All atomic state should be cleared when drm_modeset_backoff() is
called, because it drops all locks and the state becomes invalid.

The call to drm_atomic_state_clear was missing in atomic_remove_fb,
so add the missing call there.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170629115954.26029-1-maarten.lankhorst@linux.intel.comReviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: db8f6403 ("drm: Convert drm_framebuffer_remove to atomic, v4.")
Cc: stable@vger.kernel.org # v4.12-rc1+

Commit 3fcdcb27 ("drm/vblank: Switch to bool in_vblank_irq in
get_vblank_timestamp") inverted a condition by mistake that resulted in
vblank timestamps always being 0 on hardware without a vblank counter.
Fix it.

Fixes: 3fcdcb27 ("drm/vblank: Switch to bool in_vblank_irq in get_vblank_timestamp")
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170629123720.27173-1-laurent.pinchart+renesas@ideasonboard.com

Backmerge drm-next with rc7

Linux 4.12-rc7

Needed at least rc6 for drm-misc-next-fixes, may as well go to rc7

The "supported input formats" table in dw_hdmi.h was incorrectly formatted,
using "+" signs where "|" needs to be.  That, in turn, causes the PDF build
to fail.

Fixes: def23aa7 ("drm: bridge: dw-hdmi: Switch to V4L bus format and encodings")
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170623140013.0703107a@lwn.net

Pull x86 fix from Thomas Gleixner:
 "A single fix to unbreak the vdso32 build for 64bit kernels caused by
  excess #includes in the mshyperv header"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mshyperv: Remove excess #includes from mshyperv.h

Pull timer fixes from Thomas Gleixner:
 "A few fixes for timekeeping and timers:

   - Plug a subtle race due to a missing READ_ONCE() in the timekeeping
     code where reloading of a pointer results in an inconsistent
     callback argument being supplied to the clocksource->read function.

   - Correct the CLOCK_MONOTONIC_RAW sub-nanosecond accounting in the
     time keeping core code, to prevent a possible discontuity.

   - Apply a similar fix to the arm64 vdso clock_gettime()
     implementation

   - Add missing includes to clocksource drivers, which relied on
     indirect includes which fails in certain configs.

   - Use the proper iomem pointer for read/iounmap in a probe function"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  arm64/vdso: Fix nsec handling for CLOCK_MONOTONIC_RAW
  time: Fix CLOCK_MONOTONIC_RAW sub-nanosecond accounting
  time: Fix clock->read(clock) race around clocksource changes
  clocksource: Explicitly include linux/clocksource.h when needed
  clocksource/drivers/arm_arch_timer: Fix read and iounmap of incorrect variable

Pull perf fixes from Thomas Gleixner:
 "Three fixlets for perf:

   - Return the proper error code if aux buffers for a event are not
     supported.

   - Calculate the probe offset for inlined functions correctly

   - Update the Skylake DTLB load/store miss event so it can count 1G
     TLB entries as well"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf probe: Fix probe definition for inlined functions
  perf/x86/intel: Add 1G DTLB load/store miss support for SKL
  perf/aux: Correct return code of rb_alloc_aux() if !has_aux(ev)

Pull irq fix from Thomas Gleixner:
 "A single fix for the MIPS GIC to prevent ftrace recursion"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/mips-gic: Mark count and compare accessors notrace

Pull input fixes from Dmitry Torokhov:

 - a quirk to i8042 to ignore timeout bit on Lifebook AH544

 - a fixup to Synaptics RMI function 54 that was breaking some Dells

 - a fix for memory leak in soc_button_array driver

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics-rmi4 - only read the F54 query registers which are used
  Input: i8042 - add Fujitsu Lifebook AH544 to notimeout list
  Input: soc_button_array - fix leaking the ACPI button descriptor buffer

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are the target-pending fixes for v4.12-rc7 that have been queued
  up for the last 2 weeks. This includes:

   - Fix a TMR related kref underflow detected by the recent refcount_t
     conversion in upstream.

   - Fix a iscsi-target corner case during explicit connection logout
     timeout failure.

