commit a20047f3 upstream.

The private baud_rate variable is used to configure the port at open and
reset-resume and must never be set to (and left at) zero or reset-resume
and all further open attempts will fail.

Fixes: aa91def4 ("USB: ch341: set tty baud speed according to tty
struct")
Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Signed-off-by: Johan Hovold <johan@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 4e2da446 upstream.

DTR and RTS will be asserted by the tty-layer when the port is opened
and deasserted on close (if HUPCL is set). Make sure the initial state
is not-asserted before the port is first opened as well.

Fixes: 664d5df9 ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 4e46c410 upstream.

Changing the LCR register after initialization does not seem to be reliable
on all chips (particularly not on CH341A). Restructure initialization and
configuration to always reinit the chip on configuration changes instead and
pass the LCR register value directly to the initialization command.

(Note that baud rates above 500kbaud are incorrect, but they're incorrect in
the same way both before and after this patch at least on the CH340G. Fixing
this isn't a priority as higher baud rates don't seem that reliable anyway.)

Cleaned-up version of a patch by Grigori Goronzy
Signed-off-by: Aidan Thornton <makosoft@gmail.com>
Reviewed-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 6fde8d29 upstream.

No functional changes, this just gives names to some registers and USB
requests based on Grigori Goronzy's work and WinChipTech's Linux driver
(which reassuringly agree), then uses them in place of magic numbers.
This also renames the misnamed BREAK2 register (actually UART config)
Signed-off-by: Aidan Thornton <makosoft@gmail.com>
Reviewed-by: Grigori Goronzy <greg@chown.ath.cx>
Signed-off-by: Johan Hovold <johan@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit aa91def4 upstream.

The ch341_set_baudrate() function initialize the device baud speed
according to the value on priv->baud_rate. By default the ch341_open() set
it to a hardcoded value (DEFAULT_BAUD_RATE 9600). Unfortunately, the
tty_struct is not initialized with the same default value. (usually 56700)

This means that the tty_struct and the device baud rate generator are not
synchronized after opening the port.

Fixup is done by calling ch341_set_termios() if tty exist.
Remove unnecessary variable priv->baud_rate setup as it's already done by
ch341_port_probe().
Remove unnecessary call to ch341_set_{handshake,baudrate}() in
ch341_open() as there already called in ch341_configure() and
ch341_set_termios()
Signed-off-by: Nicolas PLANEL <nicolas.planel@enovance.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 394a1033 upstream.

Remove redundant call to ch341_close from error path when submission of
the interrupt urb fails in open.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit fac69d0e upstream.

Add the missing declarations of basic string functions to string.h to allow
a clean build.

Fixes: 5be86566 ("String-handling functions for the new x86 setup code.")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Link: http://lkml.kernel.org/r/1483781911-21399-1-git-send-email-hofrat@osadl.orgSigned-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 8a08403b upstream.

fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=98897
https://bugs.launchpad.net/bugs/1651981Acked-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Adrian Fiergolski <A.Fiergolski@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 064c3db9 upstream.

Here, If devm_ioremap will fail. It will return NULL.
Then hpriv->base = NULL - 0x20000; Kernel can run into
a NULL-pointer dereference. This error check will avoid
NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 0f1f9cbc upstream.

The R8A7740 GEther controller supports the packet checksum offloading
but the 'hw_crc' (bad name, I'll fix it) flag isn't set in the R8A7740
data,  thus CSMR isn't cleared...

Fixes: 73a0d907 ("net: sh_eth: add support R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 978d3639 upstream.

As the SH77{34|63} manuals are freely available,  I've checked the EESIPR
values written against the manuals, and they appeared to set the reserved
bits 11-15 (which should be 0 on write). Fix those EESIPR values.

Fixes: 380af9e3 ("net: sh_eth: CPU dependency code collect to "struct sh_eth_cpu_data"")
Fixes: f5d12767 ("sh_eth: get SH77{34|63} support out of #ifdef")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit fd7c9914 upstream.

Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 1ebb7114 upstream.

