The policydb permission set has left the xbits unused. Make them
available for mediation.

Note: that this does not bring full auditing control of the
permissions as there are not enough bits. The quieting of denials is
provided as that is used more than forced auditing of allowed
permissions.
Signed-off-by: John Johansen <john.johansen@canonical.com>

the v8 and earlier policy does not encode the locking permission for
no-fs unix sockets. However the kernel is enforcing mediation.

Add the AA_MAY_LOCK perm to v8 and earlier computed perm mask which will
grant permission for all current abi profiles, but still allow specifying
auditing of the operation if needed.

Link: http://bugs.launchpad.net/bugs/1780227Signed-off-by: John Johansen <john.johansen@canonical.com>

The v8 abi is supported by the kernel but the userspace supported
version check does not allow for it. This was missed when v8 was added
due to a bug in the userspace compiler which was setting an older abi
version for v8 encoding (which is forward compatible except on the
network encoding). However it is possible to detect the network
encoding by checking the policydb network support which the code
does. The end result was that missing the abi flag worked until
userspace was fixed and began correctly checking for the v8 abi
version.

Fixes: 56974a6f ("apparmor: add base infastructure for socket mediation")
Signed-off-by: John Johansen <john.johansen@canonical.com>

Convert from an unsigned int to a state_t for state position. This is
a step in prepping for the state position carrying some additional
flags, and a limited form of backtracking to support variables.
Signed-off-by: John Johansen <john.johansen@canonical.com>

Remap polidydb dfa accept table from embedded perms to an index, and
then move the perm lookup to use the accept entry as an index into the
perm table. This is done so that the perm table can be separated from
the dfa, allowing dfa accept to index to share expanded permission
sets.
Signed-off-by: John Johansen <john.johansen@canonical.com>

The shared permissions struct has the stop field which is unneeded
and the "reserved" subtree field commented which is needed. Also
reorganize so that the entries are logically grouped.
Signed-off-by: John Johansen <john.johansen@canonical.com>

Remap xmatch dfa accept table from embedded perms to an index and then
move xmatch lookup to use accept entry to index into the xmatch table.

This is step towards unifying permission lookup and reducing the
size of permissions tables.
Signed-off-by: John Johansen <john.johansen@canonical.com>

Remap file dfa accept table from embedded perms to index and then move
fperm lookup to use the accept entry as an index into the fperm table.

This is a step toward unifying permission lookup.
Signed-off-by: John Johansen <john.johansen@canonical.com>

continue permission unification by converting xmatch to use the
policydb struct that is used by the other profile dfas.
Signed-off-by: John Johansen <john.johansen@canonical.com>

file_rules and policydb are almost the same and will need the same
features in the future so combine them.
Signed-off-by: John Johansen <john.johansen@canonical.com>

Rather than computing policydb permissions for each access
permissions can be computed once on profile load and stored for lookup.
Signed-off-by: John Johansen <john.johansen@canonical.com>

Convert xmatch from using perms encoded in the accept entry of the
dfa to the common external aa_perms in a table.
Signed-off-by: John Johansen <john.johansen@canonical.com>

shorten the name of some of the mapping functions which shortens line
lengths.

change the mapping so it returns the perm table instead of operating
directly on the file struct.

Handle potential memory allocation failure.
Signed-off-by: John Johansen <john.johansen@canonical.com>

fperm computation is only needed during policy_unpack so move the
code there to isolate it fromt the run time code.
Signed-off-by: John Johansen <john.johansen@canonical.com>

Rather than computing xmatch permissions each time access is requested,
these permissions can be computed once on profile load and stored for
lookup.
Signed-off-by: Mike Salvatore <mike.salvatore@canonical.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>

Rather than computing file permissions for each file access, file
permissions can be computed once on profile load and stored for lookup.
Signed-off-by: Mike Salvatore <mike.salvatore@canonical.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>

Create two new files in apparmor's sysfs:

/sys/kernel/security/apparmor/raw_data_compression_level_min
/sys/kernel/security/apparmor/raw_data_compression_level_max

These correspond to the minimum and maximum zstd compression levels
that can be assigned to the apparmor module parameter
raw_data_compression_level.
Signed-off-by: Jon Tourville <jon.tourville@canonical.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>

Change the algorithm used by apparmor to compress profile data from
zlib to zstd, using the new zstd API introduced in 5.16.

