- 05 Jan, 2022 40 commits
-
-
Russell King (Oracle) authored
The four RGMII interface modes take care of the required RGMII delay configuration at the PHY and should not be limited by the network MAC driver. Sadly, gemini was only permitting RGMII mode with no delays, which would require the required delay to be inserted via PCB tracking or by the MAC. However, there are designs that require the PHY to add the delay, which is impossible without Gemini permitting the other three PHY interface modes. Fix the driver to allow these. Signed-off-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Tested-by:
Corentin Labbe <clabbe.montjoie@gmail.com> Link: https://lore.kernel.org/r/E1n4mpT-002PLd-Ha@rmk-PC.armlinux.org.ukSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Jakub Kicinski authored
Russell King says: ==================== Fix RGMII delays for 88E1118 This series fixes the RGMII delays for 88E1118 Marvell PHYs, after a report by Corentin Labbe that the Marvell driver fails to work. Patch 1 cleans up the paged register accesses in m88e1118_config_init() and patch 2 adds the RGMII delay configuration. This comes with an element of risk as existing DT may need to be fixed for this in a similar way as we have done in the recent past for other PHY drivers that have misinterpreted the RGMII interface modes. ==================== Link: https://lore.kernel.org/r/YdR3wYFkm4eJApwb@shell.armlinux.org.ukSigned-off-by:
-
Russell King (Oracle) authored
Corentin Labbe reports that the SSI 1328 does not work when allowing the PHY to operate at gigabit speeds, but does work with the generic PHY driver. This appears to be because m88e1118_config_init() writes a fixed value to the MSCR register, claiming that this is to enable 1G speeds. However, this always sets bits 4 and 5, enabling RGMII transmit and receive delays. The suspicion is that the original board this was added for required the delays to make 1G speeds work. Add the necessary configuration for RGMII delays for the 88E1118 to bring this into line with the requirements for RGMII support, and thus make the SSI 1328 work. Corentin Labbe has tested this on gemini-ssi1328 and gemini-ns2502. Reported-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Russell King (Oracle) authored
Use phy_write_paged() in m88e1118_config_init() to set the MSCR value. We leave the other paged write for the LEDs in case the DT register parsing is relying on this page. Signed-off-by:
-
Eric Dumazet authored
As reported by Johannes, the tracker allocated in ethnl_default_notify() is not really needed, as this function is not expected to change a device reference count. Fixes: e4b89540 ("netlink: add net device refcount tracker to struct ethnl_req_info") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Johannes Berg <johannes@sipsolutions.net> Tested-by:
-
Eric Dumazet authored
qdisc_create() error path needs to use dev_put_track() because qdisc_alloc() allocated the tracker. Fixes: 606509f2 ("net/sched: add net device refcount tracker to struct Qdisc") Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== DSA cross-chip notifier cleanup This series deletes the no-op cross-chip notifier support for MRP and HSR, features which were introduced relatively recently and did not get full review at the time. The new code is functionally equivalent, but simpler. Cc: Horatiu Vultur <horatiu.vultur@microchip.com> Cc: George McCollister <george.mccollister@gmail.com> ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
The cross-chip notifiers for HSR are bypass operations, meaning that even though all switches in a tree are notified, only the switch specified in the info structure is targeted. We can eliminate the unnecessary complexity by deleting the cross-chip notifier logic and calling the ds->ops straight from port.c. Cc: George McCollister <george.mccollister@gmail.com> Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
George McCollister <george.mccollister@gmail.com> Signed-off-by:
-
Vladimir Oltean authored
The cross-chip notifiers for MRP are bypass operations, meaning that even though all switches in a tree are notified, only the switch specified in the info structure is targeted. We can eliminate the unnecessary complexity by deleting the cross-chip notifier logic and calling the ds->ops straight from port.c. Cc: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by:
-
Vladimir Oltean authored
The cross-chip notifier boilerplate code meant to check the presence of ds->ops->port_mrp_add_ring_role before calling it, but checked ds->ops->port_mrp_add instead, before calling ds->ops->port_mrp_add_ring_role. Therefore, a driver which implements one operation but not the other would trigger a NULL pointer dereference. There isn't any such driver in DSA yet, so there is no reason to backport the change. Issue found through code inspection. Cc: Horatiu Vultur <horatiu.vultur@microchip.com> Fixes: c595c433 ("net: dsa: add MRP support") Signed-off-by:
-
Danielle Ratson authored
Locally generated packets ingress the device through its CPU port. When the CPU port is congested and there are not enough credits in its headroom buffer, packets can be dropped. While this might be acceptable for data packets that traverse the network, configuration packets exchanged between the host and the device (EMADs) should not be subjected to this flow control. The "sdq_lp" bit in the SDQ (Send Descriptor Queue) context allows the host to instruct the device to treat packets sent on this queue as "local processing" and always process them, regardless of the state of the CPU port's headroom. Add the definition of this bit and set it for the dedicated SDQ reserved for the transmission of EMAD packets. This makes the "local processing" bit in the WQE (Work Queue Element) redundant, so clear it. Signed-off-by:
Danielle Ratson <danieller@nvidia.com> Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'linux-can-next-for-5.17-20220105' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2022-01-05 this is a pull request of 15 patches for net-next/master. The first patch is by me and removed an unused variable from the usb_8dev driver. Andy Shevchenko contributes a patch for the mcp251x driver, which removes an unneeded assignment. Jimmy Assarsson's patch for the kvaser_usb makes use of units.h in the assignment of frequencies. Lad Prabhakar provides 2 patches, converting the ti_hecc and the sja1000 driver to make use of platform_get_irq(). The 10 remaining patches are by Vincent Mailhol. First the etas_es58x driver populates the net_device::dev_port. The next 5 patches cleanup the handling of CAN error and CAN RTR messages of all drivers. The remaining 4 patches enhance the CAN controller mode flag handling and export it via netlink to user space. ==================== Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== Cleanup to main DSA structures This series contains changes that do the following: - struct dsa_port reduced from 576 to 544 bytes, and first cache line a bit better organized - struct dsa_switch from 160 to 136 bytes, and first cache line a bit better organized - struct dsa_switch_tree from 112 to 104 bytes, and first cache line a bit better organized ==================== Signed-off-by: -
Vladimir Oltean authored
There is a 7 byte hole after dst->setup and a 4 byte hole after dst->default_proto. Combining them, we have a single hole of just 3 bytes on 64 bit machines. Before: pahole -C dsa_switch_tree net/dsa/slave.o struct dsa_switch_tree { struct list_head list; /* 0 16 */ struct list_head ports; /* 16 16 */ struct raw_notifier_head nh; /* 32 8 */ unsigned int index; /* 40 4 */ struct kref refcount; /* 44 4 */ struct net_device * * lags; /* 48 8 */ bool setup; /* 56 1 */ /* XXX 7 bytes hole, try to pack */ /* --- cacheline 1 boundary (64 bytes) --- */ const struct dsa_device_ops * tag_ops; /* 64 8 */ enum dsa_tag_protocol default_proto; /* 72 4 */ /* XXX 4 bytes hole, try to pack */ struct dsa_platform_data * pd; /* 80 8 */ struct list_head rtable; /* 88 16 */ unsigned int lags_len; /* 104 4 */ unsigned int last_switch; /* 108 4 */ /* size: 112, cachelines: 2, members: 13 */ /* sum members: 101, holes: 2, sum holes: 11 */ /* last cacheline: 48 bytes */ }; After: pahole -C dsa_switch_tree net/dsa/slave.o struct dsa_switch_tree { struct list_head list; /* 0 16 */ struct list_head ports; /* 16 16 */ struct raw_notifier_head nh; /* 32 8 */ unsigned int index; /* 40 4 */ struct kref refcount; /* 44 4 */ struct net_device * * lags; /* 48 8 */ const struct dsa_device_ops * tag_ops; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */ enum dsa_tag_protocol default_proto; /* 64 4 */ bool setup; /* 68 1 */ /* XXX 3 bytes hole, try to pack */ struct dsa_platform_data * pd; /* 72 8 */ struct list_head rtable; /* 80 16 */ unsigned int lags_len; /* 96 4 */ unsigned int last_switch; /* 100 4 */ /* size: 104, cachelines: 2, members: 13 */ /* sum members: 101, holes: 1, sum holes: 3 */ /* last cacheline: 40 bytes */ }; Signed-off-by: -
Vladimir Oltean authored
