Make the case labels the same indent as the switch.

(git diff -w net/appletalk shows no difference)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a change sequence counter to each net namespace
which is bumped whenever a netdevice is added or removed from
the list. If such a change occurred while a link dump took place,
the dump will have the NLM_F_DUMP_INTR flag set in the first
message which has been interrupted and in all subsequent messages
of the same dump.

Note that links may still be modified or renamed while a dump is
taking place but we can guarantee for userspace to receive a
complete list of links and not miss any.

Testing:
I have added 500 VLAN netdevices to make sure the dump is split
over multiple messages. Then while continuously dumping links in
one process I also continuously deleted and re-added a dummy
netdevice in another process. Multiple dumps per seconds have
had the NLM_F_DUMP_INTR flag set.

I guess we can wait for Johannes patch to hit net-next via the
wireless tree.  I just wanted to give this some testing right away.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to check for the address being a multicast address in
the netdev_for_each_mc_addr loop, so remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

It may be set in the card while the driver is probed by kdump kernel after a
crash.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On some skews, the BE card sends pause frames (and not drop pkts) if there are
no more posted buffers available for packet reception.  This behaviour has a
side effect: When an interface is disabled, buffers are no longer posted on the
corresponding RX rings. All broadcast and multicast traffic being received on
the port will quickly fill up the PMEM and cause pause push back. As the PMEM
is shared by both the ports, all traffic being received on the other (enabled)
port also gets stalled.
The fix is to destroy RX rings when the interface is disabled. If there is no
RX ring match in the RXF lookup, the packets are discarded and so don't hog the
PMEM.
The RXQ creation cmd must now use MCC instead of MBOX as they are are called
post MCC queue creation.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some (older)versions of cards/fw may not recognize certain cmds and
return illegal/unsupported errors. As long as the driver can handle
this gracefully there is no need to log an error msg.
Also finetuned 2 existing error log messages.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Add external loopback test in self test:
  - Send set external loopback mode request to fw.
     To quiscent other storage functions.
  - Perform test
  - Send unset loopback mode request to fw.

o Rename ilb to lb.
o Update driver version 5.0.20.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

External loopback test can be performed by application without any driver
support on normal Ethernet cards.
But on CNA devices, where multiple functions share same physical port.
Here internal loopback test and external loopback test can be initiated by
multiple functions at same time. To co exist all functions, firmware need
to regulate what test can be run by which function. So before performing external
loopback test, command need to send to firmware, which will quiescent other functions.

User may not want to run external loopback test always. As special cable need to be
connected for this test.
So adding explicit flag in ethtool self test, which will specify interface
to perform external loopback test.
 ETH_TEST_FL_EXTERNAL_LB: Application set to request external loopback test
 ETH_TEST_FL_EXTERNAL_LB_DONE: Driver ack if test performed
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to check for the address being a multicast address in
the netdev_for_each_mc_addr loop, so remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to check for the address being a multicast address in
the netdev_for_each_mc_addr loop, so remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to check for the address being a multicast address in
the netdev_for_each_mc_addr loop, so remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to check for the address being a multicast address in
the netdev_for_each_mc_addr loop, so remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is error path calls unlock_irq() where we haven't disabled the
IRQs.  The comment says that this error path can never happen.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Exclude duplicated checking for iface-up. This flags is checked in 'is_skb_forwardable' function, which is subroutine of 'dev_forward_skb'.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

	1. Using enum name instead of numeric value.
	2. device_set_wakeup_enable expect bool argument
	   adding !!() to the argument to be passed.
	3. Remove non-jme-hardware related operations from
	   jme_clear_pm()
	4. Reuse jme_clear_pm() in jme_resume() and jme_powersave_phy()
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS is using SET_SYSTEM_SLEEP_PM_OPS
and SET_SYSTEM_SLEEP_PM_OPS is empty when CONFIG_PM_SLEEP
is not defined.

Switching #ifdef CONFIG_PM to #ifdef CONFIG_PM_SLEEP
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's no need for "default N' (or 'default n') as it's default.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic driver and the underlying hardware use different units for representing the interrupt coalesce timer.
Driver converts the interrupt coalesce timer in usec to hardware cycles while setting the relevant hardware
registers. The conversion factor can be different for each of the adapter hardware types. So it is dynamically
learnt from the adapter firmware using the devcmd CMD_INTR_COAL_CONVERT. This allows the driver to configure
the hardware interrupt coalesce timers in a platform independent way.
Signed-off-by: Danny Guo <dannguo@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>

Use per-cpu variables to maintain 64 bit statistics.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>

