The conditions that one specific PE's frozen count exceeds the maximal
allowed times (EEH_MAX_ALLOWED_FREEZES) and it's in isolated or recovery
state indicate the PE was removed permanently implicitly. The patch
introduces flag EEH_PE_REMOVED to indicate that explicitly so that we
don't depend on the fixed maximal allowed times, which can be varied as
we do in subsequent patch.

Flag EEH_PE_REMOVED is expected to be marked for the PE whose frozen
count exceeds the maximal allowed times, or just failed from recovery.
Requested-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

PE#0 should be regarded as valid for P7IOC, while it's invalid for
PHB3. The patch adds flag EEH_VALID_PE_ZERO to differentiate those
two cases. Without the patch, we possibly see frozen PE#0 state is
cleared without EEH recovery taken on P7IOC as following kernel logs
indicate:

[root@ltcfbl8eb ~]# dmesg
       :
pci 0000:00     : [PE# 000] Secondary bus 0 associated with PE#0
pci 0000:01     : [PE# 001] Secondary bus 1 associated with PE#1
pci 0001:00     : [PE# 000] Secondary bus 0 associated with PE#0
pci 0001:01     : [PE# 001] Secondary bus 1 associated with PE#1
pci 0002:00     : [PE# 000] Secondary bus 0 associated with PE#0
pci 0002:01     : [PE# 001] Secondary bus 1 associated with PE#1
pci 0003:00     : [PE# 000] Secondary bus 0 associated with PE#0
pci 0003:01     : [PE# 001] Secondary bus 1 associated with PE#1
pci 0003:20     : [PE# 002] Secondary bus 32..63 associated with PE#2
       :
EEH: Clear non-existing PHB#3-PE#0
EEH: PHB location: U78AE.001.WZS00M9-P1-002
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When calling to early_setup(), we pick "boot_paca" up for the master CPU
and initialize that with initialise_paca(). At that point, the SLB
shadow buffer isn't populated yet. Updating the SLB shadow buffer should
corrupt what we had in physical address 0 where the trap instruction is
usually stored.

This hasn't been observed to cause any trouble in practice, but is
obviously fishy.

Fixes: 6f4441ef ("powerpc: Dynamically allocate slb_shadow from memblock")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

num_possible_cpus() is just a shorthand for it.
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Currently, all non-dot symbols are being treated as function descriptors
in ABIv1. This is incorrect and is resulting in perf probe not working:

  # perf probe do_fork
  Added new event:
  Failed to write event: Invalid argument
    Error: Failed to add events.
  # dmesg | tail -1
  [192268.073063] Could not insert probe at _text+768432: -22

perf probe bases all kernel probes on _text and writes,
for example, "p:probe/do_fork _text+768432" to
/sys/kernel/debug/tracing/kprobe_events. In-kernel, _text is being
considered to be a function descriptor and is resulting in the above
error.

Fix this by changing how we lookup symbol addresses on ppc64. We first
check for the dot variant of a symbol and look at the non-dot variant
only if that fails. In this manner, we avoid having to look at the
function descriptor.

While at it, also separate out how this works on ABIv2 where
we don't have dot symbols, but need to use the local entry point.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Once upon a time, at least 9 years ago (< 2.6.12), _TIF_SYSCALL_T_OR_A
meant "TRACE or AUDIT". But these days it means TRACE or AUDIT or
SECCOMP or TRACEPOINT or NOHZ.

All of those are implemented via syscall_dotrace() so rename the flag to
that to try and clarify things.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We removed the last usage of CPU_FTR_IABR in commit 1ad7d705
"powerpc/xmon: Enable HW instruction breakpoint on POWER8".

Mark it as free.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>

mpe: Fix compile errors and formatting. Add tempfile logic to Makefile.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch includes all of the powerpc test binaries into the .gitignore
file listing in their respective directories. This will make sure that
git ignores all of these test binaries when displaying status.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

pci_dn->phb is set to phb in update_dn_pci_info(), if succeed.

This patch removes the duplication of pci_dn->phb initialization.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When IOMMU bypass is enabled, a PCI device can read and write memory
that was not mapped by the driver without causing an EEH. That might
cause memory corruption, for example.

When we disable bypass, DMA reads and writes to addresses not mapped by
the IOMMU will cause an EEH, allowing us to debug such issues.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The current handling of EPOW_SHUTDOWN_ON_UPS event does not shutdown the
system after logging the message. All the events of EPOW_SYSTEM_SHUTDOWN
action code (EPOW_SHUTDOWN_ON_UPS is a part of it) must initiate system
shutdown as per the SPAPR spec. If the LPAR does not shutdown after
receiving this rtas based event, it will expose itself to a forced
abrupt shutdown initiated by the platform firmware. This patch fixes the
situation.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The M64 range information is missed in dmesg, which would be helpful in debug.

This patch prints the M64 range information in the same format as M32.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Adds reset to sysfs which will PERST the card. If load_image_on_perst is set
to "user" or "factory", the PERST will cause that image to be loaded.

load_image_on_perst is set to "user" for production.

"none" could be used for debugging. The PSL trace arrays are preserved which
then can be read through debugfs.

PERST also triggers CAPP recovery. An HMI comes in, which is handled by EEH.
EEH unbinds the driver, calls into Sapphire to reinitialize the PHB, then
rebinds the driver.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Turning snoops on is the last step in CAPP recovery. Sapphire is expected to
have reinitialized the PHB and done the previous recovery steps.

Add mode argument to opal call to do this. Driver can turn snoops off although
it does not currently.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

load_image_on_perst identifies whether a PERST will cause the image to be
flashed to the card. And if so, which image.

