- 02 May, 2022 13 commits
-
-
Jakub Kicinski authored
The comment next to WIL6210_NAPI_BUDGET says "arbitrary". If we're picking arbitrary values let's pick the recommended default which is NAPI_POLL_WEIGHT. Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220429174643.196994-4-kuba@kernel.org
-
Jakub Kicinski authored
Defining local versions of NAPI_POLL_WEIGHT with the same values in the drivers just makes refactoring harder. Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220429174643.196994-3-kuba@kernel.org
-
Manikanta Pubbisetty authored
WCN6750 is non-DBS 2x2 11AX chipset. Unlike QCA6390 which is a DBS (dual band simultaneous) solution (2 LMACs), WCN6750 has a single LMAC supporting 2G, 5G and 6G bands but will operate only on one band at any given point. WCN6750 is a PCIe based solution, but it is attached to the WPSS (Wireless Processor SubSystem) Q6 processor, hence it is enumerated by the Q6 processor. It is registered to the APSS processor (Application Processor SubSystem) as a platform device(AHB) and remoteproc APIs are used to boot up or shutdown the device like other AHB devices. Also, Device information like BAR and it's size is not known to the APSS processor as the chip is enumerated by WPSS Q6. These details are fetched over QMI. STA and AP modes are supported. Verified basic connectivity and ping in both the modes. An important point to note is that though WCN6750 is a PCIe device, it cannot be attached to any other platform except on Qualcomm Snapdragon SoCs due to the aforementioned reasons. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220429170502.20080-10-quic_mpubbise@quicinc.com
-
Manikanta Pubbisetty authored
HAL RX descriptor for WCN6750 is same as QCN9074, this means that the size of the HAL RX decriptor and the DP APIs that WCN6750 requires to enable datapath should be initialized with that of QCN9074's RX descriptor size and the DP APIs respectively. There is one change wrt to REO configuration though, REO configuration for WCN6750 follows WCN6855, therefore use reo_setup() of WCN6855 for WCN6750. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220429170502.20080-9-quic_mpubbise@quicinc.com
-
Manikanta Pubbisetty authored
Add HAL changes required to support WCN6750. Offsets of some registers for WCN6750 are different from other supported devices; move such register offsets to platform specific ath11k_hw_regs. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220429170502.20080-8-quic_mpubbise@quicinc.com
-
Manikanta Pubbisetty authored
In the case of WCN6750, FW doesn't request for DDR memory via QMI, instead it uses a fixed 12MB reserved Memory region in the DDR which is called as MSA region. As a result, QMI message sequence is not same as other ath11k supported devices. Also, M3 firmware will be bundled into the FW and will be downloaded to the target as part of Q6 boot. This is the QMI flow in the case of WCN6750, 1) QMI firmware indication REQ/RESP 2) QMI host capability REQ/RESP 3) QMI target capability REQ/RESP 4) QMI device info REQ/RESP 5) QMI BDF download 6) QMI FW ready Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220429170502.20080-7-quic_mpubbise@quicinc.com
-
Manikanta Pubbisetty authored
Since WPPS Q6 does the PCIe enumeration of WCN6750, device information like BAR and BAR size is not known to the APPS processor (Application Processor SubSystem). In order to fetch these details, a QMI message called device info request will be sent to the target. Therefore, add logic to fetch BAR details from the target. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220429170502.20080-6-quic_mpubbise@quicinc.com
-
Manikanta Pubbisetty authored
