Both aggr_time_limit_encode() and hol_block_timer_encode() figure
out how to encode a millisecond time value so it can be programmed
into a register.  Rearranging them a bit can make their similarity
more obvious, with both taking essentially the same form.

To do this:
  - Return 0 immediately in aggr_time_limit_encode() if the
    microseconds value supplied is zero.
  - Reverse the test at top of aggr_time_limit_encode(), so we
    compute and return the Qtime value in the "true" block,
    and compute the result the old way otherwise.
  - Open-code (and eliminate) hol_block_timer_qtime_encode() at the
    top of hol_block_timer_encode() in the case we use Qtimer.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Create a new function ipa_qtime_val() which returns a value that
indicates what should be encoded for a register with a time field
expressed using Qtime.  Use it to factor out common code in
aggr_time_limit_encoded() and hol_block_timer_qtime_val().

Rename aggr_time_limit_encoded() and hol_block_timer_qtime_val() so
their names are both verbs ending in "encode".  Rename the "limit"
argument to the former to be "milliseconds" for consistency.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In two spots we use u32_replace_bits() to replace a set of bits in a
register while preserving the rest.  Both of those cases just zero
the bits being replaced, and this can be done more simply without
using that function.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'linux-can-next-for-6.1-20220923' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2022-09-23

The first 2 patches are by Ziyang Xuan and optimize registration and
the sending in the CAN BCM protocol a bit.

The next 8 patches target the gs_usb driver. 7 are by me and first fix
the time hardware stamping support (added during this net-next cycle),
rename a variable, convert the usb_control_msg + manual
kmalloc()/kfree() to usb_control_msg_{send,rev}(), clean up the error
handling and add switchable termination support. The patch by Rhett
Aultman and Vasanth Sadhasivan convert the driver from
usb_alloc_coherent()/usb_free_coherent() to kmalloc()/URB_FREE_BUFFER.

The last patch is by Shang XiaoJing and removes an unneeded call to
dev_err() from the ctucanfd driver.

* tag 'linux-can-next-for-6.1-20220923' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
  can: ctucanfd: Remove redundant dev_err call
  can: gs_usb: remove dma allocations
  can: gs_usb: add switchable termination support
  can: gs_usb: gs_make_candev(): clean up error handling
  can: gs_usb: convert from usb_control_msg() to usb_control_msg_{send,recv}()
  can: gs_usb: gs_cmd_reset(): rename variable holding struct gs_can pointer to dev
  can: gs_usb: gs_can_open(): initialize time counter before starting device
  can: gs_usb: add missing lock to protect struct timecounter::cycle_last
  can: gs_usb: gs_usb_get_timestamp(): fix endpoint parameter for usb_control_msg_recv()
  can: bcm: check the result of can_send() in bcm_can_tx()
  can: bcm: registration process optimization in bcm_module_init()
====================

Link: https://lore.kernel.org/r/20220923120859.740577-1-mkl@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Antoine Tenart says:

====================
net: macsec: remove the preparation phase when offloading operations

It was reported[1] the 2-step phase offloading of MACsec operations did
not fit well and device drivers were mostly ignoring the first phase
(preparation). In addition the s/w fallback in case h/w rejected an
operation, which could have taken advantage of this design, never was
implemented and it's probably not a good idea anyway (at least
unconditionnally). So let's remove this logic which only makes the code
more complex for no advantage, before there are too many drivers
providing MACsec offloading.

This series removes the first phase (preparation) of the MACsec h/w
offloading. The modifications are split per-driver and in a way that
makes bissection working with logical steps; but I can squash some
patches if needed.

This was tested on the MSCC PHY but not on the Altantic nor mlx5e NICs.

[1] https://lore.kernel.org/all/166322893264.61080.12133865599607623050@kwain/T/
====================

Link: https://lore.kernel.org/r/20220921135118.968595-1-atenart@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Now that the MACsec offloading preparation phase was removed from the
MACsec core implementation as well as from drivers implementing it, we
can safely remove the flag representing it.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Remove checks on the prepare phase as it is now unused by the MACsec
core implementation.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Remove checks on the prepare phase as it is now unused by the MACsec
core implementation.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Remove checks on the prepare phase as it is now unused by the MACsec
core implementation.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The hardware offloading in MACsec was initially supported using 2 phases.
This was proposed in the RFC as this could have allowed easier fallback
to the software implementation if the hardware did not support a feature
or had enough entries already. But this fallback wasn't implemented and
might not be a good idea after all. In addition it turned out this logic
didn't mapped well the hardware logic and device drivers were mostly
ignoring the preparation phase.

Let's remove this as it does not offer any advantage and is ignored by
drivers.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation for removing the MACsec h/w offloading preparation phase,
make it a no-op in the Atlantic driver.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation for removing the MACsec h/w offloading preparation phase,
make it a no-op in the MSCC phy driver.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

It looks like this test has been accidentally dropped when resolving
conflicts in this Makefile.

