Two simple test cases for interrupt endpoints are added to the usbtest.c file.
These are simple non-queued interrupt IN and interrupt OUT transfers. Currently,
only gadget zero is capable of executing the interrupt EP test cases. However,
extending the same to other gadgets is extremely simple and can be done
on-demand.

The two new tests added are
  - Test 25: To verify Interrupt OUT transfer
  - Test 26: To verify Interrupt IN transfer

Since the default value of wMaxPacketSize is set as 1024, so interrupt
IN transfers must be specified with the size parameter = multiple of
1024. Otherwise the default value (512) in the usbtest application fails
the transfer. See [RUN 4] for sample logs

The application logs (usbtest) and corresponding kernel logs are as
following:

[Run 1]
./testusb -a -c 10 -s 2048 -t 26 -v 511
usbtest 7-1:3.0: TEST 26: read 2048 bytes 10 times

[Run 2]
./testusb -a -c 10 -s 1024 -t 25 -v 511
usbtest 7-1:3.0: TEST 25: write 1024 bytes 10 times

[Run 3]
./testusb -a -c 10 -s 1098 -t 25 -v 511
usbtest 7-1:3.0: TEST 25: write 1098 bytes 10 times

[Run 4 - Failure case scenario]
./testusb -a  -t 26
unknown speed   /dev/bus/usb/007/004    0
/dev/bus/usb/007/004 test 26 --> 75 (Value too large for defined data type)

usbtest 7-1:3.0: TEST 26: read 512 bytes 1000 times
usb 7-1: test26 failed, iterations left 999, status -75 (not 0)
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Interrupt endpoints behave quite similar to the bulk endpoints with the
difference that the endpoints expect data sending/reception request at
particular intervals till the whole data has not been transmitted.

The interrupt EP support is added to gadget zero. A new alternate setting (=2)
has been added. It has 2 interrupt endpoints. The default parameters are set as:
	bInterval: 1 ms for FS and 8 uFrames (implying 1 ms) for HS/SS
	wMaxPacketSize: 64 bytes for FS and 1024 bytes for HS/SS
However, the same can be overridden through the module parameter interface.

The code is tested for HS and SS on a platform having DWC3 controller.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Remove the ttyGS PREFIX macro from u_serial.c and replace all occurences with
the hardcoded ttyGS string.

This macro was mostly used in a few debug/warning messages and a lot of
hardcoded ttyGS existed beneath. It may have been used for renaming the
tty, but if done so most debug messages would have ignored this.

Due to the fact the usage of this PREFIX in all debug calls would have
resulted in a hard to read/grep code it is removed completely.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Replace the VDBG and DBG macro with the kernels "proper" debug macros
(dev_vdbg and dev_dbg) in f_acm.c, f_obex.c & f_serial.c
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch makes the phy reset clk and reset line optional as this clk
is not available on boards like IFC6410 with APQ8064.

phy-reset clk is only used as argument to the mach level callbacks, so
this patch adds condition before clk_get calls so that the driver
wouldn't fail on SOCs which do not have this support.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This adds support for the USB PHY in Vybrid VF610. We assume that
the disconnection without VBUS is also needed for Vybrid.

Tests showed, without MXS_PHY_NEED_IP_FIX, enumeration of devices
behind a USB Hub fails with errors:

[  215.163507] usb usb1-port1: cannot reset (err = -32)
[  215.170498] usb usb1-port1: cannot reset (err = -32)
[  215.185120] usb usb1-port1: cannot reset (err = -32)
[  215.191345] usb usb1-port1: cannot reset (err = -32)
[  215.202487] usb usb1-port1: cannot reset (err = -32)
[  215.207718] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[  215.219317] usb usb1-port1: unable to enumerate USB device

Hence we also enable the MXS_PHY_NEED_IP_FIX flag.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Document the requirement that the request be dequeued and its
completion routine called before usb_ep_dequeue() returns. Also
fix some capitalization issues in the existing text.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>

