During initialization, if we encounter errors, there is a code path that
calls bnxt_hwrm_vnic_set_tpa() with invalid VNIC ID.  This may cause a
warning in firmware logs.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_restore_pf_fw_resources routine frees PF resources by calling
close_nic and allocates the resources back, by doing open_nic. However,
this is not needed, if the PF is already in closed state.

This bug causes the driver to call open the device and call request_irq()
when it is not needed.  Ultimately, pci_disable_msix() will crash
when bnxt_en is unloaded.

This patch fixes the problem by skipping __bnxt_close_nic and
__bnxt_open_nic inside bnxt_restore_pf_fw_resources routine, if the
interface is not running.

Fixes: 80fcaf46 ("bnxt_en: Restore MSIX after disabling SRIOV.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, internal error value is returned by the driver, when
hwrm_cfa_flow_alloc() fails due lack of resources.  We should be returning
Linux errno value -ENOSPC instead.

This patch also converts other similar command errors to standard Linux errno
code (-EIO) in bnxt_tc.c

Fixes: db1d36a2 ("bnxt_en: add TC flower offload flow_alloc/free FW cmds")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent changes added the bnxt_init_int_mode() call in the driver's open
path whenever ring reservations are changed.  This call was previously
only called in the probe path.  In the open path, if MQPRIO TC has been
setup, the bnxt_init_int_mode() call would reset and mess up the MQPRIO
per TC rings.

Fix it by not re-initilizing bp->tx_nr_rings_per_tc in
bnxt_init_int_mode().  Instead, initialize it in the probe path only
after the bnxt_init_int_mode() call.

Fixes: 674f50a5 ("bnxt_en: Implement new method to reserve rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When receiving a packet with VLAN tag, pass the entire 16-bit TCI to the
stack when calling __vlan_hwaccel_put_tag().  The current code is only
passing the 12-bit tag and it is missing the priority bits.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some conditions when the driver fails to add a flow in HW and returns
an error back to the stack, the stack continues to invoke get_flow_stats()
and/or del_flow() on it. The driver fails these APIs with an error message
"no flow_node for cookie". The message gets logged repeatedly as long as
the stack keeps invoking these functions.

Fix this by removing the corresponding netdev_info() calls from these
functions.

Fixes: d7bc7305 ("bnxt_en: add code to query TC flower offload stats")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The number of vnics to check must be determined ahead of time because
only standard RX rings require vnics to support RFS.  The logic is
similar to the ring reservation logic and we can now use the
refactored common functions to do most of the work in setting up
the firmware message.

Fixes: 8f23d638 ("bnxt_en: Expand bnxt_check_rings() to check all resources.")
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bnxt_hwrm_reserve_{pf|vf}_rings() functions are very similar to
the bnxt_hwrm_check_{pf|vf}_rings() functions.  Refactor the former
so that the latter can make use of common code in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In 664fcf12 (net: phy: Threaded interrupts allow some simplification)
the phy_interrupt system was changed to use a traditional threaded
interrupt scheme instead of a workqueue approach.

With this change, the phy status check moved into phy_change, which
did not report back to the caller whether or not the interrupt was
handled. This means that, in the case of a shared phy interrupt,
only the first phydev's interrupt registers are checked (since
phy_interrupt() would always return IRQ_HANDLED). This leads to
interrupt storms when it is a secondary device that's actually the
interrupt source.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Max delat_t should be the full_bucket/rate instead of the full_bucket.
Also report EINVAL if the rate is zero.

Fixes: 96fbc13d ("openvswitch: Add meter infrastructure")
Cc: Andy Zhou <azhou@ovn.org>
Signed-off-by: zhangliping <zhangliping02@baidu.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding a macvlan device on top of a lowerdev that supports
the xfrm offloads fails with a new regression:
  # ip link add link ens1f0 mv0 type macvlan
  RTNETLINK answers: Operation not permitted

Tracing down the failure shows that the macvlan device inherits
the NETIF_F_HW_ESP and NETIF_F_HW_ESP_TX_CSUM feature flags
from the lowerdev, but with no dev->xfrmdev_ops API filled
in, it doesn't actually support xfrm.  When the request is
made to add the new macvlan device, the XFRM listener for
NETDEV_REGISTER calls xfrm_api_check() which fails the new
registration because dev->xfrmdev_ops is NULL.

