- 07 Feb, 2018 5 commits
-
-
Yu Wang authored
If device gone during chip reset, ar->normal_mode_fw.board is not initialized, but ath10k_debug_print_hwfw_info() will try to access its member, which will cause 'kernel NULL pointer' issue. This was found using a faulty device (pci link went down sometimes) in a random insmod/rmmod/other-op test. To fix it, check ar->normal_mode_fw.board before accessing the member. pci 0000:02:00.0: BAR 0: assigned [mem 0xf7400000-0xf75fffff 64bit] ath10k_pci 0000:02:00.0: enabling device (0000 -> 0002) ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 ath10k_pci 0000:02:00.0: failed to read device register, device is gone ath10k_pci 0000:02:00.0: failed to wait for target init: -5 ath10k_pci 0000:02:00.0: failed to warm reset: -5 ath10k_pci 0000:02:00.0: firmware crashed during chip reset ath10k_pci 0000:02:00.0: firmware crashed! (uuid 5d018951-b8e1-404a-8fde-923078b4423a) ath10k_pci 0000:02:00.0: (null) target 0x00000000 chip_id 0x00340aff sub 0000:0000 ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1 ath10k_pci 0000:02:00.0: firmware ver api 0 features crc32 00000000 ... BUG: unable to handle kernel NULL pointer dereference at 00000004 ... Call Trace: [<fb4e7882>] ath10k_print_driver_info+0x12/0x20 [ath10k_core] [<fb62b7dd>] ath10k_pci_fw_crashed_dump+0x6d/0x4d0 [ath10k_pci] [<fb629f07>] ? ath10k_pci_sleep.part.19+0x57/0xc0 [ath10k_pci] [<fb62c8ee>] ath10k_pci_hif_power_up+0x14e/0x1b0 [ath10k_pci] [<c10477fb>] ? do_page_fault+0xb/0x10 [<fb4eb934>] ath10k_core_register_work+0x24/0x840 [ath10k_core] [<c18a00d8>] ? netlbl_unlhsh_remove+0x178/0x410 [<c10477f0>] ? __do_page_fault+0x480/0x480 [<c1068e44>] process_one_work+0x114/0x3e0 [<c1069d07>] worker_thread+0x37/0x4a0 [<c106e294>] kthread+0xa4/0xc0 [<c1069cd0>] ? create_worker+0x180/0x180 [<c106e1f0>] ? kthread_park+0x50/0x50 [<c18ab4f7>] ret_from_fork+0x1b/0x28 Code: 78 80 b8 50 09 00 00 00 75 5d 8d 75 94 c7 44 24 08 aa d7 52 fb c7 44 24 04 64 00 00 00 89 34 24 e8 82 52 e2 c5 8b 83 dc 08 00 00 <8b> 50 04 8b 08 31 c0 e8 20 57 e3 c5 89 44 24 10 8b 83 58 09 00 EIP: [<fb4e7754>]- ath10k_debug_print_board_info+0x34/0xb0 [ath10k_core] SS:ESP 0068:f4921d90 CR2: 0000000000000004 Signed-off-by:
Yu Wang <yyuwang@codeaurora.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Wojciech Dubowik authored
Commit 8da58553 ("ath9k: Use calibrated noise floor value when available") introduced regression in ath9k_hw_getchan_noise where per chain nominal noise floor has been taken instead default for channel. Revert to original default channel noise floor. Fixes: 8da58553 ("ath9k: Use calibrated noise floor value when available") Reported-by:
Sebastian Gottschall <s.gottschall@dd-wrt.com> Signed-off-by:
Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by:
-
Tobias Schramm authored
Some modern Ubiquiti devices contain a rebranded QCA988X rev2 with a custom Ubiquiti vendor and device id. This patch adds support for those devices, treating them as a QCA988X v2. Signed-off-by:
Tobias Schramm <tobleminer@gmail.com> [kvalo@codeaurora.org: rebase, add missing fields in hw_params, fix a long line in pci.c:61] Signed-off-by:
-
Tobias Schramm authored
Acked-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Yu Wang authored
The length of DRAM dump for QCA6174 hw3.0/hw3.2 and QCA9377 hw1.1 are less than the actual value, some coredump contents are missed. To fix it, change the length from 0x90000 to 0xa8000. Fixes: 703f261d ("ath10k: add memory dump support for QCA6174/QCA9377") Signed-off-by:
-
- 01 Feb, 2018 5 commits
-
-
Felix Fietkau authored
Avoids data connection stalls when the client toggles powersave mode Fixes: aee5b8cf ("mt76: implement A-MPDU rx reordering in the driver code") Signed-off-by:
Felix Fietkau <nbd@nbd.name> Signed-off-by:
-
Felix Fietkau authored
Fixes: aee5b8cf ("mt76: implement A-MPDU rx reordering in the driver code") Signed-off-by:
-
Felix Fietkau authored
Avoids timeouts on reordered A-MPDU rx frames Fixes: aee5b8cf ("mt76: implement A-MPDU rx reordering in the driver code") Signed-off-by:
-
Felix Fietkau authored
With software A-MPDU reordering in place, frames that notify mac80211 of powersave changes are reordered as well, which can cause connection stalls. Fix this by implementing powersave state processing in the driver. Fixes: aee5b8cf ("mt76: implement A-MPDU rx reordering in the driver code") Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers.gitKalle Valo authored
The last pull request didn't make it to v4.15 (I was too late) so pull it to wireless-drivers-next.git instead so that it can go to v4.16.