WCN6750 uses static window mapping to access the HW registers. Unlike QCN9074 which uses 3rd window for UMAC and 2nd window for CE register access, WCN6750 uses 1st window for UMAC and 2nd window for CE registers. Also, refactor the code so that WCN6750 can use the existing ath11k_pci_read32/write32() APIs for accessing the registers. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220429170502.20080-5-quic_mpubbise@quicinc.com
-
Manikanta Pubbisetty authored
WCN6750 is a PCIe based solution that is attached to and enumerated by the WPSS (Wireless Processor SubSystem) Q6 processor. Though it is a PCIe device, since it is not attached to APSS processor (Application Processor SubSystem), APSS will be unaware of such a decice and hence it is registered to the APSS processor as a platform device(AHB). Because of this hybrid nature, it is called as a hybrid bus device. A new variable hybrid_bus_type is defined in hw_params to indicate the hybrid nature of the device. Add HW params for WCN6750. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220429170502.20080-4-quic_mpubbise@quicinc.com
-
Manikanta Pubbisetty authored
In ath11k, bus_params were added with an intention to hold parameters related to bus (AHB/PCI), but this is not true as some bus parameters being different between chipsets of the same bus. With the addition of WCN6750 to ath11k, bus parameters are going to be entirely different among AHB devices. Therefore, it is wise to move bus_params to hw_params and get rid of bus_params entirely. Also, mhi_support parameter is not used anywhere in the driver, remove it from bus_params. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220429170502.20080-3-quic_mpubbise@quicinc.com
-
Manikanta Pubbisetty authored
WCN6750 is the WLAN chip on Qualcomm Snapdragon SoC SC7280; Though being a PCIe based solution, it is not attached to the APSS processor (Application Processor SubSystem), it is instead attached to another tiny processor called WPSS Q6 processor (Wireless Processor SubSystem) on the SC7280 MSM, where the WLAN firmware runs, and it is the WLAN firmware running on the Q6 processor which enumerates WCN6750, as a result APPS processor would never know such a device being present in the system and would not detect the WCN6750 hardware unless and otherwise WCN6750 is registered as a platform device. This is the reason behind adding WCN6750 WLAN node in the device tree. Add WCN6750 wireless driver support, its based on ath11k driver. Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220429170502.20080-2-quic_mpubbise@quicinc.com
-
Wen Gong authored
In the phase of wlan load, it has hw scan and 11d scan which sent to firmware by ath11k, then hw scan and 11d scan will use about 14 seconds, and meanwhile ath11k_reg_update_chan_list() is running in workqueue of ath11k_base, and wait for 11d scan/hw scan finished. When the hw scan finished, mac80211 will start to connect and send management packet, at this moment, ath11k_reg_update_chan_list() is still waiting for 11d scan finished, so wmi_mgmt_tx_work of ath11k will not run and thus the tx management packet also not send out and lead authentication timed out. log: INFO kernel: [ 187.885322] wlan0: authenticate with 72:6c:57:43:9f:90 INFO kernel: [ 187.937266] wlan0: send auth to 72:6c:57:43:9f:90 (try 1/3) INFO kernel: [ 188.626944] wlan0: send auth to 72:6c:57:43:9f:90 (try 2/3) INFO kernel: [ 189.650999] wlan0: send auth to 72:6c:57:43:9f:90 (try 3/3) INFO kernel: [ 190.651917] wlan0: authentication with 72:6c:57:43:9f:90 timed out Change wmi_mgmt_tx_work to another queue workqueue_aux of ath11k_base, then connection success. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3 Signed-off-by:
Wen Gong <quic_wgong@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220428023320.4007-1-quic_wgong@quicinc.com
-
Wen Gong authored
When test connect/disconnect to an AP frequently with WCN6855, sometimes it show below log. [ 277.040121] wls1: deauthenticating from 8c:21:0a:b3:5a:64 by local choice (Reason: 3=DEAUTH_LEAVING) [ 277.050906] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11 [ 277.050944] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif pK-error [ 277.050954] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64 [ 277.050961] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71 [ 277.050967] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71 [ 277.050976] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11 [ 277.050983] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif pK-error [ 277.050989] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64 [ 277.050995] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71 [ 277.051000] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71 [ 278.064050] ath11k_pci 0000:05:00.0: failed to request fw stats: -110 Reason is: When running disconnect operation, sta_info removed from local->sta_hash by __sta_info_destroy_part1() from __sta_info_flush(), after this, ieee80211_find_sta_by_ifaddr() which called by ath11k_wmi_tlv_fw_stats_data_parse() and ath11k_wmi_tlv_rssi_chain_parse() cannot find this station, then failed log printed. steps are like this: 1. when disconnect from AP, __sta_info_destroy() called __sta_info_destroy_part1() and __sta_info_destroy_part2(). 2. in __sta_info_destroy_part1(), it has "sta_info_hash_del(local, sta)" and "list_del_rcu(&sta->list)", it will remove the ieee80211_sta from the list of ieee80211_hw. 3. in __sta_info_destroy_part2(), it called drv_sta_state()->ath11k_mac_op_sta_state(), then peer->sta is clear at this moment. 4. in __sta_info_destroy_part2(), it then called sta_set_sinfo()->drv_sta_statistics() ->ath11k_mac_op_sta_statistics(), then WMI_REQUEST_STATS_CMDID sent to firmware. 5. WMI_UPDATE_STATS_EVENTID reported from firmware, at this moment, the ieee80211_sta can not be found again because it has remove from list in step2 and also peer->sta is clear in step3. 6. in __sta_info_destroy_part2(), it then called cleanup_single_sta()-> sta_info_free()->kfree(sta), at this moment, the ieee80211_sta is freed in memory, then the failed log will not happen because function ath11k_mac_op_sta_state() will not be called. Actually this print log is not a real error, it is only to skip parse the info, so change to skip print by default debug setting. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3 Signed-off-by:
Wen Gong <quic_wgong@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220428022426.2927-1-quic_wgong@quicinc.com
-
- 29 Apr, 2022 3 commits
-
-
Baochen Qiang authored
We are seeing below warning: ... kernel: [ 5720.362941] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:197 kernel: [ 5720.362943] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 0, name: swapper/4 kernel: [ 5720.362947] CPU: 4 PID: 0 Comm: swapper/4 Tainted: G W 5.10.90 #18 4fa489e3e5c16043994f416310c2f60eff666320 kernel: [ 5720.362949] Hardware name: Google Nipperkin/Nipperkin, BIOS Google_Nipperkin.14316.0.0 10/30/2021 kernel: [ 5720.362950] Call Trace: kernel: [ 5720.362953] <IRQ> kernel: [ 5720.362959] dump_stack+0x9c/0xe7 kernel: [ 5720.362964] ___might_sleep+0x14a/0x160 kernel: [ 5720.362967] kmem_cache_alloc+0x46/0x226 kernel: [ 5720.362970] ? __alloc_skb+0x6c/0x19e kernel: [ 5720.362972] __alloc_skb+0x6c/0x19e