- 26 Aug, 2021 2 commits
-
-
John Clements authored
Update XGMI RAS to support error query on aldebaran Reviewed-by:
Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by:
John Clements <john.clements@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com>
-
Sean Keely authored
On systems with multiple SH per SE compute_static_thread_mgmt_se# is split into independent masks, one for each SH, in the upper and lower 16 bits. We need to detect this and apply cu masking to each SH. The cu mask bits are assigned first to each SE, then to alternate SHs, then finally to higher CU id. This ensures that the maximum number of SPIs are engaged as early as possible while balancing CU assignment to each SH. v2: Use max SH/SE rather than max SH in cu_per_sh. v3: Fix comment blocks, ensure se_mask is initially zero filled, and correctly assign se.sh.cu positions to unset bits in cu_mask. Signed-off-by:Sean Keely <Sean.Keely@amd.com> Reviewed-by:
Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by:
-
- 25 Aug, 2021 4 commits
-
-
Yifan Zhang authored
amdgpu_bo_get_preferred_pin_domain is used for page tables creation, which is not involved with page pinning. And it is used in more cases than display scanout, modify its documentation as well. Signed-off-by:
Yifan Zhang <yifan1.zhang@amd.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Evan Quan authored
As those _sw_fini() APIs follow just after _suspend() APIs. And the cancel_delayed_work_sync was already called in latter. Signed-off-by:
Evan Quan <evan.quan@amd.com> Reviewed-by:
Guchun Chen <guchun.chen@amd.com> Signed-off-by:
-
Evan Quan authored
This is a supplement for commit below: "drm/amdgpu: add missing cleanups for Polaris12 UVD/VCE on suspend". Signed-off-by:
-
Evan Quan authored
Perform proper cleanups on UVD/VCE suspend: powergate enablement, clockgating enablement and dpm disablement. This can fix some hangs observed on suspending when UVD/VCE still using(e.g. issue "pm-suspend" when video is still playing). Signed-off-by:
xinhui pan <xinhui.pan@amd.com> Reviewed-by:
-
- 24 Aug, 2021 13 commits
-
-
Philip Yang authored
Restore retry fault or prefetch range, or restore svm range after eviction to map range to GPU with correct read or write access permission. Range may includes multiple VMAs, update GPU page table with offset of prange, number of pages for each VMA according VMA access permission. Signed-off-by:
Philip Yang <Philip.Yang@amd.com> Reviewed-by:
-
Philip Yang authored
Check range access permission to restore GPU retry fault, if GPU retry fault on address which belongs to VMA, and VMA has no read or write permission requested by GPU, failed to restore the address. The vm fault event will pass back to user space. Signed-off-by:
-
John Clements authored
Resolve bug querying error on unsupported ASIC Reviewed-by:
-
John Clements authored
Add MCA specific IP blocks targetting RAS features Reviewed-by:
-
Praful Swarnakar authored
[Why] Recent HDMI2.0 HF1-1 V-Swing testing showed that logging deep color status helps in validation of testcase. [How] Add logging based on various color depths and pixel encoding formats. Signed-off-by:
Praful Swarnakar <Praful.Swarnakar@amd.com> Reviewed-by:
Hersen Wu <hersenwu@amd.com> Signed-off-by:
-
Candice Li authored
Signed-off-by:
Candice Li <candice.li@amd.com> Reviewed-by:
-
Candice Li authored
Adding name field back to ras_common_if to work around error injection failure with amdgpuras tool. Signed-off-by:
-
Borislav Petkov authored
Building a randconfig here triggered: ERROR: modpost: "pm_suspend_target_state" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined! because the module export of that symbol happens in kernel/power/suspend.c which is enabled with CONFIG_SUSPEND. The ifdef guards in amdgpu_acpi_is_s0ix_supported(), however, test for CONFIG_PM_SLEEP which is defined like this: config PM_SLEEP def_bool y depends on SUSPEND || HIBERNATE_CALLBACKS and that randconfig has: # CONFIG_SUSPEND is not set CONFIG_HIBERNATE_CALLBACKS=y leading to the module export missing. Change the ifdeffery to depend directly on CONFIG_SUSPEND. Fixes: 5706cb3c ("drm/amdgpu: fix checking pmops when PM_SLEEP is not enabled") Reviewed-by:Lijo Lazar <lijo.lazar@amd.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/YSP6Lv53QV0cOAsd@zn.tnicSigned-off-by:
-
Christophe JAILLET authored
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below. It has been compile tested. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Reviewed-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Christophe JAILLET authored
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below. It has been compile tested. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Reviewed-by:
-
Mukul Joshi authored
Program trap handler settings to enable CWSR with software scheduler on Aldebaran and Arcturus. Signed-off-by:
Mukul Joshi <mukul.joshi@amd.com> Reviewed-by:
Amber Lin <Amber.Lin@amd.com> Signed-off-by:
-
Shashank Sharma authored
This patch limits the ref_div_max value to 100, during the calculation of PLL feedback reference divider. With current value (128), the produced fb_ref_div value generates unstable output at particular frequencies. Radeon driver limits this value at 100. On Oland, when we try to setup mode 2048x1280@60 (a bit weird, I know), it demands a clock of 221270 Khz. It's been observed that the PLL calculations using values 128 and 100 are vastly different, and look like this: +------------------------------------------+ |Parameter |AMDGPU |Radeon | | | | | +-------------+----------------------------+ |Clock feedback | | |divider max | 128 | 100 | |cap value | | | | | | | | | | | +------------------------------------------+ |ref_div_max | | | | | 42 | 20 | | | | | | | | | +------------------------------------------+ |ref_div | 42 | 20 | | | | | +------------------------------------------+ |fb_div | 10326 | 8195 | +------------------------------------------+ |fb_div | 1024 | 163 | +------------------------------------------+ |fb_dev_p | 4 | 9 | |frac fb_de^_p| | | +----------------------------+-------------+ With ref_div_max value clipped at 100, AMDGPU driver can also drive videmode 2048x1280@60 (221Mhz) and produce proper output without any blanking and distortion on the screen. PS: This value was changed from 128 to 100 in Radeon driver also, here: https://github.com/freedesktop/drm-tip/commit/4b21ce1b4b5d262e7d4656b8ececc891fc3cb806 V1: Got acks from: Acked-by:
Shashank Sharma <shashank.sharma@amd.com> Signed-off-by:
-
Eric Yang authored
[Why] A cleaner solution, only done once on boot. [How] Remove previous workaround and configure an extra vmid one time on boot Reviewed-by:
Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com> Acked-by:
Solomon Chiu <solomon.chiu@amd.com> Signed-off-by:
Eric Yang <Eric.Yang2@amd.com> Tested-by:
Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by:
-
- 20 Aug, 2021 3 commits
-
-
Michel Dänzer authored
schedule_delayed_work does not push back the work if it was already scheduled before, so amdgpu_device_delay_enable_gfx_off ran ~100 ms after the first time GFXOFF was disabled and re-enabled, even if GFXOFF was disabled and re-enabled again during those 100 ms. This resulted in frame drops / stutter with the upcoming mutter 41 release on Navi 14, due to constantly enabling GFXOFF in the HW and disabling it again (for getting the GPU clock counter). To fix this, call cancel_delayed_work_sync when the disable count transitions from 0 to 1, and only schedule the delayed work on the reverse transition, not if the disable count was already 0. This makes sure the delayed work doesn't run at unexpected times, and allows it to be lock-free. v2: * Use cancel_delayed_work_sync & mutex_trylock instead of mod_delayed_work. v3: * Make amdgpu_device_delay_enable_gfx_off lock-free (Christian König) v4: * Fix race condition between amdgpu_gfx_off_ctrl incrementing adev->gfx.gfx_off_req_count and amdgpu_device_delay_enable_gfx_off checking for it to be 0 (Evan Quan) Cc: stable@vger.kernel.org Reviewed-by:
Michel Dänzer <mdaenzer@redhat.com> Signed-off-by:
-
Christian König authored
For some reason we run into an use case where a BO is already pinned into GTT, but should be pinned into VRAM|GTT again. Handle that case gracefully as well. Reviewed-by:
-
Evan Quan authored
Considering Arcturus is a dedicated ASIC for computing, it will be more proper to drop the support for fan speed reading and setting. That's on the TODO list. Signed-off-by:
Rui Teng <rui.teng@amd.com> Reviewed-by:
-
- 18 Aug, 2021 9 commits
-
-
Lukas Bulwahn authored
Commit 04ed8459 ("drm/amdgpu: remove chash") removes the chash architecture and its corresponding config CHASH. There is still a reference to CHASH in the config DRM_AMDGPU in ./drivers/gpu/drm/Kconfig. Remove this obsolete reference to config CHASH. Signed-off-by:
Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by:
-
Colin Ian King authored
There is a spelling mistake in a dev_err error message. Fix it. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
YuBiao Wang authored
[Why] In some cases when we unload driver, warning call trace will show up in vram_mgr_fini which claims that LRU is not empty, caused by the ttm bo inside delay deleted queue. [How] We should flush delayed work to make sure the delay deleting is done. Signed-off-by:
YuBiao Wang <YuBiao.Wang@amd.com> Reviewed-by:
Andrey Grodzovsky <andrey.grodzovsky@amd.com> Signed-off-by:
-
Candice Li authored
Signed-off-by:
-
Hawking Zhang authored
aldebaran supports up to 16 xgmi physical nodes. Signed-off-by:
-
Evan Quan authored
We have a S3 issue on that SKU with BACO enabled. Will bring back this when that root caused. Signed-off-by:
-
Zhan Liu authored
[why] dcn301_calculate_wm_and_dl() causes flickering when external monitor is connected. This issue has been fixed before by commit 0e4c0ae5 ("drm/amdgpu/display: drop dcn301_calculate_wm_and_dl for now"), however part of the fix was gone after commit 2cbcb78c ("Merge tag 'amd-drm-next-5.13-2021-03-23' of https://gitlab.freedesktop.org/agd5f/linux into drm-next"). [how] Use dcn30_calculate_wm_and_dlg() instead as in the original fix. Fixes: 2cbcb78c ("Merge tag 'amd-drm-next-5.13-2021-03-23' of https://gitlab.freedesktop.org/agd5f/linux into drm-next") Signed-off-by:
Nikola Cornij <nikola.cornij@amd.com> Reviewed-by:
Zhan Liu <zhan.liu@amd.com> Tested-by:
Oliver Logush <oliver.logush@amd.com> Signed-off-by:
-
Zhigang Luo authored
MMSCH 1.0 doesn't have major/minor version, only verison. Signed-off-by:
Zhigang Luo <zhigang.luo@amd.com> Reviewed by Shaoyun.liu <Shaoyun.liu@amd.com> Signed-off-by:
-
Jonathan Kim authored
The TA has a limit to the amount of data that can be retrieved from GET_TOPOLOGY. For setups that exceed this limit, the xGMI topology needs to be re-initialized and data needs to be re-fetched from the extended link records by setting a flag in the shared command buffer. The number of hops and the number of links must be accumulated by the driver. Other data points are all fetched from the first request. Because the TA has already exceeded its link record limit, it cannot hold bidirectional information. Otherwise the driver would have to do more than two fetches so the driver has to reflect the topology information in the opposite direction. v2: squashed with internal reviewed fix Signed-off-by:
Jonathan Kim <jonathan.kim@amd.com> Reviewed-by:
-
- 16 Aug, 2021 9 commits
-
-
Nathan Chancellor authored
Clang + -Wimplicit-fallthrough warns: drivers/gpu/drm/radeon/radeon_fb.c:170:2: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough] default: ^ drivers/gpu/drm/radeon/radeon_fb.c:170:2: note: insert 'break;' to avoid fall-through default: ^ break; 1 warning generated. Clang's version of this warning is a little bit more pedantic than GCC's. Add the missing break to satisfy it to match what has been done all over the kernel tree. Reviewed-by:Nathan Chancellor <nathan@kernel.org> Signed-off-by:
-
Aric Cyr authored
This version brings along following fixes: - Ensure DCN save init registers after VM setup - Fix multi-display support for idle opt workqueue - Use vblank control events for PSR enable/disable - Create default dc_sink when fail reading EDID under MST Acked-by:
Wayne Lin <wayne.lin@amd.com> Signed-off-by:
Aric Cyr <aric.cyr@amd.com> Tested-by:
-
Anthony Koo authored
Acked-by:
Anthony Koo <Anthony.Koo@amd.com> Tested-by:
-
Nicholas Kazlauskas authored
[Why] Compilation of the workqueue fails if not building with the DCN config option set. [How] Guard calls to the flush with the DCN config option to fix the build. Reviewed-by:
Roman Li <Roman.Li@amd.com> Acked-by:
-
Jake Wang authored
[Why] DM initializes VM context after DMCUB initialization. This results in loss of DCN_VM_CONTEXT registers after z10. [How] Notify DMCUB when VM setup is complete, and have DMCUB save init registers. v2: squash in CONFIG_DRM_AMD_DC_DCN3_1 fix Reviewed-by:
Jake Wang <haonan.wang2@amd.com> Tested-by:
-
Nicholas Kazlauskas authored
[Why] PSR can disable the HUBP along with the OTG when PSR is active. We'll hit a pageflip timeout when the OTG is disable because we're no longer updating the CRTC vblank counter and the pflip high IRQ will not fire on the flip. In order to flip the page flip timeout occur we should modify the enter/exit conditions to match DRM requirements. [How] Use our deferred handlers for DRM vblank control to notify DMCU(B) when it can enable or disable PSR based on whether vblank is disabled or enabled respectively. We'll need to pass along the stream with the notification now because we want to access the CRTC state while the CRTC is locked to get the stream state prior to the commit. Retain a reference to the stream so it remains safe to continue to access and release that reference once we're done with it. Enable/disable logic follows what we were previously doing in update_planes. The workqueue has to be flushed before programming streams or planes to ensure that we exit out of idle optimizations and PSR before these events occur if necessary. To keep the skip count logic the same to avoid FBCON PSR enablement requires copying the allow condition onto the DM IRQ parameters - a field that we can actually access from the worker. Reviewed-by:
-
Nicholas Kazlauskas authored
[Why] The current implementation for idle optimization support only has a single work item that gets reshuffled into the system workqueue whenever we receive an enable or disable event. We can have mismatched events if the work hasn't been processed or if we're getting control events from multiple displays at once. This fixes this issue and also makes the implementation usable for PSR control - which will be addressed in another patch. [How] We need to be able to flush remaining work out on demand for driver stop and psr disable so create a driver specific workqueue instead of using the system one. The workqueue will be single threaded to guarantee the ordering of enable/disable events. Refactor the queue to allocate the control work and deallocate it after processing it. Pass the acrtc directly to make it easier to handle psr enable/disable in a later patch. Rename things to indicate that it's not just MALL specific. Reviewed-by:
-
Wayne Lin authored
[Why] While reading remote EDID via Startech 1-to-4 hub, occasionally we won't get response in time and won't light up corresponding monitor. Ideally, we can still add generic modes for userspace to choose to try to light up the monitor and which is done in drm_helper_probe_single_connector_modes(). So the main problem here is that we fail .mode_valid since we don't create remote dc_sink for this case. [How] Also add default dc_sink if we can't get the EDID. Reviewed-by:
-
Evan Quan authored
These registers have different address from other SMU V11 ASICs. Signed-off-by:
-
