The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.

When memory is allocated in 'ql_alloc_net_req_rsp_queues()' GFP_KERNEL can
be used because it is only called from 'ql_alloc_mem_resources()' which
already calls 'ql_alloc_buffer_queues()' which uses GFP_KERNEL. (see below)

When memory is allocated in 'ql_alloc_buffer_queues()' GFP_KERNEL can be
used because this flag is already used just a few line above.

When memory is allocated in 'ql_alloc_small_buffers()' GFP_KERNEL can
be used because it is only called from 'ql_alloc_mem_resources()' which
already calls 'ql_alloc_buffer_queues()' which uses GFP_KERNEL. (see above)

When memory is allocated in 'ql_alloc_mem_resources()' GFP_KERNEL can be
used because this function already calls 'ql_alloc_buffer_queues()' which
uses GFP_KERNEL. (see above)

While at it, use 'dma_set_mask_and_coherent()' instead of 'dma_set_mask()/
dma_set_coherent_mask()' in order to slightly simplify code.

@@
@@
-    PCI_DMA_BIDIRECTIONAL
+    DMA_BIDIRECTIONAL

@@
@@
-    PCI_DMA_TODEVICE
+    DMA_TO_DEVICE

@@
@@
-    PCI_DMA_FROMDEVICE
+    DMA_FROM_DEVICE

@@
@@
-    PCI_DMA_NONE
+    DMA_NONE

@@
expression e1, e2, e3;
@@
-    pci_alloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
-    pci_zalloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
-    pci_free_consistent(e1, e2, e3, e4)
+    dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_single(e1, e2, e3, e4)
+    dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_single(e1, e2, e3, e4)
+    dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
-    pci_map_page(e1, e2, e3, e4, e5)
+    dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_page(e1, e2, e3, e4)
+    dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_sg(e1, e2, e3, e4)
+    dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_sg(e1, e2, e3, e4)
+    dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+    dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_device(e1, e2, e3, e4)
+    dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+    dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+    dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
-    pci_dma_mapping_error(e1, e2)
+    dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_dma_mask(e1, e2)
+    dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_consistent_dma_mask(e1, e2)
+    dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20210117081542.560021-1-christophe.jaillet@wanadoo.frSigned-off-by: Jakub Kicinski <kuba@kernel.org>

tcf_action_init_1() loads tc action modules automatically with
request_module() after parsing the tc action names, and it drops RTNL
lock and re-holds it before and after request_module(). This causes a
lot of troubles, as discovered by syzbot, because we can be in the
middle of batch initializations when we create an array of tc actions.

One of the problem is deadlock:

CPU 0					CPU 1
rtnl_lock();
for (...) {
  tcf_action_init_1();
    -> rtnl_unlock();
    -> request_module();
				rtnl_lock();
				for (...) {
				  tcf_action_init_1();
				    -> tcf_idr_check_alloc();
				   // Insert one action into idr,
				   // but it is not committed until
				   // tcf_idr_insert_many(), then drop
				   // the RTNL lock in the _next_
				   // iteration
				   -> rtnl_unlock();
    -> rtnl_lock();
    -> a_o->init();
      -> tcf_idr_check_alloc();
      // Now waiting for the same index
      // to be committed
				    -> request_module();
				    -> rtnl_lock()
				    // Now waiting for RTNL lock
				}
				rtnl_unlock();
}
rtnl_unlock();

This is not easy to solve, we can move the request_module() before
this loop and pre-load all the modules we need for this netlink
message and then do the rest initializations. So the loop breaks down
to two now:

        for (i = 1; i <= TCA_ACT_MAX_PRIO && tb[i]; i++) {
                struct tc_action_ops *a_o;

                a_o = tc_action_load_ops(name, tb[i]...);
                ops[i - 1] = a_o;
        }

        for (i = 1; i <= TCA_ACT_MAX_PRIO && tb[i]; i++) {
                act = tcf_action_init_1(ops[i - 1]...);
        }

Although this looks serious, it only has been reported by syzbot, so it
seems hard to trigger this by humans. And given the size of this patch,
I'd suggest to make it to net-next and not to backport to stable.

This patch has been tested by syzbot and tested with tdc.py by me.

