Add support to fetch the SFP EEPROM settings from the firmware
and display it via the ethtool -m command.  We support SFP+ and QSFP
modules.

v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When there is only 1 MSI-X vector or in INTA mode, tx and rx pre-set
max channel parameters are shown incorrectly in ethtool -l.  With only 1
vector, bnxt_get_max_rings() will return -ENOMEM.  bnxt_get_channels
should check this return value, and set max_rx/max_tx to 0 if it is
non-zero.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.

The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.

Conflicts:
	drivers/net/wireless/intel/iwlwifi/mvm/tx.c
	net/ipv4/ip_gre.c
	net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix mvneta/bm dependencies, from Arnd Bergmann.

 2) RX completion hw bug workaround in bnxt_en, from Michael Chan.

 3) Kernel pointer leak in nf_conntrack, from Linus.

 4) Hoplimit route attribute limits not enforced properly, from Paolo
    Abeni.

 5) qlcnic driver NULL deref fix from Dan Carpenter.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  arm64: bpf: jit JMP_JSET_{X,K}
  net/route: enforce hoplimit max value
  nf_conntrack: avoid kernel pointer value leak in slab name
  drivers: net: xgene: fix register offset
  drivers: net: xgene: fix statistics counters race condition
  drivers: net: xgene: fix ununiform latency across queues
  drivers: net: xgene: fix sharing of irqs
  drivers: net: xgene: fix IPv4 forward crash
  xen-netback: fix extra_info handling in xenvif_tx_err()
  net: mvneta: bm: fix dependencies again
  bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)
  bnxt_en: Add workaround to detect bad opaque in rx completion (part 1)
  qlcnic: potential NULL dereference in qlcnic_83xx_get_minidump_template()

Switchdev has been around for quite a while now, putting "EXPERIMENTAL"
in the description is no longer accurate, drop it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Original implementation commit e54bcde3 ("arm64: eBPF JIT compiler")
had the relevant code paths, but due to an oversight always fail jiting.

As a result, we had been falling back to BPF interpreter whenever a BPF
program has JMP_JSET_{X,K} instructions.

With this fix, we confirm that the corresponding tests in lib/test_bpf
continue to pass, and also jited.

...
[    2.784553] test_bpf: #30 JSET jited:1 188 192 197 PASS
[    2.791373] test_bpf: #31 tcpdump port 22 jited:1 325 677 625 PASS
[    2.808800] test_bpf: #32 tcpdump complex jited:1 323 731 991 PASS
...
[    3.190759] test_bpf: #237 JMP_JSET_K: if (0x3 & 0x2) return 1 jited:1 110 PASS
[    3.192524] test_bpf: #238 JMP_JSET_K: if (0x3 & 0xffffffff) return 1 jited:1 98 PASS
[    3.211014] test_bpf: #249 JMP_JSET_X: if (0x3 & 0x2) return 1 jited:1 120 PASS
[    3.212973] test_bpf: #250 JMP_JSET_X: if (0x3 & 0xffffffff) return 1 jited:1 89 PASS
...

Fixes: e54bcde3 ("arm64: eBPF JIT compiler")
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when creating or updating a route, no check is performed
in both ipv4 and ipv6 code to the hoplimit value.

The caller can i.e. set hoplimit to 256, and when such route will
 be used, packets will be sent with hoplimit/ttl equal to 0.

This commit adds checks for the RTAX_HOPLIMIT value, in both ipv4
ipv6 route code, substituting any value greater than 255 with 255.

This is consistent with what is currently done for ADVMSS and MTU
in the ipv4 code.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The slab name ends up being visible in the directory structure under
/sys, and even if you don't have access rights to the file you can see
the filenames.

Just use a 64-bit counter instead of the pointer to the 'net' structure
to generate a unique name.

This code will go away in 4.7 when the conntrack code moves to a single
kmemcache, but this is the backportable simple solution to avoiding
leaking kernel pointers to user space.

Fixes: 5b3501fa ("netfilter: nf_conntrack: per netns nf_conntrack_cachep")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull vfs fixes from Al Viro:
 "Overlayfs fixes from Miklos, assorted fixes from me.

  Stable fodder of varying severity, all sat in -next for a while"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ovl: ignore permissions on underlying lookup
  vfs: add lookup_hash() helper
  vfs: rename: check backing inode being equal
  vfs: add vfs_select_inode() helper
  get_rock_ridge_filename(): handle malformed NM entries
  ecryptfs: fix handling of directory opening
  atomic_open(): fix the handling of create_error
  fix the copy vs. map logics in blk_rq_map_user_iov()
  do_splice_to(): cap the size before passing to ->splice_read()

Iyappan Subramanian says:

====================
drivers: net: xgene: Bug fixes

This patch set addresses the following bug fixes that were found during testing.

