- 26 Aug, 2017 13 commits
-
-
Arvind Yadav authored
i2c_device_id are not supposed to change at runtime. All functions working with i2c_device_id provided by <linux/i2c.h> work with const i2c_device_id. So mark the non-const structs as const. Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Arvind Yadav authored
i2c_device_id are not supposed to change at runtime. All functions working with i2c_device_id provided by <linux/i2c.h> work with const i2c_device_id. So mark the non-const structs as const. Signed-off-by:
-
Bhumika Goyal authored
Make these const as they are only used in a copy operation. Done using Coccinelle Signed-off-by:
Bhumika Goyal <bhumirks@gmail.com> Acked-by:
Mike Isely <isely@pobox.com> Signed-off-by:
-
Bhumika Goyal authored
Make this const as it is only used in a copy operation. Done using Coccinelle Signed-off-by:
-
Bhumika Goyal authored
Make these const as they are only used in a copy operation. Done using Coccinelle Signed-off-by:
-
Bhumika Goyal authored
Make this const as it is only stored in the type field of a device structure, which is const. Done using Coccinelle. Signed-off-by:
-
Bhumika Goyal authored
Make these const as they are only used in a copy operation or are stored in the algo field of i2c_adapter structure, which is const. Signed-off-by:
-
Hans Verkuil authored
Use the new CEC_CAP_DEFAULTS define in this driver. Signed-off-by:
Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by:
-
Hans Verkuil authored
Use the new CEC_CAP_DEFAULTS define in this driver. This also adds the CEC_CAP_RC capability which was missing here (and this is also the reason for this new define, to avoid missing such capabilities). Signed-off-by:
-
Hans Verkuil authored
Only the first HDMI input has a CEC adapter, so just report 'HDMI 0' as the HDMI input name. For the HDMI outputs use bus_cnt instead of i as the output number. The HDMI name now corresponds to what 'v4l2-ctl --list-outputs' reports. Signed-off-by:
-
Hans Verkuil authored
Add support to emulate CEC pin monitoring. There are few hardware devices that support this, so being able to emulate it here helps developing software for this. Signed-off-by:
-
Hans Verkuil authored
The current CEC pin value (0 or 1) was part of the cec_pin struct, but that assumes that CEC pin monitoring can only be used with a driver that uses the low-level CEC pin framework. But hardware that has both a high-level API and can monitor the CEC pin at low-level at the same time does not need to depend on the cec pin framework. To support such devices remove the cur_value field from struct cec_pin and add a cec_pin_is_high field to cec_adapter. This also makes it possible to drop the '#ifdef CONFIG_CEC_PIN' in cec-api.c. Signed-off-by:
-
Hans Verkuil authored
When the adapter is removed the cec_delete_adapter() call attempts to set the physical address to INVALID by calling __cec_s_phys_addr() and so disabling the adapter. However, __cec_s_phys_addr checks if the device node was unregistered and just returns in that case. This means that the adap_enable callback is never called with 'false' to disable the CEC adapter. Most drivers don't care, but some need to do cleanup here. Change the test so the adapter is correctly disabled, even when the device node is unregistered. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
- 20 Aug, 2017 27 commits
-
-
Fengguang Wu authored
drivers/media/pci/ddbridge/ddbridge-maxs8.c:145:2-3: Unneeded semicolon drivers/media/pci/ddbridge/ddbridge-maxs8.c:173:2-3: Unneeded semicolon Remove unneeded semicolon. Generated by: scripts/coccinelle/misc/semicolon.cocci Fixes: a43dbe430fb4 ("media: ddbridge: support MaxLinear MXL5xx based cards (MaxS4/8)") CC: Daniel Scheller <d.scheller@gmx.net> Signed-off-by:Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
-
Jemma Denson authored
This Kaffeine's BZ: https://bugs.kde.org/show_bug.cgi?id=374693 affects SkyStar S2 PCI DVB-S/S2 rev 3.3 device. It could be due to a Kernel bug. While checking the Isil 6421, comparing with its manual, available at: http://www.intersil.com/content/dam/Intersil/documents/isl6/isl6421a.pdf It was noticed that, if the output load is highly capacitive, a different approach is recomended when energizing the LNBf. Also, it is possible to detect if a current overload is happening, by checking an special flag. Add support for it. Tested on Skystar S2. Changes respect override_or option so should still work fine on cx88 based cards which disable dynamic current limit. Changes since v1: v2 - fixed incorrect checking of i2c return values v3 - fix if logic to check if dcl needs re-enabling - respect override_or values which aim to disable dcl - only do long sleep on overload if dcl enabled - add short sleep before re-enabling dcl - only check overload and potentially return EINVAL if device is on v4 - revert v3 sleep logic changes to remove tuning delays Signed-off-by:
Jemma Denson <jdenson@gmail.com>
-
Daniel Scheller authored
Fixes: stv6111.c:665:24: warning: Using plain integer as NULL pointer Signed-off-by:
Daniel Scheller <d.scheller@gmx.net> Signed-off-by:
-
Daniel Scheller authored
Cleans up smatch warning: symbol 'stvlist' was not declared. Should it be static? Patch originally submitted by Colin Ian King <colin.king@canonical.com>, remainder after the merge of all other stv0910 fixes. Cc: Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Sean Young authored
RC_TYPE is confusing and it's just the protocol. So rename it. Suggested-by:
Sean Young <sean@mess.org> Acked-by:
-
Hans Verkuil authored
