- 24 Sep, 2016 35 commits
-
-
Kweh, Hock Leong authored
commit 36afb176 upstream. According to IIO ABI definition, IIO_PRESSURE data output unit is kilopascal: http://lxr.free-electrons.com/source/Documentation/ABI/testing/sysfs-bus-iio This patch fix output unit of HID pressure sensor IIO driver from pascal to kilopascal to follow IIO ABI definition. Signed-off-by:
Kweh, Hock Leong <hock.leong.kweh@intel.com> Reviewed-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Olof Johansson authored
commit 1c500840 upstream. In at least one known setup, the chip comes up in a state where reading the chip ID returns garbage unless it's been reset, due to noise on the wires during system boot. All supported chips have the same reset method, and based on the datasheets they all need 1.3 or 1.8ms to recover after reset. So, do the conservative thing here and always reset the chip. Signed-off-by:
Olof Johansson <olof@lixom.net> Reviewed-by:
-
Anders Darander authored
commit c2ab4474 upstream. The driver always assumes that an input device has been created when reading channel 3. This causes a kernel panic when dereferencing st->ts_input. The change was introduced in commit 84882b06 ("iio: adc: at91_adc: Add support for touchscreens without TSMR"). Earlier versions only entered that part of the if-else statement if only the following flags are set: AT91_ADC_IER_XRDY | AT91_ADC_IER_YRDY | AT91_ADC_IER_PRDY Signed-off-by:
Anders Darander <anders@chargestorm.se> Acked-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by:
-
Lars-Peter Clausen authored
commit 7d3cc21d upstream. The data buffer for captured mode for the ad799x driver is allocated in the update_scan_mode() callback. This callback is not set in the iio_info struct for the ad7791/ad7995/ad7999, which means that the data buffer is not allocated when a captured transfer is started. As a result the driver crashes when the first sample is received. To fix this properly set the update_scan_mode() callback. Fixes: d8dca330 ("staging:iio:ad799x: Preallocate sample buffer") Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Vignesh R authored
commit 7175cce1 upstream. Now that open delay and sample delay for each channel is configurable via DT, the default IDLE_TIMEOUT value is not enough as this is calculated based on hardcoded macros. This results in driver returning EBUSY sometimes. Fix this by increasing the timeout value based on maximum value possible to open delay and sample delays for each channel. Fixes: 5dc11e81 ("iio: adc: ti_am335x_adc: make sample delay, open delay, averaging DT parameters") Signed-off-by:
Vignesh R <vigneshr@ti.com> Acked-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Vignesh R authored
commit 90c43ec6 upstream. It is possible that two or more ADC channels can be simultaneously requested for raw samples, in which case there can be race in access to FIFO data resulting in loss of samples. If am335x_tsc_se_set_once() is called again from tiadc_read_raw(), when ADC is still acquired to sample one of the channels, the second process might be put into uninterruptible sleep state. Fix these issues, by protecting FIFO access and channel configurations with a mutex. Since tiadc_read_raw() might take anywhere between few microseconds to few milliseconds to finish execution (depending on averaging and delay values supplied via DT), its better to use mutex instead of spinlock. Fixes: 7ca6740c ("mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization") Signed-off-by:
-
Caesar Wang authored
commit 543852af upstream. SARADC controller needs to be reset before programming it, otherwise it will not function properly. Signed-off-by:
Caesar Wang <wxt@rock-chips.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-iio@vger.kernel.org Cc: linux-rockchip@lists.infradead.org Tested-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Alison Schofield authored
