- 13 Jun, 2017 40 commits
-
-
Florian Fainelli authored
Introduce a helper function which will return a reference to the CPU port used in a dsa_switch_tree. Right now this is a singleton, but this will change once we introduce multi-CPU port support, so ease the transition by converting the affected code paths. Reviewed-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
In preparation for supporting multiple CPU ports with DSA, have the dsa_port structure know which CPU it is associated with. This will be important in order to make sure the correct CPU is used for transmission of the frames. If not for functional reasons, for performance (e.g: load balancing) and forwarding decisions. Reviewed-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
Relocate master_ethtool_ops and master_orig_ethtool_ops into struct dsa_port in order to be both consistent, and make things self contained within the dsa_port structure. This is a preliminary change to supporting multiple CPU port interfaces. Reviewed-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
In preparation for supporting multiple CPU ports, remove dst->master_netdev and ds->master_netdev and replace them with only one instance of the common object we have for a port: struct dsa_port::netdev. ds->master_netdev is currently write only and would be helpful in the case where we have two switches, both with CPU ports, and also connected within each other, which the multi-CPU port patch series would address. While at it, introduce a helper function used in net/dsa/slave.c to immediately get a reference on the master network device called dsa_master_netdev(). Reviewed-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ganesh Goudar authored
If SF bit is not cleared in PL_INT_CAUSE, subsequent non-data interrupts are not raised. Enable SF bit in Global Interrupt Mask and handle it as non-fatal and hence eventually clear it. Signed-off-by:
Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by:
Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jon Mason authored
The of_mdio_parse_addr() helper function is useful to other code, but the module dependency chain causes issues. To work around this, we can move of_mdio_parse_addr() to be an inline function in the header file. This gets rid of the dependencies and still allows for the reuse of code. Reported-by:
Liviu Dudau <liviu@dudau.co.uk> Signed-off-by:
Jon Mason <jon.mason@broadcom.com> Fixes: 342fa196 ("mdio: mux: make child bus walking more permissive and errors more verbose") Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jesper Dangaard Brouer authored
The selftests depend on using the shell exit code as a mean of detecting the success or failure of test-binary executed. The appropiate output "[PASS]" or "[FAIL]" in generated by tools/testing/selftests/lib.mk. Notice that the exit code is masked with 255. Thus, be careful if using the number of errors as the exit code, as 256 errors would be seen as a success. There are two standard defined exit(3) codes: /usr/include/stdlib.h #define EXIT_FAILURE 1 /* Failing exit status. */ #define EXIT_SUCCESS 0 /* Successful exit status. */ Fix test_verifier.c to not use the negative value of variable "results", but instead return EXIT_FAILURE. Fix test_align.c and test_progs.c to actually use exit codes, before they were always indicating success regardless of results. Signed-off-by:
Jesper Dangaard Brouer <brouer@redhat.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Reviewed-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Zhang Shengju authored
Remove unnecessary setting of flag IFF_BROADCAST, since ether_setup already does this. Signed-off-by:
Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Johannes Berg authored
Use the recently introduced helper to replace the pattern of skb_put() && memset(), this transformation was done with the following spatch: @@ identifier p; expression len; expression skb; @@ -p = skb_put(skb, len); -memset(p, 0, len); +p = skb_put_zero(skb, len); Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'mac80211-next-for-davem-2017-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== A couple of weeks worth of updates - looks like things are quiet: * merged net-next back to get a patch from net that another patch here depends on * various small improvements/cleanups across the board * 4-way handshake offload (many thanks to Arend for shepherding that) * mesh CSA/DFS support in mac80211 * the skb_put_zero() we discussed previously ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.open-mesh.org/linux-mergeDavid S. Miller authored
Simon Wunderlich says: ==================== This feature/cleanup patchset includes the following patches: - bump version strings, by Simon Wunderlich - decrease maximum fragment size, by Matthias Schiffer - Clean up seqfile writing, by Markus Elfring (2 patches) - use __func__ in debug messages, by Sven Eckelmann - Mark tpmeter initializers with __init, by Antonio Quartulli - ignore loop detection MAC addresses, by Simon Wunderlich - clean up some return handling, by Simon Wunderlich - improve ELP throughput value handling for WiFi neighbors in BATMAN V/ELP, by Sven Eckelmann (2 patches) ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
yuval.shaia@oracle.com authored
Make return value void since function never return meaningfull value Signed-off-by:
Yuval Shaia <yuval.shaia@oracle.com> Acked-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Sergei Shtylyov says: ==================== MDIO bus reset GPIO cleanups Commit 4c5e7a2c ("dt-bindings: mdio: Clarify binding document") declared that a MDIO reset GPIO property should have only a single GPIO reference/specifier, however the supporting code was left intact... Here's a couple of the obvious cleanups to that code: [1/2] mdio_bus: handle only single PHY reset GPIO [2/2] mdio_bus: use devm_gpiod_get_optional() ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
The MDIO reset GPIO is really a classical optional GPIO property case, so devm_gpiod_get_optional() should have been used, not devm_gpiod_get(). Doing this saves several LoCs... Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