Most probably because there were 3 different patches modifying this file
in parallel:

  commit 152e8ec7 ("selftests/bonding: add a test for bonding lladdr target")
  commit bbb774d9 ("net: Add tests for bonding and team address list management")
  commit 2ffd5732 ("selftests: bonding: cause oops in bond_rr_gen_slave_id")

The first one was applied in 'net-next' while the two other ones were
recently applied in the 'net' tree.

But that's alright, easy to fix by re-adding the missing one!

Fixes: 0140a716 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Link: https://lore.kernel.org/r/20220923082306.2468081-1-matthieu.baerts@tessares.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

devm_ioremap_resource() prints error message in itself. Remove the
dev_err call to avoid redundant error message.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Link: https://lore.kernel.org/all/20220923095835.14647-1-shangxiaojing@huawei.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

DMA allocated buffers are a precious resource. If there is no need for
DMA allocations, then it might be worth to use non-dma allocated
buffers.

After testing the gs_usb driver with and without DMA allocation, there
does not seem to be a significant change in latency or CPU utilization
either way. Therefore, DMA allocation is not necessary and removed.

Internal buffers used within urbs were managed and freed manually.
These buffers are no longer needed to be managed by the driver. The
URB_FREE_BUFFER flag, allows for the buffers in question to be
automatically freed.
Co-developed-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Vasanth Sadhasivan <vasanth.sadhasivan@samsara.com>
Link: https://lore.kernel.org/all/20220920154724.861093-2-rhett.aultman@samsara.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The candleLight community is working on switchable termination support
for the candleLight firmware. As the the Linux CAN framework supports
switchable termination add this feature to the gs_usb driver.

Devices supporting the feature should set the
GS_CAN_FEATURE_TERMINATION and implement the
GS_USB_BREQ_SET_TERMINATION and GS_USB_BREQ_GET_TERMINATION control
messages.

For now the driver assumes for activated termination the standard
termination value of 120Ω.

Link: https://lore.kernel.org/all/20220923074114.662045-1-mkl@pengutronix.de
Link: https://github.com/candle-usb/candleLight_fw/issues/92
Link: https://github.com/candle-usb/candleLight_fw/pull/109
Link: https://github.com/candle-usb/candleLight_fw/pull/108
Cc: Daniel Trevitz <daniel.trevitz@wika.com>
Cc: Ryan Edwards <ryan.edwards@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Introduce a label to free the allocated candev in case of an error and
make use of if. Fix a memory leak if the extended bit timing cannot be
read. Extend the error messages to print the number of the failing
channel and the symbolic error name.

Link: https://lore.kernel.org/all/20220921193902.575416-4-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Convert the driver to use usb_control_msg_{send,recv}() instead of
usb_control_msg(). These functions allow the data to be placed on the
stack. This makes the driver a lot easier as we don't have to deal
with dynamically allocated memory.

Link: https://lore.kernel.org/all/20220921193902.575416-3-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Most of the driver uses the variable "dev" to point to the struct
gs_can. Use the same name in gs_cmd_reset(), too. Rename gsdev to dev.

Fixes: d08e973a ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220921193902.575416-2-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

On busy networks the CAN controller might receive CAN frames directly
after starting it but before the timecounter is setup. This will lead
to NULL pointer deref while converting the converting the CAN frame's
timestamp with the timecounter.

Close the race window by setting up the timecounter before starting
the CAN controller.

Fixes: 45dfa45f ("can: gs_usb: add RX and TX hardware timestamp support")
Link: https://lore.kernel.org/all/20220921081329.385509-1-mkl@pengutronix.de
Cc: John Whittington <git@jbrengineering.co.uk
Tested-by: John Whittington <git@jbrengineering.co.uk>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The struct timecounter::cycle_last is a 64 bit variable, read by
timecounter_cyc2time(), and written by timecounter_read(). On 32 bit
architectures this is not atomic.

Add a spinlock to protect access to struct timecounter::cycle_last. In
the gs_usb_timestamp_read() callback the lock is dropped to execute a
sleeping synchronous USB transfer. This is safe, as the variable we
want to protect is accessed during this call.

Fixes: 45dfa45f ("can: gs_usb: add RX and TX hardware timestamp support")
Link: https://lore.kernel.org/all/20220920100416.959226-3-mkl@pengutronix.de
Cc: John Whittington <git@jbrengineering.co.uk>
Tested-by: John Whittington <git@jbrengineering.co.uk>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The 2nd argument of usb_control_msg_recv() is the "endpoint",
usb_control_msg_recv() will internally convert the endpoint into a
pipe with usb_rcvctrlpipe().

