* pci/host-vmd:
  x86/PCI: Add driver for Intel Volume Management Device (VMD)
  PCI/AER: Use 32 bit PCI domain numbers
  x86/PCI: Allow DMA ops specific to a PCI domain
  irqdomain: Export irq_domain_set_info() for module use
  genirq/MSI: Relax msi_domain_alloc() to support parentless MSI irqdomains

The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain.  BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain.  The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.

VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.

This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem.  The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.

VMD routes I/O as follows:

   1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
   address and size for configuration space register access to VMD-owned
   root ports.  It works similarly to MMCONFIG for extended configuration
   space.  Bus numbering is independent and does not conflict with the
   primary domain.

   2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
   base address, size, and type for MMIO register access.  These addresses
   are not translated by VMD hardware; they are simply reservations to be
   distributed to root ports' memory base/limit registers and subdivided
   among devices downstream.

   3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
   and write requests are translated to the bus-device-function of the VMD
   endpoint.  Otherwise, DMA operates normally without VMD-specific address
   translation.

   4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
   PBA.  MSIs from VMD domain devices and ports are remapped to appear as
   if they were issued using one of VMD's MSI-X table entries.  Each MSI
   and MSI-X address of VMD-owned devices and ports has a special format
   where the address refers to specific entries in the VMD's MSI-X table.
   As with DMA, the interrupt source ID is translated to VMD's
   bus-device-function.

   The driver provides its own MSI and MSI-X configuration functions
   specific to how MSI messages are used within the VMD domain, and
   provides an irq_chip for independent IRQ allocation to relay interrupts
   from VMD's interrupt handler to the appropriate device driver's handler.

   5) Errors: PCIe error message are intercepted by the root ports normally
   (e.g., AER), except with VMD, system errors (i.e., firmware first) are
   disabled by default.  AER and hotplug interrupts are translated in the
   same way as endpoint interrupts.

   6) VMD does not support INTx interrupts or IO ports.  Devices or drivers
   requiring these features should either not be placed below VMD-owned
   root ports, or VMD should be disabled by BIOS for such endpoints.

[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)

The Intel Volume Management Device (VMD) supports 32-bit domain numbers.
To accommodate this, use u32 instead of u16 to store domain numbers.

[bhelgaas: changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

The Intel Volume Management Device (VMD) is a PCIe endpoint that acts as a
host bridge to another PCI domain.  When devices below the VMD perform DMA,
the VMD replaces their DMA source IDs with its own source ID.  Therefore,
those devices require special DMA ops.

Add interfaces to allow the VMD driver to set up dma_ops for the devices
below it.

[bhelgaas: remove "extern", add "static", changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Export irq_domain_set_info() for module use.  It will be used by the Volume
Management Device driver.

[bhelgaas: changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>

* pci/hotplug:
  PCI: ibmphp: Remove unneeded NULL test
  PCI: hotplug: Use list_for_each_entry() to simplify code
  PCI: acpiphp_ibm: Fix null dereferences on null ibm_slot

* pci/resource:
  PCI: Avoid iterating through memory outside the resource window
  PCI: Fix minimum allocation address overwrite

Merge branches 'pci/host', 'pci/host-designware', 'pci/host-hisi', 'pci/host-qcom' and 'pci/host-rcar' into next

* pci/host:
  PCI: host: Add of_pci_get_host_bridge_resources() stub
  PCI: host: Mark PCIe/PCI (MSI) IRQ cascade handlers as IRQF_NO_THREAD

* pci/host-designware:
  PCI: designware: Make config accessor override checking symmetric
  PCI: designware: Simplify control flow

* pci/host-hisi:
  PCI: hisi: Add support for HiSilicon Hip06 PCIe host controllers

* pci/host-qcom:
  ARM: dts: ifc6410: enable PCIe DT node for this board
  ARM: dts: apq8064: add PCIe devicetree node
  PCI: qcom: Add Qualcomm PCIe controller driver
  PCI: qcom: Document PCIe devicetree bindings
  PCI: designware: Ensure ATU is enabled before IO/conf space accesses

* pci/host-rcar:
  PCI: rcar: Add Gen2 PHY setup to pcie-rcar
  PCI: rcar: Add runtime PM support to pcie-rcar
  PCI: rcar: Remove unused pci_sys_data struct from pcie-rcar