Fixes: 0fedc63f ("net_sched: commit action insertions together")
Reported-and-tested-by: syzbot+82752bc5331601cf4899@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+b3b63b6bff456bd95294@syzkaller.appspotmail.com
Reported-by: syzbot+ba67b12b1ca729912834@syzkaller.appspotmail.com
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20210117005657.14810-1-xiyou.wangcong@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Defining DEBUG should only be done in development.
So remove DEBUG.
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210115235346.289611-1-trix@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Xin Long says:

====================
net: make udp tunnel devices support fraglist

Like GRE device, UDP tunnel devices should also support fraglist, so
that some protocol (like SCTP) HW GSO that requires NETIF_F_FRAGLIST
in the dev can work. Especially when the lower device support both
NETIF_F_GSO_UDP_TUNNEL and NETIF_F_GSO_SCTP.
====================

Link: https://lore.kernel.org/r/cover.1610704037.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Like vxlan and geneve, bareudp also needs this dev feature
to support some protocol's HW GSO.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Some protocol HW GSO requires fraglist supported by the device, like
SCTP. Without NETIF_F_FRAGLIST set in the dev features of geneve, it
would have to do SW GSO before the packets enter the driver, even
when the geneve dev and lower dev (like veth) both have the feature
of NETIF_F_GSO_SCTP.

So this patch is to add it for geneve.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Some protocol HW GSO requires fraglist supported by the device, like
SCTP. Without NETIF_F_FRAGLIST set in the dev features of vxlan, it
would have to do SW GSO before the packets enter the driver, even
when the vxlan dev and lower dev (like veth) both have the feature
of NETIF_F_GSO_SCTP.

So this patch is to add it for vxlan.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

For additional robustness in the face of Hyper-V errors or malicious
behavior, validate all values that originate from packets that Hyper-V
has sent to the guest.  Ensure that invalid values cannot cause indexing
off the end of an array, or subvert an existing validation via integer
overflow.  Ensure that outgoing packets do not have any leftover guest
memory that has not been zeroed out.
Reported-by: Juan Vazquez <juvazq@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Link: https://lore.kernel.org/r/20210114202628.119541-1-parri.andrea@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Replace some checks for ETH_P_8021Q and ETH_P_8021AD with
eth_type_vlan().
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210117080950.122761-1-dong.menglong@zte.com.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Alex Elder says:

====================
net: ipa: interconnect improvements

The main outcome of this series is to allow the number of
interconnects used by the IPA to differ from the three that
are implemented now.  With this series in place, any number
of interconnects can now be used, all specified in the
configuration data for a specific platform.

A few minor interconnect-related cleanups are implemented as well.
====================

Link: https://lore.kernel.org/r/20210115125050.20555-1-elder@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently we assume that the IPA hardware has exactly three
interconnects.  But that won't be guaranteed for all platforms,
so allow any number of interconnects to be specified in the
configuration data.

For each platform, define an array of interconnect data entries
(still associated with the IPA clock structure), and record the
number of entries initialized in that array.

Loop over all entries in this array when initializing, enabling,
disabling, or tearing down the set of interconnects.

With this change we no longer need the ipa_interconnect_id
enumerated type, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pass an the address of an IPA interconnect structure and its
configuration data to ipa_interconnect_init_one() and have that
function initialize all the structure's fields.  Change the function
to simply return an error code.

Introduce ipa_interconnect_exit_one() to encapsulate the cleanup of
an IPA interconnect structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add the name to the configuration data for each interconnect.  Use
this information rather than a constant string during initialization.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add fields in the ipa_interconnect structure to hold the average and
peak bandwidth values for the interconnect.  Pass the configuring
data for interconnects to ipa_interconnect_init() so these values
can be recorded, and use them when enabling the interconnects.

There's no longer any need to keep a copy of the interconnect data
after initialization.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Rather than having separate pointers for the memory, imem, and
config interconnect paths, maintain an array of ipa_interconnect
structures each of which contains a pointer to a path.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If disabling interconnects fails there's not a lot we can do.  The
only two callers of ipa_interconnect_disable() ignore the return
value, so just give the function a void return type.

Print an error message if disabling any of the interconnects is not
successful.  Return (and print) only the first error seen.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use "bandwidth" rather than "rate" in describing the average and
peak values to use for IPA interconnects.  They should have been
named that way to begin with.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Xin Long says:

====================
net: fix the features flag in sctp_gso_segment

Patch 1/2 is to improve the code in skb_segment(), and it is needed
by Patch 2/2.
====================

Link: https://lore.kernel.org/r/cover.1610703289.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

It makes more sense to clear NETIF_F_SG instead of set it when
calling skb_segment() in sctp_gso_segment(), since SCTP GSO is
using head_skb's fraglist, of which all frags are linear skbs.