kernel: [ 5720.362985] cfg80211_gtk_rekey_notify+0xa2/0x21d [cfg80211 2c8b5aee0416e7d010d70c332a47990fc843c1c5] kernel: [ 5720.362995] ath11k_wmi_gtk_offload_status_event+0x102/0x155 [ath11k 4c6bb5f7331c81199d56a7e37bdc10030f167838] kernel: [ 5720.363002] ath11k_wmi_tlv_op_rx+0x301/0x51b [ath11k 4c6bb5f7331c81199d56a7e37bdc10030f167838] kernel: [ 5720.363009] ath11k_htc_rx_completion_handler+0xee/0x3f5 [ath11k 4c6bb5f7331c81199d56a7e37bdc10030f167838] kernel: [ 5720.363017] ath11k_ce_per_engine_service+0x2aa/0x32c [ath11k 4c6bb5f7331c81199d56a7e37bdc10030f167838] kernel: [ 5720.363024] ath11k_pci_ce_tasklet+0x1a/0x30 [ath11k_pci 9acc399855ea172aa14a892c0bfdba0ce22d6f07] kernel: [ 5720.363028] tasklet_action_common+0x8d/0x9f kernel: [ 5720.363032] __do_softirq+0x163/0x29a kernel: [ 5720.363035] asm_call_irq_on_stack+0x12/0x20 kernel: [ 5720.363037] </IRQ> kernel: [ 5720.363041] do_softirq_own_stack+0x3c/0x48 kernel: [ 5720.363043] __irq_exit_rcu+0x9b/0x9d kernel: [ 5720.363046] common_interrupt+0xc9/0x14d kernel: [ 5720.363049] asm_common_interrupt+0x1e/0x40 kernel: [ 5720.363054] RIP: 0010:cpuidle_enter_state+0x1c5/0x2ac kernel: [ 5720.363056] Code: 84 f6 4c 8b 75 c0 74 1e 48 c7 45 c8 00 00 00 00 9c 8f 45 c8 0f ba 65 c8 09 0f 82 d1 00 00 00 31 ff e8 4a bb 6c ff fb 45 85 e4 <78> 47 44 89 e0 48 6b d0 68 49 8b 4c 16 48 48 2b 5d b8 49 89 5d 18 kernel: [ 5720.363058] RSP: 0018:ffffa7e640157e78 EFLAGS: 00000206 kernel: [ 5720.363060] RAX: ffff9807ddf29b40 RBX: 00000533e033584c RCX: 00000533e033584c kernel: [ 5720.363062] RDX: 0000000000000004 RSI: 0000000000000000 RDI: 0000000000000000 kernel: [ 5720.363063] RBP: ffffa7e640157ec0 R08: 0000000000000002 R09: 00000533e171bb7a kernel: [ 5720.363064] R10: 0000000000000900 R11: fffffffffffffffe R12: 0000000000000003 kernel: [ 5720.363065] R13: ffff9804c2ef6000 R14: ffffffffbe9a7bd0 R15: 0000000000000003 kernel: [ 5720.363069] ? cpuidle_enter_state+0x19a/0x2ac kernel: [ 5720.363072] cpuidle_enter+0x2e/0x3d kernel: [ 5720.363074] do_idle+0x163/0x1ee kernel: [ 5720.363076] cpu_startup_entry+0x1d/0x1f kernel: [ 5720.363078] secondary_startup_64_no_verify+0xb1/0xbb ... This is because GFP_KERNEL is used by ath11k_wmi_gtk_offload_status_event while in atomic context. Fix it by using GFP_ATOMIC instead. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3 Fixes: a16d9b50 ("ath11k: support GTK rekey offload") Signed-off-by:
Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220427120033.1046759-1-quic_bqiang@quicinc.com
-
Abhishek Kumar authored
Double free crash is observed when FW recovery(caused by wmi timeout/crash) is followed by immediate suspend event. The FW recovery is triggered by ath10k_core_restart() which calls driver clean up via ath10k_halt(). When the suspend event occurs between the FW recovery, the restart worker thread is put into frozen state until suspend completes. The suspend event triggers ath10k_stop() which again triggers ath10k_halt() The double invocation of ath10k_halt() causes ath10k_htt_rx_free() to be called twice(Note: ath10k_htt_rx_alloc was not called by restart worker thread because of its frozen state), causing the crash. To fix this, during the suspend flow, skip call to ath10k_halt() in ath10k_stop() when the current driver state is ATH10K_STATE_RESTARTING. Also, for driver state ATH10K_STATE_RESTARTING, call ath10k_wait_for_suspend() in ath10k_stop(). This is because call to ath10k_wait_for_suspend() is skipped later in [ath10k_halt() > ath10k_core_stop()] for the driver state ATH10K_STATE_RESTARTING. The frozen restart worker thread will be cancelled during resume when the device comes out of suspend. Below is the