I will continue to add new feature and processor support, optimize the
performance, and handle the issues for AMD P-State driver.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Introduce the AMD P-State driver design and implementation.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Introduce sysfs attributes to get the different level AMD P-State
performances.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Introduce sysfs attributes to get the different level processor
frequencies.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

If the sbios supports the boost mode of AMD P-State, let's switch to
boost enabled by default.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Add trace event to monitor the performance value changes which is
controlled by cpu governors.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

In some of Zen2 and Zen3 based processors, they are using the shared
memory that exposed from ACPI SBIOS. In this kind of the processors,
there is no MSR support, so we add acpi cppc function as the backend for
them.

It is using a module param (shared_mem) to enable related processors
manually. We will enable this by default once we address performance
issue on this solution.
Signed-off-by: Jinzhou Su <Jinzhou.Su@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Introduce the fast switch function for AMD P-State on the AMD processors
which support the full MSR register control. It's able to decrease the
latency on interrupt context.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

AMD P-State is the AMD CPU performance scaling driver that introduces a
new CPU frequency control mechanism on AMD Zen based CPU series in Linux
kernel. The new mechanism is based on Collaborative processor
performance control (CPPC) which is finer grain frequency management
than legacy ACPI hardware P-States. Current AMD CPU platforms are using
the ACPI P-states driver to manage CPU frequency and clocks with
switching only in 3 P-states. AMD P-State is to replace the ACPI
P-states controls, allows a flexible, low-latency interface for the
Linux kernel to directly communicate the performance hints to hardware.

AMD P-State leverages the Linux kernel governors such as *schedutil*,
*ondemand*, etc. to manage the performance hints which are provided by CPPC
hardware functionality. The first version for AMD P-State is to support one
of the Zen3 processors, and we will support more in future after we verify
the hardware and SBIOS functionalities.

There are two types of hardware implementations for AMD P-State: one is full
MSR support and another is shared memory support. It can use
X86_FEATURE_CPPC feature flag to distinguish the different types.

Using the new AMD P-State method + kernel governors (*schedutil*,
*ondemand*, ...) to manage the frequency update is the most appropriate
bridge between AMD Zen based hardware processor and Linux kernel, the
processor is able to adjust to the most efficiency frequency according to
the kernel scheduler loading.

Please check the detailed CPU feature and MSR register description in
Processor Programming Reference (PPR) for AMD Family 19h Model 51h,
Revision A1 Processors:

https://www.amd.com/system/files/TechDocs/56569-A1-PUB.zipSigned-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Add a new function to enable CPPC feature. This function
will write Continuous Performance Control package
EnableRegister field on the processor.

CPPC EnableRegister register described in section 8.4.7.1 of ACPI 6.4:
This element is optional. If supported, contains a resource descriptor
with a single Register() descriptor that describes a register to which
OSPM writes a One to enable CPPC on this processor. Before this register
is set, the processor will be controlled by legacy mechanisms (ACPI
Pstates, firmware, etc.).

This register will be used for AMD processors to enable AMD P-State
function instead of legacy ACPI P-States.
Signed-off-by: Jinzhou Su <Jinzhou.Su@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

As this is a static check, it should be based upon what is currently
present on the system. This makes probeing more deterministic.

While local APIC flags field (lapic_flags) of cpu core in MADT table is
0, then the cpu core won't be enabled. In this case, _CPC won't be found
in this core, and return back to _CPC invalid with walking through
possible cpus (include disable cpus). This is not expected, so switch to
check present CPUs instead.
Reported-by: Jinzhou Su <Jinzhou.Su@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

According to the ACPI v6.2 (and later) specification, SystemIO can be
used for _CPC registers. This teaches cppc_acpi how to handle such
registers.

This patch was tested using the amd_pstate driver on my Zephyrus G15
(model GA503QS) using the current version 410 BIOS, which uses
a SystemIO register for the HighestPerformance element in _CPC.
Signed-off-by: Steven Noonan <steven@valvesoftware.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

AMD CPPC (Collaborative Processor Performance Control) function uses MSR
registers to manage the performance hints. So add the MSR register macro
here.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Add Collaborative Processor Performance Control feature flag for AMD
processors.

This feature flag will be used on the following AMD P-State driver. The
AMD P-State driver has two approaches to implement the frequency control
behavior. That depends on the CPU hardware implementation. One is "Full
MSR Support" and another is "Shared Memory Support". The feature flag
indicates the current processors with "Full MSR Support".
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull ARM cpufreq updates for 5.17-rc1 from Viresh Kumar:

"- Qcom cpufreq driver updates improve irq support (Ard Biesheuvel, Stephen Boyd,
   and Vladimir Zapolskiy).