The 'Press and Hold' operation was not correctly implemented, in particular the requirement that the repeat doesn't start until the second identical keypress arrives. The REP_DELAY value also had to be adjusted (see the comment in the code) to achieve the desired behavior. The 'enabled_protocols' field was also never set, fix that too. Since CEC is a fixed protocol the driver has to set this field. Signed-off-by:
-
Sean Young authored
CEC needs a keypress timeout of 550ms, which is too high for the IR protocols. Also fill in known repeat times, with 50ms error margin. Also, combine all protocol data into one structure. Signed-off-by:
-
Sean Young authored
Any protocol for which we have a software decoder, can be enabled. Without this only the loaded protocol decoders can be selected. Signed-off-by:
-
Sean Young authored
If rc_validate_filter() is called for CEC or XMP, then we would read beyond the end of the array. Suggested-by:
-
Sean Young authored
Since commit 12749b198fa4 ("[media] rc: saa7134: add trailing space for timely decoding"), the workaround of inserting reset events is no longer needed. Note that the initial reset is not needed either; other rc-core drivers that don't use ir_raw_event_store_edge() never call this at all. Verified on a HVR-1150 and Raspberry Pi. Fixes: 3f5c4c73 ("[media] rc: fix ghost keypresses with certain hw") Signed-off-by: -
Sean Young authored
The gpio-ir-recv driver adds timeouts which the saa7134 lacks; this causes keypress not to arrive, and to only arrive once more IR is received. This is what the commit below calls "ghost keypresses", and that commit does not solve the issue completely. This makes the IR on the HVR-1150 much more reliable and responsive. Fixes: 3f5c4c73 ("[media] rc: fix ghost keypresses with certain hw") Signed-off-by:
-
Sean Young authored
The gpio-ir-recv driver does many wakeups (once per edge); the saa7134 driver has special handling to only wakeup 15ms after the first edge. Make this part of rc-core so gpio-ir-recv also benefits from this (so a rc-5 keypress now causes 3 wakeups rather than 24). Signed-off-by:
-
Sean Young authored
We're reading beyond the buffer before checking its length. BUG: KASAN: slab-out-of-bounds in wbcir_irq_tx Signed-off-by:
-
Sean Young authored
This causes out-of-bounds read on device probe. BUG: KASAN: slab-out-of-bounds in mceusb_dev_printdata+0xdc/0x830 [mceusb] Signed-off-by:
-
Sean Young authored
This driver cannot send pulse, it only accepts driver-dependent codes. Cc: <stable@vger.kernel.org> # v3.2 Signed-off-by:
-
Shawn Guo authored
It adds the remote control driver and corresponding keymap file for IRDEC block found on ZTE ZX family SoCs. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Shawn Guo authored
It adds the dt-bindings document for ZTE ZX IRDEC remote control block. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Shawn Guo authored
The NEC scancode composing and protocol type detection in ir_nec_decode() is generic enough to be a shared function. Let's create an inline function in rc-core.h, so that other remote control drivers can reuse this function to save some code. Signed-off-by:
-
Philipp Zabel authored
Commit a53e35db ("reset: Ensure drivers are explicit when requesting reset lines") started to transition the reset control request API calls to explicitly state whether the driver needs exclusive or shared reset control behavior. Convert all drivers requesting exclusive resets to the explicit API call so the temporary transition helpers can be removed. No functional changes. Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Chen-Yu Tsai <wens@csie.org> Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Philipp Zabel authored
Commit a53e35db ("reset: Ensure drivers are explicit when requesting reset lines") started to transition the reset control request API calls to explicitly state whether the driver needs exclusive or shared reset control behavior. Convert all drivers requesting exclusive resets to the explicit API call so the temporary transition helpers can be removed. No functional changes. Cc: Patrice Chotard <patrice.chotard@st.com> Signed-off-by:
-
Heiner Kallweit authored
Transmit support in this driver was never tested and based on the code it can't work. Just one example: The buffer provided to nvt_tx_ir holds unsigned int values in micro seconds: First value is for a pulse, second for a pause, etc. Bytes in this buffer are copied as-is to the chip FIFO what can't work as the chip-internal format is totally different. See also conversion done in nvt_process_rx_ir_data. Even if we would try to fix this we have the issue that we can't test it. There seems to be no device on the market using IR transmit with one of the chips supported by this driver. To facilitate maintenance of the driver I'd propose to remove the rudimentary transmit support. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Yves Lemée authored
According the coding style guidelines, the ENOSYS error code must be returned in case of a non existent system call. This code has been replaced with the ENOTTY error code indicating a missing functionality. Signed-off-by:
Yves Lemée <yves.lemee.kernel@gmail.com> Signed-off-by:
-
Sean Young authored
Document the device tree bindings for the GPIO IR Bit Banging Transmitter. Signed-off-by:
-
Sean Young authored
Document the device tree bindings for the PWM IR Transmitter. Signed-off-by:
-
Sean Young authored
This is new driver which uses pwm, so it is more power-efficient than the bit banging gpio-ir-tx driver. Signed-off-by:
Pavel Machek <pavel@ucw.cz> Tested-by:
Matthias Reichl <hias@horus.com> Signed-off-by:
-
Sean Young authored
This is a simple bit-banging GPIO IR TX driver. Signed-off-by:
-
Sean Young authored
Without this patch, an input device is created which is not necessary. Signed-off-by:
-