The macvlan creation succeeds when we filter out the ESP
feature flags in macvlan_fix_features(), so let's filter them
out like we're already filtering out ~NETIF_F_NETNS_LOCAL.
When XFRM support is added in the future, we can add the flags
into MACVLAN_FEATURES.

This same problem could crop up in the future with any other
new feature flags, so let's filter out any flags that aren't
defined as supported in macvlan.

Fixes: d77e38e6 ("xfrm: Add an IPsec hardware offloading API")
Reported-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

William Tu says:

====================
a couple of erspan fixes

The series fixes a couple of erspan issues.
The first patch adds the erspan v2 proto type to the ip6 tunnel lookup.
The second patch improves the error handling when users screws the
version number in metadata.  The final patch makes sure the skb has
enough headroom for pushing erspan header when xmit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds skb_cow_header() to ensure enough headroom
at ip6erspan_tunnel_xmit before pushing the erspan header
to the skb.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When users fill in incorrect erspan version number through
the struct erspan_metadata uapi, current code skips pushing
the erspan header but continue pushing the gre header, which
is incorrect.  The patch fixes it by returning error.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds the erspan v2 proto in ip6gre_tunnel_lookup
so the erspan v2 tunnel can be found correctly.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: ACL and mirroring fixes

The first patch fixes offload of rules using the 'pass' action. Instead
of continuing to evaluate lower priority rules, the binding is
terminated and the packet proceeds to the bridge and router blocks on
ingress, or goes out of the port on egress.

Second patch prevents the user from mirroring more than once from a
given {Port, Direction} as this is not supported by the device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The Spectrum ASIC doesn't support mirroring more than once from a single
binding point (which is a port-direction pair). Therefore detect that a
second binding of a given binding point is attempted.

To that end, extend struct mlxsw_sp_span_inspected_port to track whether
a given binding point is bound or not. Extend
mlxsw_sp_span_entry_port_find() to look for ports based on the full
unique key: port number, direction, and boundness.

Besides fixing the overt bug where configured mirrors are not offloaded,
this also fixes a more subtle bug: mlxsw_sp_span_inspected_port_del()
just defers to mlxsw_sp_span_entry_bound_port_find(), and that used to
find the first port with the right number (disregarding the type). Thus
by adding and removing egress and ingress mirrors in the right order,
one could trick the system into believing it has no egress mirrors when
in fact it did have some. That then caused that
mlxsw_sp_span_port_mtu_update() didn't update mirroring buffer when MTU
was changed.

Fixes: 763b4b70 ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For ok GACT action, TERMINATE binding_cmd should be used in action set
passed down to HW.

Fixes: b2925957 ("mlxsw: spectrum_flower: Offload "ok" termination action")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jason Wang says:

====================
Several fixes for vhost_net ptr_ring usage

This small series try to fix several bugs of ptr_ring usage in
vhost_net. Please review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit fc72d1d5 ("tuntap: XDP transmission"), we can
actually queueing XDP pointers in the pointer ring, so we should
examine the pointer type before freeing the pointer.

Fixes: fc72d1d5 ("tuntap: XDP transmission")
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We get pointer ring from the exported sock, this means we should keep
rx_ring and vq->private synced during both vq stop and backend set,
otherwise we may see stale rx_ring.

Fixes: c67df11f ("vhost_net: try batch dequing from skb array")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

KMSAN reported a use of uninit memory in vhost_net_buf_unproduce()
while trying to access n->vqs[VHOST_NET_VQ_TX].rx_ring:

==================================================================
BUG: KMSAN: use of uninitialized memory in vhost_net_buf_unproduce+0x7bb/0x9a0 drivers/vho
et.c:170
CPU: 0 PID: 3021 Comm: syz-fuzzer Not tainted 4.16.0-rc4+ #3853
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
 __dump_stack lib/dump_stack.c:17 [inline]
 dump_stack+0x185/0x1d0 lib/dump_stack.c:53
 kmsan_report+0x142/0x1f0 mm/kmsan/kmsan.c:1093
 __msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:676
 vhost_net_buf_unproduce+0x7bb/0x9a0 drivers/vhost/net.c:170
 vhost_net_stop_vq drivers/vhost/net.c:974 [inline]
 vhost_net_stop+0x146/0x380 drivers/vhost/net.c:982
 vhost_net_release+0xb1/0x4f0 drivers/vhost/net.c:1015
 __fput+0x49f/0xa00 fs/file_table.c:209
 ____fput+0x37/0x40 fs/file_table.c:243
 task_work_run+0x243/0x2c0 kernel/task_work.c:113
 tracehook_notify_resume include/linux/tracehook.h:191 [inline]
 exit_to_usermode_loop arch/x86/entry/common.c:166 [inline]
 prepare_exit_to_usermode+0x349/0x3b0 arch/x86/entry/common.c:196
 syscall_return_slowpath+0xf3/0x6d0 arch/x86/entry/common.c:265
 do_syscall_64+0x34d/0x450 arch/x86/entry/common.c:292
...
origin:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:303 [inline]
 kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:213
 kmsan_kmalloc_large+0x6f/0xd0 mm/kmsan/kmsan.c:392
 kmalloc_large_node_hook mm/slub.c:1366 [inline]
 kmalloc_large_node mm/slub.c:3808 [inline]
 __kmalloc_node+0x100e/0x1290 mm/slub.c:3818
 kmalloc_node include/linux/slab.h:554 [inline]
 kvmalloc_node+0x1a5/0x2e0 mm/util.c:419
 kvmalloc include/linux/mm.h:541 [inline]
 vhost_net_open+0x64/0x5f0 drivers/vhost/net.c:921
 misc_open+0x7b5/0x8b0 drivers/char/misc.c:154
 chrdev_open+0xc28/0xd90 fs/char_dev.c:417
 do_dentry_open+0xccb/0x1430 fs/open.c:752
 vfs_open+0x272/0x2e0 fs/open.c:866
 do_last fs/namei.c:3378 [inline]
 path_openat+0x49ad/0x6580 fs/namei.c:3519
 do_filp_open+0x267/0x640 fs/namei.c:3553
 do_sys_open+0x6ad/0x9c0 fs/open.c:1059
 SYSC_openat+0xc7/0xe0 fs/open.c:1086
 SyS_openat+0x63/0x90 fs/open.c:1080
 do_syscall_64+0x2f1/0x450 arch/x86/entry/common.c:287
==================================================================

Fixes: c67df11f ("vhost_net: try batch dequing from skb array")
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This enables AVE_GI_RXDROP interrupt factor. This factor indicates
depletion of Rx descriptors and the handler counts the number
of dropped packets.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As well as the basic conversion, I noticed that a lot of the
SCTP code checks gso_type without first checking skb_is_gso()
so I have added that where appropriate.

Also, document the helper.

Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

A tun device type can trivially be set to arbitrary value using
TUNSETLINK ioctl().

Therefore, lowpan_device_event() must really check that ieee802154_ptr
is not NULL.

Fixes: 2c88b528 ("ieee802154: 6lowpan: remove check on null")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following slab-out-of-bounds kasan report in
ndisc_fill_redirect_hdr_option when the incoming ipv6 packet is not
linear and the accessed data are not in the linear data region of orig_skb.

[ 1503.122508] ==================================================================
[ 1503.122832] BUG: KASAN: slab-out-of-bounds in ndisc_send_redirect+0x94e/0x990
[ 1503.123036] Read of size 1184 at addr ffff8800298ab6b0 by task netperf/1932

[ 1503.123220] CPU: 0 PID: 1932 Comm: netperf Not tainted 4.16.0-rc2+ #124
[ 1503.123347] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.10.2-2.fc27 04/01/2014
[ 1503.123527] Call Trace:
[ 1503.123579]  <IRQ>
[ 1503.123638]  print_address_description+0x6e/0x280
[ 1503.123849]  kasan_report+0x233/0x350
[ 1503.123946]  memcpy+0x1f/0x50
[ 1503.124037]  ndisc_send_redirect+0x94e/0x990
[ 1503.125150]  ip6_forward+0x1242/0x13b0
[...]
[ 1503.153890] Allocated by task 1932:
[ 1503.153982]  kasan_kmalloc+0x9f/0xd0
[ 1503.154074]  __kmalloc_track_caller+0xb5/0x160
[ 1503.154198]  __kmalloc_reserve.isra.41+0x24/0x70
[ 1503.154324]  __alloc_skb+0x130/0x3e0
[ 1503.154415]  sctp_packet_transmit+0x21a/0x1810
[ 1503.154533]  sctp_outq_flush+0xc14/0x1db0
[ 1503.154624]  sctp_do_sm+0x34e/0x2740
[ 1503.154715]  sctp_primitive_SEND+0x57/0x70
[ 1503.154807]  sctp_sendmsg+0xaa6/0x1b10
[ 1503.154897]  sock_sendmsg+0x68/0x80
[ 1503.154987]  ___sys_sendmsg+0x431/0x4b0
[ 1503.155078]  __sys_sendmsg+0xa4/0x130
[ 1503.155168]  do_syscall_64+0x171/0x3f0
[ 1503.155259]  entry_SYSCALL_64_after_hwframe+0x42/0xb7

