- 29 Jul, 2015 6 commits
-
-
Satish Ashok authored
When fast leave is configured on a bridge port and an IGMP leave is received for a group, the group is not deleted immediately if there is a router detected or if multicast querier is configured. Ideally the group should be deleted immediately when fast leave is configured. Signed-off-by:
Satish Ashok <sashok@cumulusnetworks.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Toshiaki Makita authored
There are several devices that can receive vlan tagged packets with CHECKSUM_PARTIAL like tap, possibly veth and xennet. When (multiple) vlan tagged packets with CHECKSUM_PARTIAL are forwarded by bridge to a device with the IP_CSUM feature, they end up with checksum error because before entering bridge, the network header is set to ETH_HLEN (not including vlan header length) in __netif_receive_skb_core(), get_rps_cpu(), or drivers' rx functions, and nobody fixes the pointer later. Since the network header is exepected to be ETH_HLEN in flow-dissection and hash-calculation in RPS in rx path, and since the header pointer fix is needed only in tx path, set the appropriate network header on forwarding packets. Signed-off-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by:
-
Alexander Drozdov authored
tpacket_fill_skb() can return a negative value (-errno) which is stored in tp_len variable. In that case the following condition will be (but shouldn't be) true: tp_len > dev->mtu + dev->hard_header_len as dev->mtu and dev->hard_header_len are both unsigned. That may lead to just returning an incorrect EMSGSIZE errno to the user. Fixes: 52f1454f ("packet: allow to transmit +4 byte in TX_RING slot for VLAN case") Signed-off-by:
Alexander Drozdov <al.drozdov@gmail.com> Acked-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Eric Dumazet authored
When arp is off on a device, and ioctl(SIOCGARP) is queried, a buggy answer is given with MAC address of the device, instead of the mac address of the destination/gateway. We filter out NUD_NOARP neighbours for /proc/net/arp, we must do the same for SIOCGARP ioctl. Tested: lpaa23:~# ./arp 10.246.7.190 MAC=00:01:e8:22:cb:1d // correct answer lpaa23:~# ip link set dev eth0 arp off lpaa23:~# cat /proc/net/arp # check arp table is now 'empty' IP address HW type Flags HW address Mask Device lpaa23:~# ./arp 10.246.7.190 MAC=00:1a:11:c3:0d:7f // buggy answer before patch (this is eth0 mac) After patch : lpaa23:~# ip link set dev eth0 arp off lpaa23:~# ./arp 10.246.7.190 ioctl(SIOCGARP) failed: No such device or address Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
Vytautas Valancius <valas@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by:
-
David Ward authored
This notification causes the FIB to be updated, which is not needed because the address already exists, and more importantly it may undo intentional changes that were made to the FIB after the address was originally added. (As a point of comparison, when an address becomes deprecated because its preferred lifetime expired, a notification on this chain is not generated.) The motivation for this commit is fixing an incompatibility between DHCP clients which set and update the address lifetime according to the lease, and a commercial VPN client which replaces kernel routes in a way that outbound traffic is sent only through the tunnel (and disconnects if any further route changes are detected via netlink). Signed-off-by:
David Ward <david.ward@ll.mit.edu> Signed-off-by:
-
Nikolay Aleksandrov authored
These should be handled only by the respective STP which is in control. They become problematic for devices with limited resources with many ports because the hold_timer is per port and fires each second and the hello timer fires each 2 seconds even though it's global. While in user-space STP mode these timers are completely unnecessary so it's better to keep them off. Also ensure that when the bridge is up these timers are started only when running with kernel STP. Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
- 27 Jul, 2015 27 commits
-
-
Lars Westerhoff authored
When binding a PF_PACKET socket, the use count of the bound interface is always increased with dev_hold in dev_get_by_{index,name}. However, when rebound with the same protocol and device as in the previous bind the use count of the interface was not decreased. Ultimately, this caused the deletion of the interface to fail with the following message: unregister_netdevice: waiting for dummy0 to become free. Usage count = 1 This patch moves the dev_put out of the conditional part that was only executed when either the protocol or device changed on a bind. Fixes: 902fefb8 ('packet: improve socket create/bind latency in some cases') Signed-off-by:Lars Westerhoff <lars.westerhoff@newtec.eu> Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Daniel Borkmann <dborkman@redhat.com> Signed-off-by:
-
Ivan Vecera authored
Network header is set with offset ETH_HLEN but it is not true for VLAN (multiple-)tagged and results in checksum issues in lower devices. v2: leave skb->protocol untouched (thx Vlad), comment added v3: moved after skb_probe_transport_header() call (thx Toshiaki) Signed-off-by:
Ivan Vecera <ivecera@redhat.com> Signed-off-by:
-
Alexander Duyck authored
It was reported that update_suffix was taking a long time on systems where a large number of leaves were attached to a single node. As it turns out fib_table_flush was calling update_suffix for each leaf that didn't have all of the aliases stripped from it. As a result, on this large node removing one leaf would result in us calling update_suffix for every other leaf on the node. The fix is to just remove the calls to leaf_pull_suffix since they are redundant as we already have a call in resize that will go through and update the suffix length for the node before we exit out of fib_table_flush or fib_table_flush_external. Reported-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
Alexander Duyck <alexander.h.duyck@redhat.com> Tested-by:
-
David S. Miller authored
If an architecture defines readl/writel using CPP macros, we get the following kinds of build failure: > > > drivers/net/ethernet/cadence/macb.c:164:1: error: macro "writel" > > > passed 3 arguments, but takes just 2 > macb_or_gem_writel(bp, SA1B, bottom); > ^ Rename the methods so that this doesn't happen. Signed-off-by: -
Andrew Lunn authored
When a switch is attached to the mdio bus, the mdio bus can be used while the interface is not open. If the IPG clock is not enabled, MDIO reads/writes will simply time out. Add support for runtime PM to control this clock. Enable/disable this clock using runtime PM, with open()/close() and mdio read()/write() function triggering runtime PM operations. Since PM is optional, the IPG clock is enabled at probe and is no longer modified by fec_enet_clk_enable(), thus if PM is not enabled in the kernel, it is guaranteed the clock is running when MDIO operations are performed. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Cc: tyler.baker@linaro.org Cc: fabio.estevam@freescale.com Cc: shawn.guo@linaro.org Tested-by:
Fabio Estevam <fabio.estevam@freescale.com> Tested-by:
Tyler Baker <tyler.baker@linaro.org> Signed-off-by:
-
WingMan Kwok authored
This patch asserts SGMII RTRESET, i.e. resetting the SGMII Tx/Rx logic, during network interface shutdown to avoid having the hardware wedge when shutting down with high incoming traffic rates. This is cleared (brought out of RTRESET) when the interface is brought back up. Signed-off-by:
WingMan Kwok <w-kwok2@ti.com> Signed-off-by:
-
David S. Miller authored
Andy Shevchenko says: ==================== net/macb: fix for AVR32 and clean up It seems no one had tested recently the driver on AVR32 platforms such as ATNGW100. This series bring it back to work. ==================== Signed-off-by: -
Andy Shevchenko authored
This patch coverts struct description to the kernel doc format. There is no functional change. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Andy Shevchenko authored
macb_count_tx_descriptors() repeats the generic macro DIV_ROUND_UP(). The patch does a replacement. There is no functional change. Signed-off-by:
-
Andy Shevchenko authored
This patch fixes the following warnings: drivers/net/ethernet/cadence/macb.c: In function ‘macb_handle_link_change’: drivers/net/ethernet/cadence/macb.c:266: warning: comparison between signed and unsigned drivers/net/ethernet/cadence/macb.c:267: warning: comparison between signed and unsigned drivers/net/ethernet/cadence/macb.c:291: warning: comparison between signed and unsigned drivers/net/ethernet/cadence/macb.c: In function ‘gem_update_stats’: drivers/net/ethernet/cadence/macb.c:1908: warning: comparison between signed and unsigned drivers/net/ethernet/cadence/macb.c: In function ‘gem_get_ethtool_strings’: drivers/net/ethernet/cadence/macb.c:1988: warning: comparison between signed and unsigned Signed-off-by:
-
Andy Shevchenko authored
To avoid messages like macb macb.0 (unnamed net_device) (uninitialized): Cadence caps 0x00000000 macb macb.0 (unnamed net_device) (uninitialized): invalid hw address, using random let's use dev_*() macros. Signed-off-by:
-
Andy Shevchenko authored
The commit 98b5a0f4 introduces jumbo frame support, but also it assumes that macb_config present which is not always true. The configuration without macb_config fails to boot. Unable to handle kernel NULL pointer dereference at virtual address 00000010 ptbr = 90350000 pgd = 00000000 Oops: Kernel access of bad area, sig: 11 [#1] FRAME_POINTER chip: 0x01f:0x1e82 rev 2 Modules linked in: CPU: 0 PID: 1 Comm: swapper Not tainted 4.2.0-rc3-next-20150723+ #13 task: 91c26000 ti: 91c28000 task.ti: 91c28000 PC is at macb_probe+0x140/0x61c Fixes: 98b5a0f4 (net: macb: Add support for jumbo frames) Signed-off-by:
-
Andy Shevchenko authored
The commit a50dad35 (net: macb: Add big endian CPU support) converted I/O accessors to readl_relaxed() and writel_relaxed() and consequentially broke MACB driver on AVR32 platforms such as ATNGW100. This patch improves I/O access by checking endiannes first and use the corresponding methods. Fixes: a50dad35 (net: macb: Add big endian CPU support) Signed-off-by:
-
Sabrina Dubroca authored
Currently, tcp_recvmsg enters a busy loop in sk_wait_data if called with flags = MSG_WAITALL | MSG_PEEK. sk_wait_data waits for sk_receive_queue not empty, but in this case, the receive queue is not empty, but does not contain any skb that we can use. Add a "last skb seen on receive queue" argument to sk_wait_data, so that it sleeps until the receive queue has new skbs. Link: https://bugzilla.kernel.org/show_bug.cgi?id=99461 Link: https://sourceware.org/bugzilla/show_bug.cgi?id=18493 Link: https://bugzilla.redhat.com/show_bug.cgi?id=1205258Reported-by:
Enrico Scholz <rh-bugzilla@ensc.de> Reported-by:
Dan Searle <dan@censornet.com> Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Acked-by:
-
David S. Miller authored
Hayes Wang says: ==================== r8152: issues fix v2: Replace patch #2 with "r8152: fix wakeup settings". v1: These patches are used to fix issues. ==================== Signed-off-by: -
hayeswang authored
Adjust napi_disable() and napi_enable() to avoid r8152_poll() start working before rx ready. Otherwise, it may have race condition for rx_agg. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
hayeswang authored
Avoid the driver to enable WOL if the device doesn't support it. Signed-off-by:
-
hayeswang authored
- Disable U1/U2 during initialization. - Disable lpm when linking is on, and enable it when linking is off. - Disable U1/U2 when enabling runtime suspend. It is possible to let hw stop working, if the U1/U2 request occurs during some situations. The patch is used to avoid it. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetoothDavid S. Miller authored
Johan Hedberg says: ==================== pull request: bluetooth 2015-07-23 Here's another one-patch pull request for 4.2 which targets a potential NULL pointer dereference in the LE Security Manager code that can be triggered by using older user space tools. The issue has been there since 4.0 so there's the appropriate "Cc: stable" in place. Let me know if there are any issues pulling. Thanks. ==================== Signed-off-by: -
Lucas Stach authored
This function frees resources and cancels delayed work item that have been initialized in fec_ptp_init(). Use this to do proper error handling if something goes wrong in probe function after fec_ptp_init has been called. Signed-off-by:
Fugang Duan <B38611@freescale.com> Signed-off-by:
-
Lucas Stach authored
So it gets freed when the device is going away. This fixes a DMA memory leak on driver probe() fail and driver remove(). Signed-off-by:
-
Jiri Pirko authored
Fixes: a3138df9 ("[NIU]: Add Sun Neptune ethernet driver.") Signed-off-by:
Jiri Pirko <jiri@resnulli.us> Signed-off-by:
-
David S. Miller authored
Florian Westphal says: ==================== inet: ip defrag bug fixes Johan Schuijt and Frank Schreuder reported crash and softlockup after the inet workqueue eviction change: general protection fault: 0000 [#1] SMP CPU: 0 PID: 4 Comm: kworker/0:0 Not tainted 3.18.18-transip-1.5 #1 Workqueue: events inet_frag_worker task: ffff880224935130 ti: ffff880224938000 task.ti: ffff880224938000 RIP: 0010:[<ffffffff8149288c>] [<ffffffff8149288c>] inet_evict_bucket+0xfc/0x160 RSP: 0018:ffff88022493bd58 EFLAGS: 00010286 RAX: ffff88021f4f3e80 RBX: dead000000100100 RCX: 000000000000006b RDX: 000000000000006c RSI: ffff88021f4f3e80 RDI: dead0000001000a8 RBP: 0000000000000002 R08: ffff880222273900 R09: ffff880036e49200 R10: ffff8800c6e86500 R11: ffff880036f45500 R12: ffffffff81a87100 R13: ffff88022493bd70 R14: 0000000000000000 R15: ffff8800c9b26280 [..] Call Trace: [<ffffffff814929e0>] ? inet_frag_worker+0x60/0x210 [<ffffffff8107e3a2>] ? process_one_work+0x142/0x3b0 [<ffffffff8107eb94>] ? worker_thread+0x114/0x440 [..] A second issue results in softlockup since the evictor may restart the eviction loop for a (potentially) unlimited number of times while local softirqs are disabled. Frank reports that test system remained stable for 14 hours of testing (before, crash occured within half an hour in their setup). ==================== Signed-off-by: -
Nikolay Aleksandrov authored
