One crtc can use two komeda_pipeline, and one works as master and as
slave. the slave pipeline doesn't have its own output and timing
ctrlr, but pre-composite the input layer data flow and then feed the
result to master. the pipeline configuration like:

slave-layer-0 \
...            slave->CU
slave-layer-4 /         \
                        \
master-layer-0 --------> master->CU -> ...
 ...                  /
master-layer-4 ------>

Since komeda Compiz doesn't output alpha, so the slave->CU result
only can be used as bottom input when blend it with master input data
flows.
Signed-off-by: Lowry Li (Arm Technology China) <lowry.li@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Komeda supports two types of layer split:
- none-scaling split
- scaling split
Since D71 merger only support scaler as input, so for none-scaling split,
the two layer dflow will be output to compiz directly. for scaling_split,
the data flow will be merged by merger firstly, then output the merged
data flow to compiz.

Komeda handles the split in kernel completely to hide the detailed and
complicated split calcualtion to user mode, for user only need to set the
layer_split property to enable/disable it.

v2: Rebase
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

To achieve same caling effect compare with none split, the texel
calculation need to use the same scaling ratio before split, so add
"total_xxx" to pipeline to describe the hsize/vsize before split.
Update pipeline and d71_scaler_update accordingly.

v2: Rebase and addressed Liviu's comments
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Introduce a new component komeda_merger, because D71 HW supports to split
a whole image to two half parts and does the scaling independently. Merger
merges two separate results to one, and output it to compositor or wb_layer
For this patch:
- Add the definition of komeda_merger/merger_state
- Report and initialize komeda_merger according to the D71 HW.

v2: Rebase
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Current komeda driver uses three dedicated clks for a specific purpose:
- mclk: main engine clock
- pclk: APB clock
- pipeline->aclk: AXI clock.

But per spec the komeda HW only has three input clks:
- ACLK: used for AXI masters, APB slave and most pipeline processing
- PXCLK for pipeline 0: output pixel clock for pipeline 0
- PXCLK for pipeline 1: output pixel clock for pipeline 1

So one ACLK is enough, no need to split it to three mclk/pclk/axiclk.
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

To avoid confusion, unify the driver main engine clk name "mclk" to
the spec name "aclk".
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Current komeda driver uses three dedicated clks for a specific purpose:
- mclk: main engine clock
- pclk: APB clock
- pipeline->aclk: AXI clock.

But per spec the komeda HW only has three input clks:
- ACLK: used for AXI masters, APB slave and most pipeline processing
- PXCLK for pipeline 0: output pixel clock for pipeline 0
- PXCLK for pipeline 1: output pixel clock for pipeline 1

So one ACLK is enough, no need to split it to three mclk/pclk/axiclk.
drop pclk/pipeline->axiclk. but only keep one mclk in komeda driver.
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

- Creates the zpos property.
- Implement komeda_crtc_normalize_zpos to replace
drm_atomic_normalize_zpos, reasons as the following:

1. The drm_atomic_normalize_zpos allows to configure same zpos for
different planes, but komeda doesn't support such configuration.
2. For further slave pipline case, Komeda need to calculate the
max_slave_zorder, we will merge such calculation into
komed_crtc_normalize_zpos to save a separated plane_state loop.
3. For feature none-scaling layer_split, which a plane_state will be
assigned to two individual layers(left/right), which requires two
normalize_zpos for this plane, plane_st->normalize_zpos will be used
by left layer, normalize_zpos + 1 for right_layer.

This patch series depends on:
- https://patchwork.freedesktop.org/series/58710/
- https://patchwork.freedesktop.org/series/59000/
- https://patchwork.freedesktop.org/series/59002/
- https://patchwork.freedesktop.org/series/59747/
- https://patchwork.freedesktop.org/series/59915/
- https://patchwork.freedesktop.org/series/60083/
- https://patchwork.freedesktop.org/series/60698/Signed-off-by: Lowry Li (Arm Technology China) <lowry.li@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