  1. IPv4 forward test crash
    - drivers: net: xgene: fix IPv4 forward crash

  2. Sharing of irqs
    - drivers: net: xgene: fix sharing of irqs

  3. Ununiform latency across queues
    - drivers: net: xgene: fix ununiform latency across queues

  4. Fix statistics counters race condition
    - drivers: net: xgene: fix statistics counters race condition

  5. Correcting register offset and field lengths
    - drivers: net: xgene: fix register offset

v2: Address review comments from v1
- Defer TSO fix, and reposting all other patches from v1

v1:
- Initial version
====================
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes SG_RX_DV_GATE_REG_0_ADDR register offset
and ring state field lengths.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the race condition on updating the statistics
counters by moving the counters to the ring structure.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch addresses ununiform latency across queues by adding
more queues to match with, upto number of CPU cores.

Also, number of interrupts are increased and the channel numbers
are reordered.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since hardware doesn't allow sharing of interrupts,
this patch fixes the same by removing IRQF_SHARED flag.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the crash observed during IPv4 forward test by
setting the drop field in the dbptr.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2016-05-13

This series contains updates to e1000e, igb and igbvf.

Steve Shih fixes an issue for disabling auto-negotiation and forcing
speed and duplex settings for non-copper media.

Brian Walsh cleanups some inconsistency in the use of return variables
names to avoid confusion.

Jake cleans up the drivers to use the BIT() macro when it can, which will
future proof the drivers for GCC 6 when it gets released.  Cleaned up
dead code which was never being used.  Also fixed e1000e, where it was
incorrectly restting the SYSTIM registers every time the ioctl was being
run.

Denys Vlasenko fixes an oversight where incvalue variable holds a 32
bit value so we should declare it as such, instead of 64 bits.  Also
fixed an overflow check, where two reads are the same, then it is not
an overflow.

Nathan Sullivan fixes the PTP timestamps for transmit and receive
latency based on the current link speed.

Alexander Duyck adds support for partial GSO segmentation in the case
of tunnels for igb and igbvf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull cgroup fixes from Tejun Heo:
 "During v4.6-rc1 cgroup namespace support was merged.  There is an
  issue where it's impossible to tell whether a given cgroup mount point
  is bind mounted or namespaced.  Serge has been working on the issue
  but it took longer than expected to resolve, so the late pull request.

  Given that it's a completely new feature and the patches don't touch
  anything else, the risk seems acceptable.  However, if this is too
  late, an alternative is plugging new cgroup ns creation for v4.6 and
  retrying for v4.7"

* 'for-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: fix compile warning
  kernfs: kernfs_sop_show_path: don't return 0 after seq_dentry call
  cgroup, kernfs: make mountinfo show properly scoped path for cgroup namespaces
  kernfs_path_from_node_locked: don't overwrite nlen

Pull workqueue fix from Tejun Heo:
 "CPU hotplug callbacks can invoke DOWN_FAILED w/o preceding
  DOWN_PREPARE which can trigger a WARN_ON() in workqueue.

  The bug has been there for a very long time.  It only triggers if CPU
  down fails at a specific point and I don't think it has adverse
  effects other than the warning messages.  The fix is very low impact"

* 'for-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: fix rebind bound workers warning

The e1000e_config_hwtstamp function was incorrectly resetting the SYSTIM
registers every time the ioctl was being run. If you happened to be
running ptp4l and lost the PTP connect (removing cable, or blocking the
UDP traffic for example), then ptp4l will eventually perform a restart
which involves re-requesting timestamp settings. In e1000e this has the
unfortunate and incorrect result of resetting SYSTIME to the kernel
time. Since kernel time is usually in UTC, and PTP time is in TAI, this
results in the leap second being re-applied.

Fix this by extracting the SYSTIME reset out into its own function,
e1000e_ptp_reset, which we call during reset to restore the hardware
registers. This function will (a) restart the timecounter based on the
new system time, (b) restore the previous PPB setting, and (c) restore
the previous hwtstamp settings.