commit f8adf645 upstream. Use the iio_pollfunc_store_time parameter during triggered buffer set-up to get valid timestamps. Signed-off-by:
Alison Schofield <amsfield22@gmail.com> Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
-
Linus Walleij authored
commit 7ac61a06 upstream. Any readings from the raw interface of the KXSD9 driver will return an empty string, because it does not return IIO_VAL_INT but rather some random value from the accelerometer to the caller. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Suzuki K Poulose authored
commit 293f2936 upstream. On arm/arm64, we depend on the kvm_unmap_hva* callbacks (via mmu_notifiers::invalidate_*) to unmap the stage2 pagetables when the userspace buffer gets unmapped. However, when the Hypervisor process exits without explicit unmap of the guest buffers, the only notifier we get is kvm_arch_flush_shadow_all() (via mmu_notifier::release ) which does nothing on arm. Later this causes us to access pages that were already released [via exit_mmap() -> unmap_vmas()] when we actually get to unmap the stage2 pagetable [via kvm_arch_destroy_vm() -> kvm_free_stage2_pgd()]. This triggers crashes with CONFIG_DEBUG_PAGEALLOC, which unmaps any free'd pages from the linear map. [ 757.644120] Unable to handle kernel paging request at virtual address ffff800661e00000 [ 757.652046] pgd = ffff20000b1a2000 [ 757.655471] [ffff800661e00000] *pgd=00000047fffe3003, *pud=00000047fcd8c003, *pmd=00000047fcc7c003, *pte=00e8004661e00712 [ 757.666492] Internal error: Oops: 96000147 [#3] PREEMPT SMP [ 757.672041] Modules linked in: [ 757.675100] CPU: 7 PID: 3630 Comm: qemu-system-aar Tainted: G D 4.8.0-rc1 #3 [ 757.683240] Hardware name: AppliedMicro X-Gene Mustang Board/X-Gene Mustang Board, BIOS 3.06.15 Aug 19 2016 [ 757.692938] task: ffff80069cdd3580 task.stack: ffff8006adb7c000 [ 757.698840] PC is at __flush_dcache_area+0x1c/0x40 [ 757.703613] LR is at kvm_flush_dcache_pmd+0x60/0x70 [ 757.708469] pc : [<ffff20000809dbdc>] lr : [<ffff2000080b4a70>] pstate: 20000145 ... [ 758.357249] [<ffff20000809dbdc>] __flush_dcache_area+0x1c/0x40 [ 758.363059] [<ffff2000080b6748>] unmap_stage2_range+0x458/0x5f0 [ 758.368954] [<ffff2000080b708c>] kvm_free_stage2_pgd+0x34/0x60 [ 758.374761] [<ffff2000080b2280>] kvm_arch_destroy_vm+0x20/0x68 [ 758.380570] [<ffff2000080aa330>] kvm_put_kvm+0x210/0x358 [ 758.385860] [<ffff2000080aa524>] kvm_vm_release+0x2c/0x40 [ 758.391239] [<ffff2000082ad234>] __fput+0x114/0x2e8 [ 758.396096] [<ffff2000082ad46c>] ____fput+0xc/0x18 [ 758.400869] [<ffff200008104658>] task_work_run+0x108/0x138 [ 758.406332] [<ffff2000080dc8ec>] do_exit+0x48c/0x10e8 [ 758.411363] [<ffff2000080dd5fc>] do_group_exit+0x6c/0x130 [ 758.416739] [<ffff2000080ed924>] get_signal+0x284/0xa18 [ 758.421943] [<ffff20000808a098>] do_signal+0x158/0x860 [ 758.427060] [<ffff20000808aad4>] do_notify_resume+0x6c/0x88 [ 758.432608] [<ffff200008083624>] work_pending+0x10/0x14 [ 758.437812] Code: 9ac32042 8b010001 d1000443 8a230000 (d50b7e20) This patch fixes the issue by moving the kvm_free_stage2_pgd() to kvm_arch_flush_shadow_all(). Tested-by:
Itaru Kitayama <itaru.kitayama@riken.jp> Reported-by:
James Morse <james.morse@arm.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
-
Emanuel Czirai authored
commit d1992996 upstream. AMD F12h machines have an erratum which can cause DIV/IDIV to behave unpredictably. The workaround is to set MSRC001_1029[31] but sometimes there is no BIOS update containing that workaround so let's do it ourselves unconditionally. It is simple enough. [ Borislav: Wrote commit message. ] Signed-off-by:
Emanuel Czirai <icanrealizeum@gmail.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: Yaowu Xu <yaowu@google.com> Link: http://lkml.kernel.org/r/20160902053550.18097-1-bp@alien8.deSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Steven Rostedt authored