Add xen-backend:vif module alias to the xen-netback module. This allows
automatic loading of the module.
Signed-off-by: Bastian Blank <waldi@debian.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Update MAINTAINERS to refelect new people working on myri10ge
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update version and copyright
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Miscellaneous white space, style, and other cleanups

v2 includes corrections from Joe Perches
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PCIE capability offset is saved during PCI bus walking.  It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add myri10ge driver support for the ethtool identify operation.
NOTE: Rather than blinking (which is the normal case), when identify is
used, the yellow LED turns solid.
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow page-based receive to work when small_bytes is set to 0.
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clean up watchdog reset code:
 - move code that checks for stuck slice to a common routine
 - unless there is a confirmed h/w fault, verify that a stuck
   slice is still stuck in the watchdog worker; if the slice is no
   longer stuck, abort the reset.
 - this removes an egregious 2000ms pause in the watchdog worker that
   was a diagnostic aid (to look for spurious resets) the snuck into
   production code.

v3 includes corrections from Joe Perches
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A SRAM parity error can cause a surprise link down.  Since We can
recover from SRAM parity errors, mask PCI surprise down events.
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ensure that our tx queues remain stopped when we stop them in
myri10ge_close().  Not doing so can potentially lead to traffic being
transmitted when the interface is removed, which can lead to NULL
pointer dereferences.
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch enables the 6131 family of chips to forward DSA
packets to other switch chips.  This is needed if multiple
DSA chips are used in a device.  Without this patch the
chip will drop any DSA packets not destined for it.

This patch only enables the forwarding of DSA packets if
multiple chips are used in the switch configuration.
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just spelling fixes.

Actually, a twofer with vaiables/variables as well.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fixes thses build errors:

drivers/net/ll_temac_main.c: In function 'temac_dma_bd_release':
drivers/net/ll_temac_main.c:209:4: error: implicit declaration of function 'dma_unmap_single'
drivers/net/ll_temac_main.c:215:3: error: implicit declaration of function 'dma_free_coherent'
drivers/net/ll_temac_main.c: In function 'temac_dma_bd_init':
drivers/net/ll_temac_main.c:243:2: error: implicit declaration of function 'dma_alloc_coherent'
drivers/net/ll_temac_main.c:243:14: warning: assignment makes pointer from integer without a cast
drivers/net/ll_temac_main.c:251:14: warning: assignment makes pointer from integer without a cast
drivers/net/ll_temac_main.c:280:3: error: implicit declaration of function 'dma_map_single'
drivers/net/ll_temac_main.c: In function 'temac_start_xmit_done':
drivers/net/ll_temac_main.c:628:22: warning: cast to pointer from integer of different size

Caused by commit commit b7f080cf ("net: remove mm.h inclusion from
netdevice.h").
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

fixes these build errors:

drivers/net/can/sja1000/sja1000_of_platform.c: In function 'sja1000_ofp_read_reg':
drivers/net/can/sja1000/sja1000_of_platform.c:61:2: error: implicit declaration of function 'in_8'
drivers/net/can/sja1000/sja1000_of_platform.c: In function 'sja1000_ofp_write_reg':
drivers/net/can/sja1000/sja1000_of_platform.c:67:2: error: implicit declaration of function 'out_8'
drivers/net/can/sja1000/sja1000_of_platform.c: In function 'sja1000_ofp_remove':
drivers/net/can/sja1000/sja1000_of_platform.c:81:2: error: implicit declaration of function 'iounmap'
drivers/net/can/sja1000/sja1000_of_platform.c: In function 'sja1000_ofp_probe':
drivers/net/can/sja1000/sja1000_of_platform.c:113:2: error: implicit declaration of function 'ioremap_nocache'
drivers/net/can/sja1000/sja1000_of_platform.c:113:7: warning: assignment makes pointer from integer without a cast

Caused by commit b7f080cf ("net: remove mm.h inclusion from
netdevice.h").
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

When receiving packets from another guest on the same hypervisor, it's
generally possible to receive large packets because no segmentation is
necessary and these packets are handled by LRO.  However, when doing
routing or bridging we must disable LRO and lose this benefit.  In
these cases GRO can still be used and it is very effective because the
packets which are segmented in the hypervisor are received very close
together and can easily be merged.

CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: Scott Goldman <scottjg@vmware.com>
CC: VMware PV-Drivers <pv-drivers@vmware.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Scott J. Goldman <scottjg@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PCIE capability offset is saved during PCI bus walking.  It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PCIE capability offset is saved during PCI bus walking.  It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.  Also, pci_is_pcie is a
better way of determining if the device is PCIE or not (as it uses the
same saved PCIE capability offset).
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PCIE capability offset is saved during PCI bus walking.  Use the
value from pci_dev instead of checking in the driver and saving it off
the the driver specific structure.  Also, it will remove an unnecessary
search in the PCI configuration space if this value is referenced
instead of reacquiring it.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PCIE capability offset is saved during PCI bus walking.  It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PCIE capability offset is saved during PCI bus walking.  It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.  Also, pci_is_pcie is a
better way of determining if the device is PCIE or not (as it uses the
same saved PCIE capability offset).
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PCIE capability offset is saved during PCI bus walking.  It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.  Also, pci_is_pcie is a
better way of determining if the device is PCIE or not (as it uses the
same saved PCIE capability offset).
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>