Zstd provides a larger range of compression levels than zlib and
significantly better performance at the default level (for a relatively
small increase in compressed size).

The apparmor module parameter raw_data_compression_level is now clamped
to the minimum and maximum compression levels reported by the zstd
library. A compression level of 0 retains the previous behavior of
disabling policy compression instead of using zstd's behavior, which is
to use the default compression level.
Signed-off-by: Jon Tourville <jon.tourville@canonical.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>

Reserve mediation classes that exist in out of tree development
branches or are used by userspace mediation helpers.
Signed-off-by: John Johansen <john.johansen@canonical.com>

Fix the following lockdep warning

[ 1119.158984] ============================================
[ 1119.158988] WARNING: possible recursive locking detected
[ 1119.158996] 6.0.0-rc1+ #257 Tainted: G            E    N
[ 1119.158999] --------------------------------------------
[ 1119.159001] bash/80100 is trying to acquire lock:
[ 1119.159007] ffff88803e79b4a0 (&ns->lock/1){+.+.}-{4:4}, at: destroy_ns.part.0+0x43/0x140
[ 1119.159028]
               but task is already holding lock:
[ 1119.159030] ffff8881009764a0 (&ns->lock/1){+.+.}-{4:4}, at: aa_remove_profiles+0x3f0/0x640
[ 1119.159040]
               other info that might help us debug this:
[ 1119.159042]  Possible unsafe locking scenario:

[ 1119.159043]        CPU0
[ 1119.159045]        ----
[ 1119.159047]   lock(&ns->lock/1);
[ 1119.159051]   lock(&ns->lock/1);
[ 1119.159055]
                *** DEADLOCK ***

Which is caused by an incorrect lockdep nesting notation

Fixes: feb3c766 ("apparmor: fix possible recursive lock warning in __aa_create_ns")
Signed-off-by: John Johansen <john.johansen@canonical.com>

In multi_transaction_new(), the variable t is not freed or passed out
on the failure of copy_from_user(t->data, buf, size), which could lead
to a memleak.

Fix this bug by adding a put_multi_transaction(t) in the error path.

Fixes: 1dea3b41 ("apparmor: speed up transactional queries")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>

Pull NIOS2 fixes from Dinh Nguyen:

 - Security fixes from Al Viro

* tag 'nios2_fixes_v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  nios2: add force_successful_syscall_return()
  nios2: restarts apply only to the first sigframe we build...
  nios2: fix syscall restart checks
  nios2: traced syscall does need to check the syscall number
  nios2: don't leave NULLs in sys_call_table[]
  nios2: page fault et.al. are *not* restartable syscalls...

Pull spi fixes from Mark Brown:
 "A few fixes that came in since my pull request, the Meson fix is a
  little large since it's fixing all possible cases of the problem that
  was observed with the driver and clock API trying to share
  configuration by integrating the device clocking fully with the clock
  API rather than spot fixing the one instance that was observed"

* tag 'spi-fix-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: dt-bindings: Drop Pratyush Yadav
  spi: meson-spicc: add local pow2 clock ops to preserve rate between messages
  MAINTAINERS: rectify entry for ARM/HPE GXP ARCHITECTURE
  spi: spi.c: Add missing __percpu annotations in users of spi_statistics

Merge tag 'regulator-fix-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator fixes from Mark Brown:
 "A couple of small fixes that came in since my pull request, nothing
  major here"

* tag 'regulator-fix-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: core: Fix missing error return from regulator_bulk_get()
  regulator: pca9450: Remove restrictions for regulator-name

The exception for the "unaligned access at the end of the page, next
page not mapped" never happens, but the fixup code ends up causing
trouble for compilers to optimize well.

clang in particular ends up seeing it being in the middle of a loop, and
tries desperately to optimize the exception fixup code that is never
really reached.

