- 20 Jun, 2017 19 commits
-
-
Xiang Chen authored
Add code to prepare internal abort command. Signed-off-by:
John Garry <john.garry@huawei.com> Signed-off-by:
Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Xiang Chen authored
Add code to itct setup and free for v3 hw. Signed-off-by:
-
Xiang Chen authored
Add code to prepare ATA frame for v3 hw Signed-off-by:
-
Xiang Chen authored
Add code to prepare SMP frame. Signed-off-by:
-
Xiang Chen authored
Add code to prepare SSP frame and deliver it to hardware. Signed-off-by:
-
Xiang Chen authored
Add v3 cq interrupt handler slot_complete_v3_hw(). Note: The slot error handling needs to be further refined in the future to examine all fields in the error record, and handle appropriately, instead of current solution - just report SAS_OPEN_REJECT. Signed-off-by:
-
Xiang Chen authored
Add code to initialise interrupts and add some interrupt handlers. Also add function hisi_sas_v3_destroy_irqs() to clean-up irqs upon module unloading. Signed-off-by:
-
Xiang Chen authored
Add code to configure PHYs for v3 hw. Signed-off-by:
-
Xiang Chen authored
Add code to initialise v3 hardware. Signed-off-by:
-
John Garry authored
Add the code to initialise the controller which is based on pci device in hisi_sas_v3_hw.c The core controller routines are still in hisi_sas_main.c; some common initialisation functions are also exported from hisi_sas_main.c For pci-based controller, the device properties, like phy count and sas address are read from the firmware, same as platform device-based controller. Signed-off-by:
-
John Garry authored
Add skeleton driver for v3 hw in hisi_sas_v3_hw.c File hisi_sas_v3_hw.c will serve 2 purposes: - probing and initialisation of the controller based on pci device - hw layer for v3-based controllers The controller design is quite similar to v2 hw in hip07. However key differences include: -All v2 hw bugs are fixed (hopefully), so workarounds are not required -support for device deregistration -some interrupt modifications -configurable max device support Signed-off-by:
-
John Garry authored
Move the functionality to retrieve the fw info into a dedicated device type-agnostic function, hisi_sas_get_fw_info(). The reasoning is that this function will be required for future pci-based platforms. Also add some debug logs for failure. Signed-off-by:
-
John Garry authored
Since hip08 SAS controller is based on pci device, add hisi_hba.pci_dev for hip08 (will be v3), and also rename hisi_hba.pdev to .platform_dev for clarity. In addition, for common code which wants to reference the controller device struct, add hisi_hba.dev, and change the common code to use it. Signed-off-by:
-
Xiang Chen authored
Relocate get_ncq_tag_v2_hw() to a common location, as future hw versions will require it. Also rename with "hisi_sas_" prefix for consistency. Signed-off-by:
-
Xiang Chen authored
Relocate get_ata_protocol() to a common location, as future hw versions will require it. Also rename with "hisi_sas_" prefix for consistency. Signed-off-by:
-
Xiang Chen authored
Relocate get_ata_protocol() to a common location, as future hw versions will require it. Also rename with "hisi_sas_" prefix for consistency. Signed-off-by:
-
Xiang Chen authored
Currently hisi_hba.lock is locked to deliver and receive a command to/from any hw queue. This causes much contention at high data-rates. To boost performance, lock on a per queue basis for sending and receiving commands to/from hw. Certain critical regions still need to be locked in the delivery and completion stages with hisi_hba.lock. New element hisi_sas_device.dq is added to store the delivery queue for a device, so it does not need to be needlessly re-calculated for every task. Signed-off-by:
-
John Garry authored
Currently hisi_sas_device.device_id is a u64. This can create a problem in selecting the queue for a device, in that this code does a 64b division on device id. For some 32b systems, 64b division is slow and the lib reference must be explicitly included. The device id does not need to be 64b in size, so, as a solution, just make as an int. Also, struct hisi_sas_device elements are re-ordered to improve packing efficiency. Signed-off-by:
-
Xiang Chen authored
We need to check for timeout before task status, or the task will be mistook as completed internal abort command. Also add protection for sas_task.task_state_flags in hisi_sas_tmf_timedout(). Signed-off-by:
-
- 13 Jun, 2017 21 commits
-
-
James Smart authored
Set lpfc driver revision to 11.4.0.0 Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <james.smart@broadcom.com> Signed-off-by:
-
