- 26 May, 2015 6 commits
-
-
Tomas Henzl authored
commit 3b747298 upstream. Sometimes when the card is restarted it may cause - "irq 16: nobody cared (try booting with the "irqpoll" option)" that is likely caused so, that the card, after the hard reset finishes, pulls on the irq. Disabling the ints before or after the hpsa_kdump_hard_reset_controller fixes it. At this point we can't know in which state the card is, so using SA5_INTR_OFF + SA5_REPLY_INTR_MASK_OFFSET defines directly, instead of the function the drivers provides, seems to be apropriate. Reviewed-by: Scott Teel <scott.teel@pmcs.com> Signed-off-by: Don Brace <don.brace@pmcs.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Tomas Henzl authored
commit 859c75ab upstream. Add a call to pci_set_master(...) missing in the previous patch "hpsa: refine the pci enable/disable handling". Found thanks to Rob Elliot. Signed-off-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Robert Elliott <elliott@hp.com> Tested-by: Robert Elliott <elliott@hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Tomas Henzl authored
commit 132aa220 upstream. When a second(kdump) kernel starts and the hard reset method is used the driver calls pci_disable_device without previously enabling it, so the kernel shows a warning - [ 16.876248] WARNING: at drivers/pci/pci.c:1431 pci_disable_device+0x84/0x90() [ 16.882686] Device hpsa disabling already-disabled device ... This patch fixes it, in addition to this I tried to balance also some other pairs of enable/disable device in the driver. Unfortunately I wasn't able to verify the functionality for the case of a sw reset, because of a lack of proper hw. Signed-off-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Konrad Rzeszutek Wilk authored
commit a6dfa128 upstream. A huge amount of NIC drivers use the DMA API, however if compiled under 32-bit an very important part of the DMA API can be ommitted leading to the drivers not working at all (especially if used with 'swiotlb=force iommu=soft'). As Prashant Sreedharan explains it: "the driver [tg3] uses DEFINE_DMA_UNMAP_ADDR(), dma_unmap_addr_set() to keep a copy of the dma "mapping" and dma_unmap_addr() to get the "mapping" value. On most of the platforms this is a no-op, but ... with "iommu=soft and swiotlb=force" this house keeping is required, ... otherwise we pass 0 while calling pci_unmap_/pci_dma_sync_ instead of the DMA address." As such enable this even when using 32-bit kernels. Reported-by: Ian Jackson <Ian.Jackson@eu.citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Prashant Sreedharan <prashant@broadcom.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Chan <mchan@broadcom.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: boris.ostrovsky@oracle.com Cc: cascardo@linux.vnet.ibm.com Cc: david.vrabel@citrix.com Cc: sanjeevb@broadcom.com Cc: siva.kallam@broadcom.com Cc: vyasevich@gmail.com Cc: xen-devel@lists.xensource.com Link: http://lkml.kernel.org/r/20150417190448.GA9462@l.oracle.comSigned-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Martin K. Petersen authored
commit 9a9324d3 upstream. The queued TRIM problems appear to be generic to Samsung's firmware and not tied to a particular model. A recent update to the 840 EVO firmware introduced the same issue as we saw on 850 Pro. Blacklist queued TRIM on all 800-series drives while we work this issue with Samsung. Reported-by: Günter Waller <g.wal@web.de> Reported-by: Sven Köhler <sven.koehler@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Martin K. Petersen authored
commit ff7f53fb upstream. Micron has released an updated firmware (MU02) for M510/M550/MX100 drives to fix the issues with queued TRIM. Queued TRIM remains broken on M500 but is working fine on later drives such as M600 and MX200. Tweak our blacklist to reflect the above. Link: https://bugzilla.kernel.org/show_bug.cgi?id=71371Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
- 21 May, 2015 1 commit
-
-
Martin Kaiser authored
drivers/gpio/gpiolib-of.c: In function 'of_gpiochip_find_and_xlate': drivers/gpio/gpiolib-of.c:52:21: warning: assignment makes integer from pointer without a cast [enabled by default] gg_data->out_gpio = ERR_PTR(ret); ^ This was introduced in 72464765, a backport of upstream commit 7b8792bb. The upstream kernel changed the type of out_gpio from int to struct gpio_desc * as part of a larger refactoring that wasn't backported Signed-off-by: Martin Kaiser <martin@kaiser.cx> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