-
- 29 Jan, 2018 30 commits
-
-
Thomas Falcon authored
Wait for a response from the VNIC server before exiting after setting the MAC address. The resolves an issue with bonding a VNIC client in ALB or TLB modes. The bonding driver was changing the MAC address more rapidly than the device could respond, causing the following errors. "bond0: the hw address of slave eth2 is in use by the bond; couldn't find a slave with a free hw address to give it (this should not have happened)" If the function waits until the change is finalized, these errors are avoided. Signed-off-by:
Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Junxiao Bi authored
The following soft lockup was caught. This is a deadlock caused by recusive locking. Process kworker/u40:1:28016 was holding spin lock "mbx->queue_lock" in qlcnic_83xx_mailbox_worker(), while a softirq came in and ask the same spin lock in qlcnic_83xx_enqueue_mbx_cmd(). This lock should be hold by disable bh.. [161846.962125] NMI watchdog: BUG: soft lockup - CPU#1 stuck for 22s! [kworker/u40:1:28016] [161846.962367] Modules linked in: tun ocfs2 xen_netback xen_blkback xen_gntalloc xen_gntdev xen_evtchn xenfs xen_privcmd autofs4 ocfs2_dlmfs ocfs2_stack_o2cb ocfs2_dlm ocfs2_nodemanager ocfs2_stackglue configfs bnx2fc fcoe libfcoe libfc sunrpc 8021q mrp garp bridge stp llc bonding dm_round_robin dm_multipath iTCO_wdt iTCO_vendor_support pcspkr sb_edac edac_core i2c_i801 shpchp lpc_ich mfd_core ioatdma ipmi_devintf ipmi_si ipmi_msghandler sg ext4 jbd2 mbcache2 sr_mod cdrom sd_mod igb i2c_algo_bit i2c_core ahci libahci megaraid_sas ixgbe dca ptp pps_core vxlan udp_tunnel ip6_udp_tunnel qla2xxx scsi_transport_fc qlcnic crc32c_intel be2iscsi bnx2i cnic uio cxgb4i cxgb4 cxgb3i libcxgbi ipv6 cxgb3 mdio libiscsi_tcp qla4xxx iscsi_boot_sysfs libiscsi scsi_transport_iscsi dm_mirror dm_region_hash dm_log dm_mod [161846.962454] [161846.962460] CPU: 1 PID: 28016 Comm: kworker/u40:1 Not tainted 4.1.12-94.5.9.el6uek.x86_64 #2 [161846.962463] Hardware name: Oracle Corporation SUN SERVER X4-2L /ASSY,MB,X4-2L , BIOS 26050100 09/19/2017 [161846.962489] Workqueue: qlcnic_mailbox qlcnic_83xx_mailbox_worker [qlcnic] [161846.962493] task: ffff8801f2e34600 ti: ffff88004ca5c000 task.ti: ffff88004ca5c000 [161846.962496] RIP: e030:[<ffffffff810013aa>] [<ffffffff810013aa>] xen_hypercall_sched_op+0xa/0x20 [161846.962506] RSP: e02b:ffff880202e43388 EFLAGS: 00000206 [161846.962509] RAX: 0000000000000000 RBX: ffff8801f6996b70 RCX: ffffffff810013aa [161846.962511] RDX: ffff880202e433cc RSI: ffff880202e433b0 RDI: 0000000000000003 [161846.962513] RBP: ffff880202e433d0 R08: 0000000000000000 R09: ffff8801fe893200 [161846.962516] R10: ffff8801fe400538 R11: 0000000000000206 R12: ffff880202e4b000 [161846.962518] R13: 0000000000000050 R14: 0000000000000001 R15: 000000000000020d [161846.962528] FS: 0000000000000000(0000) GS:ffff880202e40000(0000) knlGS:ffff880202e40000 [161846.962531] CS: e033 DS: 0000 ES: 0000 CR0: 0000000080050033 [161846.962533] CR2: 0000000002612640 CR3: 00000001bb796000 CR4: 0000000000042660 [161846.962536] Stack: [161846.962538] ffff880202e43608 0000000000000000 ffffffff813f0442 ffff880202e433b0 [161846.962543] 0000000000000000 ffff880202e433cc ffffffff00000001 0000000000000000 [161846.962547] 00000009813f03d6 ffff880202e433e0 ffffffff813f0460 ffff880202e43440 [161846.962552] Call Trace: [161846.962555] <IRQ> [161846.962565] [<ffffffff813f0442>] ? xen_poll_irq_timeout+0x42/0x50 [161846.962570] [<ffffffff813f0460>] xen_poll_irq+0x10/0x20 [161846.962578] [<ffffffff81014222>] xen_lock_spinning+0xe2/0x110 [161846.962583] [<ffffffff81013f01>] __raw_callee_save_xen_lock_spinning+0x11/0x20 [161846.962592] [<ffffffff816e5c57>] ? _raw_spin_lock+0x57/0x80 [161846.962609] [<ffffffffa028acfc>] qlcnic_83xx_enqueue_mbx_cmd+0x7c/0xe0 [qlcnic] [161846.962623] [<ffffffffa028e008>] qlcnic_83xx_issue_cmd+0x58/0x210 [qlcnic] [161846.962636] [<ffffffffa028caf2>] qlcnic_83xx_sre_macaddr_change+0x162/0x1d0 [qlcnic] [161846.962649] [<ffffffffa028cb8b>] qlcnic_83xx_change_l2_filter+0x2b/0x30 [qlcnic] [161846.962657] [<ffffffff8160248b>] ? __skb_flow_dissect+0x18b/0x650 [161846.962670] [<ffffffffa02856e5>] qlcnic_send_filter+0x205/0x250 [qlcnic] [161846.962682] [<ffffffffa0285c77>] qlcnic_xmit_frame+0x547/0x7b0 [qlcnic] [161846.962691] [<ffffffff8160ac22>] xmit_one+0x82/0x1a0 [161846.962696] [<ffffffff8160ad90>] dev_hard_start_xmit+0x50/0xa0 [161846.962701] [<ffffffff81630112>] sch_direct_xmit+0x112/0x220 [161846.962706] [<ffffffff8160b80f>] __dev_queue_xmit+0x1df/0x5e0 [161846.962710] [<ffffffff8160bc33>] dev_queue_xmit_sk+0x13/0x20 [161846.962721] [<ffffffffa0575bd5>] bond_dev_queue_xmit+0x35/0x80 [bonding] [161846.962729] [<ffffffffa05769fb>] __bond_start_xmit+0x1cb/0x210 [bonding] [161846.962736] [<ffffffffa0576a71>] bond_start_xmit+0x31/0x60 [bonding] [161846.962740] [<ffffffff8160ac22>] xmit_one+0x82/0x1a0 [161846.962745] [<ffffffff8160ad90>] dev_hard_start_xmit+0x50/0xa0 [161846.962749] [<ffffffff8160bb1e>] __dev_queue_xmit+0x4ee/0x5e0 [161846.962754] [<ffffffff8160bc33>] dev_queue_xmit_sk+0x13/0x20 [161846.962760] [<ffffffffa05cfa72>] vlan_dev_hard_start_xmit+0xb2/0x150 [8021q] [161846.962764] [<ffffffff8160ac22>] xmit_one+0x82/0x1a0 [161846.962769] [<ffffffff8160ad90>] dev_hard_start_xmit+0x50/0xa0 [161846.962773] [<ffffffff8160bb1e>] __dev_queue_xmit+0x4ee/0x5e0 [161846.962777] [<ffffffff8160bc33>] dev_queue_xmit_sk+0x13/0x20 [161846.962789] [<ffffffffa05adf74>] br_dev_queue_push_xmit+0x54/0xa0 [bridge] [161846.962797] [<ffffffffa05ae4ff>] br_forward_finish+0x2f/0x90 [bridge] [161846.962807] [<ffffffff810b0dad>] ? ttwu_do_wakeup+0x1d/0x100 [161846.962811] [<ffffffff815f929b>] ? __alloc_skb+0x8b/0x1f0 [161846.962818] [<ffffffffa05ae04d>] __br_forward+0x8d/0x120 [bridge] [161846.962822] [<ffffffff815f613b>] ? __kmalloc_reserve+0x3b/0xa0 [161846.962829] [<ffffffff810be55e>] ? update_rq_runnable_avg+0xee/0x230 [161846.962836] [<ffffffffa05ae176>] br_forward+0x96/0xb0 [bridge] [161846.962845] [<ffffffffa05af85e>] br_handle_frame_finish+0x1ae/0x420 [bridge] [161846.962853] [<ffffffffa05afc4f>] br_handle_frame+0x17f/0x260 [bridge] [161846.962862] [<ffffffffa05afad0>] ? br_handle_frame_finish+0x420/0x420 [bridge] [161846.962867] [<ffffffff8160d057>] __netif_receive_skb_core+0x1f7/0x870 [161846.962872] [<ffffffff8160d6f2>] __netif_receive_skb+0x22/0x70 [161846.962877] [<ffffffff8160d913>] netif_receive_skb_internal+0x23/0x90 [161846.962884] [<ffffffffa07512ea>] ? xenvif_idx_release+0xea/0x100 [xen_netback] [161846.962889] [<ffffffff816e5a10>] ? _raw_spin_unlock_irqrestore+0x20/0x50 [161846.962893] [<ffffffff8160e624>] netif_receive_skb_sk+0x24/0x90 [161846.962899] [<ffffffffa075269a>] xenvif_tx_submit+0x2ca/0x3f0 [xen_netback] [161846.962906] [<ffffffffa0753f0c>] xenvif_tx_action+0x9c/0xd0 [xen_netback] [161846.962915] [<ffffffffa07567f5>] xenvif_poll+0x35/0x70 [xen_netback] [161846.962920] [<ffffffff8160e01b>] napi_poll+0xcb/0x1e0 [161846.962925] [<ffffffff8160e1c0>] net_rx_action+0x90/0x1c0 [161846.962931] [<ffffffff8108aaba>] __do_softirq+0x10a/0x350 [161846.962938] [<ffffffff8108ae75>] irq_exit+0x125/0x130 [161846.962943] [<ffffffff813f03a9>] xen_evtchn_do_upcall+0x39/0x50 [161846.962950] [<ffffffff816e7ffe>] xen_do_hypervisor_callback+0x1e/0x40 [161846.962952] <EOI> [161846.962959] [<ffffffff816e5c4a>] ? _raw_spin_lock+0x4a/0x80 [161846.962964] [<ffffffff816e5b1e>] ? _raw_spin_lock_irqsave+0x1e/0xa0 [161846.962978] [<ffffffffa028e279>] ? qlcnic_83xx_mailbox_worker+0xb9/0x2a0 [qlcnic] [161846.962991] [<ffffffff810a14e1>] ? process_one_work+0x151/0x4b0 [161846.962995] [<ffffffff8100c3f2>] ? check_events+0x12/0x20 [161846.963001] [<ffffffff810a1960>] ? worker_thread+0x120/0x480 [161846.963005] [<ffffffff816e187b>] ? __schedule+0x30b/0x890 [161846.963010] [<ffffffff810a1840>] ? process_one_work+0x4b0/0x4b0 [161846.963015] [<ffffffff810a1840>] ? process_one_work+0x4b0/0x4b0 [161846.963021] [<ffffffff810a6b3e>] ? kthread+0xce/0xf0 [161846.963025] [<ffffffff810a6a70>] ? kthread_freezable_should_stop+0x70/0x70 [161846.963031] [<ffffffff816e6522>] ? ret_from_fork+0x42/0x70 [161846.963035] [<ffffffff810a6a70>] ? kthread_freezable_should_stop+0x70/0x70 [161846.963037] Code: cc 51 41 53 b8 1c 00 00 00 0f 05 41 5b 59 c3 cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc 51 41 53 b8 1d 00 00 00 0f 05 <41> 5b 59 c3 cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc Signed-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by:
-
Li RongQing authored
socket can be disconnected and gets transformed back to a listening socket, if sk_frag.page is not released, which will be cloned into a new socket by sk_clone_lock, but the reference count of this page is increased, lead to a use after free or double free issue Signed-off-by:
Li RongQing <lirongqing@baidu.com> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Tonghao Zhang authored
When using ioctl to get address of interface, we can't get it anymore. For example, the command is show as below. # ifconfig eth0 In the patch ("03aef17b"), the devinet_ioctl does not return a suitable value, even though we can find it in the kernel. Then fix it now. Fixes: 03aef17b ("devinet_ioctl(): take copyin/copyout to caller") Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:Tonghao Zhang <xiangxia.m.yue@gmail.com> Acked-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Eric Dumazet authored
syzbot reported a lockdep splat in gen_new_estimator() / est_fetch_counters() when attempting to lock est->stats_lock. Since est_fetch_counters() is called from BH context from timer interrupt, we need to block BH as well when calling it from process context. Most qdiscs use per cpu counters and are immune to the problem, but net/sched/act_api.c and net/netfilter/xt_RATEEST.c are using a spinlock to protect their data. They both call gen_new_estimator() while object is created and not yet alive, so this bug could not trigger a deadlock, only a lockdep splat. Fixes: 1c0d32fd ("net_sched: gen_estimator: complete rewrite of rate estimators") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Acked-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Harini Katakam authored
Handle HRESP error by doing a SW reset of RX and TX and re-initializing the descriptors, RX and TX queue pointers. Signed-off-by:
Harini Katakam <harinik@xilinx.com> Signed-off-by:
Michal Simek <michal.simek@xilinx.com> Signed-off-by:
-
Gal Pressman authored
On TTC table creation, the indirection TIRs should be used instead of the inner indirection TIRs. Fixes: 1ae1df3a ("net/mlx5e: Refactor RSS related objects and code") Signed-off-by:
Gal Pressman <galp@mellanox.com> Reviewed-by:
Shalom Lagziel <shaloml@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
-
Eric Dumazet authored
Heiner reported a lockdep splat [1] This is caused by attempting GFP_KERNEL allocation while RCU lock is held and BH blocked. We believe that addrconf_verify_rtnl() could run for a long period, so instead of using GFP_ATOMIC here as Ido suggested, we should break the critical section and restart it after the allocation. [1] [86220.125562] ============================= [86220.125586] WARNING: suspicious RCU usage [86220.125612] 4.15.0-rc7-next-20180110+ #7 Not tainted [86220.125641] ----------------------------- [86220.125666] kernel/sched/core.c:6026 Illegal context switch in RCU-bh read-side critical section! [86220.125711] other info that might help us debug this: [86220.125755] rcu_scheduler_active = 2, debug_locks = 1 [86220.125792] 4 locks held by kworker/0:2/1003: [86220.125817] #0: ((wq_completion)"%s"("ipv6_addrconf")){+.+.}, at: [<00000000da8e9b73>] process_one_work+0x1de/0x680 [86220.125895] #1: ((addr_chk_work).work){+.+.}, at: [<00000000da8e9b73>] process_one_work+0x1de/0x680 [86220.125959] #2: (rtnl_mutex){+.+.}, at: [<00000000b06d9510>] rtnl_lock+0x12/0x20 [86220.126017] #3: (rcu_read_lock_bh){....}, at: [<00000000aef52299>] addrconf_verify_rtnl+0x1e/0x510 [ipv6] [86220.126111] stack backtrace: [86220.126142] CPU: 0 PID: 1003 Comm: kworker/0:2 Not tainted 4.15.0-rc7-next-20180110+ #7 [86220.126185] Hardware name: ZOTAC ZBOX-CI321NANO/ZBOX-CI321NANO, BIOS B246P105 06/01/2015 [86220.126250] Workqueue: ipv6_addrconf addrconf_verify_work [ipv6] [86220.126288] Call Trace: [86220.126312] dump_stack+0x70/0x9e [86220.126337] lockdep_rcu_suspicious+0xce/0xf0 [86220.126365] ___might_sleep+0x1d3/0x240 [86220.126390] __might_sleep+0x45/0x80 [86220.126416] kmem_cache_alloc_trace+0x53/0x250 [86220.126458] ? ipv6_add_addr+0xfe/0x6e0 [ipv6] [86220.126498] ipv6_add_addr+0xfe/0x6e0 [ipv6] [86220.126538] ipv6_create_tempaddr+0x24d/0x430 [ipv6] [86220.126580] ? ipv6_create_tempaddr+0x24d/0x430 [ipv6] [86220.126623] addrconf_verify_rtnl+0x339/0x510 [ipv6] [86220.126664] ? addrconf_verify_rtnl+0x339/0x510 [ipv6] [86220.126708] addrconf_verify_work+0xe/0x20 [ipv6] [86220.126738] process_one_work+0x258/0x680 [86220.126765] worker_thread+0x35/0x3f0 [86220.126790] kthread+0x124/0x140 [86220.126813] ? process_one_work+0x680/0x680 [86220.126839] ? kthread_create_worker_on_cpu+0x40/0x40 [86220.126869] ? umh_complete+0x40/0x40 [86220.126893] ? call_usermodehelper_exec_async+0x12a/0x160 [86220.126926] ret_from_fork+0x4b/0x60 [86220.126999] BUG: sleeping function called from invalid context at mm/slab.h:420 [86220.127041] in_atomic(): 1, irqs_disabled(): 0, pid: 1003, name: kworker/0:2 [86220.127082] 4 locks held by kworker/0:2/1003: [86220.127107] #0: ((wq_completion)"%s"("ipv6_addrconf")){+.+.}, at: [<00000000da8e9b73>] process_one_work+0x1de/0x680 [86220.127179] #1: ((addr_chk_work).work){+.+.}, at: [<00000000da8e9b73>] process_one_work+0x1de/0x680 [86220.127242] #2: (rtnl_mutex){+.+.}, at: [<00000000b06d9510>] rtnl_lock+0x12/0x20 [86220.127300] #3: (rcu_read_lock_bh){....