James Smart authored
Administrator intervention is currently required to get good numbers when switching from running latency tests to IOPS tests. The configured interrupt coalescing values will greatly effect the results of these tests. Currently, the driver has a single coalescing value set by values of the module attribute. This patch changes the driver to support auto-configuration of the coalescing value based on the total number of outstanding IOs and average number of CQEs processed per interrupt for an EQ. Values are checked every 5 seconds. The driver defaults to the automatic selection. Automatic selection can be disabled by the new lpfc_auto_imax module_parameter. Older hardware can only change interrupt coalescing by mailbox command. Newer hardware supports change via a register. The patch support both. Signed-off-by:
-
James Smart authored
Addressed the following reported defects: ** CID 1411552: Control flow issues (MISSING_BREAK) /drivers/scsi/lpfc/lpfc_sli.c: 13259 in lpfc_sli4_nvmet_handle_rcqe() ** CID 1411553: Memory - illegal accesses (OVERRUN) /drivers/scsi/lpfc/lpfc_sli.c: 16218 in lpfc_fc_frame_check() ** CID 1411553: Memory - illegal accesses (OVERRUN) Overrunning array "lpfc_rctl_names" of 202 8-byte elements at element index 244 (byte offset 1952) using index "fc_hdr->fh_r_ctl" (which evaluates to 244). ** CID 1411554: Null pointer dereferences (REVERSE_INULL) /drivers/scsi/lpfc/lpfc_nvmet.c: 2131 in lpfc_nvmet_unsol_fcp_abort_cmp() ** CID 1411555: Memory - illegal accesses (UNINIT) /drivers/scsi/lpfc/lpfc_nvmet.c: 180 in lpfc_nvmet_ctxbuf_post() Signed-off-by:
-
James Smart authored
vports cannot login to target. For vports, lpfc_nodelist is allocated for targets only on completion of GFF_ID command. Driver checks if lpfc_nodelist exists for target before sending GFF_ID. So, GFF_ID and PLOGI are not sent. As mentioned by the comment in lpfc_prep_node_fc4type() routine, do not send GFF_ID only if this NPortID is previously identified as FCP target. Send GFF_ID if it is a newly identified remote port from GID_FT response. Signed-off-by:
-
James Smart authored
The nvmet driver was rejecting the initiator's PRLI because its reg_rpi for the PLOGI was still outstanding. The initiator would resend the PRLI without delay and get the same answer. The PRLI retries would exhaust causing the nvme initiator to set the nvmet ndlp to UNMAPPED. The driver's lpfc_els_retry handler did not have a policy for an LS_RJT with explanation CMD_IN_PROGRESS for PRLI or NVME_PRLI. This caused the delay to remain at 0 but retry set 1. Fix: When the ELS response is LS_RJT, TPC and the command was PRLI or NVME_PRLI, just set the delay to 1000 mS to get a 1 second delay on the PRLI retry. This was enough to allow the REG_RPI to complete at the target. Signed-off-by:
-
James Smart authored
Kernel panic when log_verbose is set to 0xffffffff phba->pport is dereferenced before it is initialized Fix: Do not dereference phba->pport if it is NULL Signed-off-by:
-
James Smart authored
System panic with general protection fault during driver load The driver uses a static array sli4_hba.handler_name to store the irq handler names. If the io_channel_irqs exceeds the pre-allocated size (32+1), then the driver will overwrite other fields of sli4_hba. Fix: Dynamically allocate handler_name. Signed-off-by:
-
James Smart authored
Null pointer dereference when BFS VM is powered off The driver incorrectly uses sli3_ring on SLI-4 adapters Use the correct ring structure based on sli_rev Signed-off-by:
Raphael Silva <raphasil@linux.vnet.ibm.com> Signed-off-by:
-
James Smart authored
On hbacmd reset failure, observing wrong string "nline" in kernel log. On failure, non negative value (1) is returned from sysfs store routine. It is interpreted as count by kernel and store routine is called again with the remaining characters as input. Fix: Return negative error code (-EIO) in case of failure. Signed-off-by:
-
James Smart authored
NVME FC counters don't reflect actual results Since counters are not atomic, or protected by a lock, the values often get screwed up. Make them atomic, like NVMET. Fix up sysfs and debugfs display accordingly Added Outstanding IOs to stats display Signed-off-by:
-
James Smart authored
Observing lpfc port down after issuing hbacmd reset command Failure in posting SGL buffers. If there is only one SGL buffer and rrq is valid for its XRI, we are rightly returning NULL but not adding the buffer back to the SGL list. So, number of buffers become less than total count and repost fails during reset. Add SGL buffer back to list before returning NULL. Signed-off-by:
-
James Smart authored
When unloading the driver, the NVMET driver would wait the full 30 seconds for its UNMAPPED initiator node to get removed before continuing with the unload process. NVMEI worked correctly. For each rport put into UNMAPPED or MAPPED state by NVMET, the driver puts a reference on the NDLP. The difference is that NVMEI has a unregister call for its rports and the extra reference is removed in the unregister process. For NVMET, the driver has to remove the reference explicitly when dropping out of UNMAPPED or MAPPED because there is no unregister call. Add a call to lpfc_nlp_put on the ndlp when NVMET and the old state was UNMAPPED or MAPPED. Signed-off-by:
-
James Smart authored
Lun Priority level shown as NA Remote port is not getting registered for nameserver and fdmi. Due to which dfc SendCTPassThru cmd is failing. Made changes to register the remote port for both. Signed-off-by:
-
James Smart authored
Inconsistent error messages and context state checks Context state sanity checks were not accurate or inconsistent in the code paths. Separated LS context states from FCP. Added and modified context state sanity checks. Use context state to determine if a sol or unsol ABORT is needed. Signed-off-by:
-
James Smart authored
While debugging Devloss and recovery, debugfs and sysfs were found to not show the NVME port roles consistently. The port role FC_PORT_ROLE_NVME_DISCOVERY was added with the devloss bringup and the other issues were just oversight. Add NVME Target and DISCSRVC to debugfs nodeinfo and sysfs nvme info handlers. The full port role was added to the NVME data only not the generic nodelist. Signed-off-by:
-
James Smart authored
As the devloss API was implemented in the nvmei driver, an evaluation of the nvme transport and the lpfc driver showed dual management of the rports. This creates a bug possibility when the thread count and SAN size increases. The nvmei driver code was based on a very early transport and was not revisited until the devloss API was introduced. Remove the listhead in the driver's rport data structure and the listhead in the driver's lport data structure. Remove all rport_list traversal. Convert the driver to use the nrport (nvme rport) pointer that is now NULL or nonNULL depending on a devloss action. Convert debugfs and nvme_info in sysfs to use the fc_nodes list in the vport. Signed-off-by:
-
James Smart authored
Add nvme initiator devloss support The existing implementation was based on no devloss behavior in the transport (e.g. immediate teardown) so code didn't properly handle delayed nvme rport device unregister calls. In addition, the driver was not correctly cycling the rport port role for each register-unregister-reregister process. This patch does the following: Rework the code to properly handle rport device unregister calls and potential re-allocation of the remoteport structure if the port comes back in under dev_loss_tmo. Correct code that was incorrectly cycling the rport port role for each register-unregister-reregister process. Prep the code to enable calling the nvme_fc transport api to dynamically update dev_loss_tmo when the scsi sysfs interface changes it. Memset the rpinfo structure in the registration call to enforce "accept nvme transport defaults" in the registration call. Driver parameters do influence the dev_loss_tmo transport setting dynamically. Simplifies the register function: the driver was incorrectly searching its local rport list to determine resume or new semantics, which is not valid as the transport already handles this. The rport was resumed if the rport handed back matches the ndlp->nrport pointer. Otherwise, devloss fired and the ndlp's nrport is NULL. Signed-off-by:
-
Christophe JAILLET authored
Merge some quoted strings to improve readability and to save some lines of code. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by:
Chad Dupuis <chad.dupuis@cavium.com> Signed-off-by:
-
Christophe JAILLET authored
Replace some 'dma_alloc_coherent+memset' by some quivalent 'dma_zalloc_coherent' in order to reduce code verbosity Signed-off-by:
-
Christophe JAILLET authored
We should return -ENOMEM in case of memory allocation error, as done elsewhere in this function. [mkp: fixed typo] Fixes: 61d8658b ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.") Signed-off-by:
-
Binoy Jayan authored
The semaphore 'fs_api_semaphore' is used as a simple mutex, so it should be written as one. Semaphores are going away in the future. Signed-off-by:
Binoy Jayan <binoy.jayan@linaro.org> Reviewed-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