 - Fixes double devm_remap for mediatek driver (Hector Yuan).

 - Introduces thermal pressure helpers (Lukasz Luba)."

* 'cpufreq/arm/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
  cpufreq: mediatek-hw: Fix double devm_remap in hotplug case
  cpufreq: qcom-hw: Use optional irq API
  cpufreq: qcom-hw: Set CPU affinity of dcvsh interrupts
  cpufreq: qcom-hw: Fix probable nested interrupt handling
  cpufreq: qcom-cpufreq-hw: Avoid stack buffer for IRQ name
  arch_topology: Remove unused topology_set_thermal_pressure() and related
  cpufreq: qcom-cpufreq-hw: Use new thermal pressure update function
  cpufreq: qcom-cpufreq-hw: Update offline CPUs per-cpu thermal pressure
  thermal: cpufreq_cooling: Use new thermal pressure update function
  arch_topology: Introduce thermal pressure update function

There are currently 2 ways to create a set of sysfs files for a
kobj_type, through the default_attrs field, and the default_groups
field.  Move the cpufreq code to use default_groups field which has been
the preferred way since aa30f47c ("kobject: Add support for default
attribute groups to kobj_type") so that we can soon get rid of the
obsolete default_attrs field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

When hotpluging policy cpu, cpu policy init will be called multiple times.
Unplug CPU7 -> CPU6 -> CPU5 -> CPU4, then plug CPU4 again.
In this case, devm_remap will double remap and resource allocate fail.
So replace devm_remap to ioremap and release resources in cpu policy exit.
Signed-off-by: Hector.Yuan <hector.yuan@mediatek.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>

With HWP enabled, when the turbo range of performance levels is
disabled by the platform firmware, the CPU capacity is given by
the "guaranteed performance" field in MSR_HWP_CAPABILITIES which
is generally dynamic.  When it changes, the kernel receives an HWP
notification interrupt handled by notify_hwp_interrupt().

When the "guaranteed performance" value changes in the above
configuration, the CPU performance scaling needs to be adjusted so
as to use the new CPU capacity in computations, which means that
the cpuinfo.max_freq value needs to be updated for that CPU.

Accordingly, modify intel_pstate_notify_work() to read
MSR_HWP_CAPABILITIES and update cpuinfo.max_freq to reflect the
new configuration (this update can be carried out even if the
configuration doesn't actually change, because it simply doesn't
matter then and it takes less time to update it than to do extra
checks to decide whether or not a change has really occurred).
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

The min and max frequency QoS requests in the cpufreq core are
initialized to whatever the current min and max frequency values are
at the init time, but if any of these values change later (for
example, cpuinfo.max_freq is updated by the driver), these initial
request values will be limiting the CPU frequency unnecessarily
unless they are changed by user space via sysfs.

To address this, initialize min_freq_req and max_freq_req to
FREQ_QOS_MIN_DEFAULT_VALUE and FREQ_QOS_MAX_DEFAULT_VALUE,
respectively, so they don't really limit anything until user
space updates them.
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

There is an expectation from users that they can get frequency specified
by cpufreq/cpuinfo_max_freq when conditions permit. But with AlderLake
mobile it may not be possible. This is possible that frequency is clipped
based on the system power-up EPP value. In this case users can update
cpufreq/energy_performance_preference to some performance oriented EPP to
limit clipping of frequencies.

To get out of box behavior as the prior generations of CPUs, update EPP
for AlderLake mobile CPUs on boot. On prior generations of CPUs EPP = 128
was enough to get maximum frequency, but with AlderLake mobile the
equivalent EPP is 102. Since EPP is model specific, this is possible that
they have different meaning on each generation of CPU.

The current EPP string "balance_performance" corresponds to EPP = 128.
Change the EPP corresponding to "balance_performance" to 102 for only
AlderLake mobile CPUs and update this on each CPU during boot.

To implement reuse epp_values[] array and update the modified EPP at the
index for BALANCE_PERFORMANCE. Add a dummy EPP_INDEX_DEFAULT to
epp_values[] to match indexes in the energy_perf_strings[].