In gs_usb_get_timestamp() not the endpoint "0" is passed, but the
pipe. This worked by accident as endpoint is a __u8 and the lowest 8
bits of the pipe are 0. Fix this copy/paste error by using the correct
endpoint of "0".

Fixes: 45dfa45f ("can: gs_usb: add RX and TX hardware timestamp support")
Link: https://lore.kernel.org/all/20220920100416.959226-2-mkl@pengutronix.de
Cc: John Whittington <git@jbrengineering.co.uk>
Tested-by: John Whittington <git@jbrengineering.co.uk>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Ziyang Xuan <william.xuanziyang@huawei.com> says:

Do some small optimization for can_bcm.

v1: https://lore.kernel.org/all/cover.1662606045.git.william.xuanziyang@huawei.com

Link: https://lore.kernel.org/all/cover.1663206163.git.william.xuanziyang@huawei.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

If can_send() fail, it should not update frames_abs counter
in bcm_can_tx(). Add the result check for can_send() in bcm_can_tx().
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Suggested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/all/9851878e74d6d37aee2f1ee76d68361a46f89458.1663206163.git.william.xuanziyang@huawei.comAcked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Now, register_netdevice_notifier() and register_pernet_subsys() are both
after can_proto_register(). It can create CAN_BCM socket and process socket
once can_proto_register() successfully, so it is possible missing notifier
event or proc node creation because notifier or bcm proc directory is not
registered or created yet. Although this is a low probability scenario, it
is not impossible.

Move register_pernet_subsys() and register_netdevice_notifier() to the
front of can_proto_register(). In addition, register_pernet_subsys() and
register_netdevice_notifier() may fail, check their results are necessary.
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/all/823cff0ebec33fa9389eeaf8b8ded3217c32cb38.1663206163.git.william.xuanziyang@huawei.comAcked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Horatiu Vultur says:

====================
net: lan966x: Add mqprio and taprio support

Add support for offloading QoS features with tc command to lan966x. The
offloaded QoS features are mqprio and taprio.

v1->v2:
- fix compilation warning
- rename lan966x_taprio_enable/disable to lan966x_taprio_add/del
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Lan966x switch supports time-based egress shaping in hardware
according to IEEE 802.1Qbv. Add support for TAS configuration on
egress port of lan966x switch.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add registers that are used by taprio to configure the HW.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement mqprio qdisc support using tc command.
The HW supports 8 priority queues from highest (7) to lowest (0).
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a define for the number of priority queues on lan966x. Because there
will be more checks for this, so instead of using hardcoded value all
over the place add a define for this.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use kstrdup instead of open-coding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Read link status from SGMII PCS for in-band managed 2500Base-X and
1000Base-X connection on a MAC port of the MT7531. This is needed to
get the SFP cage working which is connected to SGMII interface of
port 5 of the MT7531 switch IC on the Bananapi BPi-R3 board.
While at it also handle an_complete for both the autoneg and the
non-autoneg codepath.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sean Anderson says:

====================
net: phy: Add support for rate matching

This adds support for phy rate matching: when a phy adapts between
differing phy interface and link speeds. It was originally submitted as
part of [1], which is considered "v1" of this series.

Several past discussions [2-4] around adding rate adaptation provide
some context.

Although in earlier versions of this series, userspace could disable
rate matching, now it is only possible to determine the current rate
adaptation type. Disabling or otherwise configuring rate adaptation has
been left for future work. However, because currently only
RATE_MATCH_PAUSE is implemented, it is possible to disable rate
adaptation by modifying the advertisement appropriately.

[1] https://lore.kernel.org/netdev/20220715215954.1449214-1-sean.anderson@seco.com/T/#t
[2] https://lore.kernel.org/netdev/1579701573-6609-1-git-send-email-madalin.bucur@oss.nxp.com/
[3] https://lore.kernel.org/netdev/1580137671-22081-1-git-send-email-madalin.bucur@oss.nxp.com/
[4] https://lore.kernel.org/netdev/20200116181933.32765-1-olteanv@gmail.com/

Changes in v6:
- Don't announce that we've enabled pause frames for rate adaptation
- Merry Christmas
- Rename rate adaptation to rate matching
- Reword documentation, (hopefully) taking into account feedback

Changes in v5:
- Break off patch "net: phy: Add 1000BASE-KX interface mode" for
  separate submission.
- Document phy_rate_adaptation_to_str
- Drop patch "Add some helpers for working with mac caps"; it has been
  incorperated into the autonegotiation patch.
- Move phylink_cap_from_speed_duplex to this commit
- Rebase onto net-next/master
- Remove unnecessary comma

Changes in v4:
- Export phy_rate_adaptation_to_str
- Remove phylink_interface_max_speed, which was accidentally added
- Split off the LS1046ARDB 1G fix

