This board has an EEPROM (STMicroelectronics M24C64-WMN6TP) connected
to the I2C channel 0 of the SoC.  Its slave address is 0x54.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Add master clock nodes generated by crystal oscillators.

  PH1-sLD3, PH1-LD4: 24.576 MHz
  PH1-Pro4, ProXstream2: 25.000 MHz
  PH1-Pro5: 20.000 MHz
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

During the review process of the UniPhier System Bus driver
(drivers/bus/uniphier.c), the current binding of the System Bus
Controller turned out to be no good.  In order to make the driver
really usable, we have to switch over to the new binding defined by
Documentation/devicetree/bindings/bus/uniphier-system-bus.txt.
The old binding will be still supported for a while to keep the
backward compatibility.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This property is used in common by several boards.  Move it to the
common place (uniphier-support-card.dtsi).  If necessary, each board
can still override the property.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Due to the company's awful projecting, this chip has been renamed to
PH1-LD20.  It has not been shipped yet, this change would have no
impact on our customers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'imx-dt-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt2

Merge "i.MX device tree updates for 4.6" from Shawn Guo:

- New i.MX6 board support: NXP/Freescale imx6qp boards, Advantech/GE,
  Uniwest evi, Engicam IMX6 Q7, Toradex Apalis SoM and Ixora carrier
  boards
- Relicense vf610 dts files under GPLv2/X11
- A patch series from Stefan updating Vybrid Colibri board support with
  PMU, regulators and other devices enabled
- Correct PWM pinmux for Ventana boards and add more pinmux for GW54xx
- Clean up imx6q-tbs2910 dts file and add SATA PHY configuration
- A series from Russell cleaning up hummingboard dts files
- A series from Lothar updating Ka-Ro i.MX28, i.MX53 and i.MX6 boards
  to use better audio codec frequency and display configurations
- Clean up whitespaces in i.MX6UL pinctrl header and add more devices
  support for the SoC
- Other random dts updates to enable various devices

* tag 'imx-dt-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (75 commits)
  ARM: dts: imx53-qsb: Fix gpio button polarity
  ARM: dts: vfxxx: Add DAC node for Vybrid SoC
  ARM: dts: imx6q: add missing links between ipu2 and mipi dsi
  ARM: dts: imx: Add support for Advantech/GE B850v3
  ARM: dts: imx: Add support for Advantech/GE B650v3
  ARM: dts: imx: Add support for Advantech/GE B450v3
  ARM: dts: imx: Add support for Advantech/GE Bx50v3
  ARM: dts: imx: Add Advantech BA-16 Qseven module
  of: Add vendor prefix for General Electric Company
  of: Add vendor prefix for Advantech Corporation
  ARM: dts: imx35.dtsi: change the clock information for usb
  ARM: dts: imx25.dtsi: change the clock information for usb
  ARM: dts: imx6ul: add kpp support
  ARM: dts: imx6ul: add gpmi support
  ARM: dts: imx6ul: add lcdif support
  ARM: dts: imx6ul: add sai support
  ARM: dts: imx6ul: add flexcan support
  ARM: dts: imx6ul: add sdma support
  ARM: dts: imx6ul: add pwm[1-4] nodes
  ARM: dts: imx6ul: disable PWMs by default
  ...

The polarity of the gpio buttons is defined to '0' which is
active high. The buttons are active low though which has been verified by
testing it and by looking into the schematics. While at it use
defines rathers than numbers for the key codes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a device tree node entry for DAC peripheral on Vybrid SoC.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The backlinks are already there since commit 4520e692 ("ARM: dts:
imx6qdl: Add IPU DI ports and endpoints, move imx-drm node to dtsi")
and were moved by commit 70c2652c ("ARM: dts: imx6qdl: Move existing
MIPI DSI ports into a new 'ports' node"), but the links from IPU2 DI0/1
to the MIPI DSI mux are missing. Fix this.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Advantech/GE B850v3 board.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Advantech/GE B650v3 board.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Advantech/GE B450v3 board.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Advantech has 3 carrier boards (B450v3, B650v3, B850v3) which use
the Advantech BA-16 module (based on iMX6D). This file has the
devicetree entries that are common to all 3 boards.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Advantech BA-16 module based on iMX6D processor