- 20 May, 2015 14 commits
-
-
Ian Wilson authored
[ upstream commit 78146572 ] nfnl_cthelper_parse_tuple() is called from nfnl_cthelper_new(), nfnl_cthelper_get() and nfnl_cthelper_del(). In each case they pass a pointer to an nf_conntrack_tuple data structure local variable: struct nf_conntrack_tuple tuple; ... ret = nfnl_cthelper_parse_tuple(&tuple, tb[NFCTH_TUPLE]); The problem is that this local variable is not initialized, and nfnl_cthelper_parse_tuple() only initializes two fields: src.l3num and dst.protonum. This leaves all other fields with undefined values based on whatever is on the stack: tuple->src.l3num = ntohs(nla_get_be16(tb[NFCTH_TUPLE_L3PROTONUM])); tuple->dst.protonum = nla_get_u8(tb[NFCTH_TUPLE_L4PROTONUM]); The symptom observed was that when the rpc and tns helpers were added then traffic to port 1536 was being sent to user-space. Signed-off-by: Ian Wilson <iwilson@brocade.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Jiri Slaby authored
-
Lv Zheng authored
commit 1d0a0b2f upstream. ACPICA commit b60612373a4ef63b64a57c124576d7ddb6d8efb6 For physical addresses, since the address may exceed 32-bit address range after calculation, we should use 0x%8.8X%8.8X instead of ACPI_PRINTF_UINT and ACPI_FORMAT_UINT64() instead of ACPI_FORMAT_NATIVE_UINT()/ACPI_FORMAT_TO_UINT(). This patch also removes above replaced macros as there are no users. This is a preparation to switch acpi_physical_address to 64-bit on 32-bit kernel builds. Link: https://github.com/acpica/acpica/commit/b6061237Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Dirk Behme <dirk.behme@gmail.com> Signed-off-by: George G. Davis <george_davis@mentor.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Lv Zheng authored
commit cc2080b0 upstream. ACPICA commit 7f06739db43a85083a70371c14141008f20b2198 For physical addresses, since the address may exceed 32-bit address range after calculation, we should use %8.8X%8.8X (see ACPI_FORMAT_UINT64()) to convert the %p formats. This is a preparation to switch acpi_physical_address to 64-bit on 32-bit kernel builds. Link: https://github.com/acpica/acpica/commit/7f06739dSigned-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Dirk Behme <dirk.behme@gmail.com> [gdavis: Apply changes to drivers/acpi/acpica/{tbutils,tbxfload}.c] Signed-off-by: George G. Davis <george_davis@mentor.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Lv Zheng authored
commit 6d3fd3cc upstream. ACPICA commit 154f6d074dd38d6ebc0467ad454454e6c5c9ecdf There are code pieces converting pointers using "(acpi_physical_address) x" or "ACPI_CAST_PTR (t, x)" formats, this patch cleans up them. Known issues: 1. Cleanup of "(ACPI_PHYSICAL_ADDRRESS) x" for a table field For the conversions around the table fields, it is better to fix it with alignment also fixed. So this patch doesn't modify such code. There should be no functional problem by leaving them unchanged. Link: https://github.com/acpica/acpica/commit/154f6d07Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Dirk Behme <dirk.behme@gmail.com> Signed-off-by: George G. Davis <george_davis@mentor.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Lv Zheng authored
commit f254e3c5 upstream. ACPICA commit 7d9fd64397d7c38899d3dc497525f6e6b044e0e3 OSPMs like Linux expect an acpi_physical_address returning value from acpi_find_root_pointer(). This triggers warnings if sizeof (acpi_size) doesn't equal to sizeof (acpi_physical_address): drivers/acpi/osl.c:275:3: warning: passing argument 1 of 'acpi_find_root_pointer' from incompatible pointer type [enabled by default] In file included from include/acpi/acpi.h:64:0, from include/linux/acpi.h:36, from drivers/acpi/osl.c:41: include/acpi/acpixf.h:433:1: note: expected 'acpi_size *' but argument is of type 'acpi_physical_address *' This patch corrects acpi_find_root_pointer(). Link: https://github.com/acpica/acpica/commit/7d9fd643Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Dirk Behme <dirk.behme@gmail.com> Signed-off-by: George G. Davis <george_davis@mentor.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Alexey Khoroshilov authored
