Add the TI drv2665 piezo haptic driver.  This haptics IC requires the data
to be streamed to the FIFO for continuous output.

Datasheet can be found at:
http://www.ti.com/product/drv2665Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fix spelling of magnitude
s/manginude/magnitude
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fix the Kconfig for the drv2667 as there was a copy/paste error.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.

Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.

The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.

In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The MSB of the first byte read via I2C at the coordinates address
indicates whether the data is valid or ready (called "buffer status" in
the datasheets) when an interrupt is raised. Previously, this bit was
ignored, which resulted in a lot of incorrect detections of "finger
removed" events.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The event mask was specified as 0xF (4 bits) when in reality is 0x1F (5
bits) in order to be capable of representing all FIFO length values from
0 to 16.

This caused a problem: when the keypad reported 16 pending events the
driver took it as 0, and did nothing. This in turn caused the keypad to
re-issue the interrupt over and over again.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The pull mask is created by looping each row (column) and building an
8-bit integer with the configuration. It is written byte-by-byte, when
we reach the end of the rows (columns) or we're at the 3rd line (which
finishes the first byte, since each pin is 2bits on the mask).

However, this only works if we have at most 8 pins (2 bytes), which is
not the case for the ADP5589. So, write the byte at each boundary (every
4 rows/columns).
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

My Pengutronix address is not valid anymore, redirect people to the
Pengutronix kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The suspend scan rate value should not exceed 1000, unfortunately when
implementing the limit we used max_t instead of min_t, causing the value to
be at least 1000.
Signed-off-by: Dudley Du <dudl@cypress.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to Elan's firmware engineers we should not be subtracting 1 form
the raw number of x and y traces so that the pitch size is correct. For
example, if the touchpad x resolution is 2800 and x trace number is 20,
the pitch size of x should be 2800/20 = 140, not 2800/19 = 147.36.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When hover is detected report ABS_MT_DISTANCE as 1; for active contacts
the distance is reported as 0.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Let's zero-extend hardware id number when forming firmware file name,
to avoid kernel requesting firmware like "elants_i2c_   0.bin", which
is quite unexpected.

Acked-by: Charlie Mooney<charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Non interleaved dualpoint v2 devices have separate pointstick button bits,
document this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This change allows atmel_mxt_ts to bind to ACPI-enumerated devices in
Google Pixel 2 (2015).

While newer version of ACPI standard allow use of device-tree-like
properties in device descriptions, the version of ACPI implemented in
Google BIOS does not support them, and we have to resort to DMI data to
specify exact characteristics of the devices (touchpad vs. touchscreen,
GPIO to button mapping, etc).

Pixel 1 continues to use i2c devices and platform data created by
chromeos-laptop driver, since ACPI does not enumerate them.
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This adds rumble support for Xbox One controller by sending continuous
rumble command. Trigger button rumbling is not yet implemented.
Signed-off-by: Ming-ting Yao Wei <mwei@lxde.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Replace old pr_* with dev_* debugging macros
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

VMMouse enables low-latency mouse-cursor-movements for VMWare and QEMU
guests.  By removing the guest cursor and using the host as a guest cursor
the cursor movement appears instant although in reality there is some lag.
To be able to do this, the host's view of the cursor position must exactly
match the guest's view and an absolute pointer device is needed. Enter the
VMMouse. While the VMMouse driver has historically been an Xorg user-space
driver, implementing it as a kernel imput driver enables rootless Xorg and
new compositing display servers for VMware guests.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Get pressure format flag from firmware to check if we need to normalize
pressure data before reporting it.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

To save people some time let's document that we do not want new quirks for
"force-release" keys in the kernel and that they should patch userspace
(udev) instead.
Suggested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This change adds support for SS4 touchpad devices as ALPS_PROTO_V8
protocol.  They are real multi-touch devices and can be found in TOSHIBA
Tecra C50.
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In preparation for adding support for SS4 touchpads, let's split
alps_set_abs_params_mt into common, v7-specific, and other protocols
portions.
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Sync up with Linux 4.0-rc7 to bring in ALPS changes.

Pull networking fixes from David Miller:

 1) In TCP, don't register an FRTO for cumulatively ACK'd data that was
    previously SACK'd, from Neal Cardwell.

 2) Need to hold RNL mutex in ipv4 multicast code namespace cleanup,
    from Cong WANG.

 3) Similarly we have to hold RNL mutex for fib_rules_unregister(), also
    from Cong WANG.

 4) Revert and rework netns nsid allocation fix, from Nicolas Dichtel.

 5) When we encapsulate for a tunnel device, skb->sk still points to the
    user socket.  So this leads to cases where we retraverse the
    ipv4/ipv6 output path with skb->sk being of some other address
    family (f.e. AF_PACKET).  This can cause things to crash since the
    ipv4 output path is dereferencing an AF_PACKET socket as if it were
    an ipv4 one.

    The short term fix for 'net' and -stable is to elide these socket
    checks once we've entered an encapsulation sequence by testing
    xmit_recursion.