dst->ports is accessed most notably by dsa_master_find_slave(), which is invoked in the RX path. dst->lags is accessed by dsa_lag_dev(), which is invoked in the RX path of tag_dsa.c. dst->tag_ops, dst->default_proto and dst->pd don't need to be in the first cache line, so they are moved out by this change. Before: pahole -C dsa_switch_tree net/dsa/slave.o struct dsa_switch_tree { struct list_head list; /* 0 16 */ struct raw_notifier_head nh; /* 16 8 */ unsigned int index; /* 24 4 */ struct kref refcount; /* 28 4 */ bool setup; /* 32 1 */ /* XXX 7 bytes hole, try to pack */ const struct dsa_device_ops * tag_ops; /* 40 8 */ enum dsa_tag_protocol default_proto; /* 48 4 */ /* XXX 4 bytes hole, try to pack */ struct dsa_platform_data * pd; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */ struct list_head ports; /* 64 16 */ struct list_head rtable; /* 80 16 */ struct net_device * * lags; /* 96 8 */ unsigned int lags_len; /* 104 4 */ unsigned int last_switch; /* 108 4 */ /* size: 112, cachelines: 2, members: 13 */ /* sum members: 101, holes: 2, sum holes: 11 */ /* last cacheline: 48 bytes */ }; After: pahole -C dsa_switch_tree net/dsa/slave.o struct dsa_switch_tree { struct list_head list; /* 0 16 */ struct list_head ports; /* 16 16 */ struct raw_notifier_head nh; /* 32 8 */ unsigned int index; /* 40 4 */ struct kref refcount; /* 44 4 */ struct net_device * * lags; /* 48 8 */ bool setup; /* 56 1 */ /* XXX 7 bytes hole, try to pack */ /* --- cacheline 1 boundary (64 bytes) --- */ const struct dsa_device_ops * tag_ops; /* 64 8 */ enum dsa_tag_protocol default_proto; /* 72 4 */ /* XXX 4 bytes hole, try to pack */ struct dsa_platform_data * pd; /* 80 8 */ struct list_head rtable; /* 88 16 */ unsigned int lags_len; /* 104 4 */ unsigned int last_switch; /* 108 4 */ /* size: 112, cachelines: 2, members: 13 */ /* sum members: 101, holes: 2, sum holes: 11 */ /* last cacheline: 48 bytes */ }; Signed-off-by: -
Vladimir Oltean authored
Currently, num_ports is declared as size_t, which is defined as __kernel_ulong_t, therefore it occupies 8 bytes of memory. Even switches with port numbers in the range of tens are exotic, so there is no need for this amount of storage. Additionally, because the max_num_bridges member right above it is also 4 bytes, it means the compiler needs to add padding between the last 2 fields. By reducing the size, we don't need that padding and can reduce the struct size. Before: pahole -C dsa_switch net/dsa/slave.o struct dsa_switch { struct device * dev; /* 0 8 */ struct dsa_switch_tree * dst; /* 8 8 */ unsigned int index; /* 16 4 */ u32 setup:1; /* 20: 0 4 */ u32 vlan_filtering_is_global:1; /* 20: 1 4 */ u32 needs_standalone_vlan_filtering:1; /* 20: 2 4 */ u32 configure_vlan_while_not_filtering:1; /* 20: 3 4 */ u32 untag_bridge_pvid:1; /* 20: 4 4 */ u32 assisted_learning_on_cpu_port:1; /* 20: 5 4 */ u32 vlan_filtering:1; /* 20: 6 4 */ u32 pcs_poll:1; /* 20: 7 4 */ u32 mtu_enforcement_ingress:1; /* 20: 8 4 */ /* XXX 23 bits hole, try to pack */ struct notifier_block nb; /* 24 24 */ /* XXX last struct has 4 bytes of padding */ void * priv; /* 48 8 */ void * tagger_data; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */ struct dsa_chip_data * cd; /* 64 8 */ const struct dsa_switch_ops * ops; /* 72 8 */ u32 phys_mii_mask; /* 80 4 */ /* XXX 4 bytes hole, try to pack */ struct mii_bus * slave_mii_bus; /* 88 8 */ unsigned int ageing_time_min; /* 96 4 */ unsigned int ageing_time_max; /* 100 4 */ struct dsa_8021q_context * tag_8021q_ctx; /* 104 8 */ struct devlink * devlink; /* 112 8 */ unsigned int num_tx_queues; /* 120 4 */ unsigned int num_lag_ids; /* 124 4 */ /* --- cacheline 2 boundary (128 bytes) --- */ unsigned int max_num_bridges; /* 128 4 */ /* XXX 4 bytes hole, try to pack */ size_t num_ports; /* 136 8 */ /* size: 144, cachelines: 3, members: 27 */ /* sum members: 132, holes: 2, sum holes: 8 */ /* sum bitfield members: 9 bits, bit holes: 1, sum bit holes: 23 bits */ /* paddings: 1, sum paddings: 4 */ /* last cacheline: 16 bytes */ }; After: pahole -C dsa_switch net/dsa/slave.o struct dsa_switch { struct device * dev; /* 0 8 */ struct dsa_switch_tree * dst; /* 8 8 */ unsigned int index; /* 16 4 */ u32 setup:1; /* 20: 0 4 */ u32 vlan_filtering_is_global:1; /* 20: 1 4 */ u32 needs_standalone_vlan_filtering:1; /* 20: 2 4 */ u32 configure_vlan_while_not_filtering:1; /* 20: 3 4 */ u32 untag_bridge_pvid:1; /* 20: 4 4 */ u32 assisted_learning_on_cpu_port:1; /* 20: 5 4 */ u32 vlan_filtering:1; /* 20: 6 4 */ u32 pcs_poll:1; /* 20: 7 4 */ u32 mtu_enforcement_ingress:1; /* 20: 8 4 */ /* XXX 23 bits hole, try to pack */ struct notifier_block nb; /* 24 24 */ /* XXX last struct has 4 bytes of padding */ void * priv; /* 48 8 */ void * tagger_data; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */ struct dsa_chip_data * cd; /* 64 8 */ const struct dsa_switch_ops * ops; /* 72 8 */ u32 phys_mii_mask; /* 80 4 */ /* XXX 4 bytes hole, try to pack */ struct mii_bus * slave_mii_bus; /* 88 8 */ unsigned int ageing_time_min; /* 96 4 */ unsigned int ageing_time_max; /* 100 4 */ struct dsa_8021q_context * tag_8021q_ctx; /* 104 8 */ struct devlink * devlink; /* 112 8 */ unsigned int num_tx_queues; /* 120 4 */ unsigned int num_lag_ids; /* 124 4 */ /* --- cacheline 2 boundary (128 bytes) --- */ unsigned int max_num_bridges; /* 128 4 */ unsigned int num_ports; /* 132 4 */ /* size: 136, cachelines: 3, members: 27 */ /* sum members: 128, holes: 1, sum holes: 4 */ /* sum bitfield members: 9 bits, bit holes: 1, sum bit holes: 23 bits */ /* paddings: 1, sum paddings: 4 */ /* last cacheline: 8 bytes */ }; Signed-off-by: -