Commit 4c5e7a2c ("dt-bindings: mdio: Clarify binding document") declared that a MDIO reset GPIO property should have only a single GPIO reference/specifier, however the supporting code was left intact, still burdening the kernel with now apparently useless loops -- get rid of them. Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Nathan Fontenot authored
When handling a driver reset due to a failover of the backing server on the vios, doing the netdev_notify_peers() can cause network traffic to stall or halt. Remove the netdev notify call for failover resets. Signed-off-by:
Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Thomas Falcon authored
The IBM vNIC protocol provides support for the user to initiate a failover from the client LPAR in case the current backing infrastructure is deemed inadequate or in an error state. Support for two H_VIOCTL sub-commands for vNIC devices are required to implement this function. These commands are H_GET_SESSION_TOKEN and H_SESSION_ERR_DETECTED. "[H_GET_SESSION_TOKEN] is used to obtain a session token from a VNIC client adapter. This token is opaque to the caller and is intended to be used in tandem with the SESSION_ERROR_DETECTED vioctl subfunction." "[H_SESSION_ERR_DETECTED] is used to report that the currently active backing device for a VNIC client adapter is behaving poorly, and that the hypervisor should attempt to fail over to a different backing device, if one is available." To provide tools access to this functionality the vNIC driver creates a sysfs file that, when written to, will send a request to pHyp to failover to a different backing device. Signed-off-by:
Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Reviewed-by:
Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Antoine Ténart authored
On GOP port 0 two MAC modes are available: GMAC and XLG. The XLG MAC is used for 10G connectivity. This patch adds a basic 10G support by allowing to use the XLG MAC on port 0 and by reworking the port_enable/disable functions so that the XLG MAC is configured when using 10G. Signed-off-by:
Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Vivien Didelot says: ==================== net: dsa: mv88e6xxx: port macros cosmetics This patch series brings no functional changes. It prefixes all common port registers macros with MV88E6XXX_PORT. If registers or some bits differs between switch models, a reference model is chosen (e.g. MV88E6390_PORT_MAC_CTL_SPEED_10000.) The register names are documented as found in the datasheets. Avoid BIT() and shifts defines and prefer a better representation of the Marvell switch registers with ordered, hexadecimal, 16-bit values. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
For implicit namespacing and clarity, prefix the remaining common Port Registers macros with MV88E6XXX_PORT. Document the register and prefer ordered hex masks values for all Marvell 16-bit registers. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
For implicit namespacing and clarity, prefix the common Port IEEE Priority Remapping registers macros with MV88E6095_PORT_IEEE_PRIO. The 88E6390 family turned the 0x18 register into a single indirect table, document that at the same time. Document the register and prefer ordered hex masks values for all Marvell 16-bit registers. Also fix the following checkpatch checks with a temporary variable: CHECK: Alignment should match open parenthesis #65: FILE: drivers/net/dsa/mv88e6xxx/port.c:932: + err = mv88e6xxx_port_ieeepmt_write(chip, port, + MV88E6390_PORT_IEEE_PRIO_MAP_TABLE_INGRESS_PCP, Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
For implicit namespacing and clarity, prefix the common Port Association Vector Register macros with MV88E6XXX_PORT_ASSOC_VECTOR. Document the register and prefer ordered hex masks values for all Marvell 16-bit registers. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
For implicit namespacing and clarity, prefix the common Port Egress Rate Control and Port Egress Rate Control 2 registers macros with MV88E6XXX_PORT_EGRESS_RATE_CTL1 and MV88E6XXX_PORT_EGRESS_RATE_CTL2. Document the register and prefer ordered hex masks values for all Marvell 16-bit registers. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
For implicit namespacing and clarity, prefix the common Port Control 2 Register macros with MV88E6XXX_PORT_CTL2 and the ones which differ between implementations with a chosen reference model (e.g. MV88E6095_PORT_CTL2_CPU_PORT_MASK.) Document the register and prefer ordered hex masks values for all Marvell 16-bit registers. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
For implicit namespacing and clarity, prefix the common Port Default VLAN Register macros with MV88E6XXX_PORT_DEFAULT_VLAN. Document the register and prefer ordered hex masks values for all Marvell 16-bit registers. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
For implicit namespacing and clarity, prefix the common Port Based VLAN Register macros with MV88E6XXX_PORT_BASE_VLAN. Document the register and prefer ordered hex masks values for all Marvell 16-bit registers. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
For implicit namespacing and clarity, prefix the common Port Control 1 Register macros with MV88E6XXX_PORT_CTL1. Document the register and prefer ordered hex masks values for all Marvell 16-bit registers. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
For implicit namespacing and clarity, prefix the common Port Control Register macros with MV88E6XXX_PORT_CTL0 and the ones which differ between implementations with a chosen reference model (e.g. MV88E6185_PORT_CTL0_USE_TAG.) The reason for CTL0 is to make it clear between the badly named "Port Control", "Port Control 1" and "Port Control 2" registers. Document the register and prefer ordered hex masks values for all Marvell 16-bit registers. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
For implicit namespacing and clarity, prefix the common Switch ID Register macros with MV88E6XXX_PORT_SWITCH_ID. Document the register and prefer ordered hex masks values for all Marvell 16-bit registers, this means shifting their values by 4. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