The pcie-rcar driver can be built for any ARM platform (for COMPILE_TEST)
including those without CONFIG_OF enabled, and that results in a
compile-time error:

  drivers/pci/host/pcie-rcar.c: In function 'rcar_pcie_parse_request_of_pci_ranges':
  drivers/pci/host/pcie-rcar.c:939:8: error: implicit declaration of function 'of_pci_get_host_bridge_resources' [-Werror=implicit-function-declaration]
    err = of_pci_get_host_bridge_resources(np, 0, 0xff, &pci->resources, &iobase);

Add a of_pci_get_host_bridge_resources() stub function defined when
CONFIG_OF_ADDRESS is disabled to allow compile-testing on all platforms.
This mirrors what we do for other OF-specific functions.

Fixes: 5d2917d4 ("PCI: rcar: Convert to DT resource parsing API")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>

Previously msi_domain_alloc() assumed MSI irqdomains always had parent
irqdomains, but that's not true for the new Intel VMD devices.  Relax
msi_domain_alloc() to support parentless MSI irqdomains.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>

For PCIe compliance, the PHY registers need setting as per the manual.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

If runtime PM is enabled in the kernel config, simply enable the clocks
once during probe.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

Drivers based on the DesignWare core can override the config read accessors
by supplying rd_own_conf() and rd_other_conf() function pointers.
dw_pcie_rd_conf() calls dw_pcie_rd_own_conf() (for accesses to the root
bus) or dw_pcie_rd_other_conf():

  dw_pcie_rd_conf
    dw_pcie_rd_own_conf                # if on root bus
    dw_pcie_rd_other_conf              # if not on root bus

Previously we checked for rd_other_conf() directly in dw_pcie_rd_conf(),
but we checked for rd_own_conf() in dw_pcie_rd_own_conf().

Check for rd_other_conf() in dw_pcie_rd_other_conf() to make this symmetric
with the rd_own_conf() checking, and similarly for the write path.

No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>

Remove unneeded NULL test.  The index variable of list_for_each_entry is
never NULL, as it is the structure that contains the list pointer.

Generated by: scripts/coccinelle/iterators/itnull.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Geliang Tang <geliangtang@163.com>

Enable PCIe DT node and fill PCIe DT node with regulator, pinctrl and reset
GPIO, to use the PCIe on the ifc6410 board.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Add the PCIe DT node so that it can probe and be used.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Use list_for_each_entry() instead of list_for_each() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

The pci_sys_data struct was previously used by pci_common_init_dev() and by
the ARM pcibios_align_resource(), but recent commits removed those uses:

  cbce7900 ("PCI: designware: Make driver arch-agnostic")
  b3a72384 ("ARM/PCI: Replace pci_sys_data->align_resource with global function pointer")

cbce7900 removed the use of pci_common_init_dev() by DesignWare
drivers, including pcie-rcar.c, and b3a72384 removed the use of struct
pci_sys_data by the ARM pcibios_align_resource().

Remove struct pci_sys_data from pcie-rcar.c.

[bhelgaas: changelog]
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Add support for the HiSilicon Hip06 SoC.  Documentation has been updated to
include Hip06.  Add Gabriele Paoloni as maintainer of the driver.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>

If the 'image' pointer has been advanced more than 'size', we've already
iterated through memory outside the resource window.

We have zero control over whatever we find in the option ROM, if it's even
an option ROM and not just an accident of random data just happening to
look like an option ROM.
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

ibm_slot_from_id() can return null if the des header signature is not
"aPCI" or if the kmalloc() for the return ACPI descriptor fails, causing
potential null pointer dereferences on the return null descriptor.

Handle the null case with appropriate check and error return.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

* pci/host-generic:
  PCI: generic,versatile: Remove unused pci_sys_data structures

* pci/host-imx6:
  PCI: imx6: Add support for active-low reset GPIO
  PCI: imx6: Use gpio_set_value_cansleep()

* pci/host-iproc:
  PCI: iproc: Add iProc PCIe MSI support
  PCI: iproc: Add iProc PCIe MSI device tree binding
  PCI: iproc: Add PAXC interface support
  PCI: iproc: Update iProc PCIe device tree binding
  PCI: iproc: Do not use 0x in front of %pap
  PCI: iproc: Hide CONFIG_PCIE_IPROC

* pci/host-rcar:
  PCI: rcar: Add gen2 fallback compatibility string for pcie-rcar
  PCI: rcar: Add gen2 fallback compatibility string for pci-rcar-gen2
  PCI: rcar: Add support for R-Car H3 to pcie-rcar
  Revert "PCI: rcar: Build pcie-rcar.c only on ARM"
  PCI: rcar: Convert to DT resource parsing API
  PCI: rcar: Allow DT to override default window settings

Add PCIe MSI support for both PAXB and PAXC interfaces on all iProc-based
platforms.

