For offload iSCSI like qla4xxx, CHAP entries are stored in adapter's
flash.
This patch adds support to add/update CHAP entries in adapter's flash
using iscsi tools, like Open-iSCSI.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

To write a CHAP entry in adapter's flash calculate the offset based
on the type of adapter.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

If any flash target entry is using CHAP authentication then set
CHAP username and password sysfs params for the corresponding
iscsi sessions.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Support setting of CHAP_OUT_IDX param for the target entry in flash.
Setting of valid local CHAP index with enable CHAP AUTH for that
flash target entry and disabling CHAP AUTH will invalidate the CHAP
index for the flash target entry.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Earlier logic for driver created iscsi_session->discovery_parent_idx
was to store ram index of a sendtarget entry, but driver frees
sendtarget ram index as soon as firmware is done with discovery,
which is available for further use. So changing the logic to point
iscsi_session->discovery_parent_idx to store sendtarget flashnode index.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Fixed two issues in this patch-
1) In function megasas_get_pd_list(), data read(pd_addr->deviceId) from DMAed memory is converted to CPU's endianess.
2) While register AEN, removed some endianness conversion on some fields, since their endianess is already converted.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Added check for DMA mapping errors for request sense data
buffer. Checking for mapping error can avoid potential wild
writes. This patch was prompted by the warning from
dma_unmap when kernel is compiled with CONFIG_DMA_API_DEBUG.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This feature gathers active and cumulative per fnic stats for io,
abort, terminate, reset, vlan discovery path and it also includes
various important stats for debugging issues. It also provided
debugfs and ioctl interface for user to retrieve these stats.
It also provides functionality to reset cumulative stats through
user interface.
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Fixed appropriate error codes that returns negative error number on failure,
and 0 on success. fnic_reset() is used directly by the fc transport callback
issue_fc_host_lip which requires a negative error number on failure.
Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

If you mutiple devices connect to a host, we might be interested in
have an intensive I/O workload on one disk, and notice starvation on others.
This give the user more hint about current infight io for scsi device.
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Sean Stewart <Sean.Stewart@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

The PCIE capability offset is saved during PCI bus walking.  It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.  Also, pci_is_pcie is a
better way of determining if the device is PCIE or not (as it uses the
same saved PCIE capability offset).
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This patch removes the PCI ID of a cancelled Smart Array.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Sujit has found a race condition that would make q->nr_pending
unbalanced, it occurs as Sujit explained:

"
sd_probe_async() ->
	add_disk() ->
		disk_add_event() ->
			schedule(disk_events_workfn)
	sd_revalidate_disk()
	blk_pm_runtime_init()
return;

Let's say the disk_events_workfn() calls sd_check_events() which tries
to send test_unit_ready() and because of sd_revalidate_disk() trying to
send another commands the test_unit_ready() might be re-queued as the
tagged command queuing is disabled.

So the race condition is -

Thread 1 			  |		Thread 2
sd_revalidate_disk()		  |	sd_check_events()
...nr_pending = 0 as q->dev = NULL|	scsi_queue_insert()
blk_runtime_pm_init()		  | 	blk_pm_requeue_request() ->
				  |	nr_pending = -1 since
				  |	q->dev != NULL
"

The problem is, the test_unit_ready request doesn't get counted the
first time it is queued, so the later decrement of q->nr_pending in
blk_pm_requeue_request makes it unbalanced.

Fix this by calling blk_pm_runtime_init before add_disk so that all
requests initiated there will all be counted.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reported-and-tested-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

If an invalid IOCB is returned on the response queue then the index into the
request queue map could be invalid and could return to us a bogus value. This
could cause us to try to deference an invalid pointer and cause an exception.

If we encounter this condition, simply return as no context can be established
for this response.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This fixes an oops caused by buslogic driver when initializing a BusLogic
MultiMaster adapter. Initialization code used scope of a variable
incorrectly which created a NULL pointer. Oops message is below:

BUG: unable to handle kernel NULL pointer dereference at 0000000c
IP: [<c150c137>] blogic_init_mm_probeinfo.isra.17+0x20a/0x583
*pde = 00000000
Oops: 002 [#1] PREEMPT SMP
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.11.1.puz1 #1
Hardware name:    /Canterwood, BIOS 6.00 PG 05/16/2003
task: f7050000 ti: f7054000 task.ti: f7054000
EIP: 0060:[<c150c137>] EFLAGS: 00010246 CPU:1
EIP is at blogic_init_mm_probeinfo.isra.17+0x20a/0x583
EAX: 00000013 EBX: 00000000 ECX: 00000000 EDX: f8001000
ESI: f71cb800 EDI: f7388000 EBP: 00007800 ESP: f7055c84
 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 8005003b CR2: 0000000c CR3: 0154f000 CR4: 000007d0
Stack:
 0000001c 00000000 c11a59f6 f7055c98 00008130 ffffffff ffffffff 00000000
 00000003 00000000 00000000 00000000 00000013 f8001000 00000001 000003d0
 00000000 00000000 00000000 c14e3f84 f78803c8 00000000 f738c000 000000e9
Call Trace:
 [<c11a59f6>] ? pci_get_subsys+0x33/0x38
 [<c150c4fb>] ? blogic_init_probeinfo_list+0x4b/0x19e
 [<c108d593>] ? __alloc_pages_nodemask+0xe3/0x623
 [<c108d593>] ? __alloc_pages_nodemask+0xe3/0x623
 [<c10fb99e>] ? sysfs_link_sibling+0x61/0x8d
 [<c10b0519>] ? kmem_cache_alloc+0x8b/0xb5
 [<c150cce5>] ? blogic_init+0xa1/0x10e8
 [<c10fc0a8>] ? sysfs_add_one+0x10/0x9d
 [<c10fc18a>] ? sysfs_addrm_finish+0x12/0x85
 [<c10fca37>] ? sysfs_do_create_link_sd+0x9d/0x1b4
 [<c117c272>] ? blk_register_queue+0x69/0xb3
 [<c10fcb68>] ? sysfs_create_link+0x1a/0x2c
 [<c1181a07>] ? add_disk+0x1a1/0x3c7
 [<c138737b>] ? klist_next+0x60/0xc3
 [<c122cc3a>] ? scsi_dh_detach+0x68/0x68
 [<c1213e36>] ? bus_for_each_dev+0x51/0x61
 [<c1000356>] ? do_one_initcall+0x22/0x12c
 [<c10f3688>] ? __proc_create+0x8c/0xba
 [<c150cc44>] ? blogic_setup+0x5f6/0x5f6
 [<c14e94aa>] ? repair_env_string+0xf/0x4d
 [<c14e949b>] ? do_early_param+0x71/0x71
 [<c103efaa>] ? parse_args+0x21f/0x33d
 [<c14e9a54>] ? kernel_init_freeable+0xdf/0x17d
 [<c14e949b>] ? do_early_param+0x71/0x71
 [<c1388b64>] ? kernel_init+0x8/0xc0
 [<c1392222>] ? ret_from_kernel_thread+0x6/0x28
 [<c1392227>] ? ret_from_kernel_thread+0x1b/0x28
 [<c1388b5c>] ? rest_init+0x6c/0x6c
Code: 89 44 24 10 0f b6 44 24 3d 89 44 24 0c c7 44 24 08 00 00 00 00 c7 44 24 04 38 62 46 c1 c7 04 24 02 00 00 00 e8 78 13 d2 ff 31 db <89> 6b 0c b0 20 89 ea ee
 c7 44 24 08 04 00 00 00 8d 44 24 4c 89
EIP: [<c150c137>] blogic_init_mm_probeinfo.isra.17+0x20a/0x583 SS:ESP 0068:f7055c84
CR2: 000000000000000c
---[ end trace 17f45f5196d40487 ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: <stable@vger.kernel.org> # 3.11.x
Reported-by: Pierre Uszynski <pierre@rahul.net>
Tested-by: Pierre Uszynski <pierre@rahul.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Pull watchdog fixes from Wim Van Sebroeck:
 "This will fix a deadlock on the ts72xx_wdt driver, fix bitmasks in the
  kempld_wdt driver and fix a section mismatch in the sunxi_wdt driver"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: sunxi: Fix section mismatch
  watchdog: kempld_wdt: Fix bit mask definition
  watchdog: ts72xx_wdt: locking bug in ioctl

This driver has a section mismatch, for probe and remove functions,
leading to the following warning during the compilation.

WARNING: drivers/watchdog/built-in.o(.data+0x24): Section mismatch in
reference from the variable sunxi_wdt_driver to the function
.init.text:sunxi_wdt_probe()
The variable sunxi_wdt_driver references
the function __init sunxi_wdt_probe()
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

STAGE_CFG bits are defined as [5:4] bits. However, '(((x) & 0x30) << 4)'
handles [9:8] bits. Thus, it should be fixed in order to handle
[5:4] bits.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Calling the WDIOC_GETSTATUS & WDIOC_GETBOOTSTATUS and twice will cause a
interruptible deadlock.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Pull ARM SoC fixes from Olof Johansson:
 "A small batch of fixes this week, mostly OMAP related.  Nothing stands
  out as particularly controversial.