commit bc26d4d0 upstream. A deadlock can be initiated by userspace via ioctl(SNDCTL_SEQ_OUTOFBAND) on /dev/sequencer with TMR_ECHO midi event. In this case the control flow is: sound_ioctl() -> case SND_DEV_SEQ: case SND_DEV_SEQ2: sequencer_ioctl() -> case SNDCTL_SEQ_OUTOFBAND: spin_lock_irqsave(&lock,flags); play_event(); -> case EV_TIMING: seq_timing_event() -> case TMR_ECHO: seq_copy_to_input() -> spin_lock_irqsave(&lock,flags); It seems that spin_lock_irqsave() around play_event() is not necessary, because the only other call location in seq_startplay() makes the call without acquiring spinlock. So, the patch just removes spinlocks around play_event(). By the way, it removes unreachable code in seq_timing_event(), since (seq_mode == SEQ_2) case is handled in the beginning. Compile tested only. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: Takashi Iwai <tiwai@suse.de> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Takeshi Kihara authored
commit bad4371d upstream. f9fd54f2 ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout") changed the timeout value from 1000 jiffies to 1s. In the case where HZ is 1000 the values are the same. However, for smaller HZ values the timeout is now smaller, 1s instead of 10s in the case of HZ=100. Since the timeout occurs in spite of a normal data transfer a timeout of 10s seems more appropriate. This restores the previous timeout in the case where HZ=100 and results in an increase over the previous timeout for larger values of HZ. Fixes: f9fd54f2 ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout") Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com> [horms: rewrote changelog to refer to HZ] Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Grygorii Strashko authored
commit 184af16b upstream. The PM_RESTORE_PREPARE is not handled now in mmc_pm_notify(), as result mmc_rescan() could be scheduled and executed at late hibernation restore stages when MMC device is suspended already - which, in turn, will lead to system crash on TI dra7-evm board: WARNING: CPU: 0 PID: 3188 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x258/0x374() 44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in User mode during Functional access Hence, add missed PM_RESTORE_PREPARE PM event in mmc_pm_notify(). Fixes: 4c2ef25f (mmc: fix all hangs related to mmc/sd card...) Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Chuanxiao Dong authored
commit 4e93b9a6 upstream. During kernel boot, it will try to read some logical sectors of each block device node for the possible partition table. But since RPMB partition is special and can not be accessed by normal eMMC read / write CMDs, it will cause below error messages during kernel boot: ... mmc0: Got data interrupt 0x00000002 even though no data operation was in progress. mmcblk0rpmb: error -110 transferring data, sector 0, nr 32, cmd response 0x900, card status 0xb00 mmcblk0rpmb: retrying using single block read mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900 mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900 mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900 mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900 mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900 mmcblk0rpmb: timed out sending r/w cmd command, card status 0x400900 end_request: I/O error, dev mmcblk0rpmb, sector 0 Buffer I/O error on device mmcblk0rpmb, logical block 0 end_request: I/O error, dev mmcblk0rpmb, sector 8 Buffer I/O error on device mmcblk0rpmb, logical block 1 end_request: I/O error, dev mmcblk0rpmb, sector 16 Buffer I/O error on device mmcblk0rpmb, logical block 2 end_request: I/O error, dev mmcblk0rpmb, sector 24 Buffer I/O error on device mmcblk0rpmb, logical block 3 ... This patch will discard the access request in eMMC queue if it is RPMB partition access request. By this way, it avoids trigger above error messages. Fixes: 090d25fe ("mmc: core: Expose access to RPMB partition") Signed-off-by: Yunpeng Gao <yunpeng.gao@intel.com> Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com> Tested-by: Michael Shigorin <mike@altlinux.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Doug Anderson authored