Vladimir Oltean authored
struct dsa_switch has 9 boolean properties, many of which are in fact set by drivers for custom behavior (vlan_filtering_is_global, needs_standalone_vlan_filtering, etc etc). The binary layout of the structure could be improved. For example, the "bool setup" at the beginning introduces a gratuitous 7 byte hole in the first cache line. The change merges all boolean properties into bitfields of an u32, and places that u32 in the first cache line of the structure, since many bools are accessed from the data path (untag_bridge_pvid, vlan_filtering, vlan_filtering_is_global). We place this u32 after the existing ds->index, which is also 4 bytes in size. As a positive side effect, ds->tagger_data now fits into the first cache line too, because 4 bytes are saved. Before: pahole -C dsa_switch net/dsa/slave.o struct dsa_switch { bool setup; /* 0 1 */ /* XXX 7 bytes hole, try to pack */ struct device * dev; /* 8 8 */ struct dsa_switch_tree * dst; /* 16 8 */ unsigned int index; /* 24 4 */ /* XXX 4 bytes hole, try to pack */ struct notifier_block nb; /* 32 24 */ /* XXX last struct has 4 bytes of padding */ void * priv; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */ void * tagger_data; /* 64 8 */ struct dsa_chip_data * cd; /* 72 8 */ const struct dsa_switch_ops * ops; /* 80 8 */ u32 phys_mii_mask; /* 88 4 */ /* XXX 4 bytes hole, try to pack */ struct mii_bus * slave_mii_bus; /* 96 8 */ unsigned int ageing_time_min; /* 104 4 */ unsigned int ageing_time_max; /* 108 4 */ struct dsa_8021q_context * tag_8021q_ctx; /* 112 8 */ struct devlink * devlink; /* 120 8 */ /* --- cacheline 2 boundary (128 bytes) --- */ unsigned int num_tx_queues; /* 128 4 */ bool vlan_filtering_is_global; /* 132 1 */ bool needs_standalone_vlan_filtering; /* 133 1 */ bool configure_vlan_while_not_filtering; /* 134 1 */ bool untag_bridge_pvid; /* 135 1 */ bool assisted_learning_on_cpu_port; /* 136 1 */ bool vlan_filtering; /* 137 1 */ bool pcs_poll; /* 138 1 */ bool mtu_enforcement_ingress; /* 139 1 */ unsigned int num_lag_ids; /* 140 4 */ unsigned int max_num_bridges; /* 144 4 */ /* XXX 4 bytes hole, try to pack */ size_t num_ports; /* 152 8 */ /* size: 160, cachelines: 3, members: 27 */ /* sum members: 141, holes: 4, sum holes: 19 */ /* paddings: 1, sum paddings: 4 */ /* last cacheline: 32 bytes */ }; After: pahole -C dsa_switch net/dsa/slave.o struct dsa_switch { struct device * dev; /* 0 8 */ struct dsa_switch_tree * dst; /* 8 8 */ unsigned int index; /* 16 4 */ u32 setup:1; /* 20: 0 4 */ u32 vlan_filtering_is_global:1; /* 20: 1 4 */ u32 needs_standalone_vlan_filtering:1; /* 20: 2 4 */ u32 configure_vlan_while_not_filtering:1; /* 20: 3 4 */ u32 untag_bridge_pvid:1; /* 20: 4 4 */ u32 assisted_learning_on_cpu_port:1; /* 20: 5 4 */ u32 vlan_filtering:1; /* 20: 6 4 */ u32 pcs_poll:1; /* 20: 7 4 */ u32 mtu_enforcement_ingress:1; /* 20: 8 4 */ /* XXX 23 bits hole, try to pack */ struct notifier_block nb; /* 24 24 */ /* XXX last struct has 4 bytes of padding */ void * priv; /* 48 8 */ void * tagger_data; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */ struct dsa_chip_data * cd; /* 64 8 */ const struct dsa_switch_ops * ops; /* 72 8 */ u32 phys_mii_mask; /* 80 4 */ /* XXX 4 bytes hole, try to pack */ struct mii_bus * slave_mii_bus; /* 88 8 */ unsigned int ageing_time_min; /* 96 4 */ unsigned int ageing_time_max; /* 100 4 */ struct dsa_8021q_context * tag_8021q_ctx; /* 104 8 */ struct devlink * devlink; /* 112 8 */ unsigned int num_tx_queues; /* 120 4 */ unsigned int num_lag_ids; /* 124 4 */ /* --- cacheline 2 boundary (128 bytes) --- */ unsigned int max_num_bridges; /* 128 4 */ /* XXX 4 bytes hole, try to pack */ size_t num_ports; /* 136 8 */ /* size: 144, cachelines: 3, members: 27 */ /* sum members: 132, holes: 2, sum holes: 8 */ /* sum bitfield members: 9 bits, bit holes: 1, sum bit holes: 23 bits */ /* paddings: 1, sum paddings: 4 */ /* last cacheline: 16 bytes */ }; Signed-off-by: -
Vladimir Oltean authored
Both dsa_port :: type and dsa_port :: index introduce a 4 octet hole after them, so we can group them together and the holes would be eliminated, turning 16 octets of storage into just 8. This makes the cpu_dp pointer fit in the first cache line, which is good, because dsa_slave_to_master(), called by dsa_enqueue_skb(), uses it. Before: pahole -C dsa_port net/dsa/slave.o struct dsa_port { union { struct net_device * master; /* 0 8 */ struct net_device * slave; /* 0 8 */ }; /* 0 8 */ const struct dsa_device_ops * tag_ops; /* 8 8 */ struct dsa_switch_tree * dst; /* 16 8 */ struct sk_buff * (*rcv)(struct sk_buff *, struct net_device *); /* 24 8 */ enum { DSA_PORT_TYPE_UNUSED = 0, DSA_PORT_TYPE_CPU = 1, DSA_PORT_TYPE_DSA = 2, DSA_PORT_TYPE_USER = 