Make sure we have enough of a report structure to validate before
looking at it.
Reported-by: Benoit Camredon <benoit.camredon@airbus.com>
Tested-by: Benoit Camredon <benoit.camredon@airbus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 3659f98b upstream.

Nothing in this minimal script seems to require bash. We often run these
tests on embedded devices where the only shell available is the busybox
ash. Use sh instead.
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 0a8fd134 upstream.

When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses.  This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:

WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...

CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
 ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c
 ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510
 ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000
Call Trace:
 [<     inline     >] __dump_stack lib/dump_stack.c:15
 [<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51
 [<ffffffff8168c88e>] panic+0x1cb/0x3a9 kernel/panic.c:179
 [<ffffffff812b80b4>] __warn+0x1c4/0x1e0 kernel/panic.c:542
 [<ffffffff812b8195>] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565
 [<ffffffff819e70ca>] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30
 [<ffffffff819e7308>] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59
 [<     inline     >] create_dir lib/kobject.c:71
 [<ffffffff81fa1b07>] kobject_add_internal+0x227/0xa60 lib/kobject.c:229
 [<     inline     >] kobject_add_varg lib/kobject.c:366
 [<ffffffff81fa2479>] kobject_add+0x139/0x220 lib/kobject.c:411
 [<ffffffff82737a63>] device_add+0x353/0x1660 drivers/base/core.c:1088
 [<ffffffff82738d8d>] device_register+0x1d/0x20 drivers/base/core.c:1206
 [<ffffffff82cb77d3>] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195
 [<ffffffff82c9f27b>] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030
 [<ffffffff82ca39d3>] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937
 [<ffffffff82cc9e2e>] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172
 [<ffffffff82caa7fa>] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263

This patch prevents the problem by checking for duplicate endpoint
addresses during enumeration and skipping any duplicates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 674aea07 upstream.

This device gives the following error on detection.
xhci_hcd 0000:00:11.0: ERROR Transfer event for disabled endpoint or
incorrect stream ring

The same error is not seen when it is added to unusual_device
list with US_FL_NO_REPORT_OPCODES passed.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Oliver Neukum <oneukun@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 3bc02bce upstream.

If CONFIG_PM=n:

    drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
    drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here

To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.

Fixes: 37be6676 ("usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 8c300fe2 upstream.

When unloading omap2430, we can get the following splat:

WARNING: CPU: 1 PID: 295 at kernel/irq/manage.c:1478 __free_irq+0xa8/0x2c8
Trying to free already-free IRQ 4
...
[<c01a8b78>] (free_irq) from [<bf0aea84>]
(musbhs_dma_controller_destroy+0x28/0xb0 [musb_hdrc])
[<bf0aea84>] (musbhs_dma_controller_destroy [musb_hdrc]) from
[<bf09f88c>] (musb_remove+0xf0/0x12c [musb_hdrc])
[<bf09f88c>] (musb_remove [musb_hdrc]) from [<c056a384>]
(platform_drv_remove+0x24/0x3c)
...

This is because the irq number in use is 260 nowadays, and the dma
controller is using u8 instead of int.

Fixes: 6995eb68 ("USB: musb: enable low level DMA operation for Blackfin")
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: added Fixes tag]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 32eb12a6 upstream.

Flush the KVM entry code from the icache on all CPUs, not just the one
that built the entry code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit dd853fd2 upstream.

A negative number can be specified in the cmdline which will be used as
setup_clear_cpu_cap() argument. With that we can clear/set some bit in
memory predceeding boot_cpu_data/cpu_caps_cleared which may cause kernel
to misbehave. This patch adds lower bound check to setup_disablecpuid().

Boris Petkov reproduced a crash:

  [    1.234575] BUG: unable to handle kernel paging request at ffffffff858bd540
  [    1.236535] IP: memcpy_erms+0x6/0x10
Signed-off-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: andi.kleen@intel.com
Cc: bp@alien8.de
Cc: dave.hansen@linux.intel.com
Cc: luto@kernel.org
Cc: slaoub@gmail.com
Fixes: ac72e788 ("x86: add generic clearcpuid=... option")
Link: http://lkml.kernel.org/r/1482933340-11857-1-git-send-email-lukasz.odzioba@intel.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 71eae1ca upstream.

