- 01 Dec, 2022 40 commits
-
-
Ryder Lee authored
Host triggered and catastrophic event triggered firmware core dumping for basic firmware issues triage, including state reporting, task/irq info, function calltrace and MCU memory dump. Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Ryder Lee authored
Trigger firmware crash and enable full system recovery through debugfs. This also renames knob "fw_ser" to a clear-cut name "sys_recovery". Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Bo Jiao authored
Add mt7915_reset() and refactor mt7915_mac_reset_work() to support full system recovery. Co-developed-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Bo Jiao <bo.jiao@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Bo Jiao authored
Reuse mt7915_dma_disable() to reduce duplicated code. This is a preliminary patch to enable full system reset. Co-developed-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Move aggregation stats array per-phy instead of share it between multiple interfaces. This is a preliminary patch to add mt7996 driver support. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
This is a preliminary patch to move aggr_stats array in mt76_phy structure. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Similar to mt7915, fix stats clash between bins [4-7] in 802.11 tx aggregation histogram. Fixes: 163f4d22 ("mt76: mt7921: add MAC support") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Fix stats clash between bins [4-7] in 802.11 tx aggregation histogram. Fixes: e57b7901 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Ryder Lee authored
This adds selectable RTC/CTS enablement for each interface. Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Ryder Lee authored
This adds selectable RTC/CTS enablement for each interface. Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Ming Yen Hsieh authored
Due to information missing, the firmware may be fail on bandwidth related settings in mt7921/mt7922. Add new cmd STA_REC_HE_V2 to apply additional capabilities in 6GHz band. Tested-by: Ben Greear <greearb@candelatech.com> Co-developed-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Ryder Lee authored
This reports signal strength of ACK packets from the peer as measured at each interface. Tested-by: Shurong Wen <shurong.wen@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Ryder Lee authored
The MIB INFO command is fetching MIB_BUSY_TIME, MIB_TX_TIME, MIB_RX_TIME and MIB_OBSS_AIRTIME from the radio and filling out cc_busy, cc_tx, cc_bss_rx and cc_rx respectively. busy should be >= tx + rx >= tx + bss_rx but we don’t always quite see this. Sometimes tx + rx is a bit higher than busy due to inaccurate accounting, so this patch recalculates numbers to make them more reasonable. Reported-By: Kevin Schneider <kevin.schneider@adtran.com> Tested-by: Kevin Schneider <kevin.schneider@adtran.com> Tested-by: Chad Monroe <chad.monroe@smartrg.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Ben Greear authored
This reverts commit f17f4864 and adds the MT_DRV_AMSDU_OFFLOAD flag for MT7921 USB/SDIO The reverted commit significantly decreases performance when running a test where two MT7915 radios have 16 station vdevs each, configured for AC mode, and transmitting UDP traffic to AP. Co-developed-by: Felix Fietkau <nbd@nbd.name> Reported-by: Carson Vandegriffe <carson.vandegriffe@candelatech.com> Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Enable WED tx support for mt7986-wmac chipset available on mt7986 board. Tested-by: Daniel Golle <daniel@makrotopia.org> Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com> Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
Introduce wed tx support for MT7986 chipset Tested-by: Daniel Golle <daniel@makrotopia.org> Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com> Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Lorenzo Bianconi authored
This is a preliminary patch to enable wed support for mt7986-wmac chipset. Tested-by: Daniel Golle <daniel@makrotopia.org> Co-developed-by: Bo Jiao <Bo.Jiao@mediatek.com> Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com> Co-developed-by: Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Ryder Lee authored
