Downloading firmware via BMI protocol takes too long time. For example,
a ~700K bytes firmware takes about 500ms to download via BMI protocol.
This is too long especially in suspend and resume scenario where firmware
is re-downloaded unless WoWLAN is enabled. Downloading firmware via diag CE
can reduce the time to ~40ms for a ~700K bytes firmware binary.

Ath10k driver parses the firmware to segments and downloads the segments
to the specified address directly. If the firmware is compressed or has
unsupported segments, ath10k driver will try BMI download again.

It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

To download firmware via diag interface, driver needs to write the target
memory space below 1M. It means the bit20 should be zero for the converted
address if the target memory space is below 1M. Otherwise, bit20 is one if
the target address is larger or equal to 1M space.

As downloading firmware via diag interface is only required for qca6174
and qca9377, a new specific function is introduced to convert the target
address to ce address: ath10k_pci_qca6174_targ_cpu_to_ce_addri().
This function supports to convert any target address to ce address.

It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Delay 1ms is too long for both diag read and write operations.
This is observed when writing a big memory buffer to target or
reading a big memory buffer from target. Take writing/reading
512k bytes as example, the delay itself is 256ms as the maximum
length of every write/read is 2k size.

Reduce the delay to 50us for read and write operations.

Take the ath10k_pci_targ_cpu_to_ce_addr() out of loop and put it
in the beginning of the loop for ath10k_pci_diag_read_mem().

The ath10k_pci_targ_cpu_to_ce_addr() is to convert the address
from target cpu's perspective to CE's perspective, so it makes
no sense to convert a CE's perspective address again in the loop.
It's a wrong implementation but happens to work.

If the target address is below 1M space, then the convert in the loop
from the second time becomes wrong because the previously converted address
is larger than 1M. The counterpart ath10k_pci_diag_write_mem() has the
correct implementation.

With this change, ath10k_pci_diage_read_mem() works correctly no matter
the target address is below 1M or above 1M.

It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Average ack rssi value is weighted average of ack rssi for
no of msdu's has been sent.
This feature is enabled by the host driver if firmware is capable.
After receiving event from host, firmware allocates the necessary
memory to store the ack_rssi for data packets during the init time.

After each successful transmission, If tx completion status is OK
and 24th bit is set in HTT message header then host will fetch the
ack_rssi else host can ignore the ack_rssi field.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

array "ctl_power_table" access index "pream" is initialized with -1 and
is raised as a static analysis tool issue.
[drivers\net\wireless\ath\ath10k\wmi.c:4719] ->
[drivers\net\wireless\ath\ath10k\wmi.c:4730]: (error) Array index -1 is
out of bounds.

Since the "pream" index for accessing ctl_power_table array is initialized
with -1, there is a chance of memory access violation for the cases below.
1) wmi_pdev_tpc_final_table_event change frequency is between 2483 and 5180
2) pream_idx is out of the enumeration ranges of wmi_tpc_pream_2ghz,
wmi_tpc_pream_5ghz
Signed-off-by: K.T.VIJAYAKUMAAR <vijay.bvb@samsung.com>
[kvalo@codeaurora.org: clean up the warning message]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds 'tx_stats' in per station debugfs entry.

Use this command to dump tx_stats:
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/
    stations/<MACADDR>/tx_stats
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds per station tx statistics support.

Per station tx stats include
 - pkts/bytes transmitted at all possible rates(mcs/nss/bw/gi).
 - ACK fails count
 - ampdu bytes/pkts transmitted at all possible rates(mcs/nss/bw/gi).
 - BA fails count

Tested on QCA9984/QCA4019/QCA988x
Firmware: 10.4-3.5.3-00057
	  10.2.4-1.0-00037
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds debugfs entry to enable/disable extended
tx statistics. Extended tx statistics are from peer stats
feature.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Get the legacy rate index to update the pkts/bytes counter
against each possible tx rate.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The comparison of cid >= 0 is always true because cid is of type u8
(8 bits, unsigned).