crash stack for reference: [ 428.469167] ------------[ cut here ]------------ [ 428.469180] kernel BUG at mm/slub.c:4150! [ 428.469193] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI [ 428.469219] Workqueue: events_unbound async_run_entry_fn [ 428.469230] RIP: 0010:kfree+0x319/0x31b [ 428.469241] RSP: 0018:ffffa1fac015fc30 EFLAGS: 00010246 [ 428.469247] RAX: ffffedb10419d108 RBX: ffff8c05262b0000 [ 428.469252] RDX: ffff8c04a8c07000 RSI: 0000000000000000 [ 428.469256] RBP: ffffa1fac015fc78 R08: 0000000000000000 [ 428.469276] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 428.469285] Call Trace: [ 428.469295] ? dma_free_attrs+0x5f/0x7d [ 428.469320] ath10k_core_stop+0x5b/0x6f [ 428.469336] ath10k_halt+0x126/0x177 [ 428.469352] ath10k_stop+0x41/0x7e [ 428.469387] drv_stop+0x88/0x10e [ 428.469410] __ieee80211_suspend+0x297/0x411 [ 428.469441] rdev_suspend+0x6e/0xd0 [ 428.469462] wiphy_suspend+0xb1/0x105 [ 428.469483] ? name_show+0x2d/0x2d [ 428.469490] dpm_run_callback+0x8c/0x126 [ 428.469511] ? name_show+0x2d/0x2d [ 428.469517] __device_suspend+0x2e7/0x41b [ 428.469523] async_suspend+0x1f/0x93 [ 428.469529] async_run_entry_fn+0x3d/0xd1 [ 428.469535] process_one_work+0x1b1/0x329 [ 428.469541] worker_thread+0x213/0x372 [ 428.469547] kthread+0x150/0x15f [ 428.469552] ? pr_cont_work+0x58/0x58 [ 428.469558] ? kthread_blkcg+0x31/0x31 Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1 Co-developed-by:
Wen Gong <quic_wgong@quicinc.com> Signed-off-by:
Wen Gong <quic_wgong@quicinc.com> Signed-off-by:
Abhishek Kumar <kuabhs@chromium.org> Reviewed-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220426221859.v2.1.I650b809482e1af8d0156ed88b5dc2677a0711d46@changeid
-
Wan Jiabing authored
Use if and else instead of if(A) and if (!A). Signed-off-by:
Wan Jiabing <wanjiabing@vivo.com> Acked-by:
Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220424094441.104937-1-wanjiabing@vivo.com
-
- 27 Apr, 2022 7 commits
-
-
Wan Jiabing authored
Use if and else instead of if(A) and if (!A). Signed-off-by:
Wan Jiabing <wanjiabing@vivo.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220424094552.105466-1-wanjiabing@vivo.com
-
Wan Jiabing authored
Use if and else instead of if(A) and if (!A). Signed-off-by:
Wan Jiabing <wanjiabing@vivo.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220424094522.105262-1-wanjiabing@vivo.com
-
Wen Gong authored
This read the country code from SMBIOS and send the country code to firmware, firmware will indicate the regulatory domain info of the country code and then ath11k will use the info. dmesg: [ 1242.637173] ath11k_pci 0000:02:00.0: chip_id 0x2 chip_family 0xb board_id 0xff soc_id 0x400c0200 [ 1242.637176] ath11k_pci 0000:02:00.0: fw_version 0x110b09e5 fw_build_timestamp 2021-06-22 09:32 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HSP.1.1-02533-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 [ 1242.637253] ath11k_pci 0000:02:00.0: worldwide regdomain setting from SMBIOS [ 1242.637259] ath11k_pci 0000:02:00.0: bdf variant name not found. [ 1242.637261] ath11k_pci 0000:02:00.0: SMBIOS bdf variant name not set. [ 1242.637263] ath11k_pci 0000:02:00.0: DT bdf variant name not set. [ 1242.927543] ath11k_pci 0000:02:00.0: set current country pdev id 0 alpha2 00 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3 Signed-off-by:
Wen Gong <quic_wgong@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220421023501.32167-1-quic_wgong@quicinc.com
-
Hari Chandrakanthan authored
