- 13 Jan, 2021 13 commits
-
-
Alex Elder authored
The IPA driver depends on some SMEM functionality (qcom_smem_init(), qcom_smem_alloc(), and qcom_smem_virt_to_phys()), but this is not reflected in the configuration dependencies. Add a dependency on QCOM_SMEM to avoid attempts to build the IPA driver without SMEM. This avoids a link error for certain configurations. Reported-by:
Randy Dunlap <rdunlap@infradead.org> Fixes: 38a4066f ("net: ipa: support COMPILE_TEST") Signed-off-by:
Alex Elder <elder@linaro.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20210112192134.493-1-elder@linaro.orgSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Maxim Kochetkov authored
Set proper value to IF_MODE register for MII mode. Signed-off-by:
Maxim Kochetkov <fido_max@inbox.ru> Link: https://lore.kernel.org/r/20210111043903.8044-1-fido_max@inbox.ruSigned-off-by:
-
Russell King authored
Add debugfs support to SFP so that the internal state of the SFP state machines and hardware signal state can be viewed from userspace, rather than having to compile a debug kernel to view state transitions in the kernel log. The 'state' output looks like: Module state: empty Module probe attempts: 0 0 Device state: up Main state: down Fault recovery remaining retries: 5 PHY probe remaining retries: 12 moddef0: 0 rx_los: 1 tx_fault: 1 tx_disable: 1 Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/E1kyYRe-0004kN-3F@rmk-PC.armlinux.org.ukSigned-off-by:
-
Jakub Kicinski authored
Long Li says: ==================== hv_netvsc: Prevent packet loss during VF add/remove This patch set fixes issues with packet loss on VF add/remove. ==================== Link: https://lore.kernel.org/r/1610153623-17500-1-git-send-email-longli@linuxonhyperv.comSigned-off-by:
-
Long Li authored
On VF hot remove, NETDEV_GOING_DOWN is sent to notify the VF is about to go down. At this time, the VF is still sending/receiving traffic and we request the VSP to switch datapath. On completion, the datapath is switched to synthetic and we can proceed with VF hot remove. Signed-off-by:
Long Li <longli@microsoft.com> Reviewed-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
-
Long Li authored
The completion indicates if NVSP_MSG4_TYPE_SWITCH_DATA_PATH has been processed by the VSP. The traffic is steered to VF or synthetic after we receive this completion. Signed-off-by:
kernel test robot <lkp@intel.com> Signed-off-by:
-
Long Li authored
The driver needs to check if the datapath has been switched to VF before sending traffic to VF. Signed-off-by:
-
Bhaskar Chowdhury authored
s/oen/one/ s/controling/controlling/ Signed-off-by:
Bhaskar Chowdhury <unixbhaskar@gmail.com> Acked-by:
-
Jakub Kicinski authored
Heiner Kallweit says: ==================== r8169: further improvements Series includes further smaller improvements. ==================== Link: https://lore.kernel.org/r/1bc3b7ef-b54a-d517-df54-27d61ca7ba94@gmail.comSigned-off-by:
-
Heiner Kallweit authored
Instead of doing the full DASH check each time r8168_check_dash() is called, let's do it once in probe and store DASH capabilities in a new rtl8169_private member. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
Saeed Mahameed <saeedm@nvidia.com> Signed-off-by:
-
Heiner Kallweit authored
Extend the mask to include the checksum failure bits. This allows to simplify the condition in rtl8169_rx_csum(). Signed-off-by:
-
Heiner Kallweit authored
At least from chip version 25 the vendor driver sets these rx flags for all chip versions if WOL is enabled. Therefore I wouldn't consider it a quirk, so let's rename the function. Signed-off-by:
-
Marek Vasut authored
The PHYLIB must be selected to provide mdiobus_*() functions, and the MICREL_PHY is necessary too, as that is the only possible PHY attached to the KS8851 (it is the internal PHY). Fixes: ef363122 ("net: ks8851: Register MDIO bus and the internal PHY") Signed-off-by:
Marek Vasut <marex@denx.de> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Lukas Wunner <lukas@wunner.de> Reviewed-by:
-
- 12 Jan, 2021 27 commits
-
-
Stefan Chulski authored
Patch didn't fix any issue, just improve parse flow and align ipv4 parse flow with ipv6 parse flow. Currently ipv4 kenguru parser first check IP protocol(TCP/UDP) and then destination IP address. Patch introduce reverse ipv4 parse, first destination IP address parsed and only then IP protocol. This would allow extend capability for packet L4 parsing and align ipv4 parsing flow with ipv6. Suggested-by:
Liron Himi <liron@marvell.com> Signed-off-by:
Stefan Chulski <stefanc@marvell.com> Link: https://lore.kernel.org/r/1610289059-14962-1-git-send-email-stefanc@marvell.comSigned-off-by:
-
Danilo Carvalho authored
List of things fixed: - Two of the socket options were idented with spaces instead of tabs. - Trailing whitespace in some lines. - Improper spacing around parenthesis caught by checkpatch.pl. - Mix of space and tabs in tcp_word_hdr union. Signed-off-by:
Danilo Carvalho <doak@google.com> Link: https://lore.kernel.org/r/20210108222104.2079472-1-doak@google.comSigned-off-by:
-
Jakub Kicinski authored
bareudp_dellink() only needs the device list to hand it to unregister_netdevice_queue(). We can pass NULL in, and unregister_netdevice_queue() will do the unregistering. There is no chance for batching on the error path, anyway. Suggested-by:
Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by:
-
Jakub Kicinski authored
Heiner Kallweit says: ==================== r8169: improve PLL power-down handling This series includes improvements to handling of PLL power-down. ==================== Link: https://lore.kernel.org/r/1608dfa3-c4a5-0e92-31f7-76674b3c173a@gmail.comSigned-off-by:
-
Heiner Kallweit authored
Clean up the remainings of rtl_pll_power_down/up and rename rtl_pll_power_down() to rtl_prepare_power_down(). Signed-off-by:
-
Heiner Kallweit authored
Realtek provided a description of bits 6 and 7 in register PMCH. They configure whether the chip powers down certain PLL in D3hot and D3cold respectively. They do not actually power down the PLL. Reflect this in the code and configure D3 PLL powerdown based on whether WOL is enabled. Signed-off-by:
-
Heiner Kallweit authored
There's no known reason why PLL powerdown on D3 shouldn't be enabled on chip versions 34, 35, 36, and 42. At least the vendor driver doesn't exclude any of these chip versions. Signed-off-by:
-
Heiner Kallweit authored
Instead of open-coding unaligned access let's use the predefined unaligned access helpers. Signed-off-by:
-
Jakub Kicinski authored
Heiner Kallweit says: ==================== r8169: improve jumbo configuration Small improvements to jumbo configuration. ==================== Link: https://lore.kernel.org/r/1dd337a0-ff5a-3fa0-91f5-45e86c0fce58@gmail.comSigned-off-by:
-
Heiner Kallweit authored
So far we don't increase the max read request size if we switch to jumbo mode before bringing up the interface for the first time. Let's change this. Signed-off-by:
-
Heiner Kallweit authored
Align behavior with r8168 vendor driver and don't reduce max read request size for RTL8168e in jumbo mode. Signed-off-by:
-
Florian Fainelli authored
The function was incorrectly named with a trailing 'r' at the end of prestera. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20210109050622.8081-1-f.fainelli@gmail.comSigned-off-by:
-
Russell King authored
Convert at803x_clk_out_config() to use phy_modify_mmd(). Signed-off-by:
-
Russell King authored
Extend the bitrate-derived support to include 2500BASE-X for modules that report a bitrate of 2500Mbaud. Signed-off-by:
-
Russell King authored
The SFP MSA defines two option bits in byte 65 to indicate how the Rx_LOS signal on SFP pin 8 behaves: bit 2 - Loss of Signal implemented, signal inverted from standard definition in SFP MSA (often called "Signal Detect"). bit 1 - Loss of Signal implemented, signal as defined in SFP MSA (often called "Rx_LOS"). Clearly, setting both bits results in a meaningless situation: it would mean that LOS is implemented in both the normal sense (1 = signal loss) and inverted sense (0 = signal loss). Unfortunately, there are modules out there which set both bits, which will be initially interpret as "inverted" sense, and then, if the LOS signal changes state, we will toggle between LINK_UP and WAIT_LOS states. Change our LOS handling to give well defined behaviour: only interpret these bits as meaningful if exactly one is set, otherwise treat it as if LOS is not implemented. Signed-off-by: -
Vladimir Oltean authored
The code that sets the DMA mask to 64 bits is bogus, it is taken from the enetc driver together with the rest of the PCI probing boilerplate. Since this patch is touching the error path to delete err_dma, let's also change the err_alloc_felix label which was incorrect. The kzalloc failure does not need a kfree, but it doesn't hurt either, since kfree works with NULL pointers. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
-
Jakub Kicinski authored
Vladimir Oltean says: ==================== Get rid of the switchdev transactional model Changes in v4: - Fixed build error in dsa_loop and build warning in hellcreek driver. - Scheduling the mlxsw SPAN work item regardless of the VLAN add return code, as per Ido's and Petr's request. Changes in v3: - Resolved a build warning in mv88e6xxx and tested that it actually works properly, which resulted in an extra patch (02/11). - Addressed Ido's minor feedback in commit 10/11 relating to a comment. Changes in v2: - Got rid of the vid_begin -> vid_end range too from the switchdev API. - Actually propagating errors from DSA MDB and VLAN notifiers. This series comes after the late realization that the prepare/commit separation imposed by switchdev does not help literally anybody: https://patchwork.kernel.org/project/netdevbpf/patch/20201212203901.351331-1-vladimir.oltean@nxp.com/ We should kill it before it inflicts even more damage to the error handling logic in drivers. Also remove the unused VLAN ranges feature from the switchdev VLAN objects, which simplifies all drivers by quite a bit. ==================== Link: https://lore.kernel.org/r/20210109000156.1246735-1-olteanv@gmail.comSigned-off-by:
-
Vladimir Oltean authored
Now that all users of struct switchdev_trans have been modified to do without it, we can remove this structure and the two helpers to determine the phase. Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Acked-by:
Linus Walleij <linus.walleij@linaro.org> Acked-by:
Jiri Pirko <jiri@nvidia.com> Signed-off-by:
-
Vladimir Oltean authored
As of commit 457e20d6 ("mlxsw: spectrum_switchdev: Avoid returning errors in commit phase"), the mlxsw driver performs the VLAN object offloading during the prepare phase. So conversion just seems to be a matter of removing the code that was running in the commit phase. Ido Schimmel explains that the reason why mlxsw_sp_span_respin is called unconditionally is because the bridge driver will ignore -EOPNOTSUPP and actually add the VLAN on the bridge device - see commit 9c86ce2c ("net: bridge: Notify about bridge VLANs") and commit ea472175 ("mlxsw: spectrum_switchdev: Ignore bridge VLAN events"). Since the VLAN was successfully added on the bridge device, mlxsw_sp_span_respin_work() should be able to resolve the egress port for a packet that is mirrored to a gre tap and passes through the bridge device. Therefore keep the logic as it is. Signed-off-by:
-
Vladimir Oltean authored
Now that all port object notifiers were converted to be non-transactional, we can remove the comments that say otherwise. Signed-off-by:
-
Vladimir Oltean authored
It should be the driver's business to logically separate its VLAN offloading into a preparation and a commit phase, and some drivers don't need / can't do this. So remove the transactional shim from DSA and let drivers propagate errors directly from the .port_vlan_add callback. It would appear that the code has worse error handling now than it had before. DSA is the only in-kernel user of switchdev that offloads one switchdev object to more than one port: for every VLAN object offloaded to a user port, that VLAN is also offloaded to the CPU port. So the "prepare for user port -> check for errors -> prepare for CPU port -> check for errors -> commit for user port -> commit for CPU port" sequence appears to make more sense than the one we are using now: "offload to user port -> check for errors -> offload to CPU port -> check for errors", but it is really a compromise. In the new way, we can catch errors from the commit phase that we previously had to ignore. But we have our hands tied and cannot do any rollback now: if we add a VLAN on the CPU port and it fails, we can't do the rollback by simply deleting it from the user port, because the switchdev API is not so nice with us: it could have simply been there already, even with the same flags. So we don't even attempt to rollback anything on addition error, just leave whatever VLANs managed to get offloaded right where they are. This should not be a problem at all in practice. Signed-off-by:
-
Vladimir Oltean authored
For many drivers, the .port_mdb_prepare callback was not a good opportunity to avoid any error condition, and they would suppress errors found during the actual commit phase. Where a logical separation between the prepare and the commit phase existed, the function that used to implement the .port_mdb_prepare callback still exists, but now it is called directly from .port_mdb_add, which was modified to return an int code. Signed-off-by:
-
Vladimir Oltean authored
Remove the shim introduced in DSA for offloading the bridge ageing time from switchdev, by first checking whether the ageing time is within the range limits requested by the driver. Signed-off-by:
-
Vladimir Oltean authored
Since the introduction of the switchdev API, port attributes were transmitted to drivers for offloading using a two-step transactional model, with a prepare phase that was supposed to catch all errors, and a commit phase that was supposed to never fail. Some classes of failures can never be avoided, like hardware access, or memory allocation. In the latter case, merely attempting to move the memory allocation to the preparation phase makes it impossible to avoid memory leaks, since commit 91cf8ece ("switchdev: Remove unused transaction item queue") which has removed the unused mechanism of passing on the allocated memory between one phase and another. It is time we admit that separating the preparation from the commit phase is something that is best left for the driver to decide, and not something that should be baked into the API, especially since there are no switchdev callers that depend on this. This patch removes the struct switchdev_trans member from switchdev port attribute notifier structures, and converts drivers to not look at this member. In part, this patch