The RX descriptor word 0 on SH7734 has the RFS[9:0] field in bits 16-25
(bits  0-15 usually used for that are occupied by the packet checksum).
Thus  we need to set the 'shift_rd0'  field in the SH7734 SoC data...

Fixes: f0e81fec ("net: sh_eth: Add support SH7734")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit c7efff92 upstream.

Although the old quirk table showed ASUS X71SL with ALC663 codec being
compatible with asus-mode3 fixup, the bugzilla reporter explained that
asus-model8 fits better for the dual headphone controls.  So be it.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=191781Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 38e5a855 upstream.

Inserting the TSB means adding an extra 8 bytes in front the of packet
that is going to be used as metadata information by the TDMA engine, but
stripped off, so it does not really help with the packet padding.

For some odd packet sizes that fall below the 60 bytes payload (e.g: ARP)
we can end-up padding them after the TSB insertion, thus making them 64
bytes, but with the TDMA stripping off the first 8 bytes, they could
still be smaller than 64 bytes which is required to ingress the switch.

Fix this by swapping the padding and TSB insertion, guaranteeing that
the packets have the right sizes.

Fixes: 80105bef ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit e09ee853 upstream.

The credentials handling was pushed to the write handlers
but error handling wasn't done properly.
Move write callbacks to completion queue to destroy them
and to notify a blocked writer about the failure

Fixes: 136698e5 (mei: push credentials inside the irq write handler)
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 432abf68 upstream.

The generic command buffer entry is 128 bits (16 bytes), so the offset
of tail and head pointer should be 16 bytes aligned and increased with
0x10 per command.

When cmd buf is full, head = (tail + 0x10) % CMD_BUFFER_SIZE.

So when left space of cmd buf should be able to store only two
command, we should be issued one COMPLETE_WAIT additionally to wait
all older commands completed. Then the left space should be increased
after IOMMU fetching from cmd buf.

So left check value should be left <= 0x20 (two commands).
Signed-off-by: Huang Rui <ray.huang@amd.com>
Fixes: ac0ea6e9 ('x86/amd-iommu: Improve handling of full command buffer')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 85bcf96c upstream.

ASUS ROG Ranger VIII with ALC1150 codec requires the extra GPIO pin to
up for the front panel.  Just use the existing fixup for setting up
the GPIO pins.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189411Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit ef079936 upstream.

Fix NULL-pointer dereference in open() should a malicious device lack
the expected endpoints:

Unable to handle kernel NULL pointer dereference at virtual address 00000030
..
[<bf06a6b0>] (ti_open [ti_usb_3410_5052]) from [<bf02e118>] (serial_port_activate+0x68/0x98 [usbserial])

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit cc090924 upstream.

Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:

Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at spcp8x5_open+0x30/0xd0 [spcp8x5]

Fixes: 619a6f1d ("USB: add usb-serial spcp8x5 driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit f09d1886 upstream.

The write URB was being killed using the synchronous interface while
holding a spin lock in close().

Simply drop the lock and busy-flag update, something which would have
been taken care of by the completion handler if the URB was in flight.

Fixes: f7a33e60 ("USB: serial: add quatech2 usb to serial driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 76ab439e upstream.

Fix NULL-pointer dereference in open() should a type-0 or type-1 device
lack the expected endpoints:

Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at pl2303_open+0x38/0xec [pl2303]

Note that a missing interrupt-in endpoint would have caused open() to
fail.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 5afeef23 upstream.

Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:

Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at oti6858_open+0x30/0x1d0 [oti6858]

Note that a missing interrupt-in endpoint would have caused open() to
fail.

Fixes: 49cdee0e ("USB: oti6858 usb-serial driver (in Nokia CA-42
cable)")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit a5bc0194 upstream.

