An error occurred fetching the project authors.
- 29 May, 2020 17 commits
-
-
Yan-Hsuan Chuang authored
For older versions of gcc, the array = {0}; will cause warnings: drivers/net/wireless/realtek/rtw88/rtw8822c.c: In function 'rtw8822c_power_trim': >> drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning: >> missing braces around initializer [-Wmissing-braces] s8 bb_gain[2][8] = {0}; ^ drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning: (near initialization for 'bb_gain[0]') [-Wmissing-braces] Fixes: 5ad4d895 ("rtw88: set power trim according to efuse PG values") Reported-by:kbuild test robot <lkp@intel.com> Signed-off-by:
Yan-Hsuan Chuang <yhchuang@realtek.com> Acked-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200522035521.12295-1-yhchuang@realtek.com
-
Ping-Ke Shih authored
Connecting to an AP with WPA2 security may fail. The IQK and the EAPOL 4-way handshake may overlap because the driver does IQK right after assoc success. For 802.11n devices, the IQK is done in the driver and it could require more than 100ms to complete. During IQK, any TX/RX events are paused. So if the EAPOL 4-way handshake started before IQK finished, then the 1/4 and 2/4 part of the handshake could be dropped. The AP will then issue deauth with reason IEEE8021X_FAILED (23). To resolve this, move IQK routine into managed TX prepare (ieee80211_ops::mgd_prepare_tx()). The callback is called before the managed frames (auth/assoc) are sent. This will make sure that the IQK is completed before the handshake starts. But don't do IQK during scanning because doing it on each channel will take too long. For 802.11ac devices, the IQK is done in firmware and it takes less time to complete. Therefore we don't see a failure during the EAPOL 4-way handshake. But it is still worth moving the IQK into ieee80211_ops::mgd_prepare_tx(). Fixes: f5df1a8b ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile") Tested-by:
You-Sheng Yang <vicamo.yang@canonical.com> Signed-off-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
Coex mechanism used to make BT have higher priority and more time to transfer data when BT inquiry-page, which leads to poor WiFi performance. Should take WiFi traffic into consideration. If the WiFi is having heavy traffic, use another parameter to make sure WiFi has more chance to TX/RX, while guarantee the priority of BT for inquiry. If the WiFi isn't busy (connected or not), set proper parameter to fix originals. Fixes: f5df1a8b ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile") Tested-by:
-
Ping-Ke Shih authored
Without setting antenna control owner, the WiFi could be disconnected if the BT has traffic. Because the antenna is switched to BT side for its traffic, and the WiFi will have no chance to transfer data. Set control owner to prevent WiFi disconnect issue. Fixes: f5df1a8b ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile") Tested-by:
-
Dinghao Liu authored
When wl12xx_cmd_role_disable() returns an error code, a pairing runtime PM usage counter decrement is needed to keep the counter balanced. Signed-off-by:
Dinghao Liu <dinghao.liu@zju.edu.cn> Acked-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Dinghao Liu authored
When wlcore_hw_interrupt_notify() returns an error code, a pairing runtime PM usage counter decrement is needed to keep the counter balanced. Signed-off-by:
-
Dinghao Liu authored
pm_runtime_get_sync() increments the runtime PM usage counter even the call returns an error code. Thus a pairing decrement is needed on the error handling path to keep the counter balanced. Signed-off-by:
-
Dinghao Liu authored
There are two error handling paths in this functon. When wlcore_tx_work_locked() returns an error code, we should decrease the runtime PM usage counter the same way as the error handling path beginning from pm_runtime_get_sync(). Signed-off-by:
-
Pascal Terjan authored
This is one of the 9 drivers redefining rfc1042_header. Signed-off-by:
Pascal Terjan <pterjan@google.com> Signed-off-by:
-
Pascal Terjan authored
