- 28 Feb, 2024 34 commits
-
-
Icenowy Zheng authored
Voltafield AF8133J is a simple magnetometer sensor produced by Voltafield Technology Corp, with dual power supplies (one for core and one for I/O) and active-low reset pin. The sensor has configurable range 1.2 - 2.2 mT and a software controlled standby mode. Add a device tree binding for it. Signed-off-by:
Icenowy Zheng <icenowy@aosc.io> Signed-off-by:
Ondřej Jirman <megi@xff.cz> Reviewed-by:
Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20240222011341.3232645-3-megi@xff.czSigned-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Icenowy Zheng authored
Voltafile Technology Corp. is a company that produces MEMS sensors. Add a DT vendor prefix for it. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240222011341.3232645-2-megi@xff.czSigned-off-by:
-
Quentin Schulz authored
devm_reset_control_get_optional_exclusive does what this driver is trying to do in its probe function, therefore let's switch over to that subsystem function. Signed-off-by:
Quentin Schulz <quentin.schulz@theobroma-systems.com> Reviewed-by:
Heiko Stuebner <heiko@sntech.de> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20240223-saradcv2-chan-mask-v1-3-84b06a0f623a@theobroma-systems.comSigned-off-by:
-
Quentin Schulz authored
Some of the registers on the SARADCv2 have bits write protected except if another bit is set. This is usually done by having the lowest 16 bits store the data to write and the highest 16 bits specify which of the 16 lowest bits should have their value written to the hardware block. The write_enable mask for the channel selection was incorrect because it was just the value shifted by 16 bits, which means it would only ever write bits and never clear them. So e.g. if someone starts a conversion on channel 5, the lowest 4 bits would be 0x5, then starts a conversion on channel 0, it would still be 5. Instead of shifting the value by 16 as the mask, let's use the OR'ing of the appropriate masks shifted by 16. Note that this is not an issue currently because the only SARADCv2 currently supported has a reset defined in its Device Tree, that reset resets the SARADC controller before starting a conversion on a channel. However, this reset is handled as optional by the probe function and thus proper masking should be used in the event an SARADCv2 without a reset ever makes it upstream. Fixes: 757953f8 ("iio: adc: rockchip_saradc: Add support for RK3588") Signed-off-by:
-
Quentin Schulz authored
The SARADCv2 on RK3588 (the only SoC currently supported that has an SARADCv2) selects the channel through the channel_sel bitfield which is the 4 lowest bits, therefore the mask should be GENMASK(3, 0) and not GENMASK(15, 0). Fixes: 757953f8 ("iio: adc: rockchip_saradc: Add support for RK3588") Signed-off-by:
-
Javier Carrasco authored
The VEML6075 requires a single supply to operate. The property already exists in the bindings and it is used in the example, but it is still not on the list of required properties. Signed-off-by:
Javier Carrasco <javier.carrasco.cruz@gmail.com> Acked-by:
-
Marius Cristea authored
This is the iio driver for Microchip PAC193X series of Power Monitor with Accumulator chip family. Signed-off-by:
Marius Cristea <marius.cristea@microchip.com> Link: https://lore.kernel.org/r/20240222164206.65700-3-marius.cristea@microchip.comSigned-off-by:
-
Marius Cristea authored
This is the device tree schema for iio driver for Microchip PAC193X series of Power Monitors with Accumulator. Signed-off-by:
-
Nuno Sa authored
Getting the part name with 'spi_get_device_id(spi)->name' is not a very good pattern. Hence, explicitly add the name in the struct chip_info and use that instead. Signed-off-by:
Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20240222-ltc2983-misc-improv-v1-4-cf7d4457e98c@analog.comSigned-off-by:
-
Nuno Sa authored
Rename ltc2983_parse_dt() to ltc2983_parse_fw() as there's no explicit dependency on devicetree. No functional change intended... Signed-off-by:
-
Nuno Sa authored
Use spi_get_device_match_data() as it simplifies the code. No functional change intended... Signed-off-by:
-
Dan Carpenter authored
The "val" variable comes from the user so we need to ensure that it's not zero. In fact, all negative values are invalid as well. Add a check for that. Fixes: 00ef7708 ("iio: adc: ti-ads1298: Add driver") Acked-by:
Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by:
Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/r/c32c9087-86de-423b-8101-67b4a7f9d728@moroto.mountainSigned-off-by:
-
Dan Carpenter authored
There is a copy and paste bug here, it should be "reg_vref" instead of "reg_avdd". The "priv->reg_avdd" variable is zero so it ends up returning success. Fixes: 00ef7708 ("iio: adc: ti-ads1298: Add driver") Signed-off-by:
-
Ramona Gradinariu authored
Add documentation for adis16475 driver which describes the driver device files and shows how the user may use the ABI for various scenarios (configuration, measurement, etc.). Signed-off-by:
Ramona Gradinariu <ramona.gradinariu@analog.com> Link: https://lore.kernel.org/r/20240221085848.991413-4-ramona.gradinariu@analog.comSigned-off-by:
-
Ramona Gradinariu authored
Add documentation for IIO device buffers describing buffer attributes and how data is structured in buffers using scan elements. Signed-off-by:
-
Ramona Gradinariu authored
Refactor index.rst such that it contains a section for generic documentation and a section for Kernel Drivers documentation. Signed-off-by:
-
Dumitru Ceclan authored
This adds support for LTC6373 36 V Fully-Differential Programmable-Gain Instrumentation Amplifier with 25 pA Input Bias Current. The user can program the gain to one of seven available settings through a 3-bit parallel interface (A2 to A0). Signed-off-by:
Dumitru Ceclan <mitrutzceclan@gmail.com> Reviewed-by:
-
Dumitru Ceclan authored
Change the match table to use pointers instead of device ids. Remove type from state as it is not used anymore. Also make the chip_info structures const. Signed-off-by:
-
Dumitru Ceclan authored
Move gain-dB<->code conversion logic from read_raw and write_raw to chip_info callbacks. Signed-off-by:
-
Dumitru Ceclan authored
The LTC6373 is a silicon, 3-bit Fully-Differential digital instrumentation amplifier that supports the following programmable gains (Vout/Vin): G = 0.25, 0.5, 1, 2, 4, 8, 16 + Shutdown. Acked-by:
-
Dumitru Ceclan authored
ADRF5740 and HMC540S have a 4 bit parallel interface. Update ctrl-gpios description and min/maxItems values depending on the matched compatible to correctly reflect the hardware properties. Fixes: 79f2ff64 ("dt-bindings: iio: hmc425a: add entry for ADRF5740 Attenuator") Fixes: 20f87a9a ("dt-bindings: iio: hmc425a: add entry for HMC540S") Acked-by:
-
Josua Mayer authored
HDC2010 and HDC2080 humidity sensors both have an interrupt / data-ready signal which can be used for signaling to the host. Add binding for "interrupts" property so that boards wiring this signal may describe the connection. Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Josua Mayer <josua@solid-run.com> Link: https://lore.kernel.org/r/20240219-iio-hdc20x0-interrupt-binding-v7-1-c8ffb39c3768@solid-run.comSigned-off-by:
-
Thomas Haemmerle authored
Add support to specify the VCC supply which is required to power the device. According the datasheet 7.3.1 Power Up, the device needs 1.5ms after the supply voltage reaches the operating range before the communcation can begin. Signed-off-by:
Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com> Signed-off-by:
Marco Felsch <m.felsch@pengutronix.de> Link: https://lore.kernel.org/r/20240219131114.134607-2-m.felsch@pengutronix.deSigned-off-by:
-
Thomas Haemmerle authored
Add the binding to specify the vcc supply. We can't make it required since this would break the backward compatibility. Reviewed-by:
-
Arturas Moskvinas authored
Use devm_* APIs to enable/disable regulator and to register in IIO infrastructure. Signed-off-by:
Arturas Moskvinas <arturas.moskvinas@gmail.com> Link: https://lore.kernel.org/r/20240219074139.193464-2-arturas.moskvinas@gmail.comSigned-off-by:
-
Sean Rhodes authored
