While receiving unsupported rate frame rx state machine
gets into a state 0xb and if phy_restart happens in that
state, BB would go hang. If RXSM is in 0xb state after
first bb panic, ensure to disable the phy_restart.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Resetting hardware helps to recover from baseband
hang/panic for AR9003 based chips.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reported-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Although a previous fix handles the kernel panics that result from
failure to allocate a new RX buffer, memory fragmentation can be
reduced if the amsdu_8k capability is disabled as new buffers need only
be of O(0), not O(2).
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

To handle amsdu_8k capability, the PCI routine of this driver must
allocate receive buffers of order 2. Under heavy load, this causes
fragmentation of memory. The present code releases the current buffer
before checking to see if a new one is availble. Recovery from
allocation failures is not possible, which results in kernel panics.

The fix is to reorder the code to check that a new buffer can be
allocated before the old one is released. If not possible, the
received frame is dropped and the old one is reused. Without this
change, it is impossible to transfer a 2 GB file without a kernel panic.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>              [2.6.{37,38,39}]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In both trigger_scan and sched_scan operations, we were checking for
the SSID length before assigning the value correctly.  Since the
memory was just kzalloc'ed, the check was always failing and SSID with
over 32 characters were allowed to go through.

This was causing a buffer overflow when copying the actual SSID to the
proper place.

This bug has been there since 2.6.29-rc4.

Cc: stable@kernel.org
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While decoding received event packet from firmware, 4 bytes
of interface header are already removed unconditionally.
So for handling event only 4 more bytes needs to be pulled.
This is achieved by changing event header length to 4.

Almost all the events, except BA stream related and AMSDU
aggregation control events, do not have the payload in their
event skb. Such events handling depends only on the event ID.
This event ID is the first four bytes of the event skb, which
is copied to a separate variable before pulling the skb header.
Hence event handling worked only for those events that didn't
have payload in event skb.

This patch fixes the broken event path of the events with
payload in their event skb without harming existing working
event path for the events without payload.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix new kernel-doc Error and Warning in <net/mac80211.h>:

Error(linux-2.6.39-git5/include/net/mac80211.h:550): cannot understand prototype: 'struct ieee80211_sched_scan_ies '
Warning(linux-2.6.39-git5/include/net/mac80211.h:2289): No description found for parameter 'sta'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix new kernel-doc warnings in <net/cfg80211.h>:

Warning(linux-2.6.39-git5/include/net/cfg80211.h:560): No description found for parameter 'bss_param'
Warning(linux-2.6.39-git5/include/net/cfg80211.h:1555): Enum value 'WIPHY_FLAG_SUPPORTS_SCHED_SCAN' not described in enum 'wiphy_flags'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix compiling error when CONFIG_MAC80211_DEBUGFS is not enabled
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:351: error: 'struct iwl_lq_sta' has no member named 'dbg_fixed_rate'
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:1076: error: 'struct iwl_lq_sta' has no member named 'dbg_fixed_rate'
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

otherwise we will get deadbeef when the station is in idle state
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some stack variables (name *ssid and *channel) are only used to define
the size of the memory block that needs to be allocated for the
request structure in the nl80211_trigger_scan() and
nl80211_start_sched_scan() functions.

This is unnecessary because the sizes of the actual elements in the
structure can be used instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After commit 1928ecab (mac80211: fix and
simplify mesh locking) mesh table allocation is performed with the
pathtbl_resize_lock taken.  Under those conditions one should not sleep.
This patch makes the allocations GFP_ATOMIC to prevent that.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We risk reading TMSHIGH register twice, but PHY-A are really rare and we
do not support them at the moment.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rounding up the delta between last-beacon-tsf and tsf to intval is wrong
and can lead to misconfigured timers which breaks beacon transmission.
Fix this by adding intval and subtracting the offset of the tsf within the
current slot.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The Times They Are a-Changin'.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The WMI tx status event timeout was not aligning with the
TX cleanup timer threshold value. Fix this to handle dropped
packets.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reduce the credit size for UB94/95 to fix target hangs.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit "ath9k_htc: Fix AMPDU subframe handling" registered the maximum
subframe limit of the driver with mac80211, which was used in ADDBA
negotiation. While technically correct, this causes inter-operability issues
with a few APs. Revert to the older behavior to fix this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The BSSID/AID has to be set for the first associated station interface.
Subsequent interfaces may move out of assoc/disassoc status, in which
case, the BSSID has to be re-calculated from the available interfaces.
Also, ANI should be enabled or disabled based on the current opmode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Choose the MY_BEACON filter only in case of a single interface.
Also, set the ATH9K_RX_FILTER_MCAST_BCAST_ALL filter in case
of interfaces.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The FW does absolutely nothing with the station flags,
so remove them. But keep the field around since it might
come in handy in the future.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove all the unsupported modes like FH, TURBO etc.
Since this requires a FW update, increase the fw version to 1.3
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cmd_index is never used.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is to fix an issue that the throughput of the higher priority
stream gets dropped when a lower priority stream is present.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If we go through the entire for loop in
mwifiex_wmm_get_highest_priolist_ptr() and don't find any packets,
set highest_queued_prio to NO_PKT_PRIO_TID (< LOW_PRIO_TID).
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

add checks to mwifiex_wmm_process_tx() loop so it doesn't re-enter
mwifiex_dequeue_tx_packet() to find it can't send.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds highest_queued_prio to track priority of packets as
they are enqueued so that mwifiex_wmm_get_highest_priolist_ptr()
starts checking at the first level where we have packets, instead of
the highest. The function also lowers priority value to the level
where first packet is found.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds tx_pkts_queued to track number of packets being
enqueued & dequeued so that mwifiex_wmm_lists_empty() evaluation
is lightweight.
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds a new generic gpio rfkill driver to support rfkill switches
which are controlled by gpios. The driver also supports passing in
data about the clock for the radio, so that when rfkill is blocking,
it can disable the clock.

This driver assumes platform data is passed from the board files to
configure it for specific devices.
Original-patch-by: Anantha Idapalapati <aidapalapati@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In ad-hoc mode, beacon timers are configured differently compared to AP
mode, and (depending on the scenario) can vary enough to make the beacon
tasklet not detect slot 0 based on the TSF.
Since staggered beacons are not (and cannot be) used in ad-hoc mode, it
makes more sense to just hardcode slot 0 here, avoiding unnecessary
TSF reads and calculations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211 scan code adds separate BSS entries if the same BSS shows up
on multiple channels. However, sme implementation does not use the
frequency when fetching the BSS entry. Fix this by adding channel
information to cfg80211_roamed() and include it in cfg80211_get_bss()
calls.

Please note that drivers using cfg80211_roamed() need to be modified to
fully implement this fix. This commit includes only minimal changes to
avoid compilation issues; it maintains the old (broken) behavior for
most drivers. ath6kl was the only one that I could test, so I updated
it to provide the operating frequency in the roamed event.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>