}, at: [<00000000aef52299>] addrconf_verify_rtnl+0x1e/0x510 [ipv6] [86220.127414] CPU: 0 PID: 1003 Comm: kworker/0:2 Not tainted 4.15.0-rc7-next-20180110+ #7 [86220.127463] Hardware name: ZOTAC ZBOX-CI321NANO/ZBOX-CI321NANO, BIOS B246P105 06/01/2015 [86220.127528] Workqueue: ipv6_addrconf addrconf_verify_work [ipv6] [86220.127568] Call Trace: [86220.127591] dump_stack+0x70/0x9e [86220.127616] ___might_sleep+0x14d/0x240 [86220.127644] __might_sleep+0x45/0x80 [86220.127672] kmem_cache_alloc_trace+0x53/0x250 [86220.127717] ? ipv6_add_addr+0xfe/0x6e0 [ipv6] [86220.127762] ipv6_add_addr+0xfe/0x6e0 [ipv6] [86220.127807] ipv6_create_tempaddr+0x24d/0x430 [ipv6] [86220.127854] ? ipv6_create_tempaddr+0x24d/0x430 [ipv6] [86220.127903] addrconf_verify_rtnl+0x339/0x510 [ipv6] [86220.127950] ? addrconf_verify_rtnl+0x339/0x510 [ipv6] [86220.127998] addrconf_verify_work+0xe/0x20 [ipv6] [86220.128032] process_one_work+0x258/0x680 [86220.128063] worker_thread+0x35/0x3f0 [86220.128091] kthread+0x124/0x140 [86220.128117] ? process_one_work+0x680/0x680 [86220.128146] ? kthread_create_worker_on_cpu+0x40/0x40 [86220.128180] ? umh_complete+0x40/0x40 [86220.128207] ? call_usermodehelper_exec_async+0x12a/0x160 [86220.128243] ret_from_fork+0x4b/0x60 Fixes: f3d9832e ("ipv6: addrconf: cleanup locking in ipv6_add_addr") Signed-off-by:Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Wei Wang authored
In current route cache aging logic, if a route has both RTF_EXPIRE and RTF_GATEWAY set, the route will only be removed if the neighbor cache has no NTF_ROUTER flag. Otherwise, even if the route has expired, it won't get deleted. Fix this logic to always check if the route has expired first and then do the gateway neighbor cache check if previous check decide to not remove the exception entry. Fixes: 1859bac0 ("ipv6: remove from fib tree aged out RTF_CACHE dst") Signed-off-by:
Wei Wang <weiwan@google.com> Signed-off-by:
Martin KaFai Lau <kafai@fb.com> Acked-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Alexander Duyck authored
When compared to ixgbe and other previous Intel drivers the i40e and i40evf drivers actually reserve 2 additional descriptors in maybe_stop_tx for cache line alignment. We need to update DESC_NEEDED to reflect this as otherwise we are more likely to return TX_BUSY which will cause issues with things like xmit_more. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Andy Gospodarek authored
Make sure to cancel any pending work that might update driver coalesce settings when taking down an interface. Fixes: 6a8788f2 ("bnxt_en: add support for software dynamic interrupt moderation") Signed-off-by:
Andy Gospodarek <gospo@broadcom.com> Cc: Michael Chan <michael.chan@broadcom.com> Acked-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
David Ahern authored
Unsolicited IPv6 neighbor advertisements should be sent after DAD completes. Update ndisc_send_unsol_na to skip tentative, non-optimistic addresses and have those sent by addrconf_dad_completed after DAD. Fixes: 4a6e3c5d ("net: ipv6: send unsolicited NA on admin up") Reported-by:
Vivek Venkatraman <vivek@cumulusnetworks.com> Signed-off-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
Andy Spencer authored
When the frame check sequence (FCS) is split across the last two frames of a fragmented packet, part of the FCS gets counted twice, once when subtracting the FCS, and again when subtracting the previously received data. For example, if 1602 bytes are received, and the first fragment contains the first 1600 bytes (including the first two bytes of the FCS), and the second fragment contains the last two bytes of the FCS: 'skb->len == 1600' from the first fragment size = lstatus & BD_LENGTH_MASK; # 1602 size -= ETH_FCS_LEN; # 1598 size -= skb->len; # -2 Since the size is