This will make SCTP GSO code more understandable.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

After commit 89319d38 ("net: Add frag_list support to skb_segment"),
it goes to process frag_list when !hsize in skb_segment(). However, when
using skb frag_list, sg normally should not be set. In this case, hsize
will be set with len right before !hsize check, then it won't go to
frag_list processing code.

So the right thing to do is move the hsize check to the else block, so
that it won't affect the !hsize check for frag_list processing.

v1->v2:
  - change to do "hsize <= 0" check instead of "!hsize", and also move
    "hsize < 0" into else block, to save some cycles, as Alex suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

fix semicolon.cocci warnings:
drivers/net/ethernet/mscc/ocelot_net.c:460:2-3: Unneeded semicolon
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20210115095544.33164-1-vulab@iscas.ac.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Enable interrupt based Tx completions to improve latency for T5.
The consumer index (CIDX) will now come via interrupts so that Tx
SKBs can be freed up sooner in Rx path. Also, enforce CIDX flush
threshold override (CIDXFTHRESHO) to improve latency for slow
traffic. This ensures that the interrupt is generated immediately
whenever hardware catches up with driver (i.e. CIDX == PIDX is
reached), which is often the case for slow traffic.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Link: https://lore.kernel.org/r/20210115102059.6846-1-rajur@chelsio.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Lee Jones says:

====================
Rid W=1 warnings in Ethernet

This set is part of a larger effort attempting to clean-up W=1
kernel builds, which are currently overwhelmingly riddled with
niggly little warnings.

v2:
 - Squashed IBM patches
 - Fixed real issue in SMSC
 - Added Andrew's Reviewed-by tags on remainder
====================

Link: https://lore.kernel.org/r/20210115200905.3470941-1-lee.jones@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/net/ethernet/toshiba/spider_net.c:263: warning: Function parameter or member 'hwdescr' not described in 'spider_net_get_descr_status'
 drivers/net/ethernet/toshiba/spider_net.c:263: warning: Excess function parameter 'descr' description in 'spider_net_get_descr_status'
 drivers/net/ethernet/toshiba/spider_net.c:554: warning: Function parameter or member 'netdev' not described in 'spider_net_get_multicast_hash'
 drivers/net/ethernet/toshiba/spider_net.c:902: warning: Function parameter or member 't' not described in 'spider_net_cleanup_tx_ring'
 drivers/net/ethernet/toshiba/spider_net.c:902: warning: Excess function parameter 'card' description in 'spider_net_cleanup_tx_ring'
 drivers/net/ethernet/toshiba/spider_net.c:1074: warning: Function parameter or member 'card' not described in 'spider_net_resync_head_ptr'
 drivers/net/ethernet/toshiba/spider_net.c:1234: warning: Function parameter or member 'napi' not described in 'spider_net_poll'
 drivers/net/ethernet/toshiba/spider_net.c:1234: warning: Excess function parameter 'netdev' description in 'spider_net_poll'
 drivers/net/ethernet/toshiba/spider_net.c:1278: warning: Function parameter or member 'p' not described in 'spider_net_set_mac'
 drivers/net/ethernet/toshiba/spider_net.c:1278: warning: Excess function parameter 'ptr' description in 'spider_net_set_mac'
 drivers/net/ethernet/toshiba/spider_net.c:1350: warning: Function parameter or member 'error_reg1' not described in 'spider_net_handle_error_irq'
 drivers/net/ethernet/toshiba/spider_net.c:1350: warning: Function parameter or member 'error_reg2' not described in 'spider_net_handle_error_irq'
 drivers/net/ethernet/toshiba/spider_net.c:1968: warning: Function parameter or member 't' not described in 'spider_net_link_phy'
 drivers/net/ethernet/toshiba/spider_net.c:1968: warning: Excess function parameter 'data' description in 'spider_net_link_phy'
 drivers/net/ethernet/toshiba/spider_net.c:2149: warning: Function parameter or member 'work' not described in 'spider_net_tx_timeout_task'
 drivers/net/ethernet/toshiba/spider_net.c:2149: warning: Excess function parameter 'data' description in 'spider_net_tx_timeout_task'
 drivers/net/ethernet/toshiba/spider_net.c:2182: warning: Function parameter or member 'txqueue' not described in 'spider_net_tx_timeout'
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/net/ethernet/toshiba/ps3_gelic_net.c:1107: warning: Function parameter or member 'irq' not described in 'gelic_card_interrupt'
 drivers/net/ethernet/toshiba/ps3_gelic_net.c:1107: warning: Function parameter or member 'ptr' not described in 'gelic_card_interrupt'
 drivers/net/ethernet/toshiba/ps3_gelic_net.c:1407: warning: Function parameter or member 'txqueue' not described in 'gelic_net_tx_timeout'
 drivers/net/ethernet/toshiba/ps3_gelic_net.c:1439: warning: Function parameter or member 'napi' not described in 'gelic_ether_setup_netdev_ops'
 drivers/net/ethernet/toshiba/ps3_gelic_net.c:1639: warning: Function parameter or member 'dev' not described in 'ps3_gelic_driver_probe'
 drivers/net/ethernet/toshiba/ps3_gelic_net.c:1795: warning: Function parameter or member 'dev' not described in 'ps3_gelic_driver_remove'
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fixes the following W=1 kernel build warning(s):

