The new Lenovo Haswell series (-40's) contains a new Synaptics touchpad.
However, these new Synaptics devices report bad axis ranges.
Under Windows, it is not a problem because the Windows driver uses RMI4
over SMBus to talk to the device. Under Linux, we are using the PS/2
fallback interface and it occurs the reported ranges are wrong.

Of course, it would be too easy to have only one range for the whole
series, each touchpad seems to be calibrated in a different way.

We can not use SMBus to get the actual range because I suspect the firmware
will switch into the SMBus mode and stop talking through PS/2 (this is the
case for hybrid HID over I2C / PS/2 Synaptics touchpads).

So as a temporary solution (until RMI4 land into upstream), start a new
list of quirks with the min/max manually set.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The cypress PS/2 trackpad models supported by the cypress_ps2 driver
emulate BTN_RIGHT events in firmware based on the finger position, as part
of this no motion events are sent when the finger is in the button area.

The INPUT_PROP_BUTTONPAD property is there to indicate to userspace that
BTN_RIGHT events should be emulated in userspace, which is not necessary
in this case.

When INPUT_PROP_BUTTONPAD is advertised userspace will wait for a motion
event before propagating the button event higher up the stack, as it needs
current abs x + y data for its BTN_RIGHT emulation. Since in the
cypress_ps2 pads don't report motion events in the button area, this means
that clicks in the button area end up being ignored, so
INPUT_PROP_BUTTONPAD actually causes problems for these touchpads, and
removing it fixes:

https://bugs.freedesktop.org/show_bug.cgi?id=76341Reported-by: Adam Williamson <awilliam@redhat.com>
Tested-by: Adam Williamson <awilliam@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The wrong register bit of the DA9052/3 PMIC registers was
used to determine the status on the ONKEY.

Also a failure in reading the status register will no longer
result in the work queue being rescheduled as that would result
in a (potentially) endless retry.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Acked-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

As discussed here: http://ez.analog.com/message/35852, the 5587 revC and
5588 revB spec sheets contain a mistake in the GPIO_DAT_STATx register
description.

According to R.Shnell at ADI, as well as my own observations, it should
read: "GPIO data status (shows GPIO state when read for inputs)".

This commit changes the get value function accordingly.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

First round of input updates for 3.14.

Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

features->quirks can have multiple bits set. For dual input, we only
need to check WACOM_QUIRK_MULTI_INPUT.
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Simplify the error path and remove() function by using devm_*
functions for requesting gpios and irq and allocating the input
device.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Pass through the 0xE1 prefix so atkbd can properly parse the scancode
data.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Since the driver requires DT now we do not need to check if CONFIG_OF is
defined.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add device tree support for twl4030 keypad driver.

Tested on Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We should drop reference to twl6040_core_node device_node once we are done
using it.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We should drop reference to twl6040_core_node device_node once we are done
using it.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Remove messy dependencies from SERIO_I8042 by having it depend on one
Kconfig symbol (ARCH_MIGHT_HAVE_PC_SERIO) and having architectures
which need it select ARCH_MIGHT_HAVE_PC_SERIO in arch/*/Kconfig.
New architectures are unlikely to need SERIO_I8042, so this avoids
having an ever growing list of architectures to exclude.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO. Cayman board
is only sh board which needs this.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Architectures which might use an i8042 for serial IO to keyboard,
mouse, etc should select ARCH_MIGHT_HAVE_PC_SERIO.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This enables the rumble force feedback on the F710 unit since
it is no longer treated as XTYPE_UNKNOWN type.
Signed-off-by: Petr Sebor <petr@scssoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When using Razer Onza controller the dpad doesn't work in many games
because D-PAD was mapped to buttons (useful for dance pads) and not to
HAT0X/Y axis.

ers who really want to have it mapped to buttons can restore previous
behavior by using 'dpad_to_buttons' module option.
Signed-off-by: Thomaz de Oliveira dos Reis <thor27@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We need to make sure we allocate absinfo data when we are setting one of
EV_ABS/ABS_XXX capabilities, otherwise we may bomb when we try to emit this
event.
Rested-by: Paul Cercueil <pcercuei@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver can't deal with two entries its keymap having the same keycode.
When this happens it will get confused about whether the key is down or up
and will cause some screwy behavior.

We need to have two entries for KEY_BACKSLASH to handle US and UK
keyboards. Specifically:
* On the US keyboard the backslash key (above enter) is r3 c11 and is
  supposed to be reported as BACKSLASH.
* On the UK keyboard the # key (left of enter) is r4 c10 and is
  supposed to be reported as BACKSLASH.
* On the UK keyboard the \ key (left of Z) is r2 c7 and is supposed to
  be reported as KEY_102ND.

Note that both keyboards (US and UK) have only one physical backslash
key so the constraint that each physical key should have its own keycode
still stands.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Commit 2203747c ("ARM: omap: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Commit a3b29245 ("ARM: ep93xx: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This simplifies error handling and device removal paths.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

free_irq() in the error handling case is missing when change
pass input device directly to interrupt.

Fixes: b27f8fee('Input: pmic8xxx-pwrkey - pass input device directly to interrupt')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This adds support for another flavor of ALPS protocol used in newer
"Dolphin" devices.
Signed-off-by: Yunkang Tang <yunkang.tang@cn.alps.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fix some typos and while at it also use "PS" as the name for the central
"HOME" button on Sony controllers, this is how Sony itself calls it.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The error code was not set if unable to set config, so the error
condition wasn't reflected in the return value. Fix to return a
negative error code from the error handling case instead of 0.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The current assumption in the elantech driver that hw version 3 touchpads
are never clickpads and hw version 4 touchpads are always clickpads is
wrong.

There are several bug reports for this, ie:
https://bugzilla.redhat.com/show_bug.cgi?id=1030802
http://superuser.com/questions/619582/right-elantech-touchpad-button-not-working-in-linux

I've spend a couple of hours wading through various bugzillas, launchpads
and forum posts to create a list of fw-versions and capabilities for
different laptop models to find a good method to differentiate between
clickpads and versions with separate hardware buttons.

Which shows that a device being a clickpad is reliable indicated by bit 12
being set in the fw_version. I've included the gathered list inside the
driver, so that we've this info at hand if we need to revisit this later.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some devices with support for mobile networks may have buttons for
enabling/disabling such connection. An example can be Linksys router 54G3G.
We already have KEY_BLUETOOTH, KEY_WLAN and KEY_UWB so it makes sense to
add KEY_WWAN as well.  As we already have KEY_WIMAX, use it's value for
KEY_WWAN and make it an alias.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When waking up the platform by pressing a specific key, sending a
release on that key makes it impossible to react on the event in
user-space. This is fixed by moving the input_reset_device() call to
resume instead.

[dmitry.torokhov@gmail.com: make sure we still restore LED/sound state
after resume, handle hibernation properly]
Signed-off-by: Aleksej Makarov <aleksej.makarov@sonymobile.com>
Signed-off-by: Oskar Andero <oskar.andero@sonymobile.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>