commit 15301a57 upstream. Łukasz Daniluk reported that on a RHEL kernel that his machine would lock up after enabling function tracer. I asked him to bisect the functions within available_filter_functions, which he did and it came down to three: _paravirt_nop(), _paravirt_ident_32() and _paravirt_ident_64() It was found that this is only an issue when noreplace-paravirt is added to the kernel command line. This means that those functions are most likely called within critical sections of the funtion tracer, and must not be traced. In newer kenels _paravirt_nop() is defined within gcc asm(), and is no longer an issue. But both _paravirt_ident_{32,64}() causes the following splat when they are traced: mm/pgtable-generic.c:33: bad pmd ffff8800d2435150(0000000001d00054) mm/pgtable-generic.c:33: bad pmd ffff8800d3624190(0000000001d00070) mm/pgtable-generic.c:33: bad pmd ffff8800d36a5110(0000000001d00054) mm/pgtable-generic.c:33: bad pmd ffff880118eb1450(0000000001d00054) NMI watchdog: BUG: soft lockup - CPU#2 stuck for 22s! [systemd-journal:469] Modules linked in: e1000e CPU: 2 PID: 469 Comm: systemd-journal Not tainted 4.6.0-rc4-test+ #513 Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v02.05 05/07/2012 task: ffff880118f740c0 ti: ffff8800d4aec000 task.ti: ffff8800d4aec000 RIP: 0010:[<ffffffff81134148>] [<ffffffff81134148>] queued_spin_lock_slowpath+0x118/0x1a0 RSP: 0018:ffff8800d4aefb90 EFLAGS: 00000246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff88011eb16d40 RDX: ffffffff82485760 RSI: 000000001f288820 RDI: ffffea0000008030 RBP: ffff8800d4aefb90 R08: 00000000000c0000 R09: 0000000000000000 R10: ffffffff821c8e0e R11: 0000000000000000 R12: ffff880000200fb8 R13: 00007f7a4e3f7000 R14: ffffea000303f600 R15: ffff8800d4b562e0 FS: 00007f7a4e3d7840(0000) GS:ffff88011eb00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7a4e3f7000 CR3: 00000000d3e71000 CR4: 00000000001406e0 Call Trace: _raw_spin_lock+0x27/0x30 handle_pte_fault+0x13db/0x16b0 handle_mm_fault+0x312/0x670 __do_page_fault+0x1b1/0x4e0 do_page_fault+0x22/0x30 page_fault+0x28/0x30 __vfs_read+0x28/0xe0 vfs_read+0x86/0x130 SyS_read+0x46/0xa0 entry_SYSCALL_64_fastpath+0x1e/0xa8 Code: 12 48 c1 ea 0c 83 e8 01 83 e2 30 48 98 48 81 c2 40 6d 01 00 48 03 14 c5 80 6a 5d 82 48 89 0a 8b 41 08 85 c0 75 09 f3 90 8b 41 08 <85> c0 74 f7 4c 8b 09 4d 85 c9 74 08 41 0f 18 09 eb 02 f3 90 8b Reported-by:
Łukasz Daniluk <lukasz.daniluk@intel.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Vineet Gupta authored
commit 1c3c9093 upstream. | CC mm/memory.o | In file included from ../mm/memory.c:53:0: | ../include/linux/pfn_t.h: In function ‘pfn_t_pte’: | ../include/linux/pfn_t.h:78:2: error: conversion to non-scalar type requested | return pfn_pte(pfn_t_to_pfn(pfn), pgprot); With STRICT_MM_TYPECHECKS pte_t is a struct and the offending code forces a cast which ends up shifting a struct and hence the gcc warning. Note that in recent past some of the arches (aarch64, s390) made STRICT_MM_TYPECHECKS default, but we don't for ARC as this leads to slightly worse generated code, given ARC ABI definition of returning structs (which pte_t would become) Quoting from ARC ABI... "Results of type struct are returned in a caller-supplied temporary variable whose address is passed in r0. For such functions, the arguments are shifted so that they are passed in r1 and up." So - struct to be returned would be allocated on stack requiring extra code at call sites - callee updates stack memory to facilitate the return (vs. simple MOV into return reg r0) Hence STRICT_MM_TYPECHECKS is not enabled by default for ARC Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Jason Gunthorpe authored