commit c5272a28 upstream. Way back, when the world was a simpler place and there was no war, no evil, and no kernel bugs, there was just a single pinctrl lock. That was how the world was when (57291ce2 pinctrl: core device tree mapping table parsing support) was written. In that case, there were instances where the pinctrl mutex was already held when pinctrl_register_map() was called, hence a "locked" parameter was passed to the function to indicate that the mutex was already locked (so we shouldn't lock it again). A few years ago in (42fed7ba pinctrl: move subsystem mutex to pinctrl_dev struct), we switched to a separate pinctrl_maps_mutex. ...but (oops) we forgot to re-think about the whole "locked" parameter for pinctrl_register_map(). Basically the "locked" parameter appears to still refer to whether the bigger pinctrl_dev mutex is locked, but we're using it to skip locks of our (now separate) pinctrl_maps_mutex. That's kind of a bad thing(TM). Probably nobody noticed because most of the calls to pinctrl_register_map happen at boot time and we've got synchronous device probing. ...and even cases where we're asynchronous don't end up actually hitting the race too often. ...but after banging my head against the wall for a bug that reproduced 1 out of 1000 reboots and lots of looking through kgdb, I finally noticed this. Anyway, we can now safely remove the "locked" parameter and go back to a war-free, evil-free, and kernel-bug-free world. Fixes: 42fed7ba ("pinctrl: move subsystem mutex to pinctrl_dev struct") Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Christian König authored
commit d52cdfa4 upstream. MPEG 2/4 are only supported since UVD3. Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Christian König authored
commit a1b403da upstream. Invalid messages can crash the hw otherwise. Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Christian König authored
commit 013ead48 upstream. Hardware doesn't seem to work correctly, just block userspace in this case. v2: add missing defines Bugs: https://bugs.freedesktop.org/show_bug.cgi?id=85320Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
- 16 May, 2015 19 commits
-
-
Lukas Wunner authored
commit 3916e3fd upstream. Single channel LVDS maxes out at 112 MHz. The 15" pre-retina models shipped with 1440x900 (106 MHz) by default or 1680x1050 (119 MHz) as a BTO option, both versions used dual channel LVDS even though the smaller one would have fit into a single channel. Notes: Bug report showing that the MacBookPro8,2 with 1440x900 uses dual channel LVDS (this lead to it being hardcoded in intel_lvds.c by Daniel Vetter with commit 618563e3): https://bugzilla.kernel.org/show_bug.cgi?id=42842 If i915.lvds_channel_mode=2 is missing even though the machine needs it, every other vertical line is white and consequently, only the left half of the screen is visible (verified by myself on a MacBookPro9,1). Forum posting concerning a MacBookPro6,2 with 1440x900, author is using i915.lvds_channel_mode=2 on the kernel command line, proving that the machine uses dual channels: https://bbs.archlinux.org/viewtopic.php?id=185770 Chi Mei N154C6-L04 with 1440x900 is a replacement panel for all MacBook Pro "A1286" models, and that model number encompasses the MacBookPro6,2 / 8,2 / 9,1. Page 17 of the panel's datasheet shows it's driven with dual channel LVDS: http://www.ebay.com/itm/-/400690878560 http://www.everymac.com/ultimate-mac-lookup/?search_keywords=A1286 http://www.taopanel.com/chimei/datasheet/N154C6-L04.pdf Those three 15" models, MacBookPro6,2 / 8,2 / 9,1, are the only ones with i915 graphics and dual channel LVDS, so that list should be complete. And the 8,2 is already in intel_lvds.c. Possible motivation to use dual channel LVDS even on the 1440x900 models: Reduce the number of different parts, i.e. use identical logic boards and display cabling on both versions and the only differing component is the panel. Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Jani Nikula <jani.nikula@intel.com> [Jani: included notes in the commit message for posterity] Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Ulf Hansson authored
commit 11133db7 upstream. Fixes: c94a4ab7 ("ARM: ux500: Disable the MMCI gpio-regulator by default") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Ulf Hansson authored
commit f9a8c391 upstream. Fixes: c94a4ab7 ("ARM: ux500: Disable the MMCI gpio-regulator by default") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Ulf Hansson authored
commit 53d26698 upstream. The GPIO regulator for the SD-card isn't a ux500 SOC configuration, but instead it's specific to the board. Move the definition of it, into the board DTSs. Fixes: c94a4ab7 ("ARM: ux500: Disable the MMCI gpio-regulator by default") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Gregory CLEMENT authored
commit 750e30d4 upstream. There is no crystal connected to the internal RTC on the Open Block AX3. So let's disable it in order to prevent the kernel probing the driver uselessly. Eventually this patches removes the following warning message from the boot log: "rtc-mv d0010300.rtc: internal RTC not ticking" Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Fabio Estevam authored