As the driver is in mainline we can remove the version numbers.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

If uvc->control_buf is successfuly allocated but uvc->control_req
is not, uvc->control_buf is not freed in the error recovery path.
With this patch applied uvc->control_buf is freed unconditionally;
if it happens to be NULL kfree on it is safe anyway.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Activate the videobuf2 DMABUF support. As vb2-vmalloc supports the
importer role only, exporting buffers isn't supported yet. When the
exporter role will be implemented in vb2-vmalloc the UVC gadget driver
will automatically gain support for it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The disconnect of the USB Device is a common pattern for
an UVC Camera. In many cases this will give us an meaningless
information for all buffers that couldn't be enqueued.
That patch changes this to KERN_DEBUG.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add support for using f_uac1 function as a component of a gadget
composed with configfs.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When configfs support is added the values in question will have to be
used in two different places. Substitute them with defined constants
to avoid duplicating magic numbers.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Use the new usb_gstring_attach interface.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

There are no users of the old interface left, so it can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Use the new interface so that the old one can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Converting uac1 to the new function interface requires converting
the USB uac1's function code and its users.

This patch converts the f_uac1.c to the new function interface.

The file is now compiled into a separate usb_f_uac1.ko module.

The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Integrating configfs requires converting f_uac1 to new function interface,
which in turn requires converting it to the new function interface,
which involves separate compilation of f_uac1.c into usb_f_uac1.ko.
u_uac1.c contains some module parameters. After this patch is applied
they are still a part of the resulting g_audio.ko, but can be guarded
with a compatiblity flag which will be removed when no users of the old
function interface of f_uac1 are left.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

uac1 function is missing strings. Add them.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add support for using f_uac2 function as a component of a gadget
composed with configfs.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When configfs is integrated the same values will have to be used
as defaults. Use symbolic names in order not to duplicate magic numbers.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Use the new usb_gstring_attach interface.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

There are no users of the old interface left, so it can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Use the new interface so that the old one can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Converting uac2 to the new function interface requires converting
the USB uac2's function code and its users.

This patch converts the f_uac2.c to the new function interface.

The file is now compiled into a separate usb_f_uac2.ko module.

The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Eliminate static struct *agdev_g from f_uac2.c.
It is used for freeing its memory, but the same address can be found
by calling container_of in afunc_unbind(). This implies eliminating
uac2_unbind_config(). The audio_config_driver in audio.c does not have
its unbind method any more. It has been used only when uac2 is used,
so uac2 itself can handle unbinding in afunc_unbind().
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

that declaration is only used inside this driver,
marking it static.
Signed-off-by: Felipe Balbi <balbi@ti.com>

Remove unnecessary lines of register bit definitions in order
to enhance the readability. In this case, there are lines
per register offset definitions. There is no functional change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Pull x86 platform driver updates from Matthew Garrett:
 "A moderate number of changes, but nothing awfully significant.

  A lot of const cleanups, some reworking and additions to the rfkill
  quirks in the asus driver, a new driver for generating falling laptop
  events on Toshibas and some misc fixes.

  Maybe vendors have stopped inventing things"

* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (41 commits)
  platform/x86: Enable build support for toshiba_haps
  Documentation: Add file about toshiba_haps module
  platform/x86: Toshiba HDD Active Protection Sensor
  asus-nb-wmi: Add wapf4 quirk for the U32U
  alienware-wmi: make hdmi_mux enabled on case-by-case basis
  ideapad-laptop: Constify DMI table and other r/o variables
  asus-nb-wmi.c: Rename x401u quirk to wapf4
  compal-laptop: correct invalid hwmon name
  toshiba_acpi: Add Qosmio X75-A to the alt keymap dmi list
  toshiba_acpi: Add extra check to backlight code
  Fix log message about future removal of interface
  ideapad-laptop: Disable touchpad interface on Yoga models
  asus-nb-wmi: Add wapf4 quirk for the X550CC
  intel_ips: Make ips_mcp_limits variables static
  thinkpad_acpi: Mark volume_alsa_control_{vol,mute} as __initdata
  fujitsu-laptop: Mark fujitsu_dmi_table[] DMI table as __initconst
  hp-wmi: Add missing __init annotations to initialization code
  hp_accel: Constify ACPI and DMI tables
  fujitsu-tablet: Mark DMI callbacks as __init code
  dell-laptop: Mark dell_quirks[] DMI table as __initconst
  ...