  Also a fix for a 3.12-rc1 timer regression for Exynos platforms,
  including the Chromebooks"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: exynos: dts: Update 5250 arch timer node with clock frequency
  ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config
  ARM: mach-omap2: board-generic: fix undefined symbol
  ARM: dts: Fix pinctrl mask for omap3
  ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree
  ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT

Without the "clock-frequency" property in arch timer node, could able
to see the below crash dump.

[<c0014e28>] (unwind_backtrace+0x0/0xf4) from [<c0011808>] (show_stack+0x10/0x14)
[<c0011808>] (show_stack+0x10/0x14) from [<c036ac1c>] (dump_stack+0x7c/0xb0)
[<c036ac1c>] (dump_stack+0x7c/0xb0) from [<c01ab760>] (Ldiv0_64+0x8/0x18)
[<c01ab760>] (Ldiv0_64+0x8/0x18) from [<c0062f60>] (clockevents_config.part.2+0x1c/0x74)
[<c0062f60>] (clockevents_config.part.2+0x1c/0x74) from [<c0062fd8>] (clockevents_config_and_register+0x20/0x2c)
[<c0062fd8>] (clockevents_config_and_register+0x20/0x2c) from [<c02b8e8c>] (arch_timer_setup+0xa8/0x134)
[<c02b8e8c>] (arch_timer_setup+0xa8/0x134) from [<c04b47b4>] (arch_timer_init+0x1f4/0x24c)
[<c04b47b4>] (arch_timer_init+0x1f4/0x24c) from [<c04b40d8>] (clocksource_of_init+0x34/0x58)
[<c04b40d8>] (clocksource_of_init+0x34/0x58) from [<c049ed8c>] (time_init+0x20/0x2c)
[<c049ed8c>] (time_init+0x20/0x2c) from [<c049b95c>] (start_kernel+0x1e0/0x39c)

THis is because the Exynos u-boot, for example on the Chromebooks, doesn't set
up the CNTFRQ register as expected by arch_timer. Instead, we have to specify
the frequency in the device tree like this.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
[olof: Changed subject, added comment, elaborated on commit message]
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'fixes-against-v3.12-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:

Few fixes for omap3 related hangs and errors that people have
noticed now that people are actually using the device tree
based booting for omap3.

Also one regression fix for timer compile for dra7xx when
omap5 is not selected, and a LED regression fix for n900.

* tag 'fixes-against-v3.12-rc3-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2: RX-51: Add missing max_current to rx51_lp5523_led_config
  ARM: mach-omap2: board-generic: fix undefined symbol
  ARM: dts: Fix pinctrl mask for omap3
  ARM: OMAP3: Fix hardware detection for omap3630 when booted with device tree
  ARM: OMAP2: gpmc-onenand: fix sync mode setup with DT
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull parisc fixes from Helge Deller:
 "This patchset includes a bugfix to prevent a kernel crash when memory
  in page zero is accessed by the kernel itself, e.g.  via
  probe_kernel_read().

  Furthermore we now export flush_cache_page() which is needed
  (indirectly) by the lustre filesystem.  The other patches remove
  unused functions and optimizes the page fault handler to only evaluate
  variables if needed, which again protects against possible kernel
  crashes"

* 'parisc-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: let probe_kernel_read() capture access to page zero
  parisc: optimize variable initialization in do_page_fault
  parisc: fix interruption handler to respect pagefault_disable()
  parisc: mark parisc_terminate() noreturn and cold.
  parisc: remove unused syscall_ipi() function.
  parisc: kill SMP single function call interrupt
  parisc: Export flush_cache_page() (needed by lustre)

Pull slave-dmaengine fixes from Vinod Koul:
 "Another week, time to send another fixes request taking time out of
  extended weekend for the festivities in this part of the world.