After HWP PM is enabled also update EPP when "balance_performance" is
redefined for the very first time after the boot on each CPU. On
subsequent suspend/resume or offline/online the old EPP is restored,
so no specific action is needed.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

It is not necessary to call intel_pstate_get_hwp_cap() from
intel_pstate_update_perf_limits(), because it gets called from
intel_pstate_verify_cpu_policy() which is either invoked directly
right before intel_pstate_update_perf_limits(), in
intel_cpufreq_verify_policy() in the passive mode, or called
from driver callbacks in a sequence that causes it to be followed
by an immediate intel_pstate_update_perf_limits().

Namely, in the active mode intel_cpufreq_verify_policy() is called
by intel_pstate_verify_policy() which is the ->verify() callback
routine of intel_pstate and gets called by the cpufreq core right
before intel_pstate_set_policy(), which is the driver's ->setoplicy()
callback routine, where intel_pstate_update_perf_limits() is called.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull USB fixes from Greg KH:
 "Here are some small USB fixes for 5.16-rc5.  They include:

   - gadget driver fixes for reported issues

   - xhci fixes for reported problems.

   - config endpoint parsing fixes for where we got bitfields wrong

  Most of these have been in linux-next, the remaining few were not, but
  got lots of local testing in my systems and in some cloud testing
  infrastructures"

* tag 'usb-5.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: core: config: using bit mask instead of individual bits
  usb: core: config: fix validation of wMaxPacketValue entries
  USB: gadget: zero allocate endpoint 0 buffers
  USB: gadget: detect too-big endpoint 0 requests
  xhci: avoid race between disable slot command and host runtime suspend
  xhci: Remove CONFIG_USB_DEFAULT_PERSIST to prevent xHCI from runtime suspending
  Revert "usb: dwc3: dwc3-qcom: Enable tx-fifo-resize property by default"

Pull char/misc driver fixes from Greg KH:
 "Here are a bunch of small char/misc and other driver subsystem fixes.

  Included in here are:

   - iio driver fixes for reported problems

   - phy driver fixes for a number of reported problems

   - mhi resume bugfix for broken hardware

   - nvmem driver fix

   - rtsx driver fix for irq issues

   - fastrpc packet parsing fix

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (33 commits)
  bus: mhi: core: Add support for forced PM resume
  iio: trigger: stm32-timer: fix MODULE_ALIAS
  misc: rtsx: Avoid mangling IRQ during runtime PM
  nvmem: eeprom: at25: fix FRAM byte_len
  misc: fastrpc: fix improper packet size calculation
  MAINTAINERS: add maintainer for Qualcomm FastRPC driver
  bus: mhi: pci_generic: Fix device recovery failed issue
  iio: adc: stm32: fix null pointer on defer_probe error
  phy: HiSilicon: Fix copy and paste bug in error handling
  dt-bindings: phy: zynqmp-psgtr: fix USB phy name
  phy: ti: omap-usb2: Fix the kernel-doc style
  phy: qualcomm: ipq806x-usb: Fix kernel-doc style
  iio: at91-sama5d2: Fix incorrect sign extension
  iio: adc: axp20x_adc: fix charging current reporting on AXP22x
  iio: gyro: adxrs290: fix data signedness
  phy: ti: tusb1210: Fix the kernel-doc warn
  phy: qualcomm: usb-hsic: Fix the kernel-doc warn
  phy: qualcomm: qmp: Add missing struct documentation
  phy: mvebu-cp110-utmi: Fix kernel-doc warns
  iio: ad7768-1: Call iio_trigger_notify_done() on error
  ...

Pull timer fixes from Thomas Gleixner:
 "Two fixes for clock chip drivers:

   - A regression fix for the Designware APB timer. A recent change to
     the error checking code transformed the error condition wrongly so
     it turned into a fail if good condition.

   - Fix a clang build fail of the ARM architected timer driver"

* tag 'timers-urgent-2021-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/arm_arch_timer: Force inlining of erratum_set_next_event_generic()
  clocksource/drivers/dw_apb_timer_of: Fix probe failure

Pull irq fixes from Thomas Gleixner:
 "A set of interrupt chip driver fixes:

   - Fix the multi vector MSI allocation on Armada 370XP

   - Do interrupt acknowledgement correctly in the aspeed-scu driver

   - Make the IPR register offset correct in the NVIC driver

   - Make redistribution table flushing correct by issueing a SYNC
     command to ensure that the invalidation command has been executed

   - Plug a device tree node reference leak in the bcm7210-l2 driver

   - Trivial fixes in the MIPS GIC and the Apple AIC drivers"

