsw_core_trap_action_set() to mlxsw_core_trap_state_set() and pass bool enabled instead of action. Figure out the action according to the enabled state there. Signed-off-by:
-
Jiri Pirko authored
The listener fields en_action and dis_action now contain the actions to be used for TRAP and DROP devlink trap actions. Use them directly instead of the hard-coded values. Signed-off-by:
-
Jiri Pirko authored
Introduce a new macro MLXSW_RXL_DIS that allows to register listeners as disabled. That allows that from now on, the "action" can be understood always as "enabled action" and "unreg_action" as "disabled action". Rename them and treat them accordingly. Use the new macro for defining drops in spectrum_trap.c. Signed-off-by:
-