    Longer term we have a better solution wherein we pass the tunnel's
    socket down through the output paths, but that is way too invasive
    for 'net' and -stable.

    From Hannes Frederic Sowa.

 6) l2tp_init() failure path forgets to unregister per-net ops, from
    Cong WANG.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net/mlx4_core: Fix error message deprecation for ConnectX-2 cards
  net: dsa: fix filling routing table from OF description
  l2tp: unregister l2tp_net_ops on failure path
  mvneta: dont call mvneta_adjust_link() manually
  ipv6: protect skb->sk accesses from recursive dereference inside the stack
  netns: don't allocate an id for dead netns
  Revert "netns: don't clear nsid too early on removal"
  ip6mr: call del_timer_sync() in ip6mr_free_table()
  net: move fib_rules_unregister() under rtnl lock
  ipv4: take rtnl_lock and mark mrt table as freed on namespace cleanup
  tcp: fix FRTO undo on cumulative ACK of SACKed range
  xen-netfront: transmit fully GSO-sized packets

Commit 1daa4303 ("net/mlx4_core: Deprecate error message at
ConnectX-2 cards startup to debug") did the deprecation only for port 1
of the card. Need to deprecate for port 2 as well.

Fixes: 1daa4303 ("net/mlx4_core: Deprecate error message at ConnectX-2 cards startup to debug")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to description in 'include/net/dsa.h', in cascade switches
configurations where there are more than one interconnected devices,
'rtable' array in 'dsa_chip_data' structure is used to indicate which
port on this switch should be used to send packets to that are destined
for corresponding switch.

However, dsa_of_setup_routing_table() fills 'rtable' with port numbers
of the _target_ switch, but not current one.

This commit removes redundant devicetree parsing and adds needed port
number as a function argument. So dsa_of_setup_routing_table() now just
looks for target switch number by parsing parent of 'link' device node.

To remove possible misunderstandings with the way of determining target
switch number, a corresponding comment was added to the source code and
to the DSA device tree bindings documentation file.

This was tested on a custom board with two Marvell 88E6095 switches with
following corresponding routing tables: { -1, 10 } and { 8, -1 }.
Signed-off-by: Pavel Nakonechny <pavel.nakonechny@skitlab.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull input fixes from Dmitry Torokhov:
 "Updates for the input subsystem - two more tweaks for ALPS driver to
  work out kinks after splitting the touchpad, trackstick, and potential
  external PS/2 mouse into separate input devices.

  Changes to support ALPS SS4 devices (protocol V8) will be coming in
  4.1..."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: alps - document stick behavior for protocol V2
  Input: alps - report V2 Dualpoint Stick events via the right evdev node
  Input: alps - report interleaved bare PS/2 packets via dev3

Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the "linux,gpio-keymap" DT property is defined, the T19 keys are
configured and the device is setup as a touchpad rather than a touchscreen.
The logic is part of the input device initialization routine but it can be
factored out to its own function to simplify the former.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add support for the new T100 object which replaces the previous T9
multitouch touchscreen object in recent maXTouch devices. T100 provides
improved reporting with selectable auxiliary information, and a type field
for hover/stylus/glove reporting.

The hovering finger support was based on Chung-Yih's work in the ChromiumOS
downstream kernel:

https://chromium-review.googlesource.com/#/c/219280/Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
[javier: Factor out T9 and T100 init functions and rework hover support]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

mvneta_adjust_link() is a callback for of_phy_connect() and should
not be called directly. The result of calling it directly is as below:
Signed-off-by: David S. Miller <davem@davemloft.net>

We should not consult skb->sk for output decisions in xmit recursion
levels > 0 in the stack. Otherwise local socket settings could influence
the result of e.g. tunnel encapsulation process.

ipv6 does not conform with this in three places:

1) ip6_fragment: we do consult ipv6_npinfo for frag_size

2) sk_mc_loop in ipv6 uses skb->sk and checks if we should
   loop the packet back to the local socket

3) ip6_skb_dst_mtu could query the settings from the user socket and
   force a wrong MTU

Furthermore:
In sk_mc_loop we could potentially land in WARN_ON(1) if we use a
PF_PACKET socket ontop of an IPv6-backed vxlan device.

Reuse xmit_recursion as we are currently only interested in protecting
tunnel devices.

Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the comment right before explains, the keyboard state is to be cleared
only if the EC wasn't a wakeup source in the last suspend.

Without this commit, there's an unneeded delay when resuming from suspend
and we also lose the key that was pressed while suspended.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This driver does not use any PCI IDs, don't include the pci_ids.h header.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When slowly dropping 1, 2 and then 3 fingers on an image sensor touchpad,
we can see that the first finger gets reassigned a new slot while it did
not move. This is due to the kernel tracking algorithm which can not assign
correctly the 3 touches, being out of slots.

Declaring that we support 3 slots allows to actually forward:
slot 0 -> down, slot 1 -> up, slot 2 -> down
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Henrik Rydberg <rydberg@bitmath.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>