3, } type; /* 32 4 */ /* XXX 4 bytes hole, try to pack */ struct dsa_switch * ds; /* 40 8 */ unsigned int index; /* 48 4 */ /* XXX 4 bytes hole, try to pack */ const char * name; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */ struct dsa_port * cpu_dp; /* 64 8 */ u8 mac[6]; /* 72 6 */ u8 stp_state; /* 78 1 */ u8 vlan_filtering:1; /* 79: 0 1 */ u8 learning:1; /* 79: 1 1 */ u8 lag_tx_enabled:1; /* 79: 2 1 */ u8 devlink_port_setup:1; /* 79: 3 1 */ u8 setup:1; /* 79: 4 1 */ /* XXX 3 bits hole, try to pack */ struct device_node * dn; /* 80 8 */ unsigned int ageing_time; /* 88 4 */ /* XXX 4 bytes hole, try to pack */ struct dsa_bridge * bridge; /* 96 8 */ struct devlink_port devlink_port; /* 104 288 */ /* --- cacheline 6 boundary (384 bytes) was 8 bytes ago --- */ struct phylink * pl; /* 392 8 */ struct phylink_config pl_config; /* 400 40 */ struct net_device * lag_dev; /* 440 8 */ /* --- cacheline 7 boundary (448 bytes) --- */ struct net_device * hsr_dev; /* 448 8 */ struct list_head list; /* 456 16 */ const struct ethtool_ops * orig_ethtool_ops; /* 472 8 */ const struct dsa_netdevice_ops * netdev_ops; /* 480 8 */ struct mutex addr_lists_lock; /* 488 32 */ /* --- cacheline 8 boundary (512 bytes) was 8 bytes ago --- */ struct list_head fdbs; /* 520 16 */ struct list_head mdbs; /* 536 16 */ /* size: 552, cachelines: 9, members: 30 */ /* sum members: 539, holes: 3, sum holes: 12 */ /* sum bitfield members: 5 bits, bit holes: 1, sum bit holes: 3 bits */ /* last cacheline: 40 bytes */ }; After: pahole -C dsa_port net/dsa/slave.o struct dsa_port { union { struct net_device * master; /* 0 8 */ struct net_device * slave; /* 0 8 */ }; /* 0 8 */ const struct dsa_device_ops * tag_ops; /* 8 8 */ struct dsa_switch_tree * dst; /* 16 8 */ struct sk_buff * (*rcv)(struct sk_buff *, struct net_device *); /* 24 8 */ struct dsa_switch * ds; /* 32 8 */ unsigned int index; /* 40 4 */ enum { DSA_PORT_TYPE_UNUSED = 0, DSA_PORT_TYPE_CPU = 1, DSA_PORT_TYPE_DSA = 2, DSA_PORT_TYPE_USER = 3, } type; /* 44 4 */ const char * name; /* 48 8 */ struct dsa_port * cpu_dp; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */ u8 mac[6]; /* 64 6 */ u8 stp_state; /* 70 1 */ u8 vlan_filtering:1; /* 71: 0 1 */ u8 learning:1; /* 71: 1 1 */ u8 lag_tx_enabled:1; /* 71: 2 1 */ u8 devlink_port_setup:1; /* 71: 3 1 */ u8 setup:1; /* 71: 4 1 */ /* XXX 3 bits hole, try to pack */ struct device_node * dn; /* 72 8 */ unsigned int ageing_time; /* 80 4 */ /* XXX 4 bytes hole, try to pack */ struct dsa_bridge * bridge; /* 88 8 */ struct devlink_port devlink_port; /* 96 288 */ /* --- cacheline 6 boundary (384 bytes) --- */ struct phylink * pl; /* 384 8 */ struct phylink_config pl_config; /* 392 40 */ struct net_device * lag_dev; /* 432 8 */ struct net_device * hsr_dev; /* 440 8 */ /* --- cacheline 7 boundary (448 bytes) --- */ struct list_head list; /* 448 16 */ const struct ethtool_ops * orig_ethtool_ops; /* 464 8 */ const struct dsa_netdevice_ops * netdev_ops; /* 472 8 */ struct mutex addr_lists_lock; /* 480 32 */ /* --- cacheline 8 boundary (512 bytes) --- */ struct list_head fdbs; /* 512 16 */ struct list_head mdbs; /* 528 16 */ /* size: 544, cachelines: 9, members: 30 */ /* sum members: 539, holes: 1, sum holes: 4 */ /* sum bitfield members: 5 bits, bit holes: 1, sum bit holes: 3 bits */ /* last cacheline: 32 bytes */ }; Signed-off-by: -
Vladimir Oltean authored
struct dsa_port has 5 bool members which create quite a number of 7 byte holes in the structure layout. By merging them all into bitfields of an u8, and placing that u8 in the 1-byte hole after dp->mac and dp->stp_state, we can reduce the structure size from 576 bytes to 552 bytes on arm64. Before: pahole -C dsa_port net/dsa/slave.o struct dsa_port { union { struct net_device * master; /* 0 8 */ struct net_device * slave; /* 0 8 */ }; /* 0 8 */ const struct dsa_device_ops * tag_ops; /* 8 8 */ struct dsa_switch_tree * dst; /* 16 8 */ struct sk_buff * (*rcv)(struct sk_buff *, struct net_device *); /* 24 8 */ enum { DSA_PORT_TYPE_UNUSED = 0, DSA_PORT_TYPE_CPU = 1, DSA_PORT_TYPE_DSA = 2, DSA_PORT_TYPE_USER = 3, } type; /* 32 4 */ /* XXX 4 bytes hole, try to pack */ struct dsa_switch * ds; /* 40 8 */ unsigned int index; /* 48 4 */ /* XXX 4 bytes hole, try to pack */ const char * name; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */ struct dsa_port * cpu_dp; /* 64 8 */ u8 mac[6]; /* 72 6 */ u8 stp_state; /* 78 1 */ /* XXX 1 byte hole, try to pack */ struct device_node * dn; /* 80 8 */ unsigned int ageing_time; /* 88 4 */ bool vlan_filtering; /* 92 1 */ bool learning; /* 93 1 */ /* XXX 2 bytes hole, try to pack */ struct dsa_bridge * bridge; /* 96 8 */ struct devlink_port devlink_port; /* 104 288 */ /* --- cacheline 6 boundary (384 bytes) was 8 bytes ago --- */ bool devlink_port_setup; /* 392 1 */ /* XXX 7 bytes hole, try to pack */ struct phylink * pl; /* 400 8 */ struct phylink_config pl_config; /* 408 40 */ /* --- cacheline 7 boundary (448 bytes) --- */ struct net_device * lag_dev; /* 448 8 */ bool lag_tx_enabled; /* 456 1 */ /* XXX 7 bytes hole, try to pack */ struct net_device * hsr_dev; /* 464 8 */ struct list_head list; /* 472 16 */ const struct ethtool_ops * orig_ethtool_ops; /* 488 8 */ const struct dsa_netdevice_ops * netdev_ops; /* 496 8 */ struct mutex addr_lists_lock; /* 504 32 */ /* --- cacheline 8 boundary (512 bytes) was 24 bytes ago --- */ struct list_head fdbs; /* 536 16 */ struct list_head mdbs; /* 552 16 */ bool setup; /* 568 1 */ /* size: 576, cachelines: 9, members: 30 */ /* sum members: 544, holes: 6, sum holes: 25 */ /* padding: 7 */ }; After: pahole -C dsa_port net/dsa/slave.o struct dsa_port { union { struct net_device * master; /* 0 8 */ struct net_device * slave; /* 0 8 */ }; /* 0 8 */ const struct dsa_device_ops * tag_ops; /* 8 8 */ struct dsa_switch_tree * dst; /* 16 8 */ struct sk_buff * (*rcv)(struct sk_buff *, struct net_device *); /* 24 8 */ enum { DSA_PORT_TYPE_UNUSED = 0, DSA_PORT_TYPE_CPU = 1, DSA_PORT_TYPE_DSA = 2, DSA_PORT_TYPE_USER = 3, } type; /* 32 4 */ /* XXX 4 bytes hole, try to pack */ struct dsa_switch * ds; /* 40 8 */ unsigned int index; /* 48 4 */ /* XXX 4 bytes hole, try to pack */ const char * name; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */ struct dsa_port * cpu_dp; /* 64 8 */ u8 mac[6]; /* 72 6 */ u8 stp_state; /* 78 1 */ u8 vlan_filtering:1; /* 79: 0 1 */ u8 learning:1; /* 79: 1 1 */ u8 lag_tx_enabled:1; /* 79: 2 1 */ u8 devlink_port_setup:1; /* 79: 3 1 */ u8 setup:1; /* 79: 4 1 */ /* XXX 3 bits hole, try to pack */ struct device_node * dn; /* 80 8 */ unsigned int ageing_time; /* 88 4 */ /* XXX 4 bytes hole, try to pack */ struct dsa_bridge * bridge; /* 96 8 */ struct devlink_port devlink_port; /* 104 288 */ /* --- cacheline 6 boundary (384 bytes) was 8 bytes ago --- */ struct phylink * pl; /* 392 8 */ struct phylink_config pl_config; /* 400 40 */ struct net_device * lag_dev; /* 440 8 */ /* --- cacheline 7 boundary (448 bytes) --- */ struct net_device * hsr_dev; /* 448 8 */ struct list_head list; /* 456 16 */ const struct ethtool_ops * orig_ethtool_ops; /* 472 8 */ const struct dsa_netdevice_ops * netdev_ops; /* 480 8 */ struct mutex addr_lists_lock; /* 488 32 */ /* --- cacheline 8 boundary (512 bytes) was 8 bytes ago --- */ struct list_head fdbs; /* 520 16 */ struct list_head mdbs; /* 536 16 */ /* size: 552, cachelines: 9, members: 30 */ /* sum members: 539, holes: 3, sum holes: 12 */ /* sum bitfield members: 5 bits, bit holes: 1, sum bit holes: 3 bits */ /* last cacheline: 40 bytes */ }; Signed-off-by: -
Vladimir Oltean authored
The MAC address of a port is 6 octets in size, and this creates a 2 octet hole after it. There are some other u8 members of struct dsa_port that we can put in that hole. One such member is the stp_state. Before: pahole -C dsa_port net/dsa/slave.o struct dsa_port { union { struct net_device * master; /* 0 8 */ struct net_device * slave; /* 0 8 */ }; /* 0 8 */ const struct dsa_device_ops * tag_ops; /* 8 8 */ struct dsa_switch_tree * dst; /* 16 8 */ struct sk_buff * (*rcv)(struct sk_buff *, struct net_device *); /* 24 8 */ enum { DSA_PORT_TYPE_UNUSED = 0, DSA_PORT_TYPE_CPU = 1, DSA_PORT_TYPE_DSA = 2, DSA_PORT_TYPE_USER = 3, } type; /* 32 4 */ /* XXX 4 bytes hole, try to pack */ struct dsa_switch * ds; /* 40 8 */ unsigned int index; /* 48 4 */ /* XXX 4 bytes hole, try to pack */ const char * name; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */ struct dsa_port * cpu_dp; /* 64 8 */ u8 mac[6]; /* 72 6 */ /* XXX 2 bytes hole, try to pack */ struct device_node * dn; /* 80 8 */ unsigned int ageing_time; /* 88 4 */ bool vlan_filtering; /* 92 1 */ bool learning; /* 93 1 */ u8 stp_state; /* 94 1 */ /* XXX 1 byte hole, try to pack */ struct dsa_bridge * bridge; /* 96 8 */ struct devlink_port devlink_port; /* 104 288 */ /* --- cacheline 6 boundary (384 bytes) was 8 bytes ago --- */ bool devlink_port_setup; /* 392 1 */ /* XXX 7 bytes hole, try to pack */ struct phylink * pl; /* 400 8 */ struct phylink_config pl_config; /* 408 40 */ /* --- cacheline 7 boundary (448 bytes) --- */ struct net_device * lag_dev; /* 448 8 */ bool lag_tx_enabled; /* 456 1 */ /* XXX 7 bytes hole, try to pack */ struct net_device * hsr_dev; /* 464 8 */ struct list_head list; /* 472 16 */ const struct ethtool_ops * orig_ethtool_ops; /* 488 8 */ const struct dsa_netdevice_ops * netdev_ops; /* 496 8 */ struct mutex addr_lists_lock; /* 504 32 */ /* --- cacheline 8 boundary (512 bytes) was 24 bytes ago --- */ struct list_head fdbs; /* 536 16 */ struct list_head mdbs; /* 552 16 */ bool setup; /* 568 1 */ /* size: 576, cachelines: 9, members: 30 */ /* sum members: 544, holes: 6, sum holes: 25 */ /* padding: 7 */ }; After: pahole -C dsa_port net/dsa/slave.o