- 14 May, 2014 1 commit
-
-
Geert Uytterhoeven authored
Caused by interaction between commit 08ec67b5 ("ARM: shmobile: r8a7740 dtsi: Add Ethernet support") and commit 9ff254ad ("ARM: shmobile: dts: Move interrupt-parent property to root node"). Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Simon Horman <horms+renesas@verge.net.au>
-
- 13 May, 2014 4 commits
-
-
Simon Horman authored
This change makes the DTS consistent with the platform data that exists in board-marzen.c. Empirically it does not appear to be necessary. Signed-off-by: -
Geert Uytterhoeven authored
Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Laurent Pinchart authored
There's no need to duplicate the interrupt-parent property in all DT nodes as the kernel automatically walks parent nodes to find the property. Specify it once in the root node only. Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
-
- 11 May, 2014 5 commits
-
-
Geert Uytterhoeven authored
Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Sergei Shtylyov authored
Define the Henninger board dependent part of the MSIOF0 device node. Add device node for Renesas R2A11302FT PMIC for which no bindings exist yet. Based on the Koelsch MSIOF device tree patch by Geert Uytterhoeven. Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
Sergei Shtylyov authored
Define the Henninger board dependent part of the QSPI device node. Add device nodes for Spansion S25FL512S SPI flash and MTD partitions on it. Signed-off-by:
-
Sergei Shtylyov authored
Define the Henninger board dependent part of the SDHI0/2 device nodes along with the necessary voltage regulators (note that the Vcc regulators are dummy -- they are required but don't actually exist on the board). Also, GPIOs have to be used for the CD and WP signals due to the SDHI driver constraints... Signed-off-by:
-
- 02 May, 2014 1 commit
-
-
Sergei Shtylyov authored
When creating the initial device tree for the Henninger board, I've overlooked that EXTAL frequency needs to be overridden there. The 'sh-sci' driver managed to work somehow but the SDHI driver that I've tried to enable just hanged with the default EXTAL frequency of 0... Signed-off-by:
-
- 28 Apr, 2014 1 commit
-
-
Sergei Shtylyov authored
Enable SATA0 device for the Henninger board. Signed-off-by:
-
- 25 Apr, 2014 2 commits
-
-
Sergei Shtylyov authored
Define the Henninger board dependent part of the Ether device node. Enable DHCP and NFS root for the kernel booting. Signed-off-by:
-
Sergei Shtylyov authored
Add the initial device tree for the R8A7791 SoC based Henninger board. SCIF0 serial port support is included, so that the serial console can work. Signed-off-by:
-
- 16 Apr, 2014 1 commit
-
-
Geert Uytterhoeven authored
Use "sii,s35390a" instead of "seiko,s35390a", cfr. Documentation/devicetree/bindings/i2c/trivial-devices.txt and Documentation/devicetree/bindings/vendor-prefixes.txt. Signed-off-by:
Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by:
-
- 14 Apr, 2014 25 commits
-
-
Geert Uytterhoeven authored
Signed-off-by:
Magnus Damm <damm@opensource.se> Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
Wolfram Sang <wsa@sang-engineering.com> Acked-by:
-
Wolfram Sang authored
Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Laurent Pinchart authored
All I2C clocks derive from the HP clock, not from the P clock. Fix them. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by:
-
Laurent Pinchart authored
All I2C clocks derive from the HP clock, not from the P clock. Fix them. Signed-off-by:
-
Simon Horman authored
The correct binding is "micrel,led-mode", not "led-mode". This corrects an error which was introduced when setting of ethernet PHY LED mode was added by 82e62182d59bd1d0 ("ARM: shmobile: lager: Set ethernet PHY LED mode"). This makes the lager code consistent with the koelsch code which was added by ae00d12a032490b3 ("ARM: shmobile: koelsch: Set ethernet PHY LED mode"). Acked-by: -
Ulrich Hecht authored
This enables the Seiko real-time clock that is attached to a couple of GPIO pins. Signed-off-by:
Ulrich Hecht <ulrich.hecht@gmail.com> Signed-off-by:
-
Magnus Damm authored
Add support for EHCI clock gating via the MSTP703 bit on r8a7791. Signed-off-by:
-
Ulrich Hecht authored
Add "renesas,*-r8a7740" to the compatible strings for consistency with other devices. Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Wolfram Sang authored
This node should have a unique name so it can be distinguished when other i2c busses are added later. Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Wolfram Sang authored
Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
Geert Uytterhoeven <geert+renesas@linux-m68k.org> Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Laurent Pinchart authored
The Koelsch board uses the ethernet PHY LED0 as a link signal connected to the ethernet controller. Specify the corresponding LED mode for the PHY. Signed-off-by:
-
Laurent Pinchart authored
The Lager board uses the ethernet PHY LED0 as a link signal connected to the ethernet controller. Specify the corresponding LED mode for the PHY. Signed-off-by:
-
Magnus Damm authored
Add DTS gpio-keys support for SW2 on the Koelsch board. This makes the DT code match the legacy board code. Also update the existing gpio-keys nodes to make use of KEY_n. Signed-off-by:
-
Magnus Damm authored
Add DTS gpio-keys support for SW2 on the Lager board. This makes the DT code match the legacy board code. Signed-off-by:
-
Geert Uytterhoeven authored
Add Spansion s25fl008k SPI FLASH and MTD partition, based on bockw legacy board code. Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by:
-
Geert Uytterhoeven authored
- Add "renesas,hspi-r8a7779" compatible value, - Correct reference to parent interrupt controller (use "interrupt-parent" instead of "interrupt-controller"), - Add missing "#address-cells" and "#size-cells" properties, which are needed when populating the SPI buses. Signed-off-by: -
Geert Uytterhoeven authored
- Add "renesas,hspi-r8a7778" compatible value, - Correct reference to parent interrupt controller (use "interrupt-parent" instead of "interrupt-controller"), - Add missing "#address-cells" and "#size-cells" properties, which are needed when populating the SPI buses. Signed-off-by:
-