 from drivers/net/ethernet/ibm/ibmvnic.c:35:
 inlined from ‘handle_vpd_rsp’ at drivers/net/ethernet/ibm/ibmvnic.c:4124:3:
 drivers/net/ethernet/ibm/ibmvnic.c:1362: warning: Function parameter or member 'hdr_field' not described in 'build_hdr_data'
 drivers/net/ethernet/ibm/ibmvnic.c:1362: warning: Function parameter or member 'skb' not described in 'build_hdr_data'
 drivers/net/ethernet/ibm/ibmvnic.c:1362: warning: Function parameter or member 'hdr_len' not described in 'build_hdr_data'
 drivers/net/ethernet/ibm/ibmvnic.c:1362: warning: Function parameter or member 'hdr_data' not described in 'build_hdr_data'
 drivers/net/ethernet/ibm/ibmvnic.c:1423: warning: Function parameter or member 'hdr_field' not described in 'create_hdr_descs'
 drivers/net/ethernet/ibm/ibmvnic.c:1423: warning: Function parameter or member 'hdr_data' not described in 'create_hdr_descs'
 drivers/net/ethernet/ibm/ibmvnic.c:1423: warning: Function parameter or member 'len' not described in 'create_hdr_descs'
 drivers/net/ethernet/ibm/ibmvnic.c:1423: warning: Function parameter or member 'hdr_len' not described in 'create_hdr_descs'
 drivers/net/ethernet/ibm/ibmvnic.c:1423: warning: Function parameter or member 'scrq_arr' not described in 'create_hdr_descs'
 drivers/net/ethernet/ibm/ibmvnic.c:1474: warning: Function parameter or member 'txbuff' not described in 'build_hdr_descs_arr'
 drivers/net/ethernet/ibm/ibmvnic.c:1474: warning: Function parameter or member 'num_entries' not described in 'build_hdr_descs_arr'
 drivers/net/ethernet/ibm/ibmvnic.c:1474: warning: Function parameter or member 'hdr_field' not described in 'build_hdr_descs_arr'
 drivers/net/ethernet/ibm/ibmvnic.c:1832: warning: Function parameter or member 'adapter' not described in 'do_change_param_reset'
 drivers/net/ethernet/ibm/ibmvnic.c:1832: warning: Function parameter or member 'rwi' not described in 'do_change_param_reset'
 drivers/net/ethernet/ibm/ibmvnic.c:1832: warning: Function parameter or member 'reset_state' not described in 'do_change_param_reset'
 drivers/net/ethernet/ibm/ibmvnic.c:1911: warning: Function parameter or member 'adapter' not described in 'do_reset'
 drivers/net/ethernet/ibm/ibmvnic.c:1911: warning: Function parameter or member 'rwi' not described in 'do_reset'
 drivers/net/ethernet/ibm/ibmvnic.c:1911: warning: Function parameter or member 'reset_state' not described in 'do_reset'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/net/ethernet/ti/am65-cpts.c:736: warning: Function parameter or member 'en' not described in 'am65_cpts_rx_enable'
 drivers/net/ethernet/ti/am65-cpts.c:736: warning: Excess function parameter 'skb' description in 'am65_cpts_rx_enable'
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/net/ethernet/ti/am65-cpsw-qos.c:364: warning: Function parameter or member 'ndev' not described in 'am65_cpsw_timer_set'
 drivers/net/ethernet/ti/am65-cpsw-qos.c:364: warning: Function parameter or member 'est_new' not described in 'am65_cpsw_timer_set'
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/net/xen-netback/xenbus.c:419: warning: Function parameter or member 'dev' not described in 'frontend_changed'
 drivers/net/xen-netback/xenbus.c:419: warning: Function parameter or member 'frontend_state' not described in 'frontend_changed'
 drivers/net/xen-netback/xenbus.c:1001: warning: Function parameter or member 'dev' not described in 'netback_probe'
 drivers/net/xen-netback/xenbus.c:1001: warning: Function parameter or member 'id' not described in 'netback_probe'
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fixes the following W=1 kernel build warning(s):