struct dsa_port { union { struct net_device * master; /* 0 8 */ struct net_device * slave; /* 0 8 */ }; /* 0 8 */ const struct dsa_device_ops * tag_ops; /* 8 8 */ struct dsa_switch_tree * dst; /* 16 8 */ struct sk_buff * (*rcv)(struct sk_buff *, struct net_device *); /* 24 8 */ enum { DSA_PORT_TYPE_UNUSED = 0, DSA_PORT_TYPE_CPU = 1, DSA_PORT_TYPE_DSA = 2, DSA_PORT_TYPE_USER = 3, } type; /* 32 4 */ /* XXX 4 bytes hole, try to pack */ struct dsa_switch * ds; /* 40 8 */ unsigned int index; /* 48 4 */ /* XXX 4 bytes hole, try to pack */ const char * name; /* 56 8 */ /* --- cacheline 1 boundary (64 bytes) --- */ struct dsa_port * cpu_dp; /* 64 8 */ u8 mac[6]; /* 72 6 */ u8 stp_state; /* 78 1 */ /* XXX 1 byte hole, try to pack */ struct device_node * dn; /* 80 8 */ unsigned int ageing_time; /* 88 4 */ bool vlan_filtering; /* 92 1 */ bool learning; /* 93 1 */ /* XXX 2 bytes hole, try to pack */ struct dsa_bridge * bridge; /* 96 8 */ struct devlink_port devlink_port; /* 104 288 */ /* --- cacheline 6 boundary (384 bytes) was 8 bytes ago --- */ bool devlink_port_setup; /* 392 1 */ /* XXX 7 bytes hole, try to pack */ struct phylink * pl; /* 400 8 */ struct phylink_config pl_config; /* 408 40 */ /* --- cacheline 7 boundary (448 bytes) --- */ struct net_device * lag_dev; /* 448 8 */ bool lag_tx_enabled; /* 456 1 */ /* XXX 7 bytes hole, try to pack */ struct net_device * hsr_dev; /* 464 8 */ struct list_head list; /* 472 16 */ const struct ethtool_ops * orig_ethtool_ops; /* 488 8 */ const struct dsa_netdevice_ops * netdev_ops; /* 496 8 */ struct mutex addr_lists_lock; /* 504 32 */ /* --- cacheline 8 boundary (512 bytes) was 24 bytes ago --- */ struct list_head fdbs; /* 536 16 */ struct list_head mdbs; /* 552 16 */ bool setup; /* 568 1 */ /* size: 576, cachelines: 9, members: 30 */ /* sum members: 544, holes: 6, sum holes: 25 */ /* padding: 7 */ }; Signed-off-by: -
David S. Miller authored
Jie Wang says: ==================== net: hns3: refactor rss/tqp stats functions Currently, hns3 PF and VF module have two sets of rss and tqp stats APIs to provide get and set functions. Most of these APIs are the same. There is no need to keep these two sets of same functions for double development and bugfix work. This series refactor the rss and tqp stats APIs in hns3 PF and VF by implementing one set of common APIs for PF and VF reuse and deleting the old APIs. ==================== Signed-off-by: -
Jie Wang authored
Currently PF and VF use two sets of command code for modules to interact with firmware. These codes values are same espect the macro names. It is redundent to keep two sets of command code for same functions between PF and VF. So this patch firstly creates a unified command code for PF and VF module. We keep the macro name same with the PF command code name to avoid too many meaningless modifications. Secondly the new common command codes are used to replace the old ones in VF and deletes the old ones. Signed-off-by:
Jie Wang <wangjie125@huawei.com> Signed-off-by:
-
Jie Wang authored
This patch firstly uses new tqp struct(hclge_comm_tqp) and removes the old VF tqp struct(hclgevf_tqp). All the tqp stats members used in VF module are modified according to the new hclge_comm_tqp. Secondly VF tqp stats APIs are refactored to use new common tqp stats APIs. The old tqp stats APIs in VF are deleted. Signed-off-by:
-
Jie Wang authored
This patch firstly uses new tqp struct(hclge_comm_tqp) and deletes the old PF tqp struct(hclge_tqp). All the tqp stats members used in PF module are modified according to the new hclge_comm_tqp. Secondly PF tqp stats APIs are refactored to use new common tqp stats APIs. The old tqp stats APIs in PF are deleted. Signed-off-by:
-
Jie Wang authored
This patch creates new set of common tqp stats structures and APIs for PF and VF tqp stats module. Subfunctions such as get tqp stats, update tqp stats and reset tqp stats are inclued in this patch. These new common tqp stats APIs will be used to replace the old PF and VF tqp stats APIs in next patches. Signed-off-by:
-
Jie Wang authored
This patch uses common rss init APIs to replace the old APIs in VF rss module and removes the old VF rss init APIs. Several related Subfunctions and macros are also modified in this patch. Signed-off-by:
-
Jie Wang authored
This patch uses common rss init APIs to replace the old APIs in PF rss module and deletes the old PF rss init APIs. Some related subfunctions and macros are also modified in this patch. Signed-off-by:
-
Jie Wang authored
This patch creates new set of common rss init APIs for PF and VF rss module. Subfunctions called by rss init process are also created include rss tuple configuration and rss indirect table configuration. These new common rss init APIs will be used to replace the old PF and VF rss init APIs in next patches. Signed-off-by:
-
