The 104-dio-48e module calls devm_request_irq() for each device. If the
number of irq passed to the module does not match the number of base, a
default value of 0 is passed to devm_request_irq(). IRQ 0 is probably
not what the user wants, so utilize the module_isa_driver_with_irq macro
to ensure the number of irq matches the number of base.
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The 104-quad-8 module calls devm_request_irq() for each device. If the
number of irq passed to the module does not match the number of base, a
default value of 0 is passed to devm_request_irq(). IRQ 0 is probably
not what the user wants, so utilize the module_isa_driver_with_irq macro
to ensure the number of irq matches the number of base.
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Acked-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Several ISA drivers feature IRQ support that can configured via an "irq"
array module parameter. This array typically matches directly with the
respective "base" array module parameter. To reduce code repetition, a
module_isa_driver_with_irq helper macro is introduced to provide a check
ensuring that the number of "irq" passed to the module matches with the
respective number of "base".
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Acked-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Add support for the NXP PCAL6534. This device is broadly a 34-bit version
of the PCAL6524. However, whilst the registers are broadly what you'd
expect for a 34-bit version of the PCAL6524, the spacing of the registers
has been compacted. This has the unfortunate effect of breaking the bit
shift based mechanism that is employed to work out register locations used
by the other chips supported by this driver. To accommodate ths, callback
functions have been added to allow alterate implementations of
pca953x_recalc_addr() and pca953x_check_register() for the PCAL6534.

Datasheet: https://www.nxp.com/docs/en/data-sheet/PCAL6534.pdf
Datasheet: https://www.diodes.com/assets/Datasheets/PI4IOE5V6534Q.pdfSigned-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

A later patch in the series adds support for a further chip type that
shares some similarity with the PCA953X_TYPE. In order to keep the logic
simple, swap over the if and else portions where checks are made against
PCA953X_TYPE and instead check for PCA957X_TYPE.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

A previous fix, commit dc87f6dd ("gpio: pca953x: Fix
pca953x_gpio_set_config"), identified that pinconf_to_config_param() needed
to be used to isolate the config_param from the pinconf in
pca953x_gpio_set_config(). This fix however did not consider that this
would also be needed in pca953x_gpio_set_pull_up_down() to which it passes
this config.

Perform a similar call in pca953x_gpio_set_pull_up_down() to isolate the
configuration parameter there as well, rather than passing it from
pca953x_gpio_set_config() as the configuration argument may also be needed
in pca953x_gpio_set_pull_up_down() at a later date.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The NXP PCAL6534 is a 34-bit I2C I/O expander similar to the PCAL6524. The
Diodes PI4IOE5V6534Q is a functionally identical chip provided by Diodes
Inc.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Diodes Incorporated is a manufacturer of application specific standard
products within the discrete, logic, analog, and mixed-signal semiconductor
markets.

https://www.diodes.com/Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Mt7621 SoC GPIO driver is a platform driver so we can directly use
'platform_get_irq' instead of 'irq_of_parse_and_map'.
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The NXP PCAL6408 is the 8-bit version of PCAL6416.
Signed-off-by: Nate Drude <nate.d@variscite.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The NXP PCAL6408 is the 8-bit version of PCAL6416.
Signed-off-by: Nate Drude <nate.d@variscite.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Document support for the GPIO controller blocks in the Renesas R-Car
V4H (R8A779G0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

When EXAR xr17v35x chips are cascaded in order to access the MPIO registers
(part of the Device Configuration Registers) of the secondary chips, an offset
needs to be applied based on the number of primary chip's UART channels.
Signed-off-by: Qingtao Cao <qingtao.cao@digi.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

There are no external users of fwnode_get_named_gpiod() anymore, so
let's stop exporting it and mark it as static.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Merge tag 'platform-drivers-x86-simatec-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86 into gpio/for-next

Tag (immutable branch) for:
v6.0-rc1 + "[PATCH v6 0/7] add support for another simatic board" series
for merging into the gpio, leds and pdx86 subsystems.