Basic information about the module:
 - Module manufacturer: Advantech
 - CPU: Freescale ARM Cortex-A9 i.MX6
 - SPECS:
     Up to 2GB Onboard DDR3 Memory;
     Up to 16GB Onboard eMMC NAND Flash
     Supports OpenGL ES 2.0 and OpenVG 1.1
     HDMI, 24-bit LVDS
     1x UART, 2x I2C, 8x GPIO,
     4x Host USB 2.0 port, 1x USB OTG port,
     1x micro SD (SDHC),1x SDIO, 1x SATA II,
     1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2
 - Website: http://goo.gl/JED98USigned-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds vendor prefix for General Electric Company
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds vendor prefix for Advantech Corporation.
Website: http://www.advantech.com/Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

For imx35, it needs three clocks to let the controller work,
the old code is wrong, and the usbmisc does not include
clock handling code any more.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

For imx25, it needs three clocks to let the controller work,
the old code is wrong, and usbmisc has not included clock
handling code any more.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds the device node for the i.MX6UL keypad controller.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the device node for the i.MX6UL GPMI interface and the related
APBH DMA which is necessary for the GPMI to work properly.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the device node for the i.MX6UL eLCDIF interface.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device nodes for the i.MX6UL synchronous audio interfaces (SAI).
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device nodes for the i.MX6UL flexcan interfaces.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device node for the i.MX6UL SDMA unit.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device nodes for the PWM uinits 1..4 which were missing in the
original commit for i.MX6UL support.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since PWMs are only useful if they are actually connected to an output pin,
let users enable them explicitly in their device trees where they should
also set up the pin configuration. This is in sync with a recent change
(commit e2675266 "ARM: dts: imx6qdl: disable PWMs by default")
to other i.MX SoCs.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX6UL PWMs require real clocks. Define the appropriate clocks for
the PWM units.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX6UL GPT unit requires real clocks. Define the appropriate
clocks to make it work.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6ul.dtsi references the macro 'KEY_POWER' from
dt-bindings/input/input.h. Thus, move the include statement for this
file from imx6ul-14x14-evk.dts to imx6ul.dtsi itself.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Move the tsc node to keep the nodes sorted in ascending order by unit
address.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pad DISPB2_SER_RS has no function DISP1_EXT_CLK.
The definition is obviusly a copy/paste error from
MX51_PAD_DISPB2_SER_RS__DISP1_PIN16.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Various pads are missing the input_sel offset and value. Fix this.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove whitespace before TAB in indentation and reduce indentation
level to improve readability.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add pinmux for UART_A RTS, CTS pin's.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

All Freescale Vybrid SoC include a Cortex-A5 core which supports
ARM's standard PMU (performance monitoring unit). Include the
monitoring unit into the Cortex-A5 base device tree vf500.dtsi.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Colibri standard does not define a pin for SD-Card write-
protection. Use the disable-wp property to indicate that there
is no physical WP line present.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to the reference manual the shp_2_mcu / mcu_2_shp
scripts must be used for devices connected through the SPBA.

This fixes an issue we saw with DMA transfers from SPI NOR Flashes.
Sometimes the SPI controller RX FIFO was not empty after a DMA
transfer and the driver got stuck in the next PIO transfer when
it read one word more than expected.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the carrier boards 3.3V supply as fixed regulator. This allows
to specify the power supply for nodes like backlight.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Colibri modules need to be powered using the power pins 3V3 and
AVDD_AUDIO. Add fixed regulators which represent this power rails.
Potentially, those power rails could be switched on a carrier
board. A carrier board device tree could add a own regulator with
a GPIO, and reference that regulator in a vin-supply property of
those new module level system regulators.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Drop the fake simple-bus container 'regulators' and put the
regulators directly under the root node. This also makes the
artificial 'reg' properties superfluous. While at it, remove
the unnecessary regulator-always-on property and name the
regulators according to schematics.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>