Jie Wang authored
This patch uses new common rss set APIs to replace the old APIs in VF rss module and removes those old rss set APIs. The related macros in VF are also modified. Signed-off-by:
-
Jie Wang authored
This patch uses new common rss set APIs to replace the old APIs in PF rss module and deletes the old rss set APIs. The related macros are also modified. Signed-off-by:
-
Jie Wang authored
Currently, hns3 PF and VF rss module have two sets of rss set APIs to configure rss. There is no need to keep two sets of these same APIs. So this patch creates new set of common rss set APIs for PF and VF reuse. These new APIs will be used to unify old APIs in next patches. Signed-off-by:
-
Jie Wang authored
This patch firstly uses new rss parameter struct(hclge_comm_rss_cfg) as child member of hclgevf_dev and deletes the original child rss parameter member(hclgevf_rss_cfg). All the rss parameter members used in VF rss module is modified according to the new hclge_comm_rss_cfg. Secondly VF rss get APIs are refactored to use new common rss get APIs. The old rss get APIs in VF are deleted. Signed-off-by:
-
Jie Wang authored
This patch firstly uses new rss parameter struct(hclge_comm_rss_cfg) as child member of hclge_dev and deletes the original child rss parameter members in vport. All the vport child rss parameter members used in PF rss module is modified according to the new hclge_comm_rss_cfg. Secondly PF rss get APIs are refactored to use new common rss get APIs. The old rss get APIs in PF are deleted. Signed-off-by:
-
Jie Wang authored
The PF and VF rss get APIs are almost the same espect the suffixes of API names. These same impementions bring double development and bugfix work. So this patch creates new common rss get APIs for PF and VF rss module. Subfunctions called by rss query process are also created(e.g. rss tuple conversion APIs). These new common rss get APIs will be used to replace PF and VF old rss APIs in next patches. Signed-off-by:
-
Jie Wang authored
Currently, there are two different sets of special command codes in PF and VF cmdq modules, this is because VF driver only uses small part of all the command codes. In other words, these not used command codes in VF are also sepcial command codes theoretically. So this patch unifes the special command codes and deletes the bool param is_pf of hclge_comm_send. All the related functions are refactored according to the new hclge_comm_send function prototype. Signed-off-by:
-
Jie Wang authored
Currently PF stores its rss parameters in vport structure. VF stores rss configurations in hclgevf_rss_cfg structure. Actually hns3 rss parameters are same beween PF and VF. The two set of rss parameters are redundent and may add extra bugfix work. So this patch creates new common rss parameter struct(hclge_comm_rss_cfg) to unify PF and VF rss configurations. These new structures will be used to unify rss configurations in PF and VF rss APIs in next patches. Signed-off-by:
-
David S. Miller authored
Horatiu Vultur says: ==================== net: lan966x: Extend switchdev with mdb support This patch series extends lan966x with mdb support by implementing the switchdev callbacks: SWITCHDEV_OBJ_ID_PORT_MDB and SWITCHDEV_OBJ_ID_HOST_MDB. It adds support for both ipv4/ipv6 entries and l2 entries. v2->v3: - rename PGID_FIRST and PGID_LAST to PGID_GP_START and PGID_GP_END - don't forget and relearn an entry for the CPU if there are more references to the cpu. v1->v2: - rename lan966x_mac_learn_impl to __lan966x_mac_learn - rename lan966x_mac_cpu_copy to lan966x_mac_ip_learn - fix grammar and typos in comments and commit messages - add reference counter for entries that copy frames to CPU ==================== Reviewed-by:
-
Horatiu Vultur authored
Extend lan966x driver with mdb support by implementing the switchdev calls: SWITCHDEV_OBJ_ID_PORT_MDB and SWITCHDEV_OBJ_ID_HOST_MDB. It is allowed to add both ipv4/ipv6 entries and l2 entries. To add ipv4/ipv6 entries is not required to use the PGID table while for l2 entries it is required. The PGID table is much smaller than MAC table so only fewer l2 entries can be added. Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by:
-
Horatiu Vultur authored
The first entries in the PGID table are used by the front ports while the last entries are used for different purposes like flooding mask, copy to CPU, etc. So add these macros to define which entries can be used for general purpose. Signed-off-by:
-
Horatiu Vultur authored
Extend mac functionality with the function lan966x_mac_ip_learn. This function adds an entry in the MAC table for IP multicast addresses. These entries can copy a frame to the CPU but also can forward on the front ports. This functionality is needed for mdb support. In case the CPU and some of the front ports subscribe to an IP multicast address. Signed-off-by:
-