- Y0L2 and P010 are block (tiled) format, Update the kemeda logic to
compatible with such block format.
- Since DRM introduced a general block information to drm_format_info,
  the format_caps->tiled_size no long needed, delete it.
- Build some fb utils functions for code sharing.
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Add komeda_fb_check_src_coords and check if the layer configured src
rect can meet the requirement of fb and fb format.
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Updates the device-tree doc about how to enable SMMU by devicetree.
Signed-off-by: Lowry Li (Arm Technology China) <lowry.li@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Adds iommu_connect and disconnect for SMMU support, and configures
TBU translation once SMMU has been attached to the display device.
Signed-off-by: Lowry Li (Arm Technology China) <lowry.li@arm.com>
[fixed checking of error code returned by dp_wait_cond() and removed
extraneous DRM_ERROR() calls]
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Adds color-encoding properties if layer can support YUV format.
Updates HW YUV-RGB matrix state according to the color-encoding
properties.
Signed-off-by: Lowry Li (Arm Technology China) <lowry.li@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Updates HW up-sampling method according to the format type.
Signed-off-by: Lowry Li (Arm Technology China) <lowry.li@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Komeda series hardware doesn't support Rot90 for AFBC wide block. So
add limitation check to reject it if such configuration has been posted.
Signed-off-by: Lowry Li (Arm Technology China) <lowry.li@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

- Adds rotation property to plane.
- Komeda display rotation support diverges from the specific formats,
so need to check the user required rotation type with the format caps
and reject the commit if it can not be supported.
- In the layer validate flow, sets the rotation value to the layer
state. If r90 or r270, swap the width and height of the data flow
for next stage.
Signed-off-by: Lowry Li (Arm Technology China) <lowry.li@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Besides clearing the input ID to zero, D71 compiz also has input
enable bit in CU_INPUTx_CONTROL which need to be cleared.
Signed-off-by: Lowry Li (Arm Technology China) <lowry.li@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

dp_wait_cond() currently returns the number of retries left over which
is hardly an useful information. Convert to returning -ETIMEDOUT when
the wait times out, or 0 (zero) when condition is met before deadline.

Also convert the users of the function to return the error value.
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>

Creates plane alpha and blend mode properties attached to plane.

This patch depends on:
- https://patchwork.freedesktop.org/series/59915/
- https://patchwork.freedesktop.org/series/58665/
- https://patchwork.freedesktop.org/series/59000/
- https://patchwork.freedesktop.org/series/59002/
- https://patchwork.freedesktop.org/series/59471/

Changes since v1:
- Adds patch denpendency in the comment

Changes since v2:
- Remove [RFC] from the subject

Changes since v3:
- Rebase the code
Signed-off-by: Lowry Li (Arm Technology China) <lowry.li@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Besides scaling, Arm display scaler also can support image enhancement.
For support it, Add a new property "img_enhancement" to plane, then user
can turn on/off it by this property, and kernel follow user's requirement
to maitain the state and enable/disable the real HW image enhancement.

v2: Rebase and rename "needs_img_enhancement" to "en_img_enhancement"
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

For downscaling there is a restriction, the downscaling needed engine
clock can not acceed the real engine clock, and the clock requirement
mostly depend on the specific HW, to solve this problem:
1. Add a pipeline func - downscaling_clk_check for CORE to query the real
   HW if downscaling can be supported.
2. Add new property clock ratio which is the ratio of:
     (mclk << 32) / pxlclk
   then User driver can use this ratio to do the clock check to avoid post
   an invalid downscaling to kernel.

v2: Rebase and Delete debug print
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

1. Add scaler to writeback pipeline to enable the writeback scaling support
2. Display HW can not do upscaling for writeback, check it when validate.

v2: Rebase
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

1. Add scaler component and initialize it according to D71 HW.
2. Implement d71_scaler_update/disable/dump

v2:
- Correct a typo
- Constify component_funcs: d71_scaler_funcs
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

This patch add the initial and necessary logic for CORE to support scaler:
- Complete the struct komeda_scaler and komeda_scaler_state for adding
  the scaler specific features and capablities.
- Implement komeda_scaler_validate to check the scaler with the data flow
  configurations.
- Enable scaling support for plane input path (layer input data flow).

v2: Fix a typo, and rename "needs_scaling" to "en_scaling"
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

According to the komeda pipeline configuration, attach scaler to drm as
private object.

v2: Rebase
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

For supporting AFBC:
1. Check if the user requested modifier can be supported by display HW.
2. Check the obj->size with AFBC's requirement.
3. Configure HW according to the modifier (afbc features)

This patch depends on:
- https://patchwork.freedesktop.org/series/59915/
- https://patchwork.freedesktop.org/series/59000/

v2: Rebase and addressed Ayan's comments
Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Komeda driver uses a individual component to describe the HW's writeback
caps, but drivers doesn't define a new structure and still uses the
existing "struct komeda_layer" to describe this new component.
The detailed changes as follow:

1. Initialize wb_layer according to HW and report it to CORE.
2. CORE exposes wb_layer as a resource to KMS by private_obj.
3. Report writeback supporting by add a wb_connector to KMS, and then
   wb_connector will take act as a component resources user,
   so the func komeda_wb_encoder_atomic_check claims komeda resources
   (scaler and wb_layer) accroding to its state configuration to the
   wb_connector. and the wb_state configuration will be validated on the
   specific component resources to see if the caps of component can
   meet the requirement of wb_connector. if not check failed.
4. Update irq_handler to notify the completion of writeback.

NOTE:
This change doesn't add scaling writeback support, that support will
be added in the future after the scaler support.

v2: Rebase
v3: Rebase and constify the d71_wb_layer_funcs
v4: Addressed Ayan's comments

Depends on:
- https://patchwork.freedesktop.org/series/59915/Signed-off-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Acked-by: Ayan Kumar Halder <ayan.halder@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>

Maarten needs -rc4 backmerged so he can pull in the fbcon notifier
removal topic branch into drm-misc-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Pull x86 fixes from Thomas Gleixner:
 "The accumulated fixes from this and last week:

   - Fix vmalloc TLB flush and map range calculations which lead to
     stale TLBs, spurious faults and other hard to diagnose issues.

   - Use fault_in_pages_writable() for prefaulting the user stack in the
     FPU code as it's less fragile than the current solution

   - Use the PF_KTHREAD flag when checking for a kernel thread instead
     of current->mm as the latter can give the wrong answer due to
     use_mm()

   - Compute the vmemmap size correctly for KASLR and 5-Level paging.
     Otherwise this can end up with a way too small vmemmap area.

   - Make KASAN and 5-level paging work again by making sure that all
     invalid bits are masked out when computing the P4D offset. This
     worked before but got broken recently when the LDT remap area was
     moved.

   - Prevent a NULL pointer dereference in the resource control code
     which can be triggered with certain mount options when the
     requested resource is not available.

   - Enforce ordering of microcode loading vs. perf initialization on
     secondary CPUs. Otherwise perf tries to access a non-existing MSR
     as the boot CPU marked it as available.

   - Don't stop the resource control group walk early otherwise the
     control bitmaps are not updated correctly and become inconsistent.

   - Unbreak kgdb by returning 0 on success from
     kgdb_arch_set_breakpoint() instead of an error code.

   - Add more Icelake CPU model defines so depending changes can be
     queued in other trees"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/microcode, cpuhotplug: Add a microcode loader CPU hotplug callback
  x86/kasan: Fix boot with 5-level paging and KASAN
  x86/fpu: Don't use current->mm to check for a kthread
  x86/kgdb: Return 0 from kgdb_arch_set_breakpoint()
  x86/resctrl: Prevent NULL pointer dereference when local MBM is disabled
  x86/resctrl: Don't stop walking closids when a locksetup group is found
  x86/fpu: Update kernel's FPU state before using for the fsave header
  x86/mm/KASLR: Compute the size of the vmemmap section properly
  x86/fpu: Use fault_in_pages_writeable() for pre-faulting
  x86/CPU: Add more Icelake model numbers
  mm/vmalloc: Avoid rare case of flushing TLB with weird arguments
  mm/vmalloc: Fix calculation of direct map addr range

Pull timer fixes from Thomas Gleixner:
 "A set of small fixes:

   - Repair the ktime_get_coarse() functions so they actually deliver
     what they are supposed to: tick granular time stamps. The current
     code missed to add the accumulated nanoseconds part of the
     timekeeper so the resulting granularity was 1 second.

   - Prevent the tracer from infinitely recursing into time getter
     functions in the arm architectured timer by marking these functions
     notrace

   - Fix a trivial compiler warning caused by wrong qualifier ordering"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Repair ktime_get_coarse*() granularity
  clocksource/drivers/arm_arch_timer: Don't trace count reader functions
  clocksource/drivers/timer-ti-dm: Change to new style declaration

Pull RAS fixes from Thomas Gleixner:
 "Two small fixes for RAS:

   - Use a proper search algorithm to find the correct element in the
     CEC array. The replacement was a better choice than fixing the
     crash causes by the original search function with horrible duct
     tape.