The simple solution is to just move all the fixups into the exception
handler itself, which moves it all out of the hot case code, and means
that the compiler never sees it or needs to worry about it.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

These operations are documented as always ordered in
include/asm-generic/bitops/instrumented-atomic.h, and producer-consumer
type use cases where one side needs to ensure a flag is left pending
after some shared data was updated rely on this ordering, even in the
failure case.

This is the case with the workqueue code, which currently suffers from a
reproducible ordering violation on Apple M1 platforms (which are
notoriously out-of-order) that ends up causing the TTY layer to fail to
deliver data to userspace properly under the right conditions.  This
change fixes that bug.

Change the documentation to restrict the "no order on failure" story to
the _lock() variant (for which it makes sense), and remove the
early-exit from the generic implementation, which is what causes the
missing barrier semantics in that case.  Without this, the remaining
atomic op is fully ordered (including on ARM64 LSE, as of recent
versions of the architecture spec).
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Fixes: e986a0d6 ("locking/atomics, asm-generic/bitops/atomic.h: Rewrite using atomic_*() APIs")
Fixes: 61e02392 ("locking/atomic/bitops: Document and clarify ordering semantics for failed test_and_{}_bit()")
Signed-off-by: Hector Martin <marcan@marcan.st>
Acked-by: Will Deacon <will@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If we use the ancient SysV syscall ABI, we'd better have tell the
kernel how to claim that a negative return value is a success.
Use ->orig_r2 for that - it's inaccessible via ptrace, so it's
a fair game for changes and it's normally[*] non-negative on return
from syscall.  Set to -1; syscall is not going to be restart-worthy
by definition, so we won't interfere with that use either.

[*] the only exception is rt_sigreturn(), where we skip the entire
messing with r1/r2 anyway.

Fixes: 82ed08dd ("nios2: Exception handling")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

Fixes: b53e906d ("nios2: Signal handling support")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

sys_foo() returns -512 (aka -ERESTARTSYS) => do_signal() sees
512 in r2 and 1 in r1.

sys_foo() returns 512 => do_signal() sees 512 in r2 and 0 in r1.

The former is restart-worthy; the latter obviously isn't.

Fixes: b53e906d ("nios2: Signal handling support")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

all checks done before letting the tracer modify the register
state are worthless...

Fixes: 82ed08dd ("nios2: Exception handling")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

fill the gaps in there with sys_ni_syscall, as everyone does...

Fixes: 82ed08dd ("nios2: Exception handling")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

make sure that ->orig_r2 is negative for everything except
the syscalls.

Fixes: 82ed08dd ("nios2: Exception handling")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>

Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we
have gfp_types.h for this.

Fixes powerpc allmodconfig build:

   In file included from include/linux/nodemask.h:97,
                    from include/linux/mmzone.h:17,
                    from include/linux/gfp.h:7,
                    from include/linux/radix-tree.h:12,
                    from include/linux/idr.h:15,
                    from include/linux/kernfs.h:12,
                    from include/linux/sysfs.h:16,
                    from include/linux/kobject.h:20,
                    from include/linux/pci.h:35,
                    from arch/powerpc/kernel/prom_init.c:24:
   include/linux/random.h: In function 'add_latent_entropy':
>> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'?
      25 |         add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
         |                                              ^~~~~~~~~~~~~~
         |                                              add_latent_entropy
   include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: kernel test robot <lkp@intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull vfs lseek fix from Al Viro:
 "Fix proc_reg_llseek() breakage. Always had been possible if somebody
  left NULL ->proc_lseek, became a practical issue now"

* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  take care to handle NULL ->proc_lseek()

Easily done now, just by clearing FMODE_LSEEK in ->f_mode
during proc_reg_open() for such entries.