Changes in v3:
- Add phylink_cap_from_speed_duplex to look up the mac capability
  corresponding to the interface's speed.
- Document MAC_(A)SYM_PAUSE
- Include RATE_ADAPT_CRS; it's a few lines and it doesn't hurt.
- Modify link settings directly in phylink_link_up, instead of doing
  things more indirectly via link_*.
- Move unused defines to next commit (where they will be used)
- Remove "Support differing link/interface speed/duplex". It has been
  rendered unnecessary due to simplification of the rate adaptation
  patches. Thanks Russell!
- Rewrite cover letter to better reflect the opinions of the developers
  involved

Changes in v2:
- Add (read-only) ethtool support for rate adaptation
- Add comments clarifying the register defines
- Add locking to phy_get_rate_adaptation
- Always use the rate adaptation setting to determine the interface
  speed/duplex (instead of sometimes using the interface mode).
- Determine the interface speed and max mac speed directly instead of
  guessing based on the caps.
- Move part of commit message to cover letter, as it gives a good
  overview of the whole series, and allows this patch to focus more on
  the specifics.
- Reorder variables in aqr107_read_rate
- Use int/defines instead of enum to allow for use in ioctls/netlink
- Use the phy's rate adaptation setting to determine whether to use its
  link speed/duplex or the MAC's speed/duplex with MLO_AN_INBAND.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for rate matching for phys similar to the AQR107. We
assume that all phys using aqr107_read_status support rate matching.
However, it could be possible to determine support based on the firmware
revision if there are phys discovered which do not support rate
matching.  However, as rate matching is advertised in the datasheets for
these phys, I suspect it is supported most boards.

Despite the name, the "config" registers are updated with the current
rate matching method (if any). Because they appear to be updated
automatically, I don't know if these registers can be used to disable
rate matching.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These are documented in the AQR115 register reference. I haven't tested
them, but perhaps they'll be useful to someone.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for adjusting the advertisement for pause-based rate
matching. This may result in a lossy link, since the final link settings
are not adjusted. Asymmetric pause support is necessary. It would be
possible for a MAC supporting only symmetric pause to use pause-based rate
adaptation, but only if pause reception was enabled as well.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the phy is configured to use pause-based rate matching, ensure that
the link is full duplex with pause frame reception enabled. As
suggested, if pause-based rate matching is enabled by the phy, then
pause reception is unconditionally enabled.

The interface duplex is determined based on the rate matching type.
When rate matching is enabled, so is the speed. We assume the maximum
interface speed is used. This is only relevant for MLO_AN_PHY. For
MLO_AN_INBAND, the MAC/PCS's view of the interface speed will be used.

Although there are no RATE_ADAPT_CRS phys in-tree, it has been added for
comparison (and the implementation is quite simple).
Co-developed-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for rate matching (also known as rate adaptation) to
the phy subsystem. The general idea is that the phy interface runs at
one speed, and the MAC throttles the rate at which it sends packets to
the link speed. There's a good overview of several techniques for
achieving this at [1]. This patch adds support for three: pause-frame
based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and
2BASE-TL), and open-loop-based (such as in 10GBASE-W).

This patch makes a few assumptions and a few non assumptions about the
types of rate matching available. First, it assumes that different phys
may use different forms of rate matching. Second, it assumes that phys
can use rate matching for any of their supported link speeds (e.g. if a
phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T).
Third, it does not assume that all interface modes will use the same
form of rate matching. Fourth, it does not assume that all phy devices
will support rate matching (even if some do). Relaxing or strengthening
these (non-)assumptions could result in a different API. For example, if
all interface modes were assumed to use the same form of rate matching,
then a bitmask of interface modes supportting rate matching would
suffice.

For some better visibility into the process, the current rate matching
mode is exposed as part of the ethtool ksettings. For the moment, only
read access is supported. I'm not sure what userspace might want to
configure yet (disable it altogether, disable just one mode, specify the
mode to use, etc.). For the moment, since only pause-based rate
adaptation support is added in the next few commits, rate matching can
be disabled altogether by adjusting the advertisement.

802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and
"rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls
this feature "rate adaptation". I chose "rate matching" because it is
shorter, and because Russell doesn't think "adaptation" is correct in this
context.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we call phylink_caps_to_linkmodes directly from
phylink_get_linkmodes, it is difficult to re-use this functionality in
MAC drivers. This is because MAC drivers must then work with an ethtool
linkmode bitmap, instead of with mac capabilities. Instead, let the
caller of phylink_get_linkmodes do the conversion. To reflect this
change, rename the function to phylink_get_capabilities.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is convenient for MAC drivers. They can use it to add or
remove particular link modes based on capabilities (such as if half
duplex is not supported for a particular interface mode).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>