   - Address last fallout in iscsi-target immediate data handling from
     v4.4 target-core now allowing control CDB payload underflow"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target: Reject immediate data underflow larger than SCSI transfer length
  iscsi-target: Fix delayed logout processing greater than SECONDS_FOR_LOGOUT_COMP
  target: Fix kref->refcount underflow in transport_cmd_finish_abort

Merge tag 'kbuild-fixes-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:
 "Nothing scary, just some random fixes:

   - fix warnings of host programs

   - fix "make tags" when COMPILED_SOURCE=1 is specified along with O=

   - clarify help message of C=1 option

   - fix dependency for ncurses compatibility check

   - fix "make headers_install" for fakechroot environment"

* tag 'kbuild-fixes-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: fix sparse warnings in nconfig
  kbuild: fix header installation under fakechroot environment
  kconfig: Check for libncurses before menuconfig
  Kbuild: tiny correction on `make help`
  tags: honor COMPILED_SOURCE with apart output directory
  genksyms: add printf format attribute to error_with_pos()

Pull timer fix from Eric Biederman:
 "This fixes an issue of confusing injected signals with the signals
  from posix timers that has existed since posix timers have been in the
  kernel.

  This patch is slightly simpler than my earlier version of this patch
  as I discovered in testing that I had misspelled "#ifdef
  CONFIG_POSIX_TIMERS". So I deleted that unnecessary test and made
  setting of resched_timer uncondtional.

  I have tested this and verified that without this patch there is a
  nasty hang that is easy to trigger, and with this patch everything
  works properly"

Thomas Gleixner dixit:
 "It fixes the problem at hand and covers the ptrace case as well, which
  I missed.

  Reviewed-and-tested-by: Thomas Gleixner <tglx@linutronix.de>"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  signal: Only reschedule timers on signals timers have sent

A recent commit included linux/slab.h in linux/irq.h. This breaks the build
of vdso32 on a 64-bit kernel.

The reason is that linux/irq.h gets included into the vdso code via
linux/interrupt.h which is included from asm/mshyperv.h. That makes the
32-bit vdso compile fail, because slab.h includes the pgtable headers for
64-bit on a 64-bit build.

Neither linux/clocksource.h nor linux/interrupt.h are needed in the
mshyperv.h header file itself - it has a dependency on <linux/atomic.h>.

Remove the includes and unbreak the build.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: devel@linuxdriverproject.org
Fixes: dee863b5 ("hv: export current Hyper-V clocksource")
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1706231038460.2647@nanosSigned-off-by: Ingo Molnar <mingo@kernel.org>

Pull powerpc fixes from Michael Ellerman:
 "Some more powerpc fixes for 4.12. Most of these actually came in last
  week but got held up for some more testing.

   - three fixes for kprobes/ftrace/livepatch interactions.

   - properly handle data breakpoints when using the Radix MMU.

   - fix for perf sampling of registers during call_usermodehelper().

   - properly initialise the thread_info on our emergency stacks

   - add an explicit flush when doing TLB invalidations for a process
     using NPU2.

  Thanks to: Alistair Popple, Naveen N. Rao, Nicholas Piggin, Ravi
  Bangoria, Masami Hiramatsu"

* tag 'powerpc-4.12-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64: Initialise thread_info for emergency stacks
  powerpc/powernv/npu-dma: Add explicit flush when sending an ATSD
  powerpc/perf: Fix oops when kthread execs user process
  powerpc/64s: Handle data breakpoints in Radix mode
  powerpc/kprobes: Skip livepatch_handler() for jprobes
  powerpc/ftrace: Pass the correct stack pointer for DYNAMIC_FTRACE_WITH_REGS
  powerpc/kprobes: Pause function_graph tracing during jprobes handling

Pull ACPI fix from Rafael Wysocki:
 "This fixes the ACPI-based enumeration of some I2C and SPI devices
  broken in 4.11.

  Specifics:

   - I2C and SPI devices are expected to be enumerated by the I2C and
     SPI subsystems, respectively, but due to a change made during the
     4.11 cycle, in some cases the ACPI core marks them as already
     enumerated which causes the I2C and SPI subsystems to overlook
     them, so fix that (Jarkko Nikula)"

* tag 'acpi-4.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / scan: Fix enumeration for special SPI and I2C devices

Pull i2c fix from Wolfram Sang.

* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: imx: Use correct function to write to register

Pull GPIO fix from Linus Walleij:
 "A single GPIO patch fixing the compatible string for the MVEBU PWM
  controller embedded in the GPIO controller before we release v4.12.
  Hopefully"

* tag 'gpio-v4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: mvebu: change compatible string for PWM support

Pull sound fixes from Takashi Iwai:
 "Nothing exciting here, just a few stable fixes:

   - suppress spurious kernel WARNING in PCM core

   - fix potential spin deadlock at error handling in firewire

   - HD-audio PCI ID addition / fixup"

* tag 'sound-4.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Apply quirks to Broxton-T, too
  ALSA: firewire-lib: Fix stall of process context at packet error
  ALSA: pcm: Don't treat NULL chmap as a fatal error
  ALSA: hda - Add Coffelake PCI ID

Pull drm fixes from Dave Airlie:
 "A varied bunch of fixes, one for an API regression with connectors.