Fixes: 868941b1 "fs: remove no_llseek"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull more xen updates from Juergen Gross:

 - fix the handling of the "persistent grants" feature negotiation
   between Xen blkfront and Xen blkback drivers

 - a cleanup of xen.config and adding xen.config to Xen section in
   MAINTAINERS

 - support HVMOP_set_evtchn_upcall_vector, which is more compliant to
   "normal" interrupt handling than the global callback used up to now

 - further small cleanups

* tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections
  xen: remove XEN_SCRUB_PAGES in xen.config
  xen/pciback: Fix comment typo
  xen/xenbus: fix return type in xenbus_file_read()
  xen-blkfront: Apply 'feature_persistent' parameter when connect
  xen-blkback: Apply 'feature_persistent' parameter when connect
  xen-blkback: fix persistent grants negotiation
  x86/xen: Add support for HVMOP_set_evtchn_upcall_vector

Merge tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull more perf tool updates from Arnaldo Carvalho de Melo:

 - 'perf c2c' now supports ARM64, adjust its output to cope with
   differences with what is in x86_64. Now go find false sharing on
   ARM64 (at least Neoverse) as well!

 - Refactor the JSON processing, making the output more compact and thus
   reducing the size of the resulting perf binary

 - Improvements for 'perf offcpu' profiling, including tracking child
   processes

 - Update Intel JSON metrics and events files for broadwellde,
   broadwellx, cascadelakex, haswellx, icelakex, ivytown, jaketown,
   knightslanding, sapphirerapids, skylakex and snowridgex

 - Add 'perf stat' JSON output and a 'perf test' entry for it

 - Ignore memfd and anonymous mmap events if jitdump present

 - Refactor 'perf test' shell tests allowing subdirs

 - Fix an error handling path in 'parse_perf_probe_command()'

 - Fixes for the guest Intel PT tracing patchkit in the 1st batch of
   this merge window

 - Print debuginfod queries if -v option is used, to explain delays in
   processing when debuginfo servers are enabled to fetch DSOs with
   richer symbol tables

 - Improve error message for 'perf record -p not_existing_pid'

 - Fix openssl and libbpf feature detection

 - Add PMU pai_crypto event description for IBM z16 on 'perf list'

 - Fix typos and duplicated words on comments in various places

* tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (81 commits)
  perf test: Refactor shell tests allowing subdirs
  perf vendor events: Update events for snowridgex
  perf vendor events: Update events and metrics for skylakex
  perf vendor events: Update metrics for sapphirerapids
  perf vendor events: Update events for knightslanding
  perf vendor events: Update metrics for jaketown
  perf vendor events: Update metrics for ivytown
  perf vendor events: Update events and metrics for icelakex
  perf vendor events: Update events and metrics for haswellx
  perf vendor events: Update events and metrics for cascadelakex
  perf vendor events: Update events and metrics for broadwellx
  perf vendor events: Update metrics for broadwellde
  perf jevents: Fold strings optimization
  perf jevents: Compress the pmu_events_table
  perf metrics: Copy entire pmu_event in find metric
  perf pmu-events: Hide the pmu_events
  perf pmu-events: Don't assume pmu_event is an array
  perf pmu-events: Move test events/metrics to JSON
  perf test: Use full metric resolution
  perf pmu-events: Hide pmu_events_map
  ...

Pull powerpc fixes from Michael Ellerman:

 - Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit
   CPUs trap on it rather than ignoring it as they should.

 - Fix ftrace when building with clang, which was broken by some
   refactoring.

 - A couple of other minor fixes.

Thanks to Christophe Leroy, Naveen N.  Rao, Nick Desaulniers, Ondrej
Mosnacek, Pali Rohár, Russell Currey, and Segher Boessenkool.

* tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/kexec: Fix build failure from uninitialised variable
  powerpc/ppc-opcode: Fix PPC_RAW_TW()
  powerpc64/ftrace: Fix ftrace for clang builds
  powerpc: Make eh value more explicit when using lwarx
  powerpc: Don't hide eh field of lwarx behind a macro
  powerpc: Fix eh field when calling lwarx on PPC32

Pull /proc/mounts fix from Al Viro:
 "Fix for /proc/mounts escaping - escape the '#' character too"

* tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  vfs: escape hash as well