 drivers/net/ethernet/smsc/smc91x.c:2200: warning: Function parameter or member 'dev' not described in 'try_toggle_control_gpio'
 drivers/net/ethernet/smsc/smc91x.c:2200: warning: Function parameter or member 'desc' not described in 'try_toggle_control_gpio'
 drivers/net/ethernet/smsc/smc91x.c:2200: warning: Function parameter or member 'name' not described in 'try_toggle_control_gpio'
 drivers/net/ethernet/smsc/smc91x.c:2200: warning: Function parameter or member 'index' not described in 'try_toggle_control_gpio'
 drivers/net/ethernet/smsc/smc91x.c:2200: warning: Function parameter or member 'value' not described in 'try_toggle_control_gpio'
 drivers/net/ethernet/smsc/smc91x.c:2200: warning: Function parameter or member 'nsdelay' not described in 'try_toggle_control_gpio'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Following patch add support for flow based tunneling API
to send and recv GTP tunnel packet over tunnel metadata API.
This would allow this device integration with OVS or eBPF using
flow based tunneling APIs.
Signed-off-by: Pravin B Shelar <pbshelar@fb.com>
Link: https://lore.kernel.org/r/20210110070021.26822-1-pbshelar@fb.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In bictcp_reset(), use memset and offsetof instead of = 0.
Signed-off-by: Yejune Deng <yejune.deng@gmail.com>
Link: https://lore.kernel.org/r/1610597696-128610-1-git-send-email-yejune.deng@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Replace some checks for ETH_P_8021Q and ETH_P_8021AD in
drivers/net/tap.c with eth_type_vlan.
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Link: https://lore.kernel.org/r/20210115023238.4681-1-dong.menglong@zte.com.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use the struct member w of the struct urelease_work directly instead of
casting it.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Link: https://lore.kernel.org/r/f0ed86d6d54ac0834bd2e161d172bf7bb5647cf7.1610683862.git.geliangtang@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Vladimir Oltean says:

====================
Configuring congestion watermarks on ocelot switch using devlink-sb

In some applications, it is important to create resource reservations in
the Ethernet switches, to prevent background traffic, or deliberate
attacks, from inducing denial of service into the high-priority traffic.

These patches give the user some knobs to turn. The ocelot switches
support per-port and per-port-tc reservations, on ingress and on egress.
The resources that are monitored are packet buffers (in cells of 60
bytes each) and frame references.

The frames that exceed the reservations can optionally consume from
sharing watermarks which are not per-port but global across the switch.
There are 10 sharing watermarks, 8 of them are per traffic class and 2
are per drop priority.

I am configuring the hardware using the best of my knowledge, and mostly
through trial and error. Same goes for devlink-sb integration. Feedback
is welcome.
====================

Link: https://lore.kernel.org/r/20210115021120.3055988-1-olteanv@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Using devlink-sb, we can configure 12/16 (the important 75%) of the
switch's controlling watermarks for congestion drops, and we can monitor
50% of the watermark occupancies (we can monitor the reservation
watermarks, but not the sharing watermarks, which are exposed as pool
sizes).

The following definitions can be made:

SB_BUF=0 # The devlink-sb for frame buffers
SB_REF=1 # The devlink-sb for frame references
POOL_ING=0 # The pool for ingress traffic. Both devlink-sb instances
           # have one of these.
POOL_EGR=1 # The pool for egress traffic. Both devlink-sb instances
           # have one of these.

Editing the hardware watermarks is done in the following way:
BUF_xxxx_I is accessed when sb=$SB_BUF and pool=$POOL_ING
REF_xxxx_I is accessed when sb=$SB_REF and pool=$POOL_ING
BUF_xxxx_E is accessed when sb=$SB_BUF and pool=$POOL_EGR
REF_xxxx_E is accessed when sb=$SB_REF and pool=$POOL_EGR

Configuring the sharing watermarks for COL_SHR(dp=0) is done implicitly
by modifying the corresponding pool size. By default, the pool size has
maximum size, so this can be skipped.

devlink sb pool set pci/0000:00:00.5 sb $SB_BUF pool $POOL_ING \
	size 129840 thtype static

Since by default there is no buffer reservation, the above command has
maxed out BUF_COL_SHR_I(dp=0).