commit d1e09f30 upstream. Fixes an oops that might happen if uverbs_close races with remove_one. Both contexts may run ib_uverbs_cleanup_ucontext, it depends on the flow. Currently, there is no protection for a case that remove_one didn't make the cleanup it runs to its end, the underlying ib_device was freed then uverbs_close will call ib_uverbs_cleanup_ucontext and OOPs. Above might happen if uverbs_close deleted the file from the list then remove_one didn't find it and runs to its end. Fixes to protect against that case by a new cleanup lock so that ib_uverbs_cleanup_ucontext will be called always before that remove_one is ended. Fixes: 35d4a0b6 ("IB/uverbs: Fix race between ib_uverbs_open and remove_one") Reported-by:
Devesh Sharma <devesh.sharma@broadcom.com> Signed-off-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by:
Yishai Hadas <yishaih@mellanox.com> Signed-off-by:
Leon Romanovsky <leon@kernel.org> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Mike Snitzer authored
commit 299f6230 upstream. v4.8-rc3 commit 99f3c90d ("dm flakey: error READ bios during the down_interval") overlooked the 'drop_writes' feature, which is meant to allow reads to be issued rather than errored, during the down_interval. Fixes: 99f3c90d ("dm flakey: error READ bios during the down_interval") Reported-by:
Qu Wenruo <quwenruo@cn.fujitsu.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Mateusz Guzik authored
commit 5efc2443 upstream. Prior to the change the function would blindly deference mm, exe_file and exe_file->f_inode, each of which could have been NULL or freed. Use get_task_exe_file to safely obtain stable exe_file. Signed-off-by:
Mateusz Guzik <mguzik@redhat.com> Acked-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by:
Richard Guy Briggs <rgb@redhat.com> Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Mateusz Guzik authored
commit cd81a917 upstream. For more convenient access if one has a pointer to the task. As a minor nit take advantage of the fact that only task lock + rcu are needed to safely grab ->exe_file. This saves mm refcount dance. Use the helper in proc_exe_link. Signed-off-by:
-
Thiago Jung Bauermann authored
commit 070c43ee upstream. If kexec_apply_relocations fails, kexec_load_purgatory frees pi->sechdrs and pi->purgatory_buf. This is redundant, because in case of error kimage_file_prepare_segments calls kimage_file_post_load_cleanup, which will also free those buffers. This causes two warnings like the following, one for pi->sechdrs and the other for pi->purgatory_buf: kexec-bzImage64: Loading purgatory failed ------------[ cut here ]------------ WARNING: CPU: 1 PID: 2119 at mm/vmalloc.c:1490 __vunmap+0xc1/0xd0 Trying to vfree() nonexistent vm area (ffffc90000e91000) Modules linked in: CPU: 1 PID: 2119 Comm: kexec Not tainted 4.8.0-rc3+ #5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: dump_stack+0x4d/0x65 __warn+0xcb/0xf0 warn_slowpath_fmt+0x4f/0x60 ? find_vmap_area+0x19/0x70 ? kimage_file_post_load_cleanup+0x47/0xb0 __vunmap+0xc1/0xd0 vfree+0x2e/0x70 kimage_file_post_load_cleanup+0x5e/0xb0 SyS_kexec_file_load+0x448/0x680 ? putname+0x54/0x60 ? do_sys_open+0x190/0x1f0 entry_SYSCALL_64_fastpath+0x13/0x8f ---[ end trace 158bb74f5950ca2b ]--- Fix by setting pi->sechdrs an pi->purgatory_buf to NULL, since vfree won't try to free a NULL pointer. Link: http://lkml.kernel.org/r/1472083546-23683-1-git-send-email-bauerman@linux.vnet.ibm.comSigned-off-by:
Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Acked-by:
Baoquan He <bhe@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Dave Young <dyoung@redhat.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Trond Myklebust authored
commit b519d408 upstream. Ensure that we conform to the algorithm described in RFC5661, section 18.36.4 for when to bump the sequence id. In essence we do it for all cases except when the RPC call timed out, or in case of the server returning NFS4ERR_DELAY or NFS4ERR_STALE_CLIENTID. Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Trond Myklebust authored