unsigned, it wraps around and causes a BUG later in the packet handling, as shown below: kernel BUG at ./include/linux/skbuff.h:2068! Oops: Exception in kernel mode, sig: 5 [#1] ... NIP [c021ec60] skb_pull+0x24/0x44 LR [c01e2fbc] gfar_clean_rx_ring+0x498/0x690 Call Trace: [df7edeb0] [c01e2c1c] gfar_clean_rx_ring+0xf8/0x690 (unreliable) [df7edf20] [c01e33a8] gfar_poll_rx_sq+0x3c/0x9c [df7edf40] [c023352c] net_rx_action+0x21c/0x274 [df7edf90] [c0329000] __do_softirq+0xd8/0x240 [df7edff0] [c000c108] call_do_irq+0x24/0x3c [c0597e90] [c00041dc] do_IRQ+0x64/0xc4 [c0597eb0] [c000d920] ret_from_except+0x0/0x18 --- interrupt: 501 at arch_cpu_idle+0x24/0x5c Change the size to a signed integer and then trim off any part of the FCS that was received prior to the last fragment. Fixes: 6c389fc9 ("gianfar: fix size of scatter-gathered frames") Signed-off-by:
Andy Spencer <aspencer@spacex.com> Signed-off-by:
-
David S. Miller authored
Cong Wang says: ==================== net_sched: reflect tx_queue_len change for pfifo_fast This pathcset restores the pfifo_fast qdisc behavior of dropping packets based on latest dev->tx_queue_len. Patch 1 introduces a helper, patch 2 introduces a new Qdisc ops which is called when we modify tx_queue_len, patch 3 implements this ops for pfifo_fast. Please see each patch for details. --- v3: use skb_array_resize_multiple() v2: handle error case for ->change_tx_queue_len() ==================== Signed-off-by: -
Cong Wang authored
pfifo_fast used to drop based on qdisc_dev(qdisc)->tx_queue_len, so we have to resize skb array when we change tx_queue_len. Other qdiscs which read tx_queue_len are fine because they all save it to sch->limit or somewhere else in qdisc during init. They don't have to implement this, it is nicer if they do so that users don't have to re-configure qdisc after changing tx_queue_len. Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by:
-
Cong Wang authored
Introduce a new qdisc ops ->change_tx_queue_len() so that each qdisc could decide how to implement this if it wants. Previously we simply read dev->tx_queue_len, after pfifo_fast switches to skb array, we need this API to resize the skb array when we change dev->tx_queue_len. To avoid handling race conditions with TX BH, we need to deactivate all TX queues before change the value and bring them back after we are done, this also makes implementation easier. Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by:
-
Cong Wang authored
This patch promotes the local change_tx_queue_len() to a core helper function, dev_change_tx_queue_len(), so that rtnetlink and net-sysfs could share the code. This also prepares for the following patch. Note, the -EFAULT in the original code doesn't make sense, we should propagate the errno from notifiers. Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by:
-
Jason Wang authored
We don't stop device before reset owner, this means we could try to serve any virtqueue kick before reset dev->worker. This will result a warn since the work was pending at llist during owner resetting. Fix this by stopping device during owner reset. Reported-by: syzbot+eb17c6162478cc50632c@syzkaller.appspotmail.com Fixes: 3a4d5c94 ("vhost_net: a kernel-level virtio server") Signed-off-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
David S. Miller authored