* tag 'irq-urgent-2021-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/irq-bcm7120-l2: Add put_device() after of_find_device_by_node()
  irqchip/irq-gic-v3-its.c: Force synchronisation when issuing INVALL
  irqchip/apple-aic: Mark aic_init_smp() as __init
  irqchip: nvic: Fix offset for Interrupt Priority Offsets
  irqchip/mips-gic: Use bitfield helpers
  irqchip/aspeed-scu: Replace update_bits with write_bits.
  irqchip/armada-370-xp: Fix support for Multi-MSI interrupts
  irqchip/armada-370-xp: Fix return value of armada_370_xp_msi_alloc()

Pull scheduler fix from Thomas Gleixner:
 "A single fix for the x86 scheduler topology:

  Using cluster topology on hybrid CPUs, e.g. Alder Lake, biases the
  scheduler towards the ATOM cluster as that has more total capacity.
  Use selection based on CPU priority instead"

* tag 'sched-urgent-2021-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched,x86: Don't use cluster topology for x86 hybrid CPUs

Pull csky from Guo Ren:
 "Only one fix for csky: fix fpu config macro"

* tag 'csky-for-linus-5.16-rc5' of git://github.com/c-sky/csky-linux:
  csky: fix typo of fpu config macro

Using standard USB_EP_MAXP_MULT_MASK instead of individual bits for
extracting multiple-transactions bits from wMaxPacketSize value.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20211210085219.16796-2-pavel.hofman@ivitera.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The checks performed by commit aed9d65a ("USB: validate
wMaxPacketValue entries in endpoint descriptors") require that initial
value of the maxp variable contains both maximum packet size bits
(10..0) and multiple-transactions bits (12..11). However, the existing
code assings only the maximum packet size bits. This patch assigns all
bits of wMaxPacketSize to the variable.

Fixes: aed9d65a ("USB: validate wMaxPacketValue entries in endpoint descriptors")
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20211210085219.16796-1-pavel.hofman@ivitera.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Under some conditions, USB gadget devices can show allocated buffer
contents to a host.  Fix this up by zero-allocating them so that any
extra data will all just be zeros.
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Tested-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Sometimes USB hosts can ask for buffers that are too large from endpoint
0, which should not be allowed.  If this happens for OUT requests, stall
the endpoint, but for IN requests, trim the request size to the endpoint
buffer size.
Co-developed-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull SCSI fixes from James Bottomley:
 "Four fixes, all in drivers.

  Three are small and obvious, the qedi one is a bit larger but also
  pretty obvious"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: qla2xxx: Format log strings only if needed
  scsi: scsi_debug: Fix buffer size of REPORT ZONES command
  scsi: qedi: Fix cmd_cleanup_cmpl counter mismatch issue
  scsi: pm80xx: Do not call scsi_remove_host() in pm8001_alloc()

Pull xfs fix from Darrick Wong:
 "This fixes a race between a readonly remount process and other
  processes that hold a file IOLOCK on files that previously experienced
  copy on write, that could result in severe filesystem corruption if
  the filesystem is then remounted rw.

  I think this is fairly rare (since the only reliable reproducer I have
  that fits the second criteria is the experimental xfs_scrub program),
  but the race is clear, so we still need to fix this.

  Summary:

   - Fix a data corruption vector that can result from the ro remount
     process failing to clear all speculative preallocations from files
     and the rw remount process not noticing the incomplete cleanup"

* tag 'xfs-5.16-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: remove all COW fork extents when remounting readonly

Pull percpu fixes from Dennis Zhou:
 "This contains a fix for SMP && !MMU archs for percpu which has been
  tested by arm and sh. It seems in the past they have gotten away with
  it due to mapping of vm functions to km functions, but this fell apart
  a few releases ago and was just reported recently.

  The other is just a minor dependency clean up.

  I think queued up right now by Andrew is a fix in percpu that papers
  of what seems to be a bug in hotplug for a special situation with
  memoryless nodes. Michal Hocko is digging into it further"

* 'for-5.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dennis/percpu:
  percpu_ref: Replace kernel.h with the necessary inclusions
  percpu: km: ensure it is used with NOMMU (either UP or SMP)

Merge tag 'perf-tools-fixes-for-v5.16-2021-12-11' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull perf tools fixes from Arnaldo Carvalho de Melo:

 - Prevent out-of-bounds access to per sample registers.

