- 22 Feb, 2013 13 commits
-
-
Joe Carnuccio authored
When the Read SFP mailbox command fails on the thermal device, print a message explaining that thermal is not supported. Signed-off-by:
Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com>
-
Masanari Iida authored
Signed-off-by:
Masanari Iida <standby24x7@gmail.com> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
-
Andrew Vasquez authored
There's a subtle race in the loop/bus-reset handling whereby a VHA's loop-state can get incorrectly set to 'down' after the loop-reset and firmware's completion of link re-negotiation. The original code incorrectly assumes that firmware AENs would arrive only after mailbox-command execution to initiate the link-flap. Here's a good case with the old code (AENs arrive after mailbox-command completion): qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:4. qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100. qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received. qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400. qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:4. qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled. qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000. qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps). qla2xxx [0000:03:00.1]-480c:91: Reset marker end. qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled. qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK. qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=170b8f315. qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology. qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260. notice how the 'Port database changed' (8014) arrived after the bus-reset handler completed 'BUS RESET SUCCEEDED'. Now, here's a failing case with the old code (AENs arrive before mailbox-command completion): qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:0. qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received. qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100. qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400. qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping. qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000. qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps). qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:0. qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled. qla2xxx [0000:03:00.1]-480c:91: Reset marker end. qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled. qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK. qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=170be9eb2. qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology. qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260. qla2xxx [0000:03:00.1]-281e:91: Needs RSCN update and loop transition. qla2xxx [0000:03:00.1]-286a:91: qla2x00_configure_loop *** FAILED ***. qla2xxx [0000:03:00.1]-4810:91: Loop resync end. qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping. This race would ultimately lead to devices go unexpectedly offline until another link-flap or chip-reset would cause driver re-discovery to take place. Signed-off-by:
Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
-
Arun Easi authored
Signed-off-by:
Arun Easi <arun.easi@qlogic.com> Signed-off-by:
-
Arun Easi authored
Signed-off-by:
-
Arun Easi authored
Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
Chad Dupuis authored
Base the number of outstanding requests the driver will keep track of on the available resources instead of being hard-coded. Signed-off-by:
-
Dan Carpenter authored
There wasn't any error handling for this kzalloc(). Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Boaz Harrosh <bharrosh@panasas.com> Signed-off-by:
-
Dan Carpenter authored
The error path calls dma_pool_free() on this path but "chap_table" is NULL and "chap_dma" is uninitialized. It's cleaner to just return directly. Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by:
-
Xiangliang Yu authored
Root cause is libsas will clear asd_sas_port phy_mask value in sas_port_deform after triggering destruct workqueue, but the workqueue will send sync cmd and still need phy_mask value. Now, mvsas using asd_sas_phy setting instead of asd_sas_port setting. Signed-off-by:
-
- 30 Jan, 2013 27 commits
-
-
Mahesh Rajashekhara authored
Signed-off-by:
Mahesh Rajashekhara <Mahesh_Rajashekhara@pmc-sierra.com> Signed-off-by:
-
Julia Lawall authored
Delete successive tests to the same location. The code tested the result of a previous allocation, that itself was already tested. It is changed to test the result of the most recent allocation. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @s exists@ local idexpression y; expression x,e; @@ *if ( \(x == NULL\|IS_ERR(x)\|y != 0\) ) { ... when forall return ...; } ... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\) when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\) *if ( \(x == NULL\|IS_ERR(x)\|y != 0\) ) { ... when forall return ...; } // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Acked-by:
Bhanu Prakash Gollapudi <bprakash@broadcom.com> Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Manish Rangankar authored
While reading sysfs chap_in_idx and chap_out_idx attribute, if chap authentication is not set we get an error as "Invalid argument". Signed-off-by:
Manish Rangankar <manish.rangankar@qlogic.com> Signed-off-by:
-
Manish Rangankar authored
Boot from SAN fails in some cases where boot target login response is slow. In this case, probe finishes early and triggers init, which doesn't find remote disk to mount root which leads to BFS failure. Signed-off-by:
-
Vikas Chaudhary authored
This patch force driver to collect firmware dump using following command:- "echo 2 > /sys/class/scsi_host/hostX/device/fw_dump" Signed-off-by:
-
Poornima Vonti authored
Problem: If initialization of adapter fails for some reason, then the interrupt handlers are released. The interrupt handlers are not registered again when initialization of adapter is retried. Solution: Re-register the interrupt handler when adapter initialization is retried. Signed-off-by:
Poornima Vonti <poornima.vonti@qlogic.com> Signed-off-by:
-
Karen Higgins authored
Problem: QLA4xxx firmware may assert if given more IOCBs than it can handle. Solution: The driver was updated to throttle the number of active IOCBs based on the total number of IOCB buffers received from get_firmware_status mbx_sts[2]. Signed-off-by:
Karen Higgins <karen.higgins@qlogic.com> Signed-off-by:
-
Karen Higgins authored
Removed unnecessary calls to qla4xxx_get_firmware_status from function qla4xxx_init_local_data Signed-off-by:
-
Nilesh Javali authored
Quiesce all different activities performed by driver upon the link events while loopback diagnostics is in progress. Signed-off-by:
Nilesh Javali <nilesh.javali@qlogic.com> Signed-off-by:
-
Nilesh Javali authored
Signed-off-by:
-
Nilesh Javali authored
The spurious interrupt messages are seen when interrupt lines are shared between different adapters or modules. Example, interrupt lines are shared between qlcnic and qla4xxx and USB modules, then the console is flooded with flurry of spurious interrupt messages which are expected in such scenario. Hence put these messages under debug level 2 for INTx interrupt mode. Signed-off-by:
-
Thadeu Lima de Souza Cascardo authored
When doing a hotplug remove of a cxgb4 device, there are still dandling symlinks at /sys/class/scsi_host/hostX to the removed PCI device. The upper layer device may also try to send data, which may crash the system. The DETACH message from the lower level driver is sent to the ULD when the device is removed, when the scsi host should be removed from the system, avoiding any problems. After this patch, there are no more dangling symlinks and many attempts to crash the system while there is SCSI activity and removing the device have failed. Adding the device back again works as expected, with the scsi hosts showing up again. Based on a patch by Karen Xie. Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Cc: Karen Xie <kxie@chelsio.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Dan Carpenter authored
The closing parenthesis is in the wrong place so it takes the sizeof a pointer instead of the sizeof the buffer minus one. Signed-off-by:
Anil Gurumurthy <agurumur@brocade.com> Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Nilesh Javali authored
Check mbox_sts[3] instead of mbox_sts[4] for ISP83xx to validate size of data returned Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
James Smart <james.smart@emulex.com> Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Fixed no-context ABTS received on unsolicited receive queue failed with BA_RJT Signed-off-by:
-
James Smart authored
Removed use of NOP mailboxes for interrupt verification in pci_probe_one_s4 Signed-off-by:
-
James Smart authored
Signed-off-by:
-
James Smart authored
Signed-off-by:
-