Pull idle update from Len Brown:
 "Two Intel-platform-specific updates to intel_idle, and a cosmetic
  tweak to the turbostat utility"

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: tweak whitespace in output format
  intel_idle: Broadwell support
  intel_idle: Disable Baytrail Core and Module C6 auto-demotion

Pull module fix from Rusty Russell:
 "Nasty potential bug if someone uses a known module param with an
  invalid value (we don't fail unknown module params any more, just
  warn)"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  module: Clean up ro/nx after early module load failures

Pull virtio-rng update from Amit Shah:
 "Add derating factor for use by hwrng core

  Sending directly to you with the commit log changes Ted Ts'o pointed
  out.  Not sure if Rusty's back after his travel, but this already has
  his s-o-b"

* 'rng-queue' of git://git.kernel.org/pub/scm/linux/kernel/git/amit/virtio:
  virtio: rng: add derating factor for use by hwrng core

Pull btrfs updates from Chris Mason:
 "These are all fixes I'd like to get out to a broader audience.

  The biggest of the bunch is Mark's quota fix, which is also in the
  SUSE kernel, and makes our subvolume quotas dramatically more
  accurate.

  I've been running xfstests with these against your current git
  overnight, but I'm queueing up longer tests as well"

* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: disable strict file flushes for renames and truncates
  Btrfs: fix csum tree corruption, duplicate and outdated checksums
  Btrfs: Fix memory corruption by ulist_add_merge() on 32bit arch
  Btrfs: fix compressed write corruption on enospc
  btrfs: correctly handle return from ulist_add
  btrfs: qgroup: account shared subtrees during snapshot delete
  Btrfs: read lock extent buffer while walking backrefs
  Btrfs: __btrfs_mod_ref should always use no_quota
  btrfs: adjust statfs calculations according to raid profiles

Pull file locking bugfixes from Jeff Layton:
 "Most of these patches are to fix a long-standing regression that crept
  in when the BKL was removed from the file-locking code.  The code was
  converted to use a conventional spinlock, but some fl_release_private
  ops can block and you can end up sleeping inside the lock.

  There's also a patch to make /proc/locks show delegations as 'DELEG'"

* tag 'locks-v3.17-2' of git://git.samba.org/jlayton/linux:
  locks: update Locking documentation to clarify fl_release_private behavior
  locks: move locks_free_lock calls in do_fcntl_add_lease outside spinlock
  locks: defer freeing locks in locks_delete_lock until after i_lock has been dropped
  locks: don't reuse file_lock in __posix_lock_file
  locks: don't call locks_release_private from locks_copy_lock
  locks: show delegations as "DELEG" in /proc/locks

Pull aio updates from Ben LaHaise.

* git://git.kvack.org/~bcrl/aio-next:
  aio: use iovec array rather than the single one
  aio: fix some comments
  aio: use the macro rather than the inline magic number
  aio: remove the needless registration of ring file's private_data
  aio: remove no longer needed preempt_disable()
  aio: kill the misleading rcu read locks in ioctx_add_table() and kill_ioctx()
  aio: change exit_aio() to load mm->ioctx_table once and avoid rcu_read_lock()

Makefile and Kconfig build support patch for the newly introduced
kernel module toshiba_haps.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>

This patch provides information about the Toshiba HDD
Active Protection Sensor driver module toshiba_haps.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>