Implement kxj_acpi_orientation to retrieve mount matrix from ACPI ROTM method Cc: Jonathan Cameron <jic23@kernel.org> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de> Signed-off-by:
Sean Rhodes <sean@starlabs.systems> Link: https://lore.kernel.org/r/19d7a10aae5238a2c8db37da1f74edb86480e17e.1708293140.git.sean@starlabs.systemsSigned-off-by:
-
Jonathan Cameron authored
of.h was only included for this definition, so include the correct header instead. Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20240218173323.1023703-9-jic23@kernel.orgSigned-off-by:
-
Jonathan Cameron authored
The only of specific definition used is of_device_id table and that is found in mod_devicetable.h not of.h Reviewed-by:
-
Jonathan Cameron authored
The only of specific definition used is of_device_id table and that is found in mod_devicetable.h not of.h Reviewed-by:
-
Jonathan Cameron authored
The only of specific definition used is of_device_id table and that is found in mod_devicetable.h not of.h Reviewed-by:
-
Jonathan Cameron authored
of.h was only included to get access to this structure, so include the correct header directly instead. Reviewed-by:
-
Jonathan Cameron authored
The only of specific definition used is of_device_id table and that is found in mod_devicetable.h not of.h Reviewed-by:
-
Jonathan Cameron authored
Nothing from linux/of.h used in this driver. Reviewed-by:
-
Jonathan Cameron authored
Nothing from linux/of.h is used in this driver. Reviewed-by:
-
- 25 Feb, 2024 1 commit
-
-
Greg Kroah-Hartman authored
Merge tag 'iio-for-6.9a' of http://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next Jonathan writes: IIO: 1st set of new device support, features and cleanup for 6.9 IIO Backend support =================== New approach from Nuno Sa to the problem of reuse of drivers with IIO devices that are actually the combination of a highspeed chip and an FPGA core handling the data capture and flows. It will hopefully also apply to some other split designs. The ad9467 and axi-adi drivers are converted over to this framework. New device support ================== adi,admfm2000 - New driver for this dual microwave down converter. ams,as73211 - Add support for as7331 UV sensor. richtek,rtq6056 - Add support for related parts RTQ6053 and RTQ6059 st,lsm6dsx - Add ASM330LHHXG1 accelerometer and gyro support (mainly IDs) ti,ads1298 - New driver for this medical ADC. Features ======== tests - Unit tests for the gain-time-scale helper library. bosch,bmi088 - I2C support. bosh,bmi160 - Add 10EC5280 ACPI ID. Used in a number of devices that won't get fixed. The ID is actually a PCI ID belonging to realtech. No response was received to earlier attempts to notify them of this. The manufacturers of some devices have replied to say they will not fix this incorrect ID. Add the ID and hope it isn't a problem. bosch,bmi323 - Add BOSC0200 ACPI ID. Note this is a duplicate of one in the bmc150 driver (it appears these parts share a windows driver). Both drivers perform an ID check that is safe on the other part before successfully probing. hid-sensors-als - Add color temperature and chromaticity support. Note this is a replacement for the series reverted in 6.8 that correctly handles all the potential channel combinations. honeywell,hsc030pa - Triggered buffer support (after driver cleanup). honeywell,mprls00025pa - Improved error handling. - New DT binding to allow use of part number triplet as provided in data sheet to specify equivalent of most of the binding more efficiently. - SPI support. memsic,mxc4005 - ACPI ID MDA6655 as seen in the Chuwi Minibook X 2023 ti,hdc3020 - Add threshold event support (after some driver cleanup) veml,vcnl4000 - Switch to high resolution proximity measurement. Cleanup ======= Various minor typo fixes and better use of defines etc. Treewide - Stop using ACPI_PTR(). The savings in space are small and not worth the complexity of __maybe_unused of ifdef guards. To avoid use in new IIO drivers based on copy and paste, clean it out. - cleanup.h based handling of iio_device_claim_direct_mode()/ iio_device_release_direct_mode() using scope_cond_guard(). In many drivers this is combined with other automated