This commit adds support to the eeprom_93x46 driver allowing a GPIO line
to function as a 'select' or 'enable' signal prior to accessing the
EEPROM.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Tested-by: Chris Healy <chris.healy@zii.aero>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Atmel devices in this family have some quirks not found in other similar
chips - they do not support a sequential read of the entire EEPROM
contents, and the control word sent at the start of each operation
varies in bit length.

This commit adds quirk support to the driver and modifies the read
implementation to support non-sequential reads for consistency with
other misc/eeprom drivers.

Tested on a custom Freescale VF610-based platform, with an AT93C46D
device attached via dspi2.  The spi-gpio driver was used to allow the
necessary non-byte-sized transfers.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Tested-by: Chris Healy <chris.healy@zii.aero>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

w1_process() calls try_to_freeze(), but the thread doesn't mark itself
freezable through set_freezable(), so the try_to_freeze() call is useless.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The current code fails to nvmem_cell_drop(cells[0]) - even worse, if
the loop above fails already at i==0, we'll enter an essentially
infinite loop doing nvmem_cell_drop on cells[-1], cells[-2], ... which
is unlikely to end well.

Also, we're not freeing the temporary backing array cells on the error
path.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When CONFIG_NWBUTTON_REBOOT is disabled, we get a warning about
an unused variable:

drivers/char/nwbutton.c:37:12: warning: 'reboot_count' defined but not used [-Wunused-variable]
 static int reboot_count = NUM_PRESSES_REBOOT; /* Number of presses to reboot */

Using if(IS_ENABLED()) instead of #ifdef around the user makes the
code nicer to read and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch modifies the MIC host and card drivers to start using the
VOP driver. The MIC host and card drivers now implement the VOP bus
operations and register a VOP device on the VOP bus. MIC driver stack
documentation is also updated to include the new VOP driver.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch moves the virtio specific debugfs hooks previously in
mic_debugfs.c in the MIC host driver into the VOP driver. The
Kconfig/Makefile is also updated to allow building the VOP driver.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch moves virtio functionality from the MIC card driver into a
separate hardware independent Virtio Over PCIe (VOP) driver. This
functionality was introduced in commit 2141c7c5 ("Intel MIC Card
Driver Changes for Virtio Devices.") in
drivers/misc/mic/card/mic_virtio.c. Apart from being moved into a
separate driver the functionality is essentially unchanged. See the
above mentioned commit for a description of this functionality.
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch moves virtio functionality from the MIC host driver into a
separate hardware independent Virtio Over PCIe (VOP) driver. This
functionality was introduced in commit f69bcbf3 ("Intel MIC Host
Driver Changes for Virtio Devices.") in
drivers/misc/mic/host/mic_virtio.c. Apart from being moved into a
separate driver the functionality is essentially unchanged. See the
above mentioned commit for a description of this functionality.
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds VOP driver data structures used in subsequent
patches. These data structures are refactored from similar data
structures used in the virtio parts of previous MIC host and card
drivers.
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Virtio Over PCIe (VOP) bus abstracts the low level hardware
details like interrupts and mapping remote memory so that the same VOP
driver can work without changes with different MIC host or card
drivers as long as the hardware bus operations are implemented. The
VOP driver registers itself on the VOP bus. The base PCIe drivers
implement the bus ops and register VOP devices on the bus, resulting
in the VOP driver being probed with the VOP devices. This allows the
VOP functionality to be shared between multiple generations of Intel
MIC products.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch deletes the virtio functionality from the MIC X100 card
driver. A subsequent patch will re-enable this functionality by
consolidating the hardware independent logic in a new Virtio over PCIe
(VOP) driver.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch deletes the virtio functionality from the MIC X100 host
driver. A subsequent patch will re-enable this functionality by
consolidating the hardware independent logic in a new Virtio over PCIe
(VOP) driver.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The file wd.c was remove from the driver by commit
commit fdd9b865 ("mei: wd: drop the watchdog code from the core mei
driver")

Unfortunately it came back by mistake in rebasing in the commit
commit 06ee536b ("mei: fill file pointer in read cb for fixed
address client")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The kernel sometimes fails to link when lkdrm is built-in and
compiled with clang:

relocation truncated to fit: R_ARM_THM_CALL against `.bss'

The reason here is that a relocation from .text to .bss fails to
generate a trampoline because .bss is not an executable section.