commit cfe8c597 upstream. On imx23-olinuxino the LED turns on when level logic high is aplied to GPIO2_1. Fix the gpios property accordingly. Fixes: b34aa185 ("ARM: dts: imx23-olinuxino: Remove unneeded "default-on"") Reported-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Stefan Wahren authored
commit 0fdebe1a upstream. The dr_mode of usb0 on imx233-olinuxino is left to default "otg". Since the green LED (GPIO2_1) on imx233-olinuxino is connected to the same pin as USB_OTG_ID it's possible to disable USB host by LED toggling: echo 0 > /sys/class/leds/green/brightness [ 1068.890000] ci_hdrc ci_hdrc.0: remove, state 1 [ 1068.890000] usb usb1: USB disconnect, device number 1 [ 1068.920000] usb 1-1: USB disconnect, device number 2 [ 1068.920000] usb 1-1.1: USB disconnect, device number 3 [ 1069.070000] usb 1-1.2: USB disconnect, device number 4 [ 1069.450000] ci_hdrc ci_hdrc.0: USB bus 1 deregistered [ 1074.460000] ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11 This patch fixes the issue by setting dr_mode to "host" in the dts file. Reported-by: Harald Geyer <harald@ccbib.org> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Marek Vasut <marex@denx.de> Acked-by: Peter Chen <peter.chen@freescale.com> Fixes: b4931294 ("ARM: dts: imx23-olinuxino: Add USB host support") Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Marek Vasut authored
commit 4ada77e3 upstream. Fix a typo in the TX DMA interrupt name for AUART4. This patch makes AUART4 operational again. Signed-off-by: Marek Vasut <marex@denx.de> Fixes: f30fb03d ("ARM: dts: add generic DMA device tree binding for mxs-dma") Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Markus Pargmann authored
commit f90d3f0d upstream. The property '#pwm-cells' is currently missing. It is not possible to use pwm4 without this property. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Fixes: 5658a68f ("ARM i.MX25: Add devicetree") Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Boris Ostrovsky authored
commit b9d934f2 upstream. After a resume the hypervisor/tools may change console event channel number. We should re-query it. Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Naoya Horiguchi authored
commit 602498f9 upstream. If multiple soft offline events hit one free page/hugepage concurrently, soft_offline_page() can handle the free page/hugepage multiple times, which makes num_poisoned_pages counter increased more than once. This patch fixes this wrong counting by checking TestSetPageHWPoison for normal papes and by checking the return value of dequeue_hwpoisoned_huge_page() for hugepages. Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Acked-by: Dean Nelson <dnelson@redhat.com> Cc: Andi Kleen <andi@firstfloor.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Tejun Heo authored
commit 464d1387 upstream. mm/page-writeback.c has several places where 1 is added to the divisor to prevent division by zero exceptions; however, if the original divisor is equivalent to -1, adding 1 leads to division by zero. There are three places where +1 is used for this purpose - one in pos_ratio_polynom() and two in bdi_position_ratio(). The second one in bdi_position_ratio() actually triggered div-by-zero oops on a machine running a 3.10 kernel. The divisor is x_intercept - bdi_setpoint + 1 == span + 1 span is confirmed to be (u32)-1. It isn't clear how it ended up that but it could be from write bandwidth calculation underflow fixed by c72efb65 ("writeback: fix possible underflow in write bandwidth calculation"). At any rate, +1 isn't a proper protection against div-by-zero. This patch converts all +1 protections to |1. Note that bdi_update_dirty_ratelimit() was already using |1 before this patch. Signed-off-by: Tejun Heo <tj@kernel.org> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Naoya Horiguchi authored