 - Fix NULL vs IS_ERR_OR_NULL() checking on the python binding.

 - Intel PT fixes, half of those are one-liners:
      - Fix some PGE (packet generation enable/control flow packets) usage.
      - Fix sync state when a PSB (synchronization) packet is found.
      - Fix intel_pt_fup_event() assumptions about setting state type.
      - Fix state setting when receiving overflow (OVF) packet.
      - Fix next 'err' value, walking trace.
      - Fix missing 'instruction' events with 'q' option.
      - Fix error timestamp setting on the decoder error path.

* tag 'perf-tools-fixes-for-v5.16-2021-12-11' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf python: Fix NULL vs IS_ERR_OR_NULL() checking
  perf intel-pt: Fix error timestamp setting on the decoder error path
  perf intel-pt: Fix missing 'instruction' events with 'q' option
  perf intel-pt: Fix next 'err' value, walking trace
  perf intel-pt: Fix state setting when receiving overflow (OVF) packet
  perf intel-pt: Fix intel_pt_fup_event() assumptions about setting state type
  perf intel-pt: Fix sync state when a PSB (synchronization) packet is found
  perf intel-pt: Fix some PGE (packet generation enable/control flow packets) usage
  perf tools: Prevent out-of-bounds access to registers

Pull block fixes from Jens Axboe:
 "A few block fixes that should go into this release:

   - NVMe pull request:
        - set ana_log_size to 0 after freeing ana_log_buf (Hou Tao)
        - show subsys nqn for duplicate cntlids (Keith Busch)
        - disable namespace access for unsupported metadata (Keith
          Busch)
        - report write pointer for a full zone as zone start + zone len
          (Niklas Cassel)
        - fix use after free when disconnecting a reconnecting ctrl
          (Ruozhu Li)
        - fix a list corruption in nvmet-tcp (Sagi Grimberg)

   - Fix for a regression on DIO single bio async IO (Pavel)

   - ioprio seteuid fix (Davidlohr)

   - mtd fix that subsequently got reverted as it was broken, will get
     re-done and submitted for the next round

   - Two MD fixes via Song (Markus, zhangyue)"

* tag 'block-5.16-2021-12-10' of git://git.kernel.dk/linux-block:
  Revert "mtd_blkdevs: don't scan partitions for plain mtdblock"
  block: fix ioprio_get(IOPRIO_WHO_PGRP) vs setuid(2)
  md: fix double free of mddev->private in autorun_array()
  md: fix update super 1.0 on rdev size change
  nvmet-tcp: fix possible list corruption for unexpected command failure
  block: fix single bio async DIO error handling
  nvme: fix use after free when disconnecting a reconnecting ctrl
  nvme-multipath: set ana_log_size to 0 after free ana_log_buf
  mtd_blkdevs: don't scan partitions for plain mtdblock
  nvme: report write pointer for a full zone as zone start + zone len
  nvme: disable namespace access for unsupported metadata
  nvme: show subsys nqn for duplicate cntlids

Pull io_uring fixes from Jens Axboe:
 "A few fixes that are all bound for stable:

   - Two syzbot reports for io-wq that turned out to be separate fixes,
     but ultimately very closely related

   - io_uring task_work running on cancelations"

* tag 'io_uring-5.16-2021-12-10' of git://git.kernel.dk/linux-block:
  io-wq: check for wq exit after adding new worker task_work
  io_uring: ensure task_work gets run as part of cancelations
  io-wq: remove spurious bit clear on task_work addition

Pull i2c fixes from Wolfram Sang:
 "Two more I2C driver bugfixes"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: mpc: Use atomic read and fix break condition
  i2c: virtio: fix completion handling

Pull clk driver fixes from Stephen Boyd:

 - Fix qcom mux logic to look at the proper parent table member. Luckily
   this clk type isn't very common.

 - Don't kill clks on qcom systems that use Trion PLLs that are enabled
   out of the bootloader. We will simply skip programming the PLL rate
   if it's already done.

 - Use the proper clk_ops for the qcom sm6125 ICE clks.

 - Use module_platform_driver() in i.MX as it can be a module.

 - Fix a UAF in the versatile clk driver on an error path.

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: versatile: clk-icst: use after free on error path
  clk: qcom: sm6125-gcc: Swap ops of ice and apps on sdcc1
  clk: imx: use module_platform_driver
  clk: qcom: clk-alpha-pll: Don't reconfigure running Trion
  clk: qcom: regmap-mux: fix parent clock lookup