When ath11k modules are removed using rmmod with spectral scan enabled, crash is observed. Different crash trace is observed for each crash. Send spectral scan disable WMI command to firmware before cleaning the spectral dbring in the spectral_deinit API to avoid this crash. call trace from one of the crash observed: [ 1252.880802] Unable to handle kernel NULL pointer dereference at virtual address 00000008 [ 1252.882722] pgd = 0f42e886 [ 1252.890955] [00000008] *pgd=00000000 [ 1252.893478] Internal error: Oops: 5 [#1] PREEMPT SMP ARM [ 1253.093035] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.89 #0 [ 1253.115261] Hardware name: Generic DT based system [ 1253.121149] PC is at ath11k_spectral_process_data+0x434/0x574 [ath11k] [ 1253.125940] LR is at 0x88e31017 [ 1253.132448] pc : [<7f9387b8>] lr : [<88e31017>] psr: a0000193 [ 1253.135488] sp : 80d01bc8 ip : 00000001 fp : 970e0000 [ 1253.141737] r10: 88e31000 r9 : 970ec000 r8 : 00000080 [ 1253.146946] r7 : 94734040 r6 : a0000113 r5 : 00000057 r4 : 00000000 [ 1253.152159] r3 : e18cb694 r2 : 00000217 r1 : 1df1f000 r0 : 00000001 [ 1253.158755] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user [ 1253.165266] Control: 10c0383d Table: 5e71006a DAC: 00000055 [ 1253.172472] Process swapper/0 (pid: 0, stack limit = 0x60870141) [ 1253.458055] [<7f9387b8>] (ath11k_spectral_process_data [ath11k]) from [<7f917fdc>] (ath11k_dbring_buffer_release_event+0x214/0x2e4 [ath11k]) [ 1253.466139] [<7f917fdc>] (ath11k_dbring_buffer_release_event [ath11k]) from [<7f8ea3c4>] (ath11k_wmi_tlv_op_rx+0x1840/0x29cc [ath11k]) [ 1253.478807] [<7f8ea3c4>] (ath11k_wmi_tlv_op_rx [ath11k]) from [<7f8fe868>] (ath11k_htc_rx_completion_handler+0x180/0x4e0 [ath11k]) [ 1253.490699] [<7f8fe868>] (ath11k_htc_rx_completion_handler [ath11k]) from [<7f91308c>] (ath11k_ce_per_engine_service+0x2c4/0x3b4 [ath11k]) [ 1253.502386] [<7f91308c>] (ath11k_ce_per_engine_service [ath11k]) from [<7f9a4198>] (ath11k_pci_ce_tasklet+0x28/0x80 [ath11k_pci]) [ 1253.514811] [<7f9a4198>] (ath11k_pci_ce_tasklet [ath11k_pci]) from [<8032227c>] (tasklet_action_common.constprop.2+0x64/0xe8) [ 1253.526476] [<8032227c>] (tasklet_action_common.constprop.2) from [<803021e8>] (__do_softirq+0x130/0x2d0) [ 1253.537756] [<803021e8>] (__do_softirq) from [<80322610>] (irq_exit+0xcc/0xe8) [ 1253.547304] [<80322610>] (irq_exit) from [<8036a4a4>] (__handle_domain_irq+0x60/0xb4) [ 1253.554428] [<8036a4a4>] (__handle_domain_irq) from [<805eb348>] (gic_handle_irq+0x4c/0x90) [ 1253.562321] [<805eb348>] (gic_handle_irq) from [<80301a78>] (__irq_svc+0x58/0x8c) Tested-on: QCN6122 hw1.0 AHB WLAN.HK.2.6.0.1-00851-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Hari Chandrakanthan <quic_haric@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/1649396345-349-1-git-send-email-quic_haric@quicinc.com
-
Manikanta Pubbisetty authored
Currently, WBM idle ring HP is updated much before the shadow configuration is sent to the FW. Any update to the shadow registers before FW mode on request would not be reflected on to the actual HW registers failing to bring up the device. Send FW mode ON QMI request before WBM idle ring HP update to fix this problem. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220406094107.17878-12-quic_mpubbise@quicinc.com
-
Manikanta Pubbisetty authored
WCN6750 is a single PDEV non-DBS chip which supports 2G, 5G and 6G bands. It is a single LMAC device which can be either hooked to 2G/5G/6G bands. Add WMI changes to support WCN6750. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220406094107.17878-11-quic_mpubbise@quicinc.com
-
Manikanta Pubbisetty authored
Though WCN6750 is a single PDEV device, it is not a DBS solution. So, do not put HW in DBS mode for WCN6750. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Signed-off-by:
Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220406094107.17878-10-quic_mpubbise@quicinc.com
-
- 23 Apr, 2022 7 commits
-
-
Thibaut VARÈNE authored
This patch fixes an invalid TX PA DC bias level on QCA9561, which results in a very low output power and very low throughput as devices are further away from the AP (compared to other 2.4GHz APs). This patch was suggested by Felix Fietkau, who noted[1]: "The value written to that register is wrong, because while the mask definition AR_CH0_TOP2_XPABIASLVL uses a different value for 9561, the shift definition AR_CH0_TOP2_XPABIASLVL_S is hardcoded to 12, which is wrong for 9561." In real life testing, without this patch the 2.4GHz throughput on Yuncore XD3200 is around 10Mbps sitting next to the AP, and closer to practical maximum with the patch applied. [1] https://lore.kernel.org/all/91c58969-c60e-2f41-00ac-737786d435ae@nbd.nameSigned-off-by:
Thibaut VARÈNE <hacks+kernel@slashdirt.org> Acked-by:
Felix Fietkau <nbd@nbd.name> Acked-by:
Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220417145145.1847-1-hacks+kernel@slashdirt.org
-
Dan Carpenter authored
The "rxstatus->rs_keyix" eventually gets passed to test_bit() so we need to ensure that it is within the bitmap. drivers/net/wireless/ath/ath9k/common.c:46 ath9k_cmn_rx_accept() error: passing untrusted data 'rx_stats->rs_keyix' to 'test_bit()' Fixes: 4ed1a8d4 ("ath9k_htc: use ath9k_cmn_rx_accept") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220409061225.GA5447@kili
-
Minghao Chi authored
Using pm_runtime_resume_and_get() is more appropriate for simplifing code. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Minghao Chi <chi.minghao@zte.com.cn> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220411013602.2517086-1-chi.minghao@zte.com.cn
-
YueHaibing authored
drivers/net/wireless/ath/ath11k/mac.c:8175:13: error: ‘ath11k_mac_op_ipv6_changed’ defined but not used [-Werror=unused-function] static void ath11k_mac_op_ipv6_changed(struct ieee80211_hw *hw, ^~~~~~~~~~~~~~~~~~~~~~~~~~ Wrap it with #ifdef block to fix this. Fixes: c3c36bfe ("ath11k: support ARP and NS offload") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220411020843.10284-1-yuehaibing@huawei.com
-
Yang Yingliang authored
Add the missing unlock before return from function ath11k_wow_op_resume() in the error handling case. Fixes: 90bf5c8d ("ath11k: purge rx pktlog when entering WoW") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220408030912.3087293-1-yangyingliang@huawei.com
-
Baochen Qiang authored
Add ath11k_mac_op_set_bios_sar_specs() to ath11k_ops, this function is called when user space application calls NL80211_CMD_SET_SAR_SPECS. ath11k also registers SAR type and frequency ranges to wiphy so user space can query SAR capabilities. This feature is currently enabled for WCN6855. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220401120948.1312956-3-quic_bqiang@quicinc.com
-
Wen Gong authored
When the WMI service bits are reported from firmware they are divided into multiple segments, with 128 bits in each segment. The first segment is processed by ath11k_wmi_service_bitmap_copy(), the second segment is processed by ath11k_service_available_event() with WMI_TAG_SERVICE_AVAILABLE_EVENT. When the service bit exceed 256 bits, then firmware reports it by tag WMI_TAG_ARRAY_UINT32 in WMI_SERVICE_AVAILABLE_EVENTID. Currently ath11k does not process the third segment. Upcoming features need to know if firmware support is available for the features, so add processing of the third segment. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by:
Wen Gong <quic_wgong@quicinc.com> Signed-off-by:
Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220401120948.1312956-2-quic_bqiang@quicinc.com
-
- 12 Apr, 2022 4 commits
-
-
Yang Li authored
The print function dev_err() is redundant because platform_get_irq_byname() already prints an error. Eliminate the follow coccicheck warning: ./drivers/net/wireless/ath/ath9k/ahb.c:103:2-9: line 103 is redundant because platform_get_irq() already prints an error Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Yang Li <yang.lee@linux.alibaba.com> Acked-by:
Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220408000113.129906-2-yang.lee@linux.alibaba.com
-
Yang Li authored
Eliminate the follow smatch warning: drivers/net/wireless/ath/wcn36xx/smd.c:3151 wcn36xx_smd_gtk_offload_get_info_rsp() warn: inconsistent indenting Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Yang Li <yang.lee@linux.alibaba.com> Acked-by:
Loic Poulain <loic.poulain@linaro.org> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220408000113.129906-1-yang.lee@linux.alibaba.com
-
Colin Ian King authored
There is a spelling mistake in an ath11k_warn message. Fix it. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220407102820.613881-1-colin.i.king@gmail.com
-
Peter Seiderer authored
Stop reading (and copying) from ieee80211_tx_rate to ath_tx_info.rates after list end tag (count == 0, idx < 0), prevents copying of garbage to card registers. Note: no need to write to the remaining ath_tx_info.rates entries as the complete ath_tx_info struct is already initialized to zero from both call sites. Signed-off-by:
Peter Seiderer <ps.report@gmx.net> Acked-by:
Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220402153014.31332-1-ps.report@gmx.net
-
- 06 Apr, 2022 6 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.19. Major changes: ath11k * Wake-on-WLAN support for QCA6390 and WCN6855 * device recovery (firmware restart) support for QCA6390 and WCN6855 wcn36xx * support for transmit rate reporting to user space
-
Kalle Valo authored
No need to have goto for a return statement, so simplify the code. While at it, print warning messages if power up calls fail. No functional changes. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220401173042.17467-4-kvalo@kernel.org
-
Kalle Valo authored
While reviewing the mhi.c I noticed we were just ignoring the errors coming from MHI subsystem during suspend and resume. Add proper checks and warning messages. Also pass the error value to callers. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220401173042.17467-3-kvalo@kernel.org
-
Kalle Valo authored
State machines are difficult to understand and in this case it's just useless, which is shown by the diffstat. So remove it entirely to make the code simpler. No functional changes. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Signed-off-by:
Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220401173042.17467-2-kvalo@kernel.org
-
Ping-Ke Shih authored
The smatch reports: rtw8852a.c:1857 rtw8852a_btc_set_wl_txpwr_ctrl() error: uninitialized symbol '_cur'. rtw8852a.c:1858 rtw8852a_btc_set_wl_txpwr_ctrl() error: uninitialized symbol '_cur'. This is because rtw89_mac_txpwr_read32() can possibly return before setting argument _cur, and the caller will use the uninitialized value. To fix this problem, check the return value of rtw89_mac_txpwr_read32(). Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220318035202.42437-1-pkshih@realtek.com
-
Ping-Ke Shih authored
8852C uses different fields to represent RX bandwidth. Since other fields are the same, I check chip_id to get bandwidth instead of creating another v1 function. Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220318023214.32411-12-pkshih@realtek.com
-