  Otherwise amdgpu and i915 have a bunch of varied fixes, the shrinker
  ones being the most important"

* tag 'drm-fixes-for-v4.12-rc7' of git://people.freedesktop.org/~airlied/linux:
  drm: Fix GETCONNECTOR regression
  drm/radeon: add a quirk for Toshiba Satellite L20-183
  drm/radeon: add a PX quirk for another K53TK variant
  drm/amdgpu: adjust default display clock
  drm/amdgpu/atom: fix ps allocation size for EnableDispPowerGating
  drm/amdgpu: add Polaris12 DID
  drm/i915: Don't enable backlight at setup time.
  drm/i915: Plumb the correct acquire ctx into intel_crtc_disable_noatomic()
  drm/i915: Fix deadlock witha the pipe A quirk during resume
  drm/i915: Remove __GFP_NORETRY from our buffer allocator
  drm/i915: Encourage our shrinker more when our shmemfs allocations fails
  drm/i915: Differentiate between sw write location into ring and last hw read

Pull random fixes from Ted Ts'o:
 "Fix some locking and gcc optimization issues from the most recent
  random_for_linus_stable pull request"

* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: silence compiler warnings and fix race

Merge tag 'for-4.12/dm-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - a revert of a DM mirror commit that has proven to make the code prone
   to crash

 - a DM io reference count fix that resolves a NULL pointer seen when
   issuing discards to a DM mirror target's device whose mirror legs do
   not all support discards

 - a couple DM integrity fixes

* tag 'for-4.12/dm-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm io: fix duplicate bio completion due to missing ref count
  dm integrity: fix to not disable/enable interrupts from interrupt context
  Revert "dm mirror: use all available legs on multiple failures"
  dm integrity: reject mappings too large for device

Merge misc fixes from Andrew Morton:
 "8 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  fs/exec.c: account for argv/envp pointers
  ocfs2: fix deadlock caused by recursive locking in xattr
  slub: make sysfs file removal asynchronous
  lib/cmdline.c: fix get_options() overflow while parsing ranges
  fs/dax.c: fix inefficiency in dax_writeback_mapping_range()
  autofs: sanity check status reported with AUTOFS_DEV_IOCTL_FAIL
  mm/vmalloc.c: huge-vmap: fail gracefully on unexpected huge vmap mappings
  mm, thp: remove cond_resched from __collapse_huge_page_copy

When limiting the argv/envp strings during exec to 1/4 of the stack limit,
the storage of the pointers to the strings was not included.  This means
that an exec with huge numbers of tiny strings could eat 1/4 of the stack
limit in strings and then additional space would be later used by the
pointers to the strings.

For example, on 32-bit with a 8MB stack rlimit, an exec with 1677721
single-byte strings would consume less than 2MB of stack, the max (8MB /
4) amount allowed, but the pointers to the strings would consume the
remaining additional stack space (1677721 * 4 == 6710884).

The result (1677721 + 6710884 == 8388605) would exhaust stack space
entirely.  Controlling this stack exhaustion could result in
pathological behavior in setuid binaries (CVE-2017-1000365).

[akpm@linux-foundation.org: additional commenting from Kees]
Fixes: b6a2fea3 ("mm: variable length argument support")
Link: http://lkml.kernel.org/r/20170622001720.GA32173@beastSigned-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Qualys Security Advisory <qsa@qualys.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Another deadlock path caused by recursive locking is reported.  This
kind of issue was introduced since commit 743b5f14 ("ocfs2: take
inode lock in ocfs2_iop_set/get_acl()").  Two deadlock paths have been
fixed by commit b891fa50 ("ocfs2: fix deadlock issue when taking
inode lock at vfs entry points").  Yes, we intend to fix this kind of
case in incremental way, because it's hard to find out all possible
paths at once.