[ 1503.155436] Freed by task 1932:
[ 1503.155527]  __kasan_slab_free+0x134/0x180
[ 1503.155618]  kfree+0xbc/0x180
[ 1503.155709]  skb_release_data+0x27f/0x2c0
[ 1503.155800]  consume_skb+0x94/0xe0
[ 1503.155889]  sctp_chunk_put+0x1aa/0x1f0
[ 1503.155979]  sctp_inq_pop+0x2f8/0x6e0
[ 1503.156070]  sctp_assoc_bh_rcv+0x6a/0x230
[ 1503.156164]  sctp_inq_push+0x117/0x150
[ 1503.156255]  sctp_backlog_rcv+0xdf/0x4a0
[ 1503.156346]  __release_sock+0x142/0x250
[ 1503.156436]  release_sock+0x80/0x180
[ 1503.156526]  sctp_sendmsg+0xbb0/0x1b10
[ 1503.156617]  sock_sendmsg+0x68/0x80
[ 1503.156708]  ___sys_sendmsg+0x431/0x4b0
[ 1503.156799]  __sys_sendmsg+0xa4/0x130
[ 1503.156889]  do_syscall_64+0x171/0x3f0
[ 1503.156980]  entry_SYSCALL_64_after_hwframe+0x42/0xb7

[ 1503.157158] The buggy address belongs to the object at ffff8800298ab600
                which belongs to the cache kmalloc-1024 of size 1024
[ 1503.157444] The buggy address is located 176 bytes inside of
                1024-byte region [ffff8800298ab600, ffff8800298aba00)
[ 1503.157702] The buggy address belongs to the page:
[ 1503.157820] page:ffffea0000a62a00 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[ 1503.158053] flags: 0x4000000000008100(slab|head)
[ 1503.158171] raw: 4000000000008100 0000000000000000 0000000000000000 00000001800e000e
[ 1503.158350] raw: dead000000000100 dead000000000200 ffff880036002600 0000000000000000
[ 1503.158523] page dumped because: kasan: bad access detected

[ 1503.158698] Memory state around the buggy address:
[ 1503.158816]  ffff8800298ab900: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1503.158988]  ffff8800298ab980: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1503.159165] >ffff8800298aba00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 1503.159338]                    ^
[ 1503.159436]  ffff8800298aba80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 1503.159610]  ffff8800298abb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 1503.159785] ==================================================================
[ 1503.159964] Disabling lock debugging due to kernel taint

The test scenario to trigger the issue consists of 4 devices:
- H0: data sender, connected to LAN0
- H1: data receiver, connected to LAN1
- GW0 and GW1: routers between LAN0 and LAN1. Both of them have an
  ethernet connection on LAN0 and LAN1
On H{0,1} set GW0 as default gateway while on GW0 set GW1 as next hop for
data from LAN0 to LAN1.
Moreover create an ip6ip6 tunnel between H0 and H1 and send 3 concurrent
data streams (TCP/UDP/SCTP) from H0 to H1 through ip6ip6 tunnel (send
buffer size is set to 16K). While data streams are active flush the route
cache on HA multiple times.
I have not been able to identify a given commit that introduced the issue
since, using the reproducer described above, the kasan report has been
triggered from 4.14 and I have not gone back further.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stephen Hemminger says:

====================
hv_netvsc: fix multicast flags and sync

This set of patches deals with the handling of multicast flags
and addresses in transparent VF mode. The recent set of patches
(in linux-net) had a couple of bugs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The dev_uc/mc_sync calls need to have the device address list
locked. This was spotted by running with lockdep enabled.

Fixes: bee9d41b ("hv_netvsc: propagate rx filters to VF")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rx_mode operation handler is different than other callbacks
in that is not always called with rtnl held. Therefore use
RCU to ensure that references are valid.