Fix this by removing such comparison and updating the type of
variable cid to u8 in the caller function.

Addresses-Coverity-ID: 1473079 ("Unsigned compared against 0")
Fixes: b9010f10 ("wil6210: add FT roam support for AP and station")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

WCN3990 target uses separate htc service for pktlog.
Add pktlog service request and support for pktlog
rx path handling.

Testing:
    Tested on WCN3990 and QCA6174 HW.
    Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1,
               WLAN.RM.4.4.1-00109-QCARMSWPZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Existing copy engine interrupt enable logic assumes that last
CE is using polling mode and due to this interrupt for last copy engine
are always disabled. WCN3990 uses last CE for pktlog and
interrupt remains disabled with existing logic.

To mitigate this issue, introduce CE_ATTR_POLL flag and control
the interrupt based on the flag which can be set in ce_attr.

Testing:
    Tested on WCN3990 and QCA6174 HW.
    Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1,
               WLAN.RM.4.4.1-00109-QCARMSWPZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

To support dual-band variant of QCA9984, new extended board data (eBDF)
is introduced since existing board data ran out of space.

Below is the brief implementation & design detail,
----------------------------------------------------

1. New OTP changes to inform eBDF support in existing OTP download to
fetch board ID and chip ID. This is backward compatible and older
card sends 0 by default for eBDF support bit (bit 18 of OTP response) we
check in ath10k driver.

2. If eBDF is supported, then we need to fetch eBDF ID which is bundled
in downloaded board data. So again OTP is executed for knowing the eBDF ID.
This is done once we set 'board_data_initialized' bit. If eBDF ID
returned is zero, we continue booting with previous board data downloaded.

3. Based on the eBDF ID fetched, ath10k driver tries to download the
extended board data to a new offset ahead of already downloaded board
data address.

4. A new BD IE type, ATH10K_BD_IE_BOARD_EXT is added to differentiate in
bundling eBDF separately in board-2.bin and also to parse through
board bundle for eBDF download in ath10k boot.

5. If eBDF is not present in the board-2.bin bundle or when board ID is
zero, we do a fallback boot to "eboard.bin" in the same QCA9984/hw1.0 dir.
This is same as done to existing "board.bin" if board ID is not present
in board-2.bin bundle.

Current design is that eBDF size will be 2KB and eBDF ID will be
byte value.

Tested the above changes with dual-band variant of QCA9984 card. OTP
update needed for the test will be part of next FW release 10.4-3.6-xxxx.

Below are the logs with ath10k BOOT debugs enabled.

First OTP response :
---------------------
..
boot upload otp to 0x1234 len 9478 for board id
boot get otp board id result 0x00040400 board_id 1 chip_id 0 ext_bid_support 1
..

Second OTP response :
---------------------
..
boot upload otp to 0x1234 len 9478 for ext board id
boot get otp ext board id result 0x00000005 ext_board_id 5
boot using eboard name 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
..

Extended board data download:
------------------------------
..
board name
00000000: 62 75 73 3d 70 63 69 2c 62 6d 69 2d 63 68 69 70  bus=pci,bmi-chip
00000010: 2d 69 64 3d 30 2c 62 6d 69 2d 65 62 6f 61 72 64  -id=0,bmi-eboard
00000020: 2d 69 64 3d 35                                   -id=5
boot found match for name 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
boot found eboard data for 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
using board api 2
boot writing ext board data to addr 0xc3000
..