This one can be reproduced like this.  On node1, cp a large file from
home directory to ocfs2 mountpoint.  While on node2, run
setfacl/getfacl.  Both nodes will hang up there.  The backtraces:

On node1:
  __ocfs2_cluster_lock.isra.39+0x357/0x740 [ocfs2]
  ocfs2_inode_lock_full_nested+0x17d/0x840 [ocfs2]
  ocfs2_write_begin+0x43/0x1a0 [ocfs2]
  generic_perform_write+0xa9/0x180
  __generic_file_write_iter+0x1aa/0x1d0
  ocfs2_file_write_iter+0x4f4/0xb40 [ocfs2]
  __vfs_write+0xc3/0x130
  vfs_write+0xb1/0x1a0
  SyS_write+0x46/0xa0

On node2:
  __ocfs2_cluster_lock.isra.39+0x357/0x740 [ocfs2]
  ocfs2_inode_lock_full_nested+0x17d/0x840 [ocfs2]
  ocfs2_xattr_set+0x12e/0xe80 [ocfs2]
  ocfs2_set_acl+0x22d/0x260 [ocfs2]
  ocfs2_iop_set_acl+0x65/0xb0 [ocfs2]
  set_posix_acl+0x75/0xb0
  posix_acl_xattr_set+0x49/0xa0
  __vfs_setxattr+0x69/0x80
  __vfs_setxattr_noperm+0x72/0x1a0
  vfs_setxattr+0xa7/0xb0
  setxattr+0x12d/0x190
  path_setxattr+0x9f/0xb0
  SyS_setxattr+0x14/0x20

Fix this one by using ocfs2_inode_{lock|unlock}_tracker, which is
exported by commit 439a36b8 ("ocfs2/dlmglue: prepare tracking logic
to avoid recursive cluster lock").

Link: http://lkml.kernel.org/r/20170622014746.5815-1-zren@suse.com
Fixes: 743b5f14 ("ocfs2: take inode lock in ocfs2_iop_set/get_acl()")
Signed-off-by: Eric Ren <zren@suse.com>
Reported-by: Thomas Voegtle <tv@lio96.de>
Tested-by: Thomas Voegtle <tv@lio96.de>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Mark Fasheh <mfasheh@versity.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit bf5eb3de ("slub: separate out sysfs_slab_release() from
sysfs_slab_remove()") made slub sysfs file removals synchronous to
kmem_cache shutdown.

Unfortunately, this created a possible ABBA deadlock between slab_mutex
and sysfs draining mechanism triggering the following lockdep warning.

  ======================================================
  [ INFO: possible circular locking dependency detected ]
  4.10.0-test+ #48 Not tainted
  -------------------------------------------------------
  rmmod/1211 is trying to acquire lock:
   (s_active#120){++++.+}, at: [<ffffffff81308073>] kernfs_remove+0x23/0x40

  but task is already holding lock:
   (slab_mutex){+.+.+.}, at: [<ffffffff8120f691>] kmem_cache_destroy+0x41/0x2d0

  which lock already depends on the new lock.

  the existing dependency chain (in reverse order) is:

  -> #1 (slab_mutex){+.+.+.}:
	 lock_acquire+0xf6/0x1f0
	 __mutex_lock+0x75/0x950
	 mutex_lock_nested+0x1b/0x20
	 slab_attr_store+0x75/0xd0
	 sysfs_kf_write+0x45/0x60
	 kernfs_fop_write+0x13c/0x1c0
	 __vfs_write+0x28/0x120
	 vfs_write+0xc8/0x1e0
	 SyS_write+0x49/0xa0
	 entry_SYSCALL_64_fastpath+0x1f/0xc2

  -> #0 (s_active#120){++++.+}:
	 __lock_acquire+0x10ed/0x1260
	 lock_acquire+0xf6/0x1f0
	 __kernfs_remove+0x254/0x320
	 kernfs_remove+0x23/0x40
	 sysfs_remove_dir+0x51/0x80
	 kobject_del+0x18/0x50
	 __kmem_cache_shutdown+0x3e6/0x460
	 kmem_cache_destroy+0x1fb/0x2d0
	 kvm_exit+0x2d/0x80 [kvm]
	 vmx_exit+0x19/0xa1b [kvm_intel]
	 SyS_delete_module+0x198/0x1f0
	 entry_SYSCALL_64_fastpath+0x1f/0xc2

  other info that might help us debug this:

   Possible unsafe locking scenario:

	 CPU0                    CPU1
	 ----                    ----
    lock(slab_mutex);
				 lock(s_active#120);
				 lock(slab_mutex);
    lock(s_active#120);