Configuring the per-port reservation watermark (P_RSRV) is done in the
following way:

devlink sb port pool set pci/0000:00:00.5/0 sb $SB_BUF \
	pool $POOL_ING th 1000

The above command sets BUF_P_RSRV_I(port 0) to 1000 bytes. After this
command, the sharing watermarks are internally reconfigured with 1000
bytes less, i.e. from 129840 bytes to 128840 bytes.

Configuring the per-port-tc reservation watermarks (Q_RSRV) is done in
the following way:

for tc in {0..7}; do
	devlink sb tc bind set pci/0000:00:00.5/0 sb 0 tc $tc \
		type ingress pool $POOL_ING \
		th 3000
done

The above command sets BUF_Q_RSRV_I(port 0, tc 0..7) to 3000 bytes.
The sharing watermarks are again reconfigured with 24000 bytes less.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This is meant to be a gentle introduction into the world of watermarks
on ocelot. The code is placed in ocelot_devlink.c because it will be
integrated with devlink, even if it isn't right now.

My first step was intended to be to replicate the default configuration
of the congestion watermarks programatically, since they are now going
to be tuned by the user.

But after studying and understanding through trial and error how they
work, I now believe that the configuration used out of reset does not do
justice to the word "reservation", since the sum of all reservations
exceeds the total amount of resources (otherwise said, all reservations
cannot be fulfilled at the same time, which means that, contrary to the
reference manual, they don't guarantee anything).

As an example, here's a dump of the reservation watermarks for frame
buffers, for port 0 (for brevity, the ports 1-6 were omitted, but they
have the same configuration):

BUF_Q_RSRV_I(port 0, prio 0) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 1) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 2) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 3) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 4) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 5) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 6) = max 3000 bytes
BUF_Q_RSRV_I(port 0, prio 7) = max 3000 bytes

Otherwise said, every port-tc has an ingress reservation of 3000 bytes,
and there are 7 ports in VSC9959 Felix (6 user ports and 1 CPU port).
Concentrating only on the ingress reservations, there are, in total,
8 [traffic classes] x 7 [ports] x 3000 [bytes] = 168,000 bytes of memory
reserved on ingress.
But, surprise, Felix only has 128 KB of packet buffer in total...
A similar thing happens with Seville, which has a larger packet buffer,
but also more ports, and the default configuration is also overcommitted.

This patch disables the (apparently) bogus reservations and moves all
resources to the shared area. This way, real reservations can be set up
by the user, using devlink-sb.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add devlink integration into the mscc_ocelot switchdev driver. All
physical ports (i.e. the unused ones as well) except the CPU port module
at ocelot->num_phys_ports are registered with devlink, and that requires
keeping the devlink_port structure outside struct ocelot_port_private,
since the latter has a 1:1 mapping with a struct net_device (which does
not exist for unused ports).

Since we use devlink_port_type_eth_set to link the devlink port to the
net_device, we can as well remove the .ndo_get_phys_port_name and
.ndo_get_port_parent_id implementations, since devlink takes care of
retrieving the port name and number automatically, once
.ndo_get_devlink_port is implemented.

Note that the felix DSA driver is already integrated with devlink by
default, since that is a thing that the DSA core takes care of. This is
the reason why these devlink stubs were put in ocelot_net.c and not in
the common library. It is also the reason why ocelot::devlink is a
pointer and not a full structure embedded inside struct ocelot: because
the mscc_ocelot driver allocates that by itself (as the container of
struct ocelot, in fact), but in the case of felix, it is DSA who
allocates the devlink, and felix just propagates the pointer towards
struct ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This is a leftover of commit 69df578c ("net: mscc: ocelot: eliminate
confusion between CPU and NPI port") which renamed that function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We should be moving anything that isn't DSA-specific or SoC-specific out
of the felix DSA driver, and into the common mscc_ocelot switch library.

The number of traffic classes is one of the aspects that is common
between all ocelot switches, so it belongs in the library.

This patch also makes seville use 8 TX queues, and therefore enables
prioritization via the QOS_CLASS field in the NPI injection header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>