commit 09789e5d upstream. Currently memory_failure() calls shake_page() to sweep pages out from pcplists only when the victim page is 4kB LRU page or thp head page. But we should do this for a thp tail page too. Consider that a memory error hits a thp tail page whose head page is on a pcplist when memory_failure() runs. Then, the current kernel skips shake_pages() part, so hwpoison_user_mappings() returns without calling split_huge_page() nor try_to_unmap() because PageLRU of the thp head is still cleared due to the skip of shake_page(). As a result, me_huge_page() runs for the thp, which is broken behavior. One effect is a leak of the thp. And another is to fail to isolate the memory error, so later access to the error address causes another MCE, which kills the processes which used the thp. This patch fixes this problem by calling shake_page() for thp tail case. Fixes: 385de357 ("thp: allow a hwpoisoned head page to be put back to LRU") Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Reviewed-by: Andi Kleen <ak@linux.intel.com> Acked-by: Dean Nelson <dnelson@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com> Cc: Jin Dongming <jin.dongming@np.css.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Eric W. Biederman authored
commit 7e96c1b0 upstream. This fixes a dumb bug in fs_fully_visible that allows proc or sys to be mounted if there is a bind mount of part of /proc/ or /sys/ visible. Reported-by: Eric Windisch <ewindisch@docker.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Johan Hovold authored
commit 483d8211 upstream. Unregister GPIOs requested through sysfs at chip remove to avoid leaking the associated memory and sysfs entries. The stale sysfs entries prevented the gpio numbers from being exported when the gpio range was later reused (e.g. at device reconnect). This also fixes the related module-reference leak. Note that kernfs makes sure that any on-going sysfs operations finish before the class devices are unregistered and that further accesses fail. The chip exported flag is used to prevent gpiod exports during removal. This also makes it harder to trigger, but does not fix, the related race between gpiochip_remove and export_store, which is really a race with gpiod_request that needs to be addressed separately. Also note that this would prevent the crashes (e.g. NULL-dereferences) at reconnect that affects pre-3.18 kernels, as well as use-after-free on operations on open attribute files on pre-3.14 kernels (prior to kernfs). Fixes: d8f388d8 ("gpio: sysfs interface") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Johan Hovold authored
commit 01cca93a upstream. Unregister gpiochip device (used to export information through sysfs) before removing it internally. This way removal will reverse addition. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Jason Gunthorpe authored
commit 28521440 upstream. When accepting a new IPv4 connect to an IPv6 socket, the CMA tries to canonize the address family to IPv4, but does not properly process the listening sockaddr to get the listening port, and does not properly set the address family of the canonized sockaddr. Fixes: e51060f0 ("IB: IP address based RDMA connection manager") Reported-By: Yotam Kenneth <yotamke@mellanox.com> Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Tested-by: Haggai Eran <haggaie@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Ryusuke Konishi authored
commit d8fd150f upstream. The range check for b-tree level parameter in nilfs_btree_root_broken() is wrong; it accepts the case of "level == NILFS_BTREE_LEVEL_MAX" even though the level is limited to values in the range of 0 to (NILFS_BTREE_LEVEL_MAX - 1). Since the level parameter is read from storage device and used to index nilfs_btree_path array whose element count is NILFS_BTREE_LEVEL_MAX, it can cause memory overrun during btree operations if the boundary value is set to the level parameter on device. This fixes the broken sanity check and adds a comment to clarify that the upper bound NILFS_BTREE_LEVEL_MAX is exclusive. Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-
Junxiao Bi authored
commit b1432a2a upstream. There is a race window in dlm_get_lock_resource(), which may return a lock resource which has been purged. This will cause the process to hang forever in dlmlock() as the ast msg can't be handled due to its lock resource not existing. dlm_get_lock_resource { ... spin_lock(&dlm->spinlock); tmpres = __dlm_lookup_lockres_full(dlm, lockid, namelen, hash); if (tmpres) { spin_unlock(&dlm->spinlock); >>>>>>>> race window, dlm_run_purge_list() may run and purge the lock resource spin_lock(&tmpres->spinlock); ... spin_unlock(&tmpres->spinlock); } } Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <joseph.qi@huawei.com> Cc: Mark Fasheh <mfasheh@suse.com> Cc: Joel Becker <jlbec@evilplan.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
-