cleanup to give maximum simplifications. An initial set of drivers are converted over to this infrastructure. Tools - Use rewinddir() instead of seekdir() to return to start of file. core - Make iio_bus_type constant. adi,ad16475 - Use irq_get_trigger_type() instead of opencoding. adi,ad16480 - Use irq_get_trigger_type() instead of opencoding. adi,ad-sigma-delta - Avoid overwriting IRQ flags if provided by firmware. ams,as73211 - Use IIO_VAL_FRACTIONAL for scales to simplify the code and potentially improve accuracy. gts-library - Use a div64_u64() instead of a loop to do a division. honeywell,mprls00025pa - Clean up dt-binding doc. - Drop defaults when DT binding not providing values. Very unlikely these were useful given they were wrong for vast majority of supported devices. - Whitespace cleanup miramems,da280 - Use i2c_get_match_data() to replace hand rolled ACPI matching code. semtech,sx9324 - Avoid unnecessary copying of property strings. st,lsm6dsx - Improve docs, particularly wrt to making addition of new device support less noisy. st,lsm9ds0 - Use dev_err_probe() in all probe() error handling. - Improved header includes. - Tidy up termination of ID tables. ti,ads1014 - Correct upper bound on PGA (wrong value had no actual impact) ti,afe4403/4404 - devm_ useage to simplify error handling in probe() and allow() remove to be dropped. voltage-divider - Add dt-binding for io-channel-cells to allow such a device to be both an IIO consumer and IIO producer at the same time. * tag 'iio-for-6.9a' of http://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (106 commits) iio: imu: bmi323: Add ACPI Match Table iio: accel: bmc150: Document duplicate ACPI entries with bmi323 driver iio: adc: ti-ads1298: Add driver dt-bindings: iio: adc: ti-ads1298: Add bindings iio: pressure: hsc030pa add triggered buffer iio: pressure: hsc030pa add mandatory delay iio: pressure: hsc030pa: update datasheet URLs iio: pressure: hsc030pa: include cleanup iio: pressure: hsc030pa: use signed type to hold div_64() result dt-bindings: iio: pressure: honeywell,hsc030pa.yaml add spi props iio: st_sensors: lsm9ds0: Use common style for terminator in ID tables iio: st_sensors: lsm9ds0: Don't use "proxy" headers iio: st_sensors: lsm9ds0: Use dev_err_probe() everywhere iio: adc: adi-axi-adc: move to backend framework iio: adc: ad9467: convert to backend framework iio: add the IIO backend framework iio: buffer-dmaengine: export buffer alloc and free functions of: property: add device link support for io-backends dt-bindings: adc: axi-adc: update bindings for backend framework dt-bindings: adc: ad9467: add new io-backend property ...
-
- 19 Feb, 2024 5 commits
-
-
Jonathan LoBue authored
Adds the ACPI match table for ASUS ROG ALLY to load the bmi323 driver with an ACPI match of "BOSC0200", and a comment about duplicate ACPI identifiers between devices using the bmc150 and bmi323 chips. Reviewed-by:
Luke D. Jones <luke@ljones.dev> Signed-off-by:
Denis Benato <benato.denis96@gmail.com> Signed-off-by:
Antheas Kapenekakis <lkml@antheas.dev> Signed-off-by:
Jonathan LoBue <jlobue10@gmail.com> Tested-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
-
Jonathan LoBue authored
Adds a description of the duplicate ACPI identifier issue between devices using bmc150 and bmi323. Reviewed-by:
-
Mike Looijmans authored
Skeleton driver for the TI ADS1298 medical ADC. This device is typically used for ECG and similar measurements. Supports data acquisition at configurable scale and sampling frequency. Reviewed-by:
-
Mike Looijmans authored
Bindings for the TI ADS1298 medical ADC. This device is typically used for ECG and similar measurements. Supports data acquisition at configurable scale and sampling frequency. The device has so many options for connecting stuff, at this point the bindings aren't nearly complete but partial bindings are better than no bindings at all. Signed-off-by:
-
Petre Rodan authored
Add triggered buffer feature. Signed-off-by:
Petre Rodan <petre.rodan@subdimension.ro> Link: https://lore.kernel.org/r/20240211075645.28777-7-petre.rodan@subdimension.roSigned-off-by:
-