Correct mac timiing settings for different hardware generations. This improves 40-60Mbps performance. Fixes: 9aac2969 ("mt76: mt7915: update mac timing settings") Reported-By: Carson Vandegriffe <carson.vandegriffe@candelatech.com> Tested-by: Chad Monroe <chad.monroe@smartrg.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Shayne Chen authored
For MT7915D, correct antenna index should be set to let DFS radar detection work on the 5 GHz band. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Shayne Chen authored
In previous, we only allow user to configure tx antenna mask contiguously (e.g. 0x3, 0xf). This patch allows user to configure tx antenna mask interleavingly (e.g. 0x5, 0x8). By setting proper antenna mask and nss, user can prioritized the signal of different antennas, which helps to test their performance in normal mode. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Shayne Chen authored
Add mt76_connac_spe_idx() for antenna mask to spatial extension index conversion. This is used to support flexible control of tx antenna. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Shayne Chen authored
Let the configuration of testmode antenna mask on both band0 and band1 become antenna_mask rather than chainmask. This could simplify the settings for user and get rid of the conversion when sending fw command. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Peter Chiu authored
A variant of mt7916 supports up to 3 tx/rx paths but with only 2 spatial streams. An example usage of the 3rd path is to server as an auxiliary for beamforming. In order to deal with this case, this patch reworks some parts to correctly use paths or streams. Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Shayne Chen authored
Rework tx paths and streams init part to improve readability, and make sure that the available tx streams should be smaller than or equal to the available tx paths. Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Evelyn Tsai authored
The value of regidx of rf registers is combined with WF selection and offset. Extend the WF selection field from 4 to 8 bits since the adie index should also be specified. Signed-off-by: Evelyn Tsai <evelyn.tsai@mediatek.com> Signed-off-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Ben Greear authored
According to the tx-free-done documentation, the DW4 can be repeated, so have to be more careful about how we test for walking off the end of the array. Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Gaosheng Cui authored
All uses of mt76_wcid_mask_test() have been removed since commit 8950a62f ("mt76: get rid of mt76_wcid_hw routine"), so remove it. Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Sean Wang authored
Group 3 in RxD is disabled in monitor mode. We should use the group 5 in RxD instead to fix antenna signal way off issue, e.g we would see the incorrect antenna signal value in wireshark. On the other hand, Group 5 wouldn't be used in STA or AP mode, so the patch shouldn't cause any harm to those modes. Fixes: cbaa0a40 ("mt76: mt7921: fix up the monitor mode") Reported-by: Adrian Granados <agranados@gmail.com> Co-developed-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Felix Fietkau authored
- remove stbc, because mt76x0 doesn't support it and mt76x2 uses the same values as HT/VHT - reduce vht array to 2 elements, because VHT MCS0-7 are the same as HT Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Felix Fietkau authored
Its layout and code is mt76x02 specific Signed-off-by: Felix Fietkau <nbd@nbd.name>
-
Felix Fietkau authored
ieee80211_drop_unencrypted is called from ieee80211_rx_h_mesh_fwding and ieee80211_frame_allowed. Since ieee80211_rx_h_mesh_fwding can forward packets for other mesh nodes and is called earlier, it needs to check the decryptions status and if the packet is using the control protocol on its own, instead of deferring to the later call from ieee80211_frame_allowed. Because of that, ieee80211_drop_unencrypted has a mesh specific check that skips over the mesh header in order to check the payload protocol. This code is invalid when called from ieee80211_frame_allowed, since that happens after the 802.11->802.3 conversion. Fix this by moving the mesh specific check directly into ieee80211_rx_h_mesh_fwding. Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20221201135730.19723-1-nbd@nbd.nameSigned-off-by: Johannes Berg <johannes.berg@intel.com>
-
Felix Fietkau authored