   *** DEADLOCK ***

  2 locks held by rmmod/1211:
   #0:  (cpu_hotplug.dep_map){++++++}, at: [<ffffffff810a7877>] get_online_cpus+0x37/0x80
   #1:  (slab_mutex){+.+.+.}, at: [<ffffffff8120f691>] kmem_cache_destroy+0x41/0x2d0

  stack backtrace:
  CPU: 3 PID: 1211 Comm: rmmod Not tainted 4.10.0-test+ #48
  Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v02.05 05/07/2012
  Call Trace:
   print_circular_bug+0x1be/0x210
   __lock_acquire+0x10ed/0x1260
   lock_acquire+0xf6/0x1f0
   __kernfs_remove+0x254/0x320
   kernfs_remove+0x23/0x40
   sysfs_remove_dir+0x51/0x80
   kobject_del+0x18/0x50
   __kmem_cache_shutdown+0x3e6/0x460
   kmem_cache_destroy+0x1fb/0x2d0
   kvm_exit+0x2d/0x80 [kvm]
   vmx_exit+0x19/0xa1b [kvm_intel]
   SyS_delete_module+0x198/0x1f0
   ? SyS_delete_module+0x5/0x1f0
   entry_SYSCALL_64_fastpath+0x1f/0xc2

It'd be the cleanest to deal with the issue by removing sysfs files
without holding slab_mutex before the rest of shutdown; however, given
the current code structure, it is pretty difficult to do so.

This patch punts sysfs file removal to a work item.  Before commit
bf5eb3de, the removal was punted to a RCU delayed work item which is
executed after release.  Now, we're punting to a different work item on
shutdown which still maintains the goal removing the sysfs files earlier
when destroying kmem_caches.

Link: http://lkml.kernel.org/r/20170620204512.GI21326@htj.duckdns.org
Fixes: bf5eb3de ("slub: separate out sysfs_slab_release() from sysfs_slab_remove()")
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When using get_options() it's possible to specify a range of numbers,
like 1-100500.  The problem is that it doesn't track array size while
calling internally to get_range() which iterates over the range and
fills the memory with numbers.

Link: http://lkml.kernel.org/r/2613C75C-B04D-4BFF-82A6-12F97BA0F620@gmail.comSigned-off-by: Ilya V. Matveychikov <matvejchikov@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

dax_writeback_mapping_range() fails to update iteration index when
searching radix tree for entries needing cache flushing.  Thus each
pagevec worth of entries is searched starting from the start which is
inefficient and prone to livelocks.  Update index properly.

Link: http://lkml.kernel.org/r/20170619124531.21491-1-jack@suse.cz
Fixes: 9973c98e ("dax: add support for fsync/sync")
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If a positive status is passed with the AUTOFS_DEV_IOCTL_FAIL ioctl,
autofs4_d_automount() will return

   ERR_PTR(status)

with that status to follow_automount(), which will then dereference an
invalid pointer.

So treat a positive status the same as zero, and map to ENOENT.

See comment in systemd src/core/automount.c::automount_send_ready().

Link: http://lkml.kernel.org/r/871sqwczx5.fsf@notabene.neil.brown.nameSigned-off-by: NeilBrown <neilb@suse.com>
Cc: Ian Kent <raven@themaw.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Existing code that uses vmalloc_to_page() may assume that any address
for which is_vmalloc_addr() returns true may be passed into
vmalloc_to_page() to retrieve the associated struct page.

This is not un unreasonable assumption to make, but on architectures
that have CONFIG_HAVE_ARCH_HUGE_VMAP=y, it no longer holds, and we need
to ensure that vmalloc_to_page() does not go off into the weeds trying
to dereference huge PUDs or PMDs as table entries.

Given that vmalloc() and vmap() themselves never create huge mappings or
deal with compound pages at all, there is no correct answer in this
case, so return NULL instead, and issue a warning.

When reading /proc/kcore on arm64, you will hit an oops as soon as you
hit the huge mappings used for the various segments that make up the
mapping of vmlinux.  With this patch applied, you will no longer hit the
oops, but the kcore contents willl be incorrect (these regions will be
zeroed out)

We are fixing this for kcore specifically, so it avoids vread() for
those regions.  At least one other problematic user exists, i.e.,
/dev/kmem, but that is currently broken on arm64 for other reasons.

Link: http://lkml.kernel.org/r/20170609082226.26152-1-ard.biesheuvel@linaro.orgSigned-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is a partial revert of commit 338a16ba ("mm, thp: copying user
pages must schedule on collapse") which added a cond_resched() to
__collapse_huge_page_copy().