  We have two fixes from Sergei for rcar driver and one fixing memory
  leak of edma driver by Geyslan"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dma: edma.c: remove edma_desc leakage
  rcar-hpbdma: add parameter to set_slave() method
  rcar-hpbdma: remove shdma_free_irq() calls

Signed-off-by: Helge Deller <deller@gmx.de>

The attached change defers the initialization of the variables tsk, mm
and flags until they are needed. As a result, the code won't crash if a
kernel probe is done with a corrupt context and the code will be better
optimized.
Signed-off-by: John David Anglin  <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>

Running an "echo t > /proc/sysrq-trigger" crashes the parisc kernel.  The
problem is, that in print_worker_info() we try to read the workqueue info via
the probe_kernel_read() functions which use pagefault_disable() to avoid
crashes like this:
    probe_kernel_read(&pwq, &worker->current_pwq, sizeof(pwq));
    probe_kernel_read(&wq, &pwq->wq, sizeof(wq));
    probe_kernel_read(name, wq->name, sizeof(name) - 1);

The problem here is, that the first probe_kernel_read(&pwq) might return zero
in pwq and as such the following probe_kernel_reads() try to access contents of
the page zero which is read protected and generate a kernel segfault.

With this patch we fix the interruption handler to call parisc_terminate()
directly only if pagefault_disable() was not called (in which case
preempt_count()==0).  Otherwise we hand over to the pagefault handler which
will try to look up the faulting address in the fixup tables.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: John David Anglin  <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>

Signed-off-by: Helge Deller <deller@gmx.de>

Signed-off-by: Helge Deller <deller@gmx.de>

Commit 9a46ad6d "smp: make smp_call_function_many() use logic
similar to smp_call_function_single()" has unified the way to handle
single and multiple cross-CPU function calls. Now only one interrupt
is needed for architecture specific code to support generic SMP function
call interfaces, so kill the redundant single function call interrupt.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>

ERROR: "flush_cache_page" [drivers/staging/lustre/lustre/libcfs/libcfs.ko] undefined!
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Helge Deller <deller@gmx.de>

Olga reported that file descriptors opened with O_PATH do not work with
fstatfs(), found during further development of ksh93's thread support.

There is no reason to not allow O_PATH file descriptors here (fstatfs is
very much a path operation), so use "fdget_raw()".  See commit
55815f70 ("vfs: make O_PATH file descriptors usable for 'fstat()'")
for a very similar issue reported for fstat() by the same team.
Reported-and-tested-by: ольга крыжановская <olga.kryzhanovska@gmail.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org	# O_PATH introduced in 3.0+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ext4 bugfixes from Ted Ts'o:
 "A bug fix and performance regression fix for ext4"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix memory leak in xattr
  ext4: fix performance regression in writeback of random writes

Pull btrfs fixes from Chris Mason:
 "We've got more bug fixes in my for-linus branch:

  One of these fixes another corner of the compression oops from last
  time.  Miao nailed down some problems with concurrent snapshot
  deletion and drive balancing.

  I kept out one of his patches for more testing, but these are all
  stable"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix oops caused by the space balance and dead roots
  Btrfs: insert orphan roots into fs radix tree
  Btrfs: limit delalloc pages outside of find_delalloc_range
  Btrfs: use right root when checking for hash collision

Pull sound fixes from Takashi Iwai:
 "All stable fixes except for a trivial headset mic fixup: the removal
  of bogus frame checks in snd-usb-usx2y driver that have regressed in
  the recent kernel versions, the HD-audio HDMI channel map fix, and a
  few HD-audio device-specific fixes"

* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Sony VAIO Pro 13 (haswell) now has a working headset jack
  ALSA: hda - Add a headset mic model for ALC269 and friends
  ALSA: hda - Fix microphone for Sony VAIO Pro 13 (Haswell model)
  ALSA: hda - Add fixup for ASUS N56VZ
  ALSA: hda - hdmi: Fix channel map switch not taking effect
  ALSA: hda - Fix mono speakers and headset mic on Dell Vostro 5470
  ALSA: snd-usb-usx2y: remove bogus frame checks

Pull i2c fixes from Wolfram Sang:
 "We had various reports of problems with deferred probing in the I2C
  subsystem, so this pull requst is a little bigger than usual.

  Most issues should be addressed now so devices will be found
  correctly.  A few ususal driver bugfixes are in here, too"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i2c-mux-pinctrl: use deferred probe when adapter not found
  i2c: i2c-arb-gpio-challenge: use deferred probe when adapter not found
  i2c: i2c-mux-gpio: use deferred probing
  i2c: i2c-mux-gpio: don't ignore of_get_named_gpio errors
  i2c: omap: Clear ARDY bit twice
  i2c: Not all adapters have a parent
  i2c: i2c-stu300: replace platform_driver_probe to support deferred probing
  i2c: i2c-mxs: replace platform_driver_probe to support deferred probing
  i2c: i2c-imx: replace platform_driver_probe to support deferred probing
  i2c: i2c-designware-platdrv: replace platform_driver_probe to support deferred probing