Marking the function 'noinline' turns the relative branch to .bss
into an absolute branch to the function argument, and that works
fine.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit implements bindings in the eeprom_93xx46 driver allowing
device word size and read-only attributes to be specified via
devicetree.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Tested-by: Chris Healy <chris.healy@zii.aero>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit documents bindings to be added to the eeprom_93xx46 driver
which will allow:

  - Device word size and read-only attributes to be specified.
  - A device-specific compatible string for use with Atmel AT93C46D
    EEPROMs.
  - Specifying a GPIO line to function as a 'select' or 'enable' signal
    prior to accessing the EEPROM.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Chris Healy <chris.healy@zii.aero>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Compatible at93xx46 devices from both Microchip and Atmel expect a
word-based address, regardless of whether the device is strapped for 8-
or 16-bit operation.  However, the offset parameter passed in when
reading or writing at a specific location is always specified in terms
of bytes.

This commit fixes 16-bit read and write accesses by shifting the offset
parameter to account for this difference between a byte offset and a
word-based address.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Tested-by: Chris Healy <chris.healy@zii.aero>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

No need to use use continuous memory, it may be fail
when memory deeply fragmented.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Xia Qing <saberlily.xia@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Compat ioctl is already introduced in drivers/char/ppdev.c in order to
fix y2038 issue for PP[GS]ETTIME. There is no need to define these
here.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The arg of ioctl in ppdev is the pointer of integer except the
timeval in PPSETTIME, PPGETTIME. Different size of timeval
is already supported by the previous patches. So, it is safe
to add compat support.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The y2038 issue for ppdev is changes of timeval in the ioctl
(PPSETTIME and PPGETTIME). The size of struct timeval changes from
8bytes to 16bytes due to the changes of time_t. It lead to the
changes of the command of ioctl, e.g. for PPGETTIME, We have:

on 32-bit (old): 0x80087095
on 32-bit (new): 0x80107095
on 64-bit      : 0x80107095

This patch define these two ioctl commands to support the 32bit
and 64bit time_t application at the same time. And, introduce
pp_set_timeout to remove some duplicated code.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Simplify a few of the *generic* shared dev_warn() and dev_dbg()
print messages for three reasons:

0) Historically firmware_class code was added to help
   get device driver firmware binaries but these days
   request_firmware*() helpers are being repurposed for
   general *system data* needed by the kernel.

1) This will also help generalize shared code as much as possible
   later in the future in consideration for a new extensible firmware
   API which will enable to separate usermode helper code out as much
   as possible.

2) Kees Cook pointed out the the prints already have the device
   associated as dev_*() helpers are used, that should help identify
   the user and case in which the helpers are used. That should provide
   enough context and simplifies the messages further.

v4: generalize debug/warn messages even further as suggested by
    Kees Cook.

Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Vojtěch Pavlík <vojtech@suse.cz>
Cc: Kyle McMartin <kyle@kernel.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Removed braces from single statement if condition.Fixed checkpatch.pl
warning.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some array of const char are not set as const.
This patch fix that.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for more than 128 peripherals by taking a lazy
caching approach to the mapping tables. Instead of reading and
caching the tables at boot given some fixed size, read them and
cache them on an as needed basis. We still assume a max size of
512 peripherals, trading off some space for simplicity.

Based on a patch by Gilad Avidov <gavidov@codeaurora.org> and
Sagar Dharia <sdharia@codeaurora.org>.

Cc: Gilad Avidov <gavidov@codeaurora.org>
Cc: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hdq_usecount was set to zero after a successful read, so
omap_hdq_put could not properly free resources which leads
e.g. to increasing usecounts in lsmod output
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use kobj_to_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use kobj_to_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Acked-by: Martyn Welch <martyn@welchs.me.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1) Make the include file to sort from order
2) clean up the driver to make more readability

Let's clean up such trivial details.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

this pacthset try to fix the code style for sunxi.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmem providers have restrictions on register strides, so return error
when users attempt to read/write buffers with sizes which are less
than word size.

Without this patch the userspace would continue to try as it does not
get any error from the nvmem core, resulting in a hang or endless loop
in userspace.
Reported-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add Mediatek EFUSE driver to access hardware data like
thermal sensor calibration or HDMI impedance.
Signed-off-by: Andrew-CT Chen <andrew-ct.chen@mediatek.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add Mediatek MT8173 EFUSE Devicetree binding file
Signed-off-by: Andrew-CT Chen <andrew-ct.chen@mediatek.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit adds support for NXP LPC18xx EEPROM memory found in NXP
LPC185x/3x and LPC435x/3x/2x/1x devices.

EEPROM size is 16384 bytes and it can be entirely read and
written/erased with 1 word (4 bytes) granularity. The last page
(128 bytes) contains the EEPROM initialization data and is not writable.

Erase/program time is less than 3ms. The EEPROM device requires a
~1500 kHz clock (min 800 kHz, max 1600 kHz) that is generated dividing
the system bus clock by the division factor, contained in the divider
register (minus 1 encoded).

EEPROM will be kept in Power Down mode except during read/write calls.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the devicetree binding document for NXP LPC18xx EEPROM memory.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use kobj_to_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use kobj_to_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>