   - Move the timer based decay function into thread context so it can
     actually acquire the mutex which protects the CEC array to prevent
     corruption"

* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  RAS/CEC: Convert the timer callback to a workqueue
  RAS/CEC: Fix binary search function

Pull x86 platform driver fixes from Andy Shevchenko:

 - fix a couple of Mellanox driver enumeration issues

 - fix ASUS laptop regression with backlight

 - fix Dell computers that got a wrong mode (tablet versus laptop) after
   resume

* tag 'platform-drivers-x86-v5.2-3' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/mellanox: mlxreg-hotplug: Add devm_free_irq call to remove flow
  platform/x86: mlx-platform: Fix parent device in i2c-mux-reg device registration
  platform/x86: intel-vbtn: Report switch events when event wakes device
  platform/x86: asus-wmi: Only Tell EC the OS will handle display hotkeys from asus_nb_wmi

Pull USB fixes from Greg KH:
 "Here are some small USB driver fixes for 5.2-rc5

  Nothing major, just some small gadget fixes, usb-serial new device
  ids, a few new quirks, and some small fixes for some regressions that
  have been found after the big 5.2-rc1 merge.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: Make sure an alt mode exist before getting its partner
  usb: gadget: udc: lpc32xx: fix return value check in lpc32xx_udc_probe()
  usb: gadget: dwc2: fix zlp handling
  usb: dwc2: Set actual frame number for completed ISOC transfer for none DDMA
  usb: gadget: udc: lpc32xx: allocate descriptor with GFP_ATOMIC
  usb: gadget: fusb300_udc: Fix memory leak of fusb300->ep[i]
  usb: phy: mxs: Disable external charger detect in mxs_phy_hw_init()
  usb: dwc2: Fix DMA cache alignment issues
  usb: dwc2: host: Fix wMaxPacketSize handling (fix webcam regression)
  USB: Fix chipmunk-like voice when using Logitech C270 for recording audio.
  USB: usb-storage: Add new ID to ums-realtek
  usb: typec: ucsi: ccg: fix memory leak in do_flash
  USB: serial: option: add Telit 0x1260 and 0x1261 compositions
  USB: serial: pl2303: add Allied Telesis VT-Kit3
  USB: serial: option: add support for Simcom SIM7500/SIM7600 RNDIS mode

Pull powerpc fixes from Michael Ellerman:
 "One fix for a regression introduced by our 32-bit KASAN support, which
  broke booting on machines with "bootx" early debugging enabled.

  A fix for a bug which broke kexec on 32-bit, introduced by changes to
  the 32-bit STRICT_KERNEL_RWX support in v5.1.

  Finally two fixes going to stable for our THP split/collapse handling,
  discovered by Nick. The first fixes random crashes and/or corruption
  in guests under sufficient load.

  Thanks to: Nicholas Piggin, Christophe Leroy, Aaro Koskinen, Mathieu
  Malaterre"

* tag 'powerpc-5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/32s: fix booting with CONFIG_PPC_EARLY_DEBUG_BOOTX
  powerpc/64s: __find_linux_pte() synchronization vs pmdp_invalidate()
  powerpc/64s: Fix THP PMD collapse serialisation
  powerpc: Fix kexec failure on book3s/32

Pull tracing fixes from Steven Rostedt:

 - Out of range read of stack trace output

 - Fix for NULL pointer dereference in trace_uprobe_create()

 - Fix to a livepatching / ftrace permission race in the module code

 - Fix for NULL pointer dereference in free_ftrace_func_mapper()

 - A couple of build warning clean ups

* tag 'trace-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Fix NULL pointer dereference in free_ftrace_func_mapper()
  module: Fix livepatch/ftrace module text permissions race
  tracing/uprobe: Fix obsolete comment on trace_uprobe_create()
  tracing/uprobe: Fix NULL pointer dereference in trace_uprobe_create()
  tracing: Make two symbols static
  tracing: avoid build warning with HAVE_NOP_MCOUNT
  tracing: Fix out-of-range read in trace_stack_print()

Adric Blake reported the following warning during suspend-resume:

  Enabling non-boot CPUs ...
  x86: Booting SMP configuration:
  smpboot: Booting Node 0 Processor 1 APIC 0x2
  unchecked MSR access error: WRMSR to 0x10f (tried to write 0x0000000000000000) \
   at rIP: 0xffffffff8d267924 (native_write_msr+0x4/0x20)
  Call Trace:
   intel_set_tfa
   intel_pmu_cpu_starting
   ? x86_pmu_dead_cpu
   x86_pmu_starting_cpu
   cpuhp_invoke_callback
   ? _raw_spin_lock_irqsave
   notify_cpu_starting
   start_secondary
   secondary_startup_64
  microcode: sig=0x806ea, pf=0x80, revision=0x96
  microcode: updated to revision 0xb4, date = 2019-04-01
  CPU1 is up

The MSR in question is MSR_TFA_RTM_FORCE_ABORT and that MSR is emulated
by microcode. The log above shows that the microcode loader callback
happens after the PMU restoration, leading to the conjecture that
because the microcode hasn't been updated yet, that MSR is not present
yet, leading to the #GP.

Add a microcode loader-specific hotplug vector which comes before
the PERF vectors and thus executes earlier and makes sure the MSR is
present.

Fixes: 400816f6 ("perf/x86/intel: Implement support for TSX Force Abort")
Reported-by: Adric Blake <promarbler14@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: x86@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203637

Pull cgroup fixes from Tejun Heo:
 "This has an unusually high density of tricky fixes:

   - task_get_css() could deadlock when it races against a dying cgroup.

   - cgroup.procs didn't list thread group leaders with live threads.

     This could mislead readers to think that a cgroup is empty when
     it's not. Fixed by making PROCS iterator include dead tasks. I made
     a couple mistakes making this change and this pull request contains
     a couple follow-up patches.

   - When cpusets run out of online cpus, it updates cpusmasks of member
     tasks in bizarre ways. Joel improved the behavior significantly"

* 'for-5.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cpuset: restore sanity to cpuset_cpus_allowed_fallback()
  cgroup: Fix css_task_iter_advance_css_set() cset skip condition
  cgroup: css_task_iter_skip()'d iterators must be advanced before accessed
  cgroup: Include dying leaders with live threads in PROCS iterations
  cgroup: Implement css_task_iter_skip()
  cgroup: Call cgroup_release() before __exit_signal()
  docs cgroups: add another example size for hugetlb
  cgroup: Use css_tryget() instead of css_tryget_online() in task_get_css()

Pull drm fixes from Daniel Vetter:
 "Nothing unsettling here, also not aware of anything serious still
  pending.

  The edid override regression fix took a bit longer since this seems to
  be an area with an overabundance of bad options. But the fix we have
  now seems like a good path forward.

  Next week it should be back to Dave.

  Summary:

   - fix regression on amdgpu on SI

   - fix edid override regression

   - driver fixes: amdgpu, i915, mediatek, meson, panfrost

   - fix writecombine for vmap in gem-shmem helper (used by panfrost)

   - add more panel quirks"

* tag 'drm-fixes-2019-06-14' of git://anongit.freedesktop.org/drm/drm: (25 commits)
  drm/amdgpu: return 0 by default in amdgpu_pm_load_smu_firmware
  drm/amdgpu: Fix bounds checking in amdgpu_ras_is_supported()
  drm: add fallback override/firmware EDID modes workaround
  drm/edid: abstract override/firmware EDID retrieval
  drm/i915/perf: fix whitelist on Gen10+
  drm/i915/sdvo: Implement proper HDMI audio support for SDVO
  drm/i915: Fix per-pixel alpha with CCS
  drm/i915/dmc: protect against reading random memory
  drm/i915/dsi: Use a fuzzy check for burst mode clock check
  drm/amdgpu/{uvd,vcn}: fetch ring's read_ptr after alloc
  drm/panfrost: Require the simple_ondemand governor
  drm/panfrost: make devfreq optional again
  drm/gem_shmem: Use a writecombine mapping for ->vaddr
  drm: panel-orientation-quirks: Add quirk for GPD MicroPC
  drm: panel-orientation-quirks: Add quirk for GPD pocket2
  drm/meson: fix G12A primary plane disabling
  drm/meson: fix primary plane disabling
  drm/meson: fix G12A HDMI PLL settings for 4K60 1000/1001 variations
  drm/mediatek: call mtk_dsi_stop() after mtk_drm_crtc_atomic_disable()
  drm/mediatek: clear num_pipes when unbind driver
  ...

Pull gfs2 fix from Andreas Gruenbacher:
 "Fix rounding error in gfs2_iomap_page_prepare"

* tag 'gfs2-v5.2.fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
  gfs2: Fix rounding error in gfs2_iomap_page_prepare