On x86 with CONFIG_HIGHPTE, __collapse_huge_page_copy is called in
atomic context and thus scheduling is not possible.  This is only a
possible config on arm and i386.

Although need_resched has been shown to be set for over 100 jiffies
while doing the iteration in __collapse_huge_page_copy, this is better
than doing

	if (in_atomic())
		cond_resched()

to cover only non-CONFIG_HIGHPTE configs.

Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1706191341550.97821@chino.kir.corp.google.comSigned-off-by: David Rientjes <rientjes@google.com>
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull SCSI fixes from James Bottomley:
 "Two fixes to remove spurious WARN_ONs from the new(ish) qedi driver.

  The driver already prints a warning message, there's no need to panic
  users by printing something that looks like an oops as well"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: qedi: Remove WARN_ON from clear task context.
  scsi: qedi: Remove WARN_ON for untracked cleanup.

Pull xfs fixes from Darrick Wong:
 "I have one more bugfix for you for 4.12-rc7 to fix a disk corruption
  problem:

   - don't allow swapon on files on the realtime device, because the
     swap code will swap pages out to blocks on the data device, thereby
     corrupting the filesystem"

* tag 'xfs-4.12-fixes-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: don't allow bmap on rt files

Merge tag 'perf-urgent-for-mingo-4.12-20170622' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

Pull 'perf probe' fix from Arnaldo Carvalho de Melo:

 - Do not double the offset of inline expansions when using
   'perf probe' on inlined functions (Björn Töpel)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>

The F54 driver is currently only using the first 6 bytes of F54 so there is
no need to read all 27 bytes. Some Dell systems (Dell XP13 9333 and
similar) have an issue with the touchpad or I2C bus when reading reports
larger then 16 bytes. Reads larger then 16 bytes are reported in two HID
reports. Something about the back to back reports seems to cause the next
read to report incorrect data. This results in F30 failing to load and the
click button failing to work.

Previous issues with the I2C controller or touchpad were addressed in:
commit 5b65c2a0 ("HID: rmi: check sanity of the incoming report")

Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=195949Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

hdlcd fixes.

* tag 'hdlcd-for-v4.13-v3' of git://linux-arm.org/linux-ld:
  drm/arm: hdlcd: remove unused variables
  drm/arm: hdlcd: Use CMA helper for plane buffer address calculation
  drm/arm: hdlcd: Set the CRTC's port before binding the encoder.

Emergency stacks have their thread_info mostly uninitialised, which in
particular means garbage preempt_count values.

Emergency stack code runs with interrupts disabled entirely, and is
used very rarely, so this has been unnoticed so far. It was found by a
proposed new powerpc watchdog that takes a soft-NMI directly from the
masked_interrupt handler and using the emergency stack. That crashed
at BUG_ON(in_nmi()) in nmi_enter(). preempt_count()s were found to be
garbage.

To fix this, zero the entire THREAD_SIZE allocation, and initialize
the thread_info.

Cc: stable@vger.kernel.org
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Move it all into setup_64.c, use a function not a macro. Fix
      crashes on Cell by setting preempt_count to 0 not HARDIRQ_OFFSET]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

UAPI Changes:
- drm: Fix regression in GETCONNECTOR ioctl returning stale properties (Daniel)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>

* tag 'drm-misc-fixes-2017-06-22' of git://anongit.freedesktop.org/git/drm-misc:
  drm: Fix GETCONNECTOR regression

Fix sparse warnings in scripts/kconfig/nconf* ('make nconfig'):

../scripts/kconfig/nconf.c:1071:32: warning: Using plain integer as NULL pointer
../scripts/kconfig/nconf.c:1238:30: warning: Using plain integer as NULL pointer
../scripts/kconfig/nconf.c:511:51: warning: Using plain integer as NULL pointer
../scripts/kconfig/nconf.c:1460:6: warning: symbol 'setup_windows' was not declared. Should it be static?
../scripts/kconfig/nconf.c:274:12: warning: symbol 'current_instructions' was not declared. Should it be static?
../scripts/kconfig/nconf.c:308:22: warning: symbol 'function_keys' was not declared. Should it be static?
../scripts/kconfig/nconf.gui.c:132:17: warning: non-ANSI function declaration of function 'set_colors'
../scripts/kconfig/nconf.gui.c:195:24: warning: Using plain integer as NULL pointer

nconf.gui.o before/after files are the same.
nconf.o before/after files are the same until the 'static' function
declarations are added.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>