We don't want to trigger moving between PS mode during scan,
because then we will sometimes end up sending nullfunc frames
during scan. We're supposed to only send one prior to scan
and after scan.

This fixes an oops which occured due to an assert in ath9k:

http://marc.info/?l=linux-wireless&m=124277331319024

The assert was happening because the rate control algorithm
figures it should find at least one valid dual stream or
single stream rate. Since we allow mac80211 to send nullfunc
frames during scan and dynamic PS was enabled at times we ended
up trying to send nullfunc frames for the target sta on the
wrong band for which we have no valid rate to communicate with
it. This breaks the assumptions in rate control.

We determine we also need to disable moving between PS modes
when not associated so lets just add that now as well, and we
should not have a ps_sdata when that interface cannot actually
go into PS because it's not associated.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Always enable rfkill since the ifdefs in the code is not really worth
the Kconfig option.  Also fix a few code style things, and remove the
usage of the ah_gpio[] array so we can remove it later.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The return type has more than two values, but it can validly
only ever return TX_DROP and TX_CONTINUE, so use a bool
instead of ieee80211_tx_result.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Always use the wiphy name instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch along with my previous patch in mac80211 "Fix the
way ADDBA count..", fixes hang in tx when connected to an HT
AP which rejects/times out on addba req.

AGGR_ADDBA_PROGRESS should be cleared in aggr state when addba
negotiation is terminated due to either addba response is timed out
or addba is denied by the AP. With out clearing this bit,
all frames are queued onto s/w queue for getting tx'd as aggr and
will never be scheduled onto hw queue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

addba_req_num[tid] is supposed to have the count of consecutive
addba request attempts on 'tid' which failed. This count is checked
against a retry threshold (3 times) before starting the addba negotiation.
This patch fixes the way this addba count is incremented/reset and thereby
avoids indefinite addba attempts.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As Pavel puts userspace can be stupid and should not
cause kernel crashes. In this case Pavel was able to
find a crash here but unable to reproduce. Either way
lets deal with this.

This should fix:

------------[ cut here ]------------
kernel BUG at /home/proski/src/linux-2.6/net/wireless/reg.c:2132!
Oops: Exception in kernel mode, sig: 5 [#1]
PowerMac
Modules linked in: ath5k ath [last unloaded: scsi_wait_scan]
NIP: c02f3eac LR: c02f3d08 CTR: 00000000
REGS: ef107aa0 TRAP: 0700   Not tainted  (2.6.30-rc8-wl)
MSR: 00029032 <EE,ME,CE,IR,DR>  CR: 88002442  XER: 20000000
TASK = ef84acb0[834] 'crda' THREAD: ef106000
GPR00: ef953840 ef107b50 ef84acb0 ef1380bc 00000006 c035a5c8 ef107b90 c035a5c8
GPR08: 00080005 efb68980 c0445628 ef130004 28002422 10019ce0 10012d3c 00000001
GPR16: 1070b2ac 00000005 48023558 1070b380 4802304c 00000000 ef107ddc c035a5c8
GPR24: ef107b78 c0443350 ef8bcb00 00000005 ef138080 c04a6a70 c04a0000 ef8bcb00
NIP [c02f3eac] set_regdom+0x4c4/0x4ec
LR [c02f3d08] set_regdom+0x320/0x4ec
Call Trace:
[ef107b50] [c02f3d08] set_regdom+0x320/0x4ec (unreliable)
[ef107b70] [c02f9d10] nl80211_set_reg+0x140/0x2d0
[ef107bc0] [c02aa2b8] genl_rcv_msg+0x204/0x228
[ef107c10] [c02a97cc] netlink_rcv_skb+0xe8/0x10c
[ef107c30] [c02aa094] genl_rcv+0x3c/0x5c
[ef107c40] [c02a9050] netlink_unicast+0x308/0x36c
[ef107c80] [c02a92bc] netlink_sendmsg+0x208/0x2f0
[ef107cd0] [c0282048] sock_sendmsg+0xac/0xe4
[ef107db0] [c02822b4] sys_sendmsg+0x234/0x2d8
[ef107f00] [c0283a88] sys_socketcall+0x108/0x258
[ef107f40] [c0012790] ret_from_syscall+0x0/0x38
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add automagic feature flags, so the firmware can tell the driver
about supported features and the driver can switch features on/off as
needed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Once rfkill-input is disabled, the "global" states will only be used as
default initial states.

Since the states will always be the same after resume, we shouldn't
generate events on resume.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The re-written rfkill core ensures rfkill devices are initialized to
the system default state.  The core calls set_block after registration
so the driver shouldn't need to.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rfkill_set_global_sw_state() (previously rfkill_set_default()) will no
longer be exported by the rewritten rfkill core.