The iProc PCIe MSI support deploys an event queue-based implementation.
Each event queue is serviced by a GIC interrupt and can support up to 64
MSI vectors.  Host memory is allocated for the event queues, and each event
queue consists of 64 word-sized entries.  MSI data is written to the lower
16-bit of each entry, whereas the upper 16-bit of the entry is reserved for
the controller for internal processing.

Each event queue is tracked by a head pointer and tail pointer.  Head
pointer indicates the next entry in the event queue to be processed by
the driver and is updated by the driver after processing is done.
The controller uses the tail pointer as the next MSI data insertion
point.  The controller ensures MSI data is flushed to host memory before
updating the tail pointer and then triggering the interrupt.

MSI IRQ affinity is supported by evenly distributing the interrupts to each
CPU core.  MSI vector is moved from one GIC interrupt to another in order
to steer to the target CPU.

Therefore, the actual number of supported MSI vectors is:

  M * 64 / N

where M denotes the number of GIC interrupts (event queues), and N denotes
the number of CPU cores.

This iProc event queue-based MSI support should not be used with newer
platforms with integrated MSI support in the GIC (e.g., giv2m or
gicv3-its).

[bhelgaas: fold in Kconfig fixes from Arnd Bergmann <arnd@arndb.de>]
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>

On -RT and if kernel is booting with "threadirqs" cmd line parameter,
PCIe/PCI (MSI) IRQ cascade handlers (like dra7xx_pcie_msi_irq_handler())
will be forced threaded and, as result, will generate warnings like this:

  WARNING: CPU: 1 PID: 82 at kernel/irq/handle.c:150 handle_irq_event_percpu+0x14c/0x174()
  irq 460 handler irq_default_primary_handler+0x0/0x14 enabled interrupts
  Backtrace:
   (warn_slowpath_common) from (warn_slowpath_fmt+0x38/0x40)
   (warn_slowpath_fmt) from (handle_irq_event_percpu+0x14c/0x174)
   (handle_irq_event_percpu) from (handle_irq_event+0x84/0xb8)
   (handle_irq_event) from (handle_simple_irq+0x90/0x118)
   (handle_simple_irq) from (generic_handle_irq+0x30/0x44)
   (generic_handle_irq) from (dra7xx_pcie_msi_irq_handler+0x7c/0x8c)
   (dra7xx_pcie_msi_irq_handler) from (irq_forced_thread_fn+0x28/0x5c)
   (irq_forced_thread_fn) from (irq_thread+0x128/0x204)

This happens because all of them invoke generic_handle_irq() from the
requested handler.  generic_handle_irq() grabs raw_locks and thus needs to
run in raw-IRQ context.

This issue was originally reproduced on TI dra7-evem, but, as was
identified during discussion [1], other hosts can also suffer from this
issue.  Fix all them at once by marking PCIe/PCI (MSI) IRQ cascade handlers
IRQF_NO_THREAD explicitly.

[1] http://lkml.kernel.org/r/1448027966-21610-1-git-send-email-grygorii.strashko@ti.com

[bhelgaas: add stable tag, fix typos]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de> (for imx6)
CC: stable@vger.kernel.org
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Kukjin Kim <kgene@kernel.org>
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
CC: Richard Zhu <Richard.Zhu@freescale.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
CC: Sebastian Andrzej Siewior <bigeasy@linutronix.de>

Commit 36e097a8 ("PCI: Split out bridge window override of minimum
allocation address") claimed to do no functional changes but unfortunately
did: The "min" variable is altered.  At least the AVM A1 PCMCIA adapter was
no longer detected, breaking ISDN operation.

Use a local copy of "min" to restore the previous behaviour.

[bhelgaas: avoid gcc "?:" extension for portability and readability]
Fixes: 36e097a8 ("PCI: Split out bridge window override of minimum allocation address")
Signed-off-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org      # v3.14+

Return values immediately when possible to simplify the control flow.