commit bf0291dd upstream. According to RFC5661, the client is responsible for serialising LAYOUTGET and LAYOUTRETURN to avoid ambiguity. Consider the case where we send both in parallel. Client Server ====== ====== LAYOUTGET(seqid=X) LAYOUTRETURN(seqid=X) LAYOUTGET return seqid=X+1 LAYOUTRETURN return seqid=X+2 Process LAYOUTRETURN Forget layout stateid Process LAYOUTGET Set seqid=X+1 The client processes the layoutget/layoutreturn in the wrong order, and since the result of the layoutreturn was to clear the only existing layout segment, the client forgets the layout stateid. When the LAYOUTGET comes in, it is treated as having a completely new stateid, and so the client sets the wrong sequence id... Fix is to check if there are outstanding LAYOUTGET requests before we send the LAYOUTRETURN (note that LAYOUGET will already wait if it sees an outstanding LAYOUTRETURN). Signed-off-by:
-
Chuck Lever authored
commit 88584818 upstream. nfsd4_release_lockowner finds a lock owner that has no lock state, and drops cl_lock. Then release_lockowner picks up cl_lock and unhashes the lock owner. During the window where cl_lock is dropped, I don't see anything preventing a concurrent nfsd4_lock from finding that same lock owner and adding lock state to it. Move release_lockowner() into nfsd4_release_lockowner and hang onto the cl_lock until after the lock owner's state cannot be found again. Found by inspection, we don't currently have a reproducer. Fixes: 2c41beb0 ("nfsd: reduce cl_lock thrashing in ... ") Reviewed-by:
Jeff Layton <jlayton@redhat.com> Signed-off-by:
Chuck Lever <chuck.lever@oracle.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Trond Myklebust authored
commit 98b0f80c upstream. On error, the callers expect us to return without bumping nn->cb_users[]. Signed-off-by:
-
Trond Myklebust authored
commit b88fa69e upstream. Ensure that the client conforms to the normative behaviour described in RFC5661 Section 12.7.2: "If a client believes its lease has expired, it MUST NOT send I/O to the storage device until it has validated its lease." So ensure that we wait for the lease to be validated before using the layout. Signed-off-by:
-
Tejun Heo authored
commit df6a58c5 upstream. kernfs_notify_workfn() sends out file modified events for the scheduled kernfs_nodes. Because the modifications aren't from userland, it doesn't have the matching file struct at hand and can't use fsnotify_modify(). Instead, it looked up the inode and then used d_find_any_alias() to find the dentry and used fsnotify_parent() and fsnotify() directly to generate notifications. The assumption was that the relevant dentries would have been pinned if there are listeners, which isn't true as inotify doesn't pin dentries at all and watching the parent doesn't pin the child dentries even for dnotify. This led to, for example, inotify watchers not getting notifications if the system is under memory pressure and the matching dentries got reclaimed. It can also be triggered through /proc/sys/vm/drop_caches or a remount attempt which involves shrinking dcache. fsnotify_parent() only uses the dentry to access the parent inode, which kernfs can do easily. Update kernfs_notify_workfn() so that it uses fsnotify() directly for both the parent and target inodes without going through d_find_any_alias(). While at it, supply the target file name to fsnotify() from kernfs_node->name. Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-by:
Evgeny Vereshchagin <evvers@ya.ru> Fixes: d911d987 ("kernfs: make kernfs_notify() trigger inotify events too") Cc: John McCutchan <john@johnmccutchan.com> Cc: Robert Love <rlove@rlove.org> Cc: Eric Paris <eparis@parisplace.org> Signed-off-by:
-
Paul Mackerras authored