Fix NULL-pointer dereferences at open() and disconnect() should the
device lack the expected bulk-out endpoints:

Unable to handle kernel NULL pointer dereference at virtual address 000000b4
...
[c0170ff0>] (__lock_acquire) from [<c0172f00>] (lock_acquire+0x108/0x264)
[<c0172f00>] (lock_acquire) from [<c06a5090>] (_raw_spin_lock_irqsave+0x58/0x6c)
[<c06a5090>] (_raw_spin_lock_irqsave) from [<c0470684>] (tty_port_tty_set+0x28/0xa4)
[<c0470684>] (tty_port_tty_set) from [<bf08d384>] (omninet_open+0x30/0x40 [omninet])
[<bf08d384>] (omninet_open [omninet]) from [<bf07c118>] (serial_port_activate+0x68/0x98 [usbserial])

Unable to handle kernel NULL pointer dereference at virtual address 00000234
...
[<bf01f418>] (omninet_disconnect [omninet]) from [<bf0016c0>] (usb_serial_disconnect+0xe4/0x100 [usbserial])

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 472d7e55 upstream.

The interrupt URB is killed at final port close since commit
0de9a702 ("USB: overhaul of mos7840 driver").

Fixes: 0de9a702 ("USB: overhaul of mos7840 driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 5c75633e upstream.

Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:

Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at mos7840_open+0x88/0x8dc [mos7840]

Note that we continue to treat the interrupt-in endpoint as optional for
now.

Fixes: 3f542974 ("USB: Moschip 7840 USB-Serial Driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit fde1faf8 upstream.

A static usb-serial-driver structure that is used to initialise the
interrupt URB was modified during probe depending on the currently
probed device type, something which could break a parallel probe of a
device of a different type.

Fix this up by overriding the default completion callback for MCS7715
devices in attach() instead. We may want to use two usb-serial driver
instances for the two types later.

Fixes: fb088e33 ("USB: serial: add support for serial port on the
moschip 7715")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 75dd211e upstream.

Do not submit the interrupt URB until after the parport has been
successfully registered to avoid another use-after-free in the
completion handler when accessing the freed parport private data in case
of a racing completion.

Fixes: b69578df ("USB: usbserial: mos7720: add support for parallel
port on moschip 7715")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 91a1ff4d upstream.

The interrupt URB was submitted on probe but never stopped on probe
errors. This can lead to use-after-free issues in the completion
handler when accessing the freed usb-serial struct:

Unable to handle kernel paging request at virtual address 6b6b6be7
...
[<bf052e70>] (mos7715_interrupt_callback [mos7720]) from [<c052a894>] (__usb_hcd_giveback_urb+0x80/0x140)
[<c052a894>] (__usb_hcd_giveback_urb) from [<c052a9a4>] (usb_hcd_giveback_urb+0x50/0x138)
[<c052a9a4>] (usb_hcd_giveback_urb) from [<c0550684>] (musb_giveback+0xc8/0x1cc)

Fixes: b69578df ("USB: usbserial: mos7720: add support for parallel
port on moschip 7715")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit b05aebc2 upstream.

Fix NULL-pointer dereference at port open if a device lacks the expected
bulk in and out endpoints.

Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
[<bf071c20>] (mos7720_open [mos7720]) from [<bf0490e0>] (serial_port_activate+0x68/0x98 [usbserial])
[<bf0490e0>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8)
[<c0470ca4>] (tty_port_open) from [<bf049d98>] (serial_open+0x48/0x6c [usbserial])
[<bf049d98>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc)

Fixes: 0f64478c ("USB: add USB serial mos7720 driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 21ce5784 upstream.

Fix NULL-pointer dereference in write() should the device lack the
expected interrupt-out endpoint:

Unable to handle kernel NULL pointer dereference at virtual address 00000054
...
PC is at kobil_write+0x144/0x2a0 [kobil_sct]

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>

commit 5d9b0f85 upstream.

Check for the expected endpoints in attach() and fail loudly if not
present.

Note that failing to do this appears to be benign since da280e34
("USB: keyspan_pda: clean up write-urb busy handling") which prevents a
NULL-pointer dereference in write() by never marking a non-existent
write-urb as free.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>