Fixes: bee9d41b ("hv_netvsc: propagate rx filters to VF")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netvsc driver can get repeated calls to netvsc_rx_mode during
network setup; each of these calls ends up scheduling the lower
layers to update tha packet filter. This update requires an
request/response to the host. So avoid doing this if we already
know that the correct packet filter value is set.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The recent change to not always enable all multicast and broadcast
was broken; meant to set filter, not change flags.

Fixes: 009f766c ("hv_netvsc: filter multicast/broadcast")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2018-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo:

====================
wireless-drivers fixes for 4.16

Quote a few fixes as I have not been able to send a pull request
earlier. Most of the fixes for iwlwifi but also few others, nothing
really standing out though.

iwlwifi

* fix a bogus warning when freeing a TFD

* fix severe throughput problem with 9000 series

* fix for a bug that caused queue hangs in certain situations

* fix for an issue with IBSS

* fix an issue with rate-scaling in AP-mode

* fix Channel Switch Announcement (CSA) issues with count 0 and 1

* some firmware debugging fixes

* remov a wrong error message when removing keys

* fix a firmware sysassert most usually triggered in IBSS

* a couple of fixes on multicast queues

* a fix with CCMP 256

rtlwifi

* fix loss of signal for rtl8723be

brcmfmac

* add possibility to obtain firmware error

* fix P2P_DEVICE ethernet address generation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pretty minor: just SKB_GSO_TCP  -> SKB_GSO_TCPV4 and
                   SKB_GSO_TCP6 -> SKB_GSO_TCPV6.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The __send_and_alloc_skb() receives a skb ptr as a parameter but in
case it fails the skb is not valid:
- Send failed and released the skb internally.
- Allocation failed.

The current code tries to release the skb in case of failure which
causes redundant freeing.

Fixes: 9b00cf2d ("team: implement multipart netlink messages for options transfers")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-03-08

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix various BPF helpers which adjust the skb and its GSO information
   with regards to SCTP GSO. The latter is a special case where gso_size
   is of value GSO_BY_FRAGS, so mangling that will end up corrupting
   the skb, thus bail out when seeing SCTP GSO packets, from Daniel(s).

2) Fix a compilation error in bpftool where BPF_FS_MAGIC is not defined
   due to too old kernel headers in the system, from Jiri.

3) Increase the number of x64 JIT passes in order to allow larger images
   to converge instead of punting them to interpreter or having them
   rejected when the interpreter is not built into the kernel, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In Cilium some of the main programs we run today are hitting 9 passes
on x64's JIT compiler, and we've had cases already where we surpassed
the limit where the JIT then punts the program to the interpreter
instead, leading to insertion failures due to CONFIG_BPF_JIT_ALWAYS_ON
or insertion failures due to the prog array owner being JITed but the
program to insert not (both must have the same JITed/non-JITed property).

One concrete case the program image shrunk from 12,767 bytes down to
10,288 bytes where the image converged after 16 steps. I've measured
that this took 340us in the JIT until it converges on my i7-6600U. Thus,
increase the original limit we had from day one where the JIT covered
cBPF only back then before we run into the case (as similar with the
complexity limit) where we trip over this and hit program rejections.
Also add a cond_resched() into the compilation loop, the JIT process
runs without any locks and may sleep anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Do not set 'needs_free_netdev' as we do call free_netdev
for mgmt net devices, doing both hits BUG_ON.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

instantiation of VF's on different adapters fails, copy
adapter index and chip type to PF0-3 adapter instances
to fix the issue.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Starting with v4.16-rc1 we've been seeing a higher than usual number
of requests for the kernel to load networking modules, even on events
which shouldn't trigger a module load (e.g. ioctl(TCGETS)).  Stephen
Smalley suggested the problem may lie in commit 44c02a2c
("dev_ioctl(): move copyin/copyout to callers") which moves changes
the network dev_ioctl() function to always call dev_load(),
regardless of the requested ioctl.

This patch moves the dev_load() calls back into the individual ioctls
while preserving the rest of the original patch.
Reported-by: Dominick Grift <dac.override@gmail.com>
Suggested-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the connection is aborted, there is no point in
keeping the packets on the write queue until the connection
is closed.

Similar to a27fd7a8 ('tcp: purge write queue upon RST'),
this is essential for a correct MSG_ZEROCOPY implementation,
because userspace cannot call close(fd) before receiving
zerocopy signals even when the connection is aborted.

Fixes: f214f915 ("tcp: enable MSG_ZEROCOPY")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>