commit f077aaf0 upstream. In commit c60ac569 ("powerpc: Update kernel VSID range", 2013-03-13) we lost a check on the region number (the top four bits of the effective address) for addresses below PAGE_OFFSET. That commit replaced a check that the top 18 bits were all zero with a check that bits 46 - 59 were zero (performed for all addresses, not just user addresses). This means that userspace can access an address like 0x1000_0xxx_xxxx_xxxx and we will insert a valid SLB entry for it. The VSID used will be the same as if the top 4 bits were 0, but the page size will be some random value obtained by indexing beyond the end of the mm_ctx_high_slices_psize array in the paca. If that page size is the same as would be used for region 0, then userspace just has an alias of the region 0 space. If the page size is different, then no HPTE will be found for the access, and the process will get a SIGSEGV (since hash_page_mm() will refuse to create a HPTE for the bogus address). The access beyond the end of the mm_ctx_high_slices_psize can be at most 5.5MB past the array, and so will be in RAM somewhere. Since the access is a load performed in real mode, it won't fault or crash the kernel. At most this bug could perhaps leak a little bit of information about blocks of 32 bytes of memory located at offsets of i * 512kB past the paca->mm_ctx_high_slices_psize array, for 1 <= i <= 11. Fixes: c60ac569 ("powerpc: Update kernel VSID range") Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Reviewed-by:
Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Mukesh Ojha authored
commit a9cbf0b2 upstream. In a situation, where Linux kernel gets notified about duplicate error log from OPAL, it is been observed that kernel fails to remove sysfs entries (/sys/firmware/opal/elog/0xXXXXXXXX) of such error logs. This is because, we currently search the error log/dump kobject in the kset list via 'kset_find_obj()' routine. Which eventually increment the reference count by one, once it founds the kobject. So, unless we decrement the reference count by one after it found the kobject, we would not be able to release the kobject properly later. This patch adds the 'kobject_put()' which was missing earlier. Signed-off-by:
Mukesh Ojha <mukesh02@linux.vnet.ibm.com> Reviewed-by:
Vasant Hegde <hegdevasant@linux.vnet.ibm.com> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Nicholas Piggin authored
commit cc7786d3 upstream. tabort_syscall runs with RI=1, so a nested recoverable machine check will load the paca into r13 and overwrite what we loaded it with, because exceptions returning to privileged mode do not restore r13. Fixes: b4b56f9e (powerpc/tm: Abort syscalls in active transactions) Signed-off-by:
Nick Piggin <npiggin@gmail.com> Signed-off-by:
-
Jon Paul Maloy authored
commit c7cad0d6 upstream. In commit 5cbb28a4 ("tipc: linearize arriving NAME_DISTR and LINK_PROTO buffers") we added linearization of NAME_DISTRIBUTOR, LINK_PROTOCOL/RESET and LINK_PROTOCOL/ACTIVATE to the function tipc_udp_recv(). The location of the change was selected in order to make the commit easily appliable to 'net' and 'stable'. We now move this linearization to where it should be done, in the functions tipc_named_rcv() and tipc_link_proto_rcv() respectively. Reviewed-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Juerg Haefliger <juerg.haefliger@hpe.com> Signed-off-by:
-
Wenwei Tao authored
commit 16c6d048 upstream. The bio is not returned if the data page cannot be allocated. Signed-off-by:
Wenwei Tao <ww.tao0320@gmail.com> Signed-off-by:
Matias Bjørling <m@bjorling.me> Signed-off-by:
Jens Axboe <axboe@fb.com> Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by:
-
Eric Biggers authored
commit ba63f23d upstream. Since setting an encryption policy requires writing metadata to the filesystem, it should be guarded by mnt_want_write/mnt_drop_write. Otherwise, a user could cause a write to a frozen or readonly filesystem. This was handled correctly by f2fs but not by ext4. Make fscrypt_process_policy() handle it rather than relying on the filesystem to get it right. Signed-off-by:
Eric Biggers <ebiggers@google.com> Cc: stable@vger.kernel.org # 4.1+; check fs/{ext4,f2fs} Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Acked-by:
Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by:
-
Paolo Bonzini authored
[the change is part of 70e4da7a, which is already in stable kernels 4.1.y to 4.4.y. this part of the fix however was later undone, so remove the line again] The following patches were applied in the wrong order in -stable. This is the order as they appear in Linus' tree, [0] commit 4e422bdd ("KVM: x86: fix missed hardware breakpoints") [1] commit 172b2386 ("KVM: x86: fix missed hardware breakpoints") [2] commit 70e4da7a ("KVM: x86: fix root cause for missed hardware breakpoints") but this is the order for linux-4.4.y [1] commit fc90441e ("KVM: x86: fix missed hardware breakpoints") [2] commit 25e86186 ("KVM: x86: fix root cause for missed hardware breakpoints") [0] commit 0f6e5e26 ("KVM: x86: fix missed hardware breakpoints") The upshot is that KVM_DEBUGREG_RELOAD is always set when returning from kvm_arch_vcpu_load() in stable, but not in Linus' tree. This happened because [0] and [1] are the same patch. [0] and [1] come from two different merges, and the later merge is trivially resolved; when [2] is applied it reverts both of them. Instead, when using the [1][2][0] order, patches applies normally but "KVM: x86: fix missed hardware breakpoints" is present in the final tree. Reported-by:
Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
James Hogan authored
commit ba913e4f upstream. When mapping a page into the guest we error check using is_error_pfn(), however this doesn't detect a value of KVM_PFN_NOSLOT, indicating an error HVA for the page. This can only happen on MIPS right now due to unusual memslot management (e.g. being moved / removed / resized), or with an Enhanced Virtual Memory (EVA) configuration where the default KVM_HVA_ERR_* and kvm_is_error_hva() definitions are unsuitable (fixed in a later patch). This case will be treated as a pfn of zero, mapping the first page of physical memory into the guest. It would appear the MIPS KVM port wasn't updated prior to being merged (in v3.10) to take commit 81c52c56 ("KVM: do not treat noslot pfn as a error pfn") into account (merged v3.8), which converted a bunch of is_error_pfn() calls to is_error_noslot_pfn(). Switch to using is_error_noslot_pfn() instead to catch this case properly. Fixes: 858dd5d4 ("KVM/MIPS32: MMU/TLB operations for the Guest.") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by:
-
Chen-Yu Tsai authored
commit b53e7d00 upstream. The bootloader (U-boot) sometimes uses this timer for various delays. It uses it as a ongoing counter, and does comparisons on the current counter value. The timer counter is never stopped. In some cases when the user interacts with the bootloader, or lets it idle for some time before loading Linux, the timer may expire, and an interrupt will be pending. This results in an unexpected interrupt when the timer interrupt is enabled by the kernel, at which point the event_handler isn't set yet. This results in a NULL pointer dereference exception, panic, and no way to reboot. Clear any pending interrupts after we stop the timer in the probe function to avoid this. Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by:
-
Eric Biggers authored