This adds support for the Siemens Simatic IPC427G. A board which
basically works like the 227G added in a previous patch. So all there is
to do is to add the station_id and make it take all the 227G branches.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Link: https://lore.kernel.org/r/20220825104422.14156-8-henning.schild@siemens.comReviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Just load the watchdog module, after having identified that machine.
That watchdog module does not have any autoloading support.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Link: https://lore.kernel.org/r/20220825104422.14156-7-henning.schild@siemens.comReviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

This adds support of the Siemens Simatic IPC227G. Its LEDs are connected
to GPIO pins provided by the gpio-f7188x module. We make sure that
gets loaded, if not enabled in the kernel config no LED support will be
available.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Link: https://lore.kernel.org/r/20220825104422.14156-6-henning.schild@siemens.comSigned-off-by: Hans de Goede <hdegoede@redhat.com>

So that drivers building on top can find those pins with GPIO_LOOKUP
helpers.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220825104422.14156-5-henning.schild@siemens.comSigned-off-by: Hans de Goede <hdegoede@redhat.com>

Add GPIO support for Nuvoton NCT6116 chip. Nuvoton SuperIO chips are
very similar to the ones from Fintek. In other subsystems they also
share drivers and are called a family of drivers.

For the GPIO subsystem the only difference is that the direction bit is
reversed and that there is only one data bit per pin. On the SuperIO
level the logical device is another one.

On a chip level we do not have a manufacturer ID to check and also no
revision.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220825104422.14156-4-henning.schild@siemens.comSigned-off-by: Hans de Goede <hdegoede@redhat.com>

Subsequent patches will touch that file, apply some nice to have style
changes before actually adding functional changes.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220825104422.14156-3-henning.schild@siemens.comSigned-off-by: Hans de Goede <hdegoede@redhat.com>

Subsequent patches will touch that file, apply some nice to have style
changes before actually adding functional changes.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <brgl@bgdev.pl>
Link: https://lore.kernel.org/r/20220825104422.14156-2-henning.schild@siemens.comSigned-off-by: Hans de Goede <hdegoede@redhat.com>

STMPE driver does not require a specific node name anymore, only the
compatible is checked, update binding according to this.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The SCU firmware on i.MX8 platforms provides a set of APIs to
control the GPIO PINs on the SCU domain. This patch implements the
standard GPIO driver interface to access those PINs on the
SCU domain over the SCU APIs.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Add the description for imx-scu gpio subnode.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Add binding document for the imx scu gpio driver.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The SD card and eMMC on PolarFire SoC are sometimes muxed using a GPIO
by the bootloader. Add a hog child property to facilitate this.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Follow commit dbd1c54f ("gpio: Bulk conversion to
generic_handle_domain_irq()").
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

The UCB1400 implements a GPIO driver so it needs to include the
<linux/gpio/driver.h> header, not the legacy <linux/gpio.h> header.
Compile tested on pxa_defconfig.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Instead of listing directly properties typical for SPI peripherals,
reference the spi-peripheral-props.yaml schema.  This allows using all
properties typical for SPI-connected devices, even these which device
bindings author did not tried yet.

Remove the spi-* properties which now come via spi-peripheral-props.yaml
schema, except for the cases when device schema adds some constraints
like maximum frequency.

While changing additionalProperties->unevaluatedProperties, put it in
typical place, just before example DTS.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Convert Xilinx axi gpio binding documentation to YAML.
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>

Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we
have gfp_types.h for this.

Fixes powerpc allmodconfig build:

   In file included from include/linux/nodemask.h:97,
                    from include/linux/mmzone.h:17,
                    from include/linux/gfp.h:7,
                    from include/linux/radix-tree.h:12,
                    from include/linux/idr.h:15,
                    from include/linux/kernfs.h:12,
                    from include/linux/sysfs.h:16,
                    from include/linux/kobject.h:20,
                    from include/linux/pci.h:35,
                    from arch/powerpc/kernel/prom_init.c:24:
   include/linux/random.h: In function 'add_latent_entropy':
>> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'?
      25 |         add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
         |                                              ^~~~~~~~~~~~~~
         |                                              add_latent_entropy
   include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: kernel test robot <lkp@intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull vfs lseek fix from Al Viro:
 "Fix proc_reg_llseek() breakage. Always had been possible if somebody
  left NULL ->proc_lseek, became a practical issue now"

* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  take care to handle NULL ->proc_lseek()

Easily done now, just by clearing FMODE_LSEEK in ->f_mode
during proc_reg_open() for such entries.