Instead, platform drivers which can provide persistent soft-rfkill state
across power-down/reboot should indicate their initial state by calling
rfkill_set_sw_state() before registration.  Otherwise, they will be
initialized to a default value during registration by a set_block call.

We remove existing calls to rfkill_set_sw_state() which happen before
registration, since these had no effect in the old model.  If these
drivers do have persistent state, the calls can be put back (subject
to testing :-).  This affects hp-wmi and acer-wmi.

Drivers with persistent state will affect the global state only if
rfkill-input is enabled.  This is required, otherwise booting with
wireless soft-blocked and pressing the wireless-toggle key once would
have no apparent effect.  This special case will be removed in future
along with rfkill-input, in favour of a more flexible userspace daemon
(see Documentation/feature-removal-schedule.txt).

Now rfkill_global_states[n].def is only used to preserve global states
over EPO, it is renamed to ".sav".
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In order to handle powersave frames properly we had needed
to pass these out to the device queues again, and introduce
the skb->requeue bit. This, however, also has unnecessary
overhead by needing to 'clean up' already tried frames, and
this clean-up code is also buggy when software encryption
is used.

Instead of sending the frames via the master netdev queue
again, simply put them into the pending queue. This also
fixes a problem where frames for that particular station
could be reordered when some were still on the software
queues and older ones are re-injected into the software
queue after them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

During the rfkill conversion I added code to call
sony_nc_rfkill_set with the wrong argument, causing
a segfault Reinette reported. The compiler could not
catch that because the argument is, and needs to be,
void *.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Now that we added the ioctl, there's no need to ask
the user to configure this. We will keep it enabled
for now, and eventually swap the default to n. Also
let embedded users select it only if they need it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This ports the b43/legacy rfkill code to the new API offered
by cfg80211 and thus removes a lot of useless stuff.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch introduces initial rfkill support for the ath5k driver
based on rfkill support in the cfg80211 framework.
All rfkill related code is separated into newly created rfkill.c.

Changes to existing code are minimal:

* added a new data structure ath5k_rfkill to the ath5k_softc structure
* inserted calls to HW rfkill init/deinit routines
* ath5k_intr() has been extended to handle AR5K_INT_GPIO interrupts
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is useful for debugging when we know if something disabled
the in-kernel rfkill input handler.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch is a back-port from aggregation testing code.

In the past, we didn't limit the amount of active tx urbs.
However, ar9170 only has a limited buffer reserved for
pending data frames.

This wasn't much of a problem with the slower 802.11b/g.
We simply stopped the full queue and moved on to something different
in the mean time. But - as you guessed it -  this simple approach
stands in way for a decent aggregation implementation.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds new commands that the original firmware will not send
but we can use them to debug firmware.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 is checking is the skb is aligned on 32 bit boundary.
But it is checking against ethernet header, whereas Linux expect IP
header aligned.  And ethernet ether size is 6*2+2=14, so aligning
ethernet header make IP header unaligned.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix possible unaligned u32 access in b43_generate_plcp_hdr().
Unaligned data is read/write with a u32 pointer instead of using the
packed structure. Some versions of gcc ignore the "packed" attribute, if the
structure element is accessed through a local pointer.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The minstrel rate controller periodically looks up rate indexes in
a sampling table.  When accessing a specific row and column, minstrel
correctly does a bounds check which, on the surface, appears to handle
the case where mi->n_rates < 2.  However, mi->sample_idx is actually
defined as an unsigned, so the right hand side is taken to be a huge
positive number when negative, and the check will always fail.

Consequently, the RC will overrun the array and cause random memory
corruption when communicating with a peer that has only a single rate.
The max value of mi->sample_idx is around 25 so casting to int should
have no ill effects.

Without the change, uptime is a few minutes under load with an AP
that has a single hard-coded rate, and both the AP and STA could
potentially crash.  With the change, both lasted 12 hours with a
steady load.

Thanks to Ognjen Maric for providing the single-rate clue so I could
reproduce this.

This fixes http://bugzilla.kernel.org/show_bug.cgi?id=12490 on the
regression list (also http://bugzilla.kernel.org/show_bug.cgi?id=13000).