For implicit namespacing and clarity, prefix the common Port Jamming Control Register macros with MV88E6XXX_PORT_JAM_CTL and the ones which differ between implementations with a chosen reference model (e.g. MV88E6097_PORT_JAM_CTL.) The 88E6390 family renamed the register to Flow Control and turned it into an indirect table. Document that as well. Document the register and prefer ordered hex masks values for all Marvell 16-bit registers. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
For implicit namespacing and clarity, prefix the common MAC Control Register macros with MV88E6XXX_PORT_MAC_CTL and the ones which differ between implementations with a chosen reference model (e.g. MV88E6065_PORT_MAC_CTL_SPEED_200.) Document the register and prefer ordered hex masks values for all Marvell 16-bit registers. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vivien Didelot authored
For implicit namespacing and clarity, prefix the common Port Status Register macros with MV88E6XXX_PORT_STS and the ones which differ between implementations with a chosen reference model (e.g. MV88E6352_PORT_STS_EEE.) Document the register and prefer ordered hex masks values for all Marvell 16-bit registers. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Sven Eckelmann authored
The wifi driver can decide to not provide parts of the station info. For example, the expected throughput of the station can be omitted when the used rate control doesn't provide this kind of information. The B.A.T.M.A.N. V implementation must therefore check the filled bitfield before it tries to access the expected_throughput of the returned station_info. Reported-by:
Alvaro Antelo <alvaro.antelo@gmail.com> Fixes: c833484e ("batman-adv: ELP - compute the metric based on the estimated throughput") Signed-off-by:
Sven Eckelmann <sven@narfation.org> Reviewed-by:
Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by:
Simon Wunderlich <sw@simonwunderlich.de>
-
Sven Eckelmann authored
A wifi interface should never be handled like an ethernet devices. The parser of the cfg80211 output must therefore skip the ethtool code when cfg80211_get_station returned an error. Fixes: f44a3ae9 ("batman-adv: refactor wifi interface detection") Signed-off-by:
Sven Eckelmann <sven@narfation.org> Reviewed-by:
Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by:
Simon Wunderlich <sw@simonwunderlich.de>
-
Andy Shevchenko authored
Switch to use managed variant of acpi_dev_add_driver_gpios() to simplify error path and fix potentially wrong assingment if ->probe() fails. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Emmanuel Grumbach authored
It is very useful to know what ampdu action is currently happening. Add this information to the tracepoint. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Arend Van Spriel authored
The description of NL80211_CMD_ROAM indicated possibility for a request to roam issued by user-space. However, it also states that as not being implemented right now. This has been so since commit b23aa676 ("cfg80211: connect/disconnect API") added in 2009. So it seems safe to assume it will not be added any time soon and thus remove it. Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Avraham Stern authored
Drivers that initiate roaming while being connected to a network that uses 802.1X authentication need to inform user space if 802.1X authentication is further required after roaming. For example, when using the Fast transition protocol, roaming within the mobility domain does not require new 802.1X authentication, but roaming to another mobility domain does. In addition, some drivers may not support 802.1X authentication (so it has to be done in user space), while other drivers do. Add a flag to the roaming notification to indicate if user space is required to do 802.1X authentication after the roaming or not. This flag will only be used for networks that use 802.1X authentication. For networks that do not use 802.1X authentication it is assumed that no further action is required from user space after the roaming notification. Signed-off-by:
Avraham Stern <avraham.stern@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> [arend.vanspriel@broadcom.com reuse NL80211_ATTR_PORT_AUTHORIZED] Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> [rebase to apply w/o the flag in CONNECT] Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Avraham Stern authored
Add API for setting the PMK to the driver. For FT support, allow setting also the PMK-R0 Name. This can be used by drivers that support 4-Way handshake offload while IEEE802.1X authentication is managed by upper layers. Signed-off-by:
Avraham Stern <avraham.stern@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> [arend.vanspriel@broadcom.com: add WANT_1X_4WAY_HS attribute] Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> [reword NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_1X docs a bit to say that the device may require it] Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Eliad Peller authored
Let drivers advertise support for station-mode 4-way handshake offloading with a new NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK flag. Extend use of NL80211_ATTR_PMK attribute indicating it might be passed as part of NL80211_CMD_CONNECT command, and contain the PSK (which is the PMK, hence the name.) The driver/device is assumed to handle the 4-way handshake by itself in this case (including key derivations, etc.), instead of relying on the supplicant. This patch is somewhat based on this one (by Vladimir Kondratiev): https://patchwork.kernel.org/patch/1309561/. Signed-off-by:
Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by:
Eliad Peller <eliadx.peller@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> [arend.vanspriel@broadcom.com rebase dealing with existing ATTR_PMK] Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> [reword NL80211_EXT_FEATURE_4WAY_HANDSHAKE_STA_PSK docs to indicate that this offload might be required] Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-