This is one of the 9 drivers redefining rfc1042_header. Signed-off-by:
-
Pali Rohár authored
They are already present in linux/mmc/sdio_ids.h. Signed-off-by:
Pali Rohár <pali@kernel.org> Signed-off-by:
-
Larry Finger authored
Since the driver was first introduced into the kernel, it has only handled the ciphers associated with WEP, WPA, and WPA2. It fails with WPA3 even though mac80211 can handle those additional ciphers in software, b43legacy did not report that it could handle them. By setting MFP_CAPABLE using ieee80211_set_hw(), the problem is fixed. With this change, b43legacy will handle the ciphers it knows in hardware, and let mac80211 handle the others in software. It is not necessary to use the module parameter NOHWCRYPT to turn hardware encryption off. Although this change essentially eliminates that module parameter, I am choosing to keep it for cases where the hardware is broken, and software encryption is required for all ciphers. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Signed-off-by:
-
Larry Finger authored
Since the driver was first introduced into the kernel, it has only handled the ciphers associated with WEP, WPA, and WPA2. It fails with WPA3 even though mac80211 can handle those additional ciphers in software, b43 did not report that it could handle them. By setting MFP_CAPABLE using ieee80211_set_hw(), the problem is fixed. With this change, b43 will handle the ciphers it knows in hardware, and let mac80211 handle the others in software. It is not necessary to use the module parameter NOHWCRYPT to turn hardware encryption off. Although this change essentially eliminates that module parameter, I am choosing to keep it for cases where the hardware is broken, and software encryption is required for all ciphers. Reported-and-tested-by:
Rui Salvaterra <rsalvaterra@gmail.com> Signed-off-by:
-
Yan-Hsuan Chuang authored
This reverts commit 07d0f553. For rtw88 driver, the SDIO is going to be supported, so there is no need to remove the SDIO related power sequence settings. And while the power sequence parser will pass in the mask of the HCI, the SDIO part will not be used to set registers accordingly. Moreover, the power sequence table is released as a whole package, so the next time if we are going to update, the SDIO settings will be overwritten. So, revert this now. Signed-off-by:
-
Sergey Matyukevich authored
I am leaving Quantenna, so I will no longer have access to firmware and hardware. Meanwhile I plan to participate in reviewing qtnfmac patches for a while until my firmware knowledge becomes completely obsolete. Adding myself as a reviewer using my personal email address. Signed-off-by:
Sergey Matyukevich <sergey.matyukevich.os@quantenna.com> Signed-off-by:
Igor Mitsyanko <igor.mitsyanko.os@quantenna.com> Signed-off-by:
-
Rui Salvaterra authored
This gives us WPA3 support out of the box without having to manually disable hardware crypto. The driver will fall back to software crypto if the connection requires management frame protection. Suggested-by:
Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.8. Major changes: ath10k * SDIO and SNOC are not experimental anymore
-
- 27 May, 2020 23 commits
-
-
Jonas Falkevik authored
change typo in function name "nofity" to "notify" sctp_ulpevent_nofity_peer_addr_change -> sctp_ulpevent_notify_peer_addr_change Signed-off-by:
Jonas Falkevik <jonas.falkevik@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Tariq Toukan authored
This patch adds a field to the tls rx offload context which enables drivers to force a send_resync call. This field can be used by drivers to request a resync at the next possible tls record. It is beneficial for hardware that provides the resync sequence number asynchronously. In such cases, the packet that triggered the resync does not contain the information required for a resync. Instead, the driver requests resync for all the following TLS record until the asynchronous notification with the resync request TCP sequence arrives. A following series for mlx5e ConnectX-6DX TLS RX offload support will use this mechanism. Signed-off-by:
Boris Pismenny <borisp@mellanox.com> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Reviewed-by:
Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
David S. Miller authored
Cong Wang says: ==================== net_sched: reduce the number of qdisc resets This patchset aims to reduce the number of qdisc resets during qdisc tear down. Patch 1~3 are preparation for their following patches, especially patch 2 and patch 3 add a few tracepoints so that we can observe the whole lifetime of qdisc's. Patch 4 and patch 5 are the ones do the actual work. Please find more details in each patch description. Vaclav Zindulka tested this patchset and his large ruleset with over 13k qdiscs defined got from 22s to 520ms. ==================== Signed-off-by: -
Cong Wang authored
Resetting old qdisc on dev_queue->qdisc_sleeping in dev_qdisc_reset() is redundant, because this qdisc, even if not same with dev_queue->qdisc, is reset via qdisc_put() right after calling dev_graft_qdisc() when hitting refcnt 0. This is very easy to observe with qdisc_reset() tracepoint and stack traces. Reported-by:
Václav Zindulka <vaclav.zindulka@tlapnet.cz> Tested-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Cong Wang authored
Except for sch_mq and sch_mqprio, each dev queue points to the same root qdisc, so when we reset the dev queues with netdev_for_each_tx_queue() we end up resetting the same instance of the root qdisc for multiple times. Avoid this by checking the __QDISC_STATE_DEACTIVATED bit in each iteration, so for sch_mq/sch_mqprio, we still reset all of them like before, for the rest, we only reset it once. Reported-by:
-
Cong Wang authored
With this tracepoint, we could know when qdisc's are created, especially those default qdisc's. Sample output: tc-736 [001] ...1 56.230107: qdisc_create: dev=ens3 kind=pfifo parent=1:0 tc-736 [001] ...1 56.230113: qdisc_create: dev=ens3 kind=hfsc parent=ffff:ffff tc-738 [001] ...1 56.256816: qdisc_create: dev=ens3 kind=pfifo parent=1:100 tc-739 [001] ...1 56.267584: qdisc_create: dev=ens3 kind=pfifo parent=1:200 tc-740 [001] ...1 56.279649: qdisc_create: dev=ens3 kind=fq_codel parent=1:100 tc-741 [001] ...1 56.289996: qdisc_create: dev=ens3 kind=pfifo_fast parent=1:200 tc-745 [000] .N.1 111.687483: qdisc_create: dev=ens3 kind=ingress parent=ffff:fff1 Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
-
Cong Wang authored
Add two tracepoints for qdisc_reset() and qdisc_destroy() to track qdisc resetting and destroying. Sample output: tc-756 [000] ...3 138.355662: qdisc_reset: dev=ens3 kind=pfifo_fast parent=ffff:ffff handle=0:0 tc-756 [000] ...1 138.355720: qdisc_reset: dev=ens3 kind=pfifo_fast parent=ffff:ffff handle=0:0 tc-756 [000] ...1 138.355867: qdisc_reset: dev=ens3 kind=pfifo_fast parent=ffff:ffff handle=0:0 tc-756 [000] ...1 138.355930: qdisc_destroy: dev=ens3 kind=pfifo_fast parent=ffff:ffff handle=0:0 tc-757 [000] ...2 143.073780: qdisc_reset: dev=ens3 kind=fq_codel parent=ffff:ffff handle=8001:0 tc-757 [000] ...1 143.073878: qdisc_reset: dev=ens3 kind=fq_codel parent=ffff:ffff handle=8001:0 tc-757 [000] ...1 143.074114: qdisc_reset: dev=ens3 kind=fq_codel parent=ffff:ffff handle=8001:0 tc-757 [000] ...1 143.074228: qdisc_destroy: dev=ens3 kind=fq_codel parent=ffff:ffff handle=8001:0 Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
-
Cong Wang authored
qdisc_destroy() calls ops->reset() and cleans up qdisc->gso_skb and qdisc->skb_bad_txq, these are nearly same with qdisc_reset(), so just call it directly, and cosolidate the code for the next patch. Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
-
Wang Wenhu authored
No element named "client" exists within "struct ipa_endpoint". It might be a heritage forgotten to be removed. Delete it now. Signed-off-by:
Wang Wenhu <wenhu.wang@vivo.com> Signed-off-by:
-
Wang Wenhu authored
Change "transactio" -> "transaction". Also an alignment correction. Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== tcp: tcp_v4_err() cleanups This series is a followup of patch 23917494 ("tcp: tcp_v4_err() icmp skb is named icmp_skb"). Move the RFC 6069 code into a helper, and rename icmp_skb to standard skb name so that tcp_v4_err() and tcp_v6_err() are using consistent names. ==================== Signed-off-by:
-
Eric Dumazet authored
This essentially reverts 4d1a2d9e ("Revert Backoff [v3]: Rename skb to icmp_skb in tcp_v4_err()") Now we have tcp_ld_RTO_revert() helper, we can use the usual name for sk_buff parameter, so that tcp_v4_err() and tcp_v6_err() use similar names. Signed-off-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
-
Eric Dumazet authored
RFC 6069 logic has been implemented for IPv4 only so far, right in the middle of tcp_v4_err() and was error prone. Move this code to one helper, to make tcp_v4_err() more readable and to eventually expand RFC 6069 to IPv6 in the future. Also perform sock_owned_by_user() check a bit sooner. Signed-off-by:
-
David S. Miller authored
Huazhong Tan says: ==================== net: hns3: misc updates for -next This patchset includes some misc updates for the HNS3 ethernet driver. ==================== Signed-off-by: -
Huazhong Tan authored
When initializing CMDQ fails because of reset pending, there is no hint for debugging, so adds a log for it. Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
Yufeng Mo authored
Packets will not pass through MAC during app loopback. Therefore, it is meaningless to enable MAC while doing app loopback. This patch removes this unnecessary action. Signed-off-by:
Yufeng Mo <moyufeng@huawei.com> Signed-off-by:
-
Yufeng Mo authored
The HNS RDMA driver will support VF device later, whose re-initialization should be done after PF's. This patch changes the order of hclge_reset_prepare_up() and hclge_notify_roce_client(), so that PF's RoCE client will be reinitialized before VF's. Signed-off-by:
-
Guangbin Huang authored
To prevent from initializing VF NIC client in reset handling state, this patch adds resetting check in hclgevf_init_nic_client_instance(). Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
-
David S. Miller authored
Antoine Tenart says: ==================== net: mscc: allow forwarding ioctl operations to attached PHYs These two patches allow forwarding ioctl to the PHY MII implementation, and support is added for offloading timestamping operations to compatible attached PHYs. ==================== Signed-off-by: -
Antoine Tenart authored
This patch adds support for offloading timestamping operations not only to the Ocelot switch (as already supported) but to compatible PHYs. When both the PHY and the Ocelot switch support timestamping operations, the PHY implementation is chosen as the timestamp will happen closer to the medium. Signed-off-by:
Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Antoine Tenart authored
Allow ioctl to be implemented by the PHY, when a PHY is attached to the Ocelot switch. In case the ioctl is a request to set or get the hardware timestamp, use the Ocelot switch implementation for now. Signed-off-by:
-
Vladimir Oltean authored
The ocelot core library is written with the idea in mind that the VLAN table is populated by the bridge. Otherwise, not even a sane default pvid is provided: in standalone mode, the default pvid is 0, and the core expects the bridge layer to change it to 1. So without this patch, the VLAN table is completely empty at the end of the commands below, and traffic is broken as a result: ip link add dev br0 type bridge vlan_filtering 0 && ip link set dev br0 up for eth in $(ls /sys/bus/pci/devices/0000\:00\:00.5/net/); do ip link set dev $eth master br0 ip link set dev $eth up done ip link set dev br0 type bridge vlan_filtering 1 Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Stephen Worley authored
Add a couple large ecmp group nexthop selftests to cover the remnant fixed by d69100b8. The tests create 100 x32 ecmp groups of ipv4 and ipv6 and then dump them. On kernels without the fix, they will fail due to data remnant during the dump. Signed-off-by:
Stephen Worley <sworley@cumulusnetworks.com> Reviewed-by:
David Ahern <dsahern@gmail.com> Reviewed-by:
-