Cc: stable@kernel.org
Reported-by: Sergey S. Kostyliov <rathamahata@gmail.com>
Reported-by: Ognjen Maric <ognjen.maric@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This removes the dependency on GPIO framework and lets the SPI host
driver handle the chip select. The SPI host driver is required to keep
the CS active for the entire message unless cs_change says otherwise.
This patch collects the two/three single SPI transfers into a message.
Also the delay in read path in case use_dummy_writes are not used is
moved into the SPI host driver.
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Driver used to be named rndis_wext before inclusion to upstream. Since
rndis_wlan is being converted to cfg80211, use of rndis_wext* names
can be confusing. So rename all rndis_wext to rndis_wlan (as should
have been when driver was renamed).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Capitalize enum labels as told in Documents/CodingStyle.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This ports the iwlwifi rfkill code to the new API offered by
cfg80211 and thus removes a lot of useless stuff. The soft-
rfkill is completely removed since that is now handled by
setting the interfaces down.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since we use ERR_PTR and similar macros, we need to include
linux/err.h.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to check if a pointer is NULL before calling
vfree(), since vfree() function already check for it.
Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Include offloaded FCoE data into total rx/tx statistics for 82599 so they
are properly reflected by ethtool or ifconfig.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ethtool is a standard way of getting information about
ethernet interfaces.  We enhance ethtool kernel interface
& e1000e to make the MDI-X status readable via ethtool in
userspace.
Signed-off-by: Chaitanya Lala <clala@riverbed.com>
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e_config_collision_dist() sets tctl, but subsequently tctl is
overwritten.  It seems to me that as things stand the call to
e1000e_config_collision_dist() has no effect and should either be
removed or moved down a little bit.  This kernel patch takes the latter
option.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phy corruption has been observed on 2-port 82571 adapters, and is root-caused
to lack of synchronization between the 2 driver instances, which conflict
when attempting to access the phy via the single MDIC register.
A semaphore exists for this purpose, and is now used on these designs. Because
PXE &/or EFI boot code (which we cannot expect to be built with this fix) may
leave the inter-instance semaphore in an invalid initial state when the driver
first loads, this fix also includes a one-time (per driver load) fix-up of the
semaphore initial state.
Signed-off-by: dave graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fakehard is a really simple driver implementing only necessary
callbacks and serves the role of an example of driver for HardMAC
IEEE 802.15.4 device.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add MAINTAINERS entry and a small text describing our stack interfaces,
how to hook the drivers, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a netlink interface for configuration of IEEE 802.15.4 device. Also this
interface specifies events notification sent by devices towards higher layers.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for communication over IEEE 802.15.4 networks. This implementation
is neither certified nor complete, but aims to that goal. This commit contains
only the socket interface for communication over IEEE 802.15.4 networks.
One can either send RAW datagrams or use SOCK_DGRAM to encapsulate data
inside normal IEEE 802.15.4 packets.

Configuration interface, drivers and software MAC 802.15.4 implementation will
follow.

Initial implementation was done by Maxim Gorbachyov, Maxim Osipov and Pavel
Smolensky as a research project at Siemens AG. Later the stack was heavily
reworked to better suit the linux networking model, and is now maitained
as an open project partially sponsored by Siemens.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

IEEE 802.15.4 stack requires several constants to be defined/adjusted.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change PSCHED_SHIFT from 10 to 6 to increase schedulers time
resolution. This will increase 16x a number of (internal) ticks per
nanosecond, and is needed to improve accuracy of schedulers based on
rate tables, like HTB, TBF or CBQ, with rates above 100Mbit. It is
assumed this change is safe for 32bit accounting of time diffs up
to 2 minutes, which should be enough for common use (extremely low
rate values may overflow, so get inaccurate instead). To make full
use of this change an updated iproute2 will be needed. (But using
older iproute2 should be safe too.)

This change breaks ticks - microseconds similarity, so some minor code
fixes might be needed. It is also planned to change naming adequately
eg. to PSCHED_TICKS2NS() etc. in the near future.
Reported-by: Antonio Almeida <vexwek@gmail.com>
Tested-by: Antonio Almeida <vexwek@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use PSCHED_SHIFT constant instead of '10' in PSCHED_US2NS() and
PSCHED_NS2US() macros to enable changing this value later.

Additionally use PSCHED_SHIFT in sch_hfsc SM_SHIFT and ISM_SHIFT
definitions. This part of the patch is based on feedback from
Patrick McHardy <kaber@trash.net>.
Reported-by: Antonio Almeida <vexwek@gmail.com>
Tested-by: Antonio Almeida <vexwek@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit f001fde5
(net: introduce a list of device addresses dev_addr_list (v6))
added one regression Vegard Nossum found in its testings.

With kmemcheck help, Vegard found some uninitialized memory
was read and reported to user, potentialy leaking kernel data.
( thread can be found on http://lkml.org/lkml/2009/5/30/177 )

dev_addr_init() incorrectly uses sizeof() operator. We were
initializing one byte instead of MAX_ADDR_LEN bytes.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>