In order to perform (b), I had to modify the adjfreq ptp function
pointer to store the old delta each time it is called. This also has the
side effect of restoring the correct base timinca register correctly.
The driver does not need to explicitly zero the ptp_delta variable since
the entire adapter structure comes zero-initialized.
Reported-by: Brian Walsh <brian@walsh.ws>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for partial GSO segmentation in the case of
tunnels.  Specifically with this change the driver an perform segmentation
as long as the frame either has IPv6 inner headers, or we are allowed to
mangle the IP IDs on the inner header.  This is needed because we will not
be modifying any fields from the start of the start of the outer transport
header to the start of the inner transport header as we are treating them
like they are just a block of IP options.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The E1000_ICH_NVM_SIG_MASK value is shifted, out to the 31st bit, which
is the signed bit for signed constants. Mark these values as unsigned to
prevent compiler warnings and issues on platforms which a different
signed bit implementation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This prevents signed bitshift issues when the shift would overwrite the
signed bit, and prevents making this mistake in the future when copying
and modifying code.

Use GENMASK or the unsigned postfix for cases which aren't suitable for
BIT() macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

To prevent signed bitshift issues, and improve code readability, use the
BIT() macro. Also make use of GENMASK or the unsigned postfix where this
is more appropriate than BIT()
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The variable rdlen is set but never used, and thus setting it is dead
code. Remove it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Table 7-62 on page 338 of the i210 datasheet lists TX and RX latencies
for the various speeds the chip supports.  To give better PTP timestamp
accuracy, adjust the timestamps by the amounts Intel gives based on
current link speed.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

SYSTIMH:SYSTIML registers are incremented by 24-bit value TIMINCA[23..0]

er32(SYSTIML) are probably moderately expensive (they are pci bus reads).
Can we avoid one of them? Yes, we can.

If the SYSTIML value we see is smaller than 0xff000000, the overflow
into SYSTIMH would require at least two increments.

We do two reads, er32(SYSTIML) and er32(SYSTIMH), in this order.

Even if one increment happens between them, the overflow into SYSTIMH
is impossible, and we can avoid doing another er32(SYSTIML) read
and overflow check.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If two consecutive reads of the counter are the same, it is also
not an overflow.  "systimel_1 < systimel_2" should be
"systimel_1 <= systimel_2".

Before the patch, we could perform an *erroneous* correction:

Let's say that systimel_1 == systimel_2 == 0xffffffff.
"systimel_1 < systimel_2" is false, we think it's an overflow,
we read "systimeh = er32(SYSTIMH)" which meanwhile had incremented,
and use "(systimeh << 32) + systimel_2" value which is 2^32 too large.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: intel-wired-lan@lists.osuosl.org
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

"incvalue" variable holds a result of "er32(TIMINCA) &
E1000_TIMINCA_INCVALUE_MASK" and used in "do_div(temp, incvalue)"
as a divisor.

Thus, "u64 incvalue" declaration is probably a mistake.
Even though it seems to be a harmless one, let's fix it.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

For bitshifts, we should make use of the BIT macro when possible, and
ensure that other bitshifts are marked as unsigned. This helps prevent
signed bitshift errors, and ensures similar style.

Make use of GENMASK and the unsigned postfix where BIT() isn't
appropriate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixed the file to use a consistent ret_val for return value checking.
Signed-off-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the issues for disabling auto-negotiation and forcing
speed and duplex settings for the non-copper media.

For non-copper media, e1000_get_settings should return ETH_TP_MDI_INVALID for
eth_tp_mdix_ctrl instead of ETH_TP_MDI_AUTO so subsequent e1000_set_settings
call would not fail with -EOPNOTSUPP.

e1000_set_spd_dplx should not automatically turn autoneg back on for forced
1000 Mbps full duplex settings for non-copper media.

Cc: xe-kernel@external.cisco.com
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Steve Shih <sshih@cisco.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull scheduler fix from Ingo Molnar:
 "This is a revert to fix an interactivity problem.

  The proper fixes for the problems that the reverted commit exposed are
  now in sched/core (consisting of 3 patches), but were too risky for
  v4.6 and will arrive in the v4.7 merge window"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Revert "sched/fair: Fix fairness issue on migration"

Pull perf fixes from Ingo Molnar:
 "An uncharacteristically large number of bugs popped up in the last
  week:

   - various tooling fixes, two crashes and build problems
   - two Intel PT fixes
   - an KNL uncore driver fix
   - an Intel PMU driver fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf stat: Fallback to user only counters when perf_event_paranoid > 1
  perf evsel: Handle EACCESS + perf_event_paranoid=2 in fallback()
  perf evsel: Improve EPERM error handling in open_strerror()
  tools lib traceevent: Do not reassign parg after collapse_tree()
  perf probe: Check if dwarf_getlocations() is available
  perf dwarf: Guard !x86_64 definitions under #ifdef else clause
  perf tools: Use readdir() instead of deprecated readdir_r()
  perf thread_map: Use readdir() instead of deprecated readdir_r()
  perf script: Use readdir() instead of deprecated readdir_r()
  perf tools: Use readdir() instead of deprecated readdir_r()
  perf/core: Disable the event on a truncated AUX record
  perf/x86/intel/pt: Generate PMI in the STOP region as well
  perf/x86: Fix undefined shift on 32-bit kernels
  perf/x86/msr: Fix SMI overflow
  perf/x86/intel/uncore: Fix CHA registers configuration procedure for Knights Landing platform
  perf diff: Fix duplicated output column