Fallback Extended board data download from "eboard.bin":
---------------------------------------------------------
..
board name
00000000: 62 75 73 3d 70 63 69 2c 62 6d 69 2d 63 68 69 70  bus=pci,bmi-chip
00000010: 2d 69 64 3d 30 2c 62 6d 69 2d 62 6f 61 72 64 2d  -id=0,bmi-board-
00000020: 69 64 3d 31 30                                   id=10
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-eboard-id=5 from ath10k/QCA9984/hw1.0/board-2.bin
boot fw request 'ath10k/QCA9984/hw1.0/eboard.bin': 0
using board api 1
boot writing ext board data to addr 0xc3000
..
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Just moving functions down in the file, no functional changes.
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ATH10K_SNOC builds just fine with COMPILE_TEST, so make that possible.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If there are some tx packets pending in firmware, and then system
enters suspend, firmware will fail for wow enable. This will trigger
mac80211 to stop ath10k and download firmware again, then it is
non-wow suspend.

After add the waiting htt tx complete, then firmware will have some
time window to send or flush the pending tx packets.

Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1, but this will also affect QCA9377 PCI.
It's not a regression with new firmware releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Devices may provide their own MAC address via system firmware (e.g.,
device tree), especially in the case where the device doesn't have a
useful EEPROM on which to store its MAC address (e.g., for integrated
Wifi).

Use the generic device helper to retrieve the MAC address, and (if
present) honor it above the MAC address advertised by the card.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath.git patches for 4.20. Major changes:

ath10k

* limit available channels via DT ieee80211-freq-limit

wil6210

* add 802.11r Fast Roaming support for AP and station modes

* add support for channel 4

Tri-band devices (1x 2.4GHz + 2x 5GHz) often incorporate special filters in
the RX and TX path. These filtered channel can in theory still be used by
the hardware but the signal strength is reduced so much that it makes no
sense.

There is already a DT property to limit the available channels but ath10k
has to manually call this functionality to limit the currrently set wiphy
channels further.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Check rx_buff_mgmt is allocated before accessing its internal fields.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This feature is needed for enterprise APs and clients to enable
fast roaming as defined in 802.11r between APs in the same ESS.

On AP side, this feature is supported only when disable_ap_sme
is enabled.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

RX SKBs are released in both wil6210 rmmod and RX handle.
As there is no lock to protect the buffers DMA unmap,
the SKB pointer in buff_arr is used to check if the buffer
memory was already released.
Setting wil->rx_buff_mgmt.buff_arr[buff_id].skb to NULL before the DMA
memory unmap will prevent duplicate unmapping of the same memory.
Move the buffer ID to the free list also in case the SKB is NULL.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In enhanced DMA ring 0 is used for RX ring, hence TX ring 0
is an unused element in ring_tx and ring2cid_tid arrays.
Initialize ring2cid_tid CID to WIL6210_MAX_CID to prevent a false
match of CID 0.
Go over the ring_tx and ring2cid_tid from wil_get_min_tx_ring_id
and on to prevent access to index 0 in eDMA.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wil_addba_rx_request allocates the rx reorder buffer regardless
of use_rx_hw_reordering settings.
Fix this by checking wil->use_rx_hw_reordering before allocating
the reorder buffer.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

use_rx_hw_reordering is already set to true in wil_set_capabilities
for Talyn-MB devices. Remove its setting from wil_priv_init to
prevent its activation for older chips.
Similarly, move the setting of use_compressed_rx_status to
wil_set_capabilities.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Delivering a looped-back multicast packet to network stack can cause
higher layer protocols to fail like for example IPv6 DAD.
In STA mode, upon receiving Rx multicast packet, check if the source
MAC address is equal to our own MAC address and if so drop the packet.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wil6210 supports channels 1-3 of the 60GHz band.
New FW added support for channel 4. Add support for channel 4 also in
wil6210 driver.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Reset file is not used and may cause race conditions
with operational driver if used.
Signed-off-by: Karthick Gopalasubramanian <kargop@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Remove extra parentheses to fix the clang warning of extraneous
parentheses.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Tx99 is typically configured via a monitor mode interface, which does
not get added to the driver as a vif. Since the code currently expects
a configured virtual interface for tx99, enabling tx99 via debugfs fails.
Since the vif is not needed anyway, remove all checks for it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@codeaurora.org: s/CPTCFG/CONFIG/]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Array firstep_table is being assigned but is never used
hence it is redundant and can be removed.