This can be used to selectively disable feature flags for checksum offload, scatter/gather or GSO by changing vif->netdev_features. Removing features from vif->netdev_features does not affect the netdev features themselves, but instead fixes up skbs in the tx path so that the offloads are not needed in the driver. Aside from making it easier to deal with vif type based hardware limitations, this also makes it possible to optimize performance on hardware without native GSO support by declaring GSO support in hw->netdev_features and removing it from vif->netdev_features. This allows mac80211 to handle GSO segmentation after the sta lookup, but before itxq enqueue, thus reducing the number of unnecessary sta lookups, as well as some other per-packet processing. Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20221010094338.78070-1-nbd@nbd.nameSigned-off-by: Johannes Berg <johannes.berg@intel.com>
-
Kieran Frewen authored
Updates to the TIM information element to match changes made in the IEEE Std 802.11ah-2020. Signed-off-by: Kieran Frewen <kieran.frewen@morsemicro.com> Co-developed-by: Gilad Itzkovitch <gilad.itzkovitch@morsemicro.com> Signed-off-by: Gilad Itzkovitch <gilad.itzkovitch@morsemicro.com> Link: https://lore.kernel.org/r/20221106221602.25714-1-gilad.itzkovitch@morsemicro.com [use skb_put_data/skb_put_u8] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
It's not valid to have the multiple BSSID element in the association response (per 802.11 REVme D1.0), so don't try to parse it there, but only in the fallback beacon elements if needed. The other case that was parsing association requests was already changed in a previous commit. Change-Id: I659d2ef1253e079cc71c46a017044e116e31c024 Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
There's no need to open-code container_of() when we have bss_from_pub(). Use it. Change-Id: I074723717909ba211a40e6499f0c36df0e2ba4be Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
The call to ieee80211_do_stop() right after will also do synchronize_rcu() to ensure the SDATA_STATE_RUNNING bit is cleared, so we don't need to synchronize_net() here. Change-Id: Id9f9ffcf195002013e5d9fde288877d219780864 Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-
Alexander Wetzel authored
ieee80211_get_txq() can only be called with vif != NULL. Remove not needed NULL test in function. Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de> Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <error27@gmail.com> Link: https://lore.kernel.org/r/20221107161328.2883-1-alexander@wetzel-home.deSigned-off-by: Johannes Berg <johannes.berg@intel.com>
-
Chen Zhongjin authored
In regulatory_init_db(), when it's going to return a error, reg_pdev should be unregistered. When load_builtin_regdb_keys() fails it doesn't do it and makes cfg80211 can't be reload with report: sysfs: cannot create duplicate filename '/devices/platform/regulatory.0' ... <TASK> dump_stack_lvl+0x79/0x9b sysfs_warn_dup.cold+0x1c/0x29 sysfs_create_dir_ns+0x22d/0x290 kobject_add_internal+0x247/0x800 kobject_add+0x135/0x1b0 device_add+0x389/0x1be0 platform_device_add+0x28f/0x790 platform_device_register_full+0x376/0x4b0 regulatory_init+0x9a/0x4b2 [cfg80211] cfg80211_init+0x84/0x113 [cfg80211] ... Fixes: 90a53e44 ("cfg80211: implement regdb signature checking") Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com> Link: https://lore.kernel.org/r/20221109090237.214127-1-chenzhongjin@huawei.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>
-
JUN-KYU SHIN authored
If the "channel->freq_offset" comparison is omitted in cmp_bss(), BSS with different kHz units cannot be distinguished in the S1G Band. So "freq_offset" should also be included in the comparison. Signed-off-by: JUN-KYU SHIN <jk.shin@newratek.com> Link: https://lore.kernel.org/r/20221111023301.6395-1-jk.shin@newratek.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>
-
Íñigo Huguet authored
In ieee80211_lookup_key, the variable named `local` is unused if compiled without lockdep, getting this warning: net/mac80211/cfg.c: In function ‘ieee80211_lookup_key’: net/mac80211/cfg.c:542:26: error: unused variable ‘local’ [-Werror=unused-variable] struct ieee80211_local *local = sdata->local; ^~~~~ Fix it with __maybe_unused. Fixes: 8cbf0c2a ("wifi: mac80211: refactor some key code") Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Link: https://lore.kernel.org/r/20221111153622.29016-1-ihuguet@redhat.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>
-