contains a revert of my previous commit 2e554a7a ("net: dsa: propagate switchdev vlan_filtering prepare phase to drivers"). For the most part, the conversion was trivial except for: - Rocker's world implementation based on Broadcom OF-DPA had an odd implementation of ofdpa_port_attr_bridge_flags_set. The conversion was done mechanically, by pasting the implementation twice, then only keeping the code that would get executed during prepare phase on top, then only keeping the code that gets executed during the commit phase on bottom, then simplifying the resulting code until this was obtained. - DSA's offloading of STP state, bridge flags, VLAN filtering and multicast router could be converted right away. But the ageing time could not, so a shim was introduced and this was left for a further commit. Signed-off-by:
-
Vladimir Oltean authored
After the removal of the transactional model inside switchdev_port_obj_add_now, it has no added value and we can just call switchdev_port_obj_notify directly, bypassing this function. Let's delete it. Signed-off-by:
-
Vladimir Oltean authored
Since the introduction of the switchdev API, port objects were transmitted to drivers for offloading using a two-step transactional model, with a prepare phase that was supposed to catch all errors, and a commit phase that was supposed to never fail. Some classes of failures can never be avoided, like hardware access, or memory allocation. In the latter case, merely attempting to move the memory allocation to the preparation phase makes it impossible to avoid memory leaks, since commit 91cf8ece ("switchdev: Remove unused transaction item queue") which has removed the unused mechanism of passing on the allocated memory between one phase and another. It is time we admit that separating the preparation from the commit phase is something that is best left for the driver to decide, and not something that should be baked into the API, especially since there are no switchdev callers that depend on this. This patch removes the struct switchdev_trans member from switchdev port object notifier structures, and converts drivers to not look at this member. Where driver conversion is trivial (like in the case of the Marvell Prestera driver, NXP DPAA2 switch, TI CPSW, and Rocker drivers), it is done in this patch. Where driver conversion needs more attention (DSA, Mellanox Spectrum), the conversion is left for subsequent patches and here we only fake the prepare/commit phases at a lower level, just not in the switchdev notifier itself. Where the code has a natural structure that is best left alone as a preparation and a commit phase (as in the case of the Ocelot switch), that structure is left in place, just made to not depend upon the switchdev transactional model. Signed-off-by:
-
Vladimir Oltean authored
mv88e6xxx apparently has a problem offloading VID 0, which the 8021q module tries to install as part of commit ad1afb00 ("vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)"). That mv88e6xxx restriction seems to have been introduced by the "VTU GetNext VID-1 trick to retrieve a single entry" - see commit 2fb5ef09 ("net: dsa: mv88e6xxx: extract single VLAN retrieval"). There is one more problem. The mv88e6xxx CPU port and DSA links do not report properly in the prepare phase what are the VLANs that they can offload. They'll say they can offload everything: mv88e6xxx_port_vlan_prepare -> mv88e6xxx_port_check_hw_vlan: /* DSA and CPU ports have to be members of multiple vlans */ if (dsa_is_dsa_port(ds, port) || dsa_is_cpu_port(ds, port)) return 0; Except that if you actually try to commit to it, they'll error out and print this message: [ 32.802438] mv88e6085 d0032004.mdio-mii:12: p9: failed to add VLAN 0t which comes from: mv88e6xxx_port_vlan_add -> mv88e6xxx_port_vlan_join: if (!vid) return -EOPNOTSUPP; What prevents this condition from triggering in real life? The fact that when a DSA_NOTIFIER_VLAN_ADD is emitted, it never targets a DSA link directly. Instead, the notifier will always target either a user port or a CPU port. DSA links just happen to get dragged in by: static bool dsa_switch_vlan_match(struct dsa_switch *ds, int port, struct dsa_notifier_vlan_info *info) { ... if (dsa_is_dsa_port(ds, port)) return true; ... } So for every DSA VLAN notifier, during the prepare phase, it will just so happen that there will be somebody to say "no, don't do that". This will become a problem when the switchdev prepare/commit transactional model goes away. Every port needs to think on its own. DSA links can no longer bluff and rely on the fact that the prepare phase will not go through to the end, because there will be no prepare phase any longer. Fix this issue before it becomes a problem, by having the "vid == 0" check earlier than the check whether we are a CPU port / DSA link or not. Also, the "vid == 0" check becomes unnecessary in the .port_vlan_add callback, so we can remove it. Signed-off-by:
-