Nicolas Dichtel says: ==================== net: Ease to follow an interface that moves to another netns The goal of this series is to ease the user to follow an interface that moves to another netns. After this series, with a patched iproute2: $ ip netns bar foo $ ip monitor link & $ ip link set dummy0 netns foo Deleted 5: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default link/ether 6e:a7:82:35:96:46 brd ff:ff:ff:ff:ff:ff new-nsid 0 new-ifindex 6 => new nsid: 0, new ifindex: 6 (was 5 in the previous netns) $ ip link set eth1 netns bar Deleted 3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default link/ether 52:54:01:12:34:57 brd ff:ff:ff:ff:ff:ff new-nsid 1 new-ifindex 3 => new nsid: 1, new ifindex: 3 (same ifindex) $ ip netns bar (id: 1) foo (id: 0) ==================== Signed-off-by: -
Nicolas Dichtel authored
The goal is to let the user follow an interface that moves to another netns. CC: Jiri Benc <jbenc@redhat.com> CC: Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by:
Jiri Benc <jbenc@redhat.com> Signed-off-by:
-
Nicolas Dichtel authored
The user should be able to follow any interface that moves to another netns. There is no reason to hide physical interfaces. CC: Jiri Benc <jbenc@redhat.com> CC: Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by:
-
Vadim Lomovtsev authored
It was found that ethtool provides unexisting module name while it queries the specified network device for associated driver information. Then user tries to unload that module by provided module name and fails. This happens because ethtool reads value of DRV_NAME macro, while module name is defined at the driver's Makefile. This patch is to correct Cavium CN88xx Thunder NIC driver names (DRV_NAME macro) 'thunder-nicvf' to 'nicvf' and 'thunder-nic' to 'nicpf', sync bgx and xcv driver names accordingly to their module names. Signed-off-by:
Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com> Signed-off-by:
-
David S. Miller authored
Michael S. Tsirkin says: ==================== ptr_ring fixes This fixes a bunch of issues around ptr_ring use in net core. One of these: "tap: fix use-after-free" is also needed on net, but can't be backported cleanly. I will post a net patch separately. Lightly tested - Jason, could you pls confirm this addresses the security issue you saw with ptr_ring? Testing reports would be appreciated too. ==================== Signed-off-by:
-
Michael S. Tsirkin authored
Offset 128 overlaps the last word of the redzone. Use 132 which is always beyond that. Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Michael S. Tsirkin authored
This is to make ptr_ring test build again. Signed-off-by:
-
Michael S. Tsirkin authored
Signed-off-by:
-
Michael S. Tsirkin authored
We don't rely on lockless guarantees, but it seems cleaner than inverting __ptr_ring_peek. Signed-off-by:
-
Michael S. Tsirkin authored
In theory compiler could tear queue loads or stores in two. It does not seem to be happening in practice but it seems easier to convert the cases where this would be a problem to READ/WRITE_ONCE than worry about it. Signed-off-by:
-
Michael S. Tsirkin authored
__skb_array_empty should use __ptr_ring_empty since that's the only legal lockless function. Signed-off-by:
-
Michael S. Tsirkin authored
This reverts commit bcecb4bb. If we try to allocate an extra entry as the above commit did, and when the requested size is UINT_MAX, addition overflows causing zero size to be passed to kmalloc(). kmalloc then returns ZERO_SIZE_PTR with a subsequent crash. Reported-by: syzbot+87678bcf753b44c39b67@syzkaller.appspotmail.com Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by:
John Fastabend <john.fastabend@gmail.com> Signed-off-by:
-