No functional change intended.  Folded in unused variable removal as
pointed out by Fabio Estevam <fabio.estevam@nxp.com>, Arnd Bergmann
<arnd@arndb.de>, and Thierry Reding <thierry.reding@gmail.com>.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>

The PCIe driver reuses the Designware common code for host and MSI
initialization, and also programs the Qualcomm application specific
registers.

[bhelgaas: remove COMPILE_TEST Kconfig dependency]
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Document Qualcomm PCIe driver devicetree bindings.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>

Read back the ATU CR2 register to ensure ATU programming is effective
before any subsequent I/O or config space accesses.

Without this, PCI device enumeration is unreliable.

[bhelgaas: changelog, comment]
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>

* pci/aspm:
  PCI/ASPM: Make sysfs link_state_store() consistent with link_state_show()

* pci/hotplug:
  PCI: pciehp: Always protect pciehp_disable_slot() with hotplug mutex

* pci/misc:
  x86/PCI: Simplify pci_bios_{read,write}
  PCI: Simplify config space size computation
  PCI: Limit config space size for Netronome NFP6000 family
  PCI: Add Netronome vendor and device IDs
  PCI: Support PCIe devices with short cfg_size
  x86/PCI: Clarify AMD Fam10h config access restrictions comment
  PCI: Print warnings for all invalid expansion ROM headers
  PCI: Check for PCI_HEADER_TYPE_BRIDGE equality, not bitmask

* pci/msi:
  PCI/MSI: Remove empty pci_msi_init_pci_dev()
  PCI/MSI: Initialize MSI capability for all architectures

There is some repetitive code in the switch/case statements in
pci_bios_read() and pci_bios_write().  Factor out the BIOS function
IDs and the result widths to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>

Restructure the logic so we return the config space size as soon as we know
it.  This reduces indentation, removes negations, and removes gotos.

No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

The NFP6000 has an erratum where reading/writing to PCI config space
addresses above 0x600 can cause the NFP to generate PCIe completion
timeouts.

Limit the NFP6000's config space size to 0x600 bytes.
Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
[simon: edited changelog]
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Device IDs for the Netronome NFP3200, NFP3240, NFP6000, and NFP6000 SR-IOV
devices.
Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
[simon: edited changelog]
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

If a device quirk modifies the pci_dev->cfg_size to be less than
PCI_CFG_SPACE_EXP_SIZE (4096), but greater than PCI_CFG_SPACE_SIZE (256),
the PCI sysfs interface truncates the readable size to PCI_CFG_SPACE_SIZE.

Allow sysfs access to config space up to cfg_size, even if the device
doesn't support the entire 4096-byte PCIe config space.

Note that pci_read_config() and pci_write_config() limit access to
dev->cfg_size even though pcie_config_attr contains 4096 (the maximum
size).
Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
[simon: edited changelog]
Signed-off-by: Simon Horman <simon.horman@netronome.com>
[bhelgaas: more changelog edits]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Clarify the comment about AMD Fam10h config access restrictions, fix typos,
and add a reference to the specification.

[bhelgaas: streamline]
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>

We've always validated that both bytes of the Expansion ROM signature and
all four bytes of the PCI Data Structure signature (see PCI Firmware spec
r3.0, sec 5.1.1), but we only printed a warning if the first byte of the
ROM signature was invalid.

Print warnings if *any* of those bytes are invalid.  Note that we only look
at these headers if we map or read the ROM.

[bhelgaas: changelog, tweak printk format]
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Bit 7 of the "Header Type" register indicates a multi-function device when
set.  Bits 0-6 contain encoded values, where 0x1 indicates a PCI-PCI
bridge.  It is incorrect to test this as though it were a mask.

For example, while the PCI 3.0 spec only defines values 0x0, 0x1, and 0x2,
it's conceivable that a future spec could define 0x3 to mean something
else; then tests for "(hdr_type & 0x7f) & PCI_HEADER_TYPE_BRIDGE" would
incorrectly succeed for this new 0x3 header type.

Test bits 0-6 of the Header Type for equality with PCI_HEADER_TYPE_BRIDGE.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Add fallback compatibility string for R-Car Gen 2 family.  This is in
keeping with the fallback scheme being adopted wherever appropriate for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Add fallback compatibility string for R-Car Gen 2 family.  This is in
keeping with the fallback scheme being adopted wherever appropriate for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>

Add the "renesas,pcie-r8a7795" property for the R-Car H3 device to the
pcie-rcar driver.
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Harunobu Kurokawa <harunobu.kurokawa.dn@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>