Pull ARM SoC fixes from Arnd Bergmann:
 "Three more bug fixes for ARM SoCs this week:

   - The Atmel sama5d2 was registering the wrong NFC device type

   - On Atmel sam9x5, the power management controller had an incorrect
     register area size

   - On ARM64 Allwinner machine was not secting the generic irqchip
     code, causing build errors in some configurations"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: at91: sam9x5: Fix the memory range assigned to the PMC
  arm64/sunxi: 4.6-rc1: Add dependency on generic irq chip
  ARM: dts: at91: sama5d2: use "atmel,sama5d3-nfc" compatible for nfc

Merge tag 'regulator-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator fixes from Mark Brown:
 "A small collection of driver specific fixes for the regulator
  subsysetem:

   - Fix handling of probe deferral for GPIO regulators

   - Fix a typo in the module alias for DA9053

   - Fix the definition of BUCK9 in the S2MPS11 driver.  This change
     looks larger than it is because an irregularity in the hardware
     means that the macro used to define bucks 6-10 needs duplicating
     and tweaking to have a separate macro for 9

   - Fix a series of errors in the definitions of the LDOs the AXP20x
     regulators, some of which had always been present and some of which
     were introduced in the merge window"

* tag 'regulator-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: da9063: Correct module alias prefix to fix module autoloading
  regulator: axp20x: Fix axp22x ldo_io registration error on cold boot
  regulator: axp20x: Fix axp22x ldo_io voltage ranges
  regulator: axp20x: Fix LDO4 linear voltage range
  regulator: s2mps11: Fix invalid selector mask and voltages for buck9
  regulator: gpio: check return value of of_get_named_gpio

Pull regmap fixes from Mark Brown:
 "This is rather too late so it'd be completely understandable if you
  don't want to pull it at this point, I had thought I'd sent this
  earlier but it seems I didn't.  Everything has been in -next for some
  time now.

  The main set of fixes here are mopping up some more issues with MMIO,
  fixing handling of endianness configuration in DT (which just wasn't
  working at all) and cases where the register and value endianness are
  different.

  There is also a fix for bulk register reads on SPMI"

* tag 'regmap-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: spmi: Fix regmap_spmi_ext_read in multi-byte case
  regmap: mmio: Explicitly say little endian is the defualt in the bus config
  regmap: mmio: Parse endianness definitions from DT
  regmap: Fix implicit inclusion of device.h
  regmap: mmio: Fix value endianness selection
  regmap: fix documentation to match code

Pull media fix from Mauro Carvalho Chehab:
 "A revert fixing a breakage that caused an OOPS on all VB2-based DVB
  drivers.

  We already have a proper fix, but it sounds safer to keep it being
  tested for a while and not hurry, to avoid the risk of another
  regression, specially since this is meant to be c/c to stable.  So,
  for now, let's just revert the broken patch"

* tag 'media/v4.6-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  Revert "[media] videobuf2-v4l2: Verify planes array in buffer dequeueing"

Pull drm fixes from Dave Airlie:
 "A bunch of radeon displayport mode setting fixes, and some misc i915
  fixes.

  There is one revert, the MST audio code in i915 was causing some
  oopses, so we've decided just to drop it until next kernel when we can
  fix it properly"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/amdgpu: fix DP mode validation
  drm/radeon: fix DP mode validation
  drm/i915: Bail out of pipe config compute loop on LPT
  drm/radeon: fix PLL sharing on DCE6.1 (v2)
  drm/radeon: fix DP link training issue with second 4K monitor
  Revert "drm/i915: start adding dp mst audio"
  drm/i915/bdw: Add missing delay during L3 SQC credit programming
  drm/i915/lvds: separate border enable readout from panel fitter
  drm/i915: Update CDCLK_FREQ register on BDW after changing cdclk frequency

Pull crypto fix from Herbert Xu:
 "This fixes a bug in the RSA self-test that may cause crashes on some
  architectures such as SPARC"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: testmgr - Use kmalloc memory for RSA input