Cleans up clang warning:
warning: 'firstep_table' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Remove extra parentheses to fix the clang warning of extraneous
parentheses.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
	int stuff;
        void *entry[];
};

instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.

Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.

The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

WCN3990 has the MAC_PCU_ADDR1 configured properly
and hence it will not send spurious ack frames
during boot up.

Hence the reset_rx_filter workaround is not needed
for WCN3990. Add a hw_param to indicate if hardware rx
filter reset is needed and skip the reset_rx_filter for
WCN3990.

Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Pull networking fixes from David Miller:

 1) ICE, E1000, IGB, IXGBE, and I40E bug fixes from the Intel folks.

 2) Better fix for AB-BA deadlock in packet scheduler code, from Cong
    Wang.

 3) bpf sockmap fixes (zero sized key handling, etc.) from Daniel
    Borkmann.

 4) Send zero IPID in TCP resets and SYN-RECV state ACKs, to prevent
    attackers using it as a side-channel. From Eric Dumazet.

 5) Memory leak in mediatek bluetooth driver, from Gustavo A. R. Silva.

 6) Hook up rt->dst.input of ipv6 anycast routes properly, from Hangbin
    Liu.

 7) hns and hns3 bug fixes from Huazhong Tan.

 8) Fix RIF leak in mlxsw driver, from Ido Schimmel.

 9) iova range check fix in vhost, from Jason Wang.

10) Fix hang in do_tcp_sendpages() with tls, from John Fastabend.

11) More r8152 chips need to disable RX aggregation, from Kai-Heng Feng.

12) Memory exposure in TCA_U32_SEL handling, from Kees Cook.

13) TCP BBR congestion control fixes from Kevin Yang.

14) hv_netvsc, ignore non-PCI devices, from Stephen Hemminger.

15) qed driver fixes from Tomer Tayar.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
  net: sched: Fix memory exposure from short TCA_U32_SEL
  qed: fix spelling mistake "comparsion" -> "comparison"
  vhost: correctly check the iova range when waking virtqueue
  qlge: Fix netdev features configuration.
  net: macb: do not disable MDIO bus at open/close time
  Revert "net: stmmac: fix build failure due to missing COMMON_CLK dependency"
  net: macb: Fix regression breaking non-MDIO fixed-link PHYs
  mlxsw: spectrum_switchdev: Do not leak RIFs when removing bridge
  i40e: fix condition of WARN_ONCE for stat strings
  i40e: Fix for Tx timeouts when interface is brought up if DCB is enabled
  ixgbe: fix driver behaviour after issuing VFLR
  ixgbe: Prevent unsupported configurations with XDP
  ixgbe: Replace GFP_ATOMIC with GFP_KERNEL
  igb: Replace mdelay() with msleep() in igb_integrated_phy_loopback()
  igb: Replace GFP_ATOMIC with GFP_KERNEL in igb_sw_init()
  igb: Use an advanced ctx descriptor for launchtime
  e1000: ensure to free old tx/rx rings in set_ringparam()
  e1000: check on netif_running() before calling e1000_up()
  ixgb: use dma_zalloc_coherent instead of allocator/memset
  ice: Trivial formatting fixes
  ...

The email was botched in one entry, and I also forgot to update the
location of the git tree. It'll be under the linux-block umbrella, just
with different branches.
Reported-by: Baruch Siach <baruch@tkos.co.il>
Fixes: 7634ccd2 ("libata: maintainership update")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Via u32_change(), TCA_U32_SEL has an unspecified type in the netlink
policy, so max length isn't enforced, only minimum. This means nkeys
(from userspace) was being trusted without checking the actual size of
nla_len(), which could lead to a memory over-read, and ultimately an
exposure via a call to u32_dump(). Reachability is CAP_NET_ADMIN within
a namespace.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>