commit 163ae1c6 upstream. On an ext4 or f2fs filesystem with file encryption supported, a user could set an encryption policy on any empty directory(*) to which they had readonly access. This is obviously problematic, since such a directory might be owned by another user and the new encryption policy would prevent that other user from creating files in their own directory (for example). Fix this by requiring inode_owner_or_capable() permission to set an encryption policy. This means that either the caller must own the file, or the caller must have the capability CAP_FOWNER. (*) Or also on any regular file, for f2fs v4.6 and later and ext4 v4.8-rc1 and later; a separate bug fix is coming for that. Signed-off-by:
-
Konstantin Khlebnikov authored
commit adb7ef60 upstream. This might be unexpected but pages allocated for sbi->s_buddy_cache are charged to current memory cgroup. So, GFP_NOFS allocation could fail if current task has been killed by OOM or if current memory cgroup has no free memory left. Block allocator cannot handle such failures here yet. Signed-off-by:
-
- 15 Sep, 2016 5 commits
-
-
Greg Kroah-Hartman authored
-
Nicolai Stange authored
commit f2d1362f upstream. Currently, if the number of leading zeros is greater than fits into a complete limb, mpi_write_sgl() skips them by iterating over them limb-wise. However, it fails to adjust its internal leading zeros tracking variable, lzeros, accordingly: it does a p -= sizeof(alimb); continue; which should really have been a lzeros -= sizeof(alimb); continue; Since lzeros never decreases if its initial value >= sizeof(alimb), nothing gets copied by mpi_write_sgl() in that case. Instead of skipping the high order zero limbs within the loop as shown above, fix the issue by adjusting the copying loop's bounds. Fixes: 2d4d1eea ("lib/mpi: Add mpi sgl helpers") Signed-off-by:
Nicolai Stange <nicstange@gmail.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Mika Båtsman authored
commit 8a092e68 upstream. Bypass support was added in commit d38018f2 ("regulator: anatop: Add bypass support to digital LDOs"). A check for valid voltage selectors was added in commit da0607c8 ("regulator: anatop: Fail on invalid voltage selector") but it also discards all regulators that are in bypass mode. Add check for the bypass setting. Errors below were seen on a Variscite mx6 board. anatop_regulator 20c8000.anatop:regulator-vddcore@140: Failed to read a valid default voltage selector. anatop_regulator: probe of 20c8000.anatop:regulator-vddcore@140 failed with error -22 anatop_regulator 20c8000.anatop:regulator-vddsoc@140: Failed to read a valid default voltage selector. anatop_regulator: probe of 20c8000.anatop:regulator-vddsoc@140 failed with error -22 Fixes: da0607c8 ("regulator: anatop: Fail on invalid voltage selector") Signed-off-by:
Mika Båtsman <mbatsman@mvista.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Krzysztof Kozlowski authored
commit 48a61e1e upstream. Add proper error path (for disabling runtime PM) when registering of hwrng fails. Fixes: b329669e ("hwrng: exynos - Add support for Exynos random number generator") Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
-
Sai Gurrappadi authored
commit e43e94c1 upstream. Currently, the userspace governor only updates frequency on GOV_LIMITS if policy->cur falls outside policy->{min/max}. However, it is also necessary to update current frequency on GOV_LIMITS to match the user requested value if it can be achieved within the new policy->{max/min}. This was previously the behaviour in the governor until commit d1922f02 ("cpufreq: Simplify userspace governor") which incorrectly assumed that policy->cur == user requested frequency via scaling_setspeed. This won't be true if the user requested frequency falls outside policy->{min/max}. Ex: a temporary thermal cap throttled the user requested frequency. Fix this by storing the user requested frequency in a seperate variable. The governor will then try to achieve this request on every GOV_LIMITS change. Fixes: d1922f02 (cpufreq: Simplify userspace governor) Signed-off-by:
Sai Gurrappadi <sgurrappadi@nvidia.com> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