Fixes: 868941b1 "fs: remove no_llseek"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull more xen updates from Juergen Gross:

 - fix the handling of the "persistent grants" feature negotiation
   between Xen blkfront and Xen blkback drivers

 - a cleanup of xen.config and adding xen.config to Xen section in
   MAINTAINERS

 - support HVMOP_set_evtchn_upcall_vector, which is more compliant to
   "normal" interrupt handling than the global callback used up to now

 - further small cleanups

* tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections
  xen: remove XEN_SCRUB_PAGES in xen.config
  xen/pciback: Fix comment typo
  xen/xenbus: fix return type in xenbus_file_read()
  xen-blkfront: Apply 'feature_persistent' parameter when connect
  xen-blkback: Apply 'feature_persistent' parameter when connect
  xen-blkback: fix persistent grants negotiation
  x86/xen: Add support for HVMOP_set_evtchn_upcall_vector

Merge tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull more perf tool updates from Arnaldo Carvalho de Melo:

 - 'perf c2c' now supports ARM64, adjust its output to cope with
   differences with what is in x86_64. Now go find false sharing on
   ARM64 (at least Neoverse) as well!

 - Refactor the JSON processing, making the output more compact and thus
   reducing the size of the resulting perf binary

 - Improvements for 'perf offcpu' profiling, including tracking child
   processes

 - Update Intel JSON metrics and events files for broadwellde,
   broadwellx, cascadelakex, haswellx, icelakex, ivytown, jaketown,
   knightslanding, sapphirerapids, skylakex and snowridgex

 - Add 'perf stat' JSON output and a 'perf test' entry for it

 - Ignore memfd and anonymous mmap events if jitdump present

 - Refactor 'perf test' shell tests allowing subdirs

 - Fix an error handling path in 'parse_perf_probe_command()'

 - Fixes for the guest Intel PT tracing patchkit in the 1st batch of
   this merge window

 - Print debuginfod queries if -v option is used, to explain delays in
   processing when debuginfo servers are enabled to fetch DSOs with
   richer symbol tables

 - Improve error message for 'perf record -p not_existing_pid'

 - Fix openssl and libbpf feature detection

 - Add PMU pai_crypto event description for IBM z16 on 'perf list'

 - Fix typos and duplicated words on comments in various places

* tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (81 commits)
  perf test: Refactor shell tests allowing subdirs
  perf vendor events: Update events for snowridgex
  perf vendor events: Update events and metrics for skylakex
  perf vendor events: Update metrics for sapphirerapids
  perf vendor events: Update events for knightslanding
  perf vendor events: Update metrics for jaketown
  perf vendor events: Update metrics for ivytown
  perf vendor events: Update events and metrics for icelakex
  perf vendor events: Update events and metrics for haswellx
  perf vendor events: Update events and metrics for cascadelakex
  perf vendor events: Update events and metrics for broadwellx
  perf vendor events: Update metrics for broadwellde
  perf jevents: Fold strings optimization
  perf jevents: Compress the pmu_events_table
  perf metrics: Copy entire pmu_event in find metric
  perf pmu-events: Hide the pmu_events
  perf pmu-events: Don't assume pmu_event is an array
  perf pmu-events: Move test events/metrics to JSON
  perf test: Use full metric resolution
  perf pmu-events: Hide pmu_events_map
  ...

Pull powerpc fixes from Michael Ellerman:

 - Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit
   CPUs trap on it rather than ignoring it as they should.

 - Fix ftrace when building with clang, which was broken by some
   refactoring.

 - A couple of other minor fixes.

Thanks to Christophe Leroy, Naveen N.  Rao, Nick Desaulniers, Ondrej
Mosnacek, Pali Rohár, Russell Currey, and Segher Boessenkool.

* tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/kexec: Fix build failure from uninitialised variable
  powerpc/ppc-opcode: Fix PPC_RAW_TW()
  powerpc64/ftrace: Fix ftrace for clang builds
  powerpc: Make eh value more explicit when using lwarx
  powerpc: Don't hide eh field of lwarx behind a macro
  powerpc: Fix eh field when calling lwarx on PPC32

Pull /proc/mounts fix from Al Viro:
 "Fix for /proc/mounts escaping - escape the '#' character too"

* tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  vfs: escape hash as well

Pull more cifs updates from Steve French:

 - two fixes for stable, one for a lock length miscalculation, and
   another fixes a lease break timeout bug

 - improvement to handle leases, allows the close timeout to be
   configured more safely

 - five restructuring/cleanup patches

* tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Do not access tcon->cfids->cfid directly from is_path_accessible
  cifs: Add constructor/destructors for tcon->cfid
  SMB3: fix lease break timeout when multiple deferred close handles for the same file.
  smb3: allow deferred close timeout to be configurable
  cifs: Do not use tcon->cfid directly, use the cfid we get from open_cached_dir
  cifs: Move cached-dir functions into a separate file
  cifs: Remove {cifs,nfs}_fscache_release_page()
  cifs: fix lock length calculation