Valid entries are: "none", "user" and "factory".

A value of "none" means PERST will not cause the image to be flashed. A
power cycle to the pcie slot is required to load the image.

"user" loads the user provided image and "factory" loads the factory image upon
PERST.

sysfs updates the cxl struct in the driver then calls cxl_update_image_control
to write the vals in the VSEC.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Select defaults such that a PERST causes flash image reload.  Select which
image based on what the card is set up to load.

CXL_VSEC_PERST_LOADS_IMAGE selects whether PERST assertion causes flash image
load.

CXL_VSEC_PERST_SELECT_USER selects which image is loaded on the next PERST.

cxl_update_image_control writes these bits into the VSEC.
Signed-off-by: Ryan Grimm <grimm@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This fixes two typos and explains where shared attributes are stored.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch adds tracepoints throughout the cxl driver, which can provide
insight into:

- Context lifetimes
- Commands sent to the PSL and AFU and their completion status
- Segment and page table misses and their resolution
- PSL and AFU interrupts
- slbia calls from the powerpc copro_fault code

These tracepoints are mostly intended to aid in debugging (particularly
for new AFU designs), and may be useful standalone or in conjunction
with hardware traces collected by the PSL (read out via the trace
interface in debugfs) and AFUs.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

hwirq has not been initialized, however it is being incremented
and also not being referenced in a loop.  This error was detected with
cppcheck:

[drivers/misc/cxl/irq.c:439]: (error) Uninitialized variable: hwirq

Commit 80fa93fc ("cxl: Name interrupts in /proc/interrupt")
introduced this error.

This is a simple fix that removes the redundant increment.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-By: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fixes warnings like these:

  drivers/ps3/sys-manager-core.c: error: symbol 'ps3_sys_manager_power_off' redeclared with different type
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fix sparse warnings like these:

  drivers/ps3/ps3-vuart.c: warning: symbol 'ps3_vuart_disable_interrupt_tx' was not declared. Should it be static?
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add calls to the ps3_mm_set_repository_highmem() routine when the ps3
r1 highmem region is either created or destroyed.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add the new routine ps3_mm_set_repository_highmem() that saves highmem info to
the LV1 hypervisor registry so that the info will be available to second stage
OS's loaded by petitboot/kexec. FreeBSD and some Linux derivatives use
this feature.

Also, move the existing ps3_mm_get_repository_highmem() routine up in
the source file.

This implementation of ps3_mm_set_repository_highmem() assumes the repository
will have a single highmem region entry (at index 0).
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

To avoid the need for preprocessor conditionals in C source files add a set of
empty inline repository highmem write routines to platform.h that are used when
CONFIG_PS3_REPOSITORY_WRITE is not defined.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add CGROUPS and DEVTMPFS, which allows booting with newer userspaces.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Distros are enabling NUMA balancing (eg Ubuntu), so it would be good to
get some more test coverage with it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Enable config options required by lxc and docker.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

KSM will only be used on areas marked for merging via madvise, and it
is showing nice improvements on KVM workloads, so enable it by
default.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We are starting to see ppc64 boxes with SATA AHCI adapters in it,
so enable it in our defconfigs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This was enabled on the pseries defconfigs recently, but missed
the ppc64 one.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

It looks like it's ~4 years since we updated some of these, so do a bulk
update.

Verified that the before and after generated configs are exactly the
same.

Which begs the question why update them? The answer is that it can be
confusing when the stored defconfig drifts too far from the generated
result.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We have two arrays in kvm_host_state that contain register values for
the PMU. Currently we only create an asm-offsets symbol for the base of
the arrays, and do the array offset in the assembly code.

Creating an asm-offsets symbol for each field individually makes the
code much nicer to read, particularly for the MMCRx/SIxR/SDAR fields, and
might have helped us notice the recent double restore bug we had in this
code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Alexander Graf <agraf@suse.de>

In the Makefile, string.o (which is generated from string.S) is
included into the list of objects being built unconditionally
(obj-y) in line 12.

Additionally, if CONFIG_PPC64 is set, it is included again in
line 17.

This patch removes the latter unnecessary inclusion.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Commit 2a2c74b2 ("IBM Akebono: Add the Akebono platform") added a
select of IBM_EMAC_RGMII_WOL. But that Kconfig symbol isn't (yet) part
of the tree. So this select has been a nop since that commit was
included in v3.16-rc1.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When we deactivate the AFU directed mode we free the scheduled process
area, but did not clear the register in the hardware that has a pointer
to it.

This should be fine since we will have already cleared out every context
and we won't do anything that would cause the hardware to access it
until after we have allocated a new one, but just to be safe this patch
clears out the register when we free the page.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Upon inspection of the implementation specific registers, it was
discovered that the high bit of the implementation specific RXCTL
register was enabled, which enables the DEADB00F debug feature.

The debug feature causes MMIO reads to a disabled AFU to respond with
0xDEADB00F instead of all Fs. In general this should not be visible as
the kernel will only allow MMIO access to enabled AFUs, but there may be
some circumstances where an AFU may become disabled while it is use.
One such case would be an AFU designed to only be used in the dedicated
process mode and to disable itself after it has completed it's work
(however even in that case the effects of this debug flag would be
limited as the userspace application must have completed any required
MMIO accesses before the AFU disables itself with or without the flag).

This patch removes the debug flag and replaces the magic value
programmed into this register with a preprocessor define so it is
clearer what the rest of this initialisation does.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

If a context is being detached and we get a translation fault for it
there is little point getting it's mm and handling the fault, so just
respond with an address error and return earlier.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>