We can simply remove the INET_FRAG_EVICTED flag to avoid all the flags race conditions with the evictor and use a participation test for the evictor list, when we're at that point (after inet_frag_kill) in the timer there're 2 possible cases: 1. The evictor added the entry to its evictor list while the timer was waiting for the chainlock or 2. The timer unchained the entry and the evictor won't see it In both cases we should be able to see list_evictor correctly due to the sync on the chainlock. Joint work with Florian Westphal. Tested-by:
Frank Schreuder <fschreuder@transip.nl> Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
Florian Westphal authored
Frank reports 'NMI watchdog: BUG: soft lockup' errors when load is high. Instead of (potentially) unbounded restarts of the eviction process, just skip to the next entry. One caveat is that, when a netns is exiting, a timer may still be running by the time inet_evict_bucket returns. We use the frag memory accounting to wait for outstanding timers, so that when we free the percpu counter we can be sure no running timer will trip over it. Reported-and-tested-by:
-
Florian Westphal authored
Followup patch will call it after inet_frag_queue was freed, so q->net doesn't work anymore (but netf = q->net; free(q); mem_limit(netf) would). Tested-by:
-
Florian Westphal authored
commit 65ba1f1e ("inet: frags: fix a race between inet_evict_bucket and inet_frag_kill") describes the bug, but the fix doesn't work reliably. Problem is that ->flags member can be set on other cpu without chainlock being held by that task, i.e. the RMW-Cycle can clear INET_FRAG_EVICTED bit after we put the element on the evictor private list. We can crash when walking the 'private' evictor list since an element can be deleted from list underneath the evictor. Join work with Nikolay Alexandrov. Fixes: b13d3cbf ("inet: frag: move eviction of queues to work queue") Reported-by:
Johan Schuijt <johan@transip.nl> Tested-by:
-
- 26 Jul, 2015 7 commits
-
-
Daniel Borkmann authored
Back then when we added support for SCTP_SNDINFO/SCTP_RCVINFO from RFC6458 5.3.4/5.3.5, we decided to add a deprecation warning for the (as per RFC deprecated) SCTP_SNDRCV via commit bbbea41d ("net: sctp: deprecate rfc6458, 5.3.2. SCTP_SNDRCV support"), see [1]. Imho, it was not a good idea, and we should just revert that message for a couple of reasons: 1) It's uapi and therefore set in stone forever. 2) To be able to run on older and newer kernels, an SCTP application would need to probe for both, SCTP_SNDRCV, but also SCTP_SNDINFO/ SCTP_RCVINFO support, so that on older kernels, it can make use of SCTP_SNDRCV, and on newer kernels SCTP_SNDINFO/SCTP_RCVINFO. In my (limited) experience, a lot of SCTP appliances are migrating to newer kernels only ve(ee)ry slowly. 3) Some people don't have the chance to change their applications, f.e. due to proprietary legacy stuff. So, they'll hit this warning in fast path and are stuck with older kernels. But i.e. due to point 1) I really fail to see the benefit of a warning. So just revert that for now, the issue was reported up Jamal. [1] http://thread.gmane.org/gmane.linux.network/321960/Reported-by:
Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
-
David S. Miller authored
Or Gerlitz says: ==================== mlx4 driver fixes, July 22nd 2015 Just few mlx4 fixes.. the fix related to propagating port state changes to VF should go to -stable of >= 3.11, all the rest just to 4.2-rc ==================== Signed-off-by: -
Ido Shamay authored
In mlx4_en_is_ring_empty we check if ring surpassed its size. Since the prod and cons indicators are u32, there might be a state where prod wrapped around and cons, making this assert false, although no actual bug exists (other code segment can cope with this state). Signed-off-by:
Ido Shamay <idos@mellanox.com> Signed-off-by:
Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
Jack Morgenstein authored
When a port is not attached, the FW requires a longer than usual time to execute the SENSE_PORT command. In the command flow, the wait_for_completion_timeout call used in mlx4_cmd_wait puts the kernel thread into the uninterruptible state during this time. This, in turn, due to the computation method, causes the CPU load average to increase. Fix this by using wait_for_completion_interruptible_timeout() for the SENSE_PORT command, which puts the thread in the interruptible state. In this state, the thread does not contribute to the CPU load average. Treat the interrupted case as if the SENSE_PORT command returned port_type = NONE. Fix suggested by Gideon Naim <gideonn@mellanox.com> and Bart Van Assche <bart.vanassche@sandisk.com>. Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
-
Jack Morgenstein authored
The port-change event processing in procedure mlx4_eq_int() uses "slave" as the vf_oper array index. Since the value of "slave" is the PF function index, the result is that the PF link state is used for deciding to propagate the event for all the VFs. The VF link state should be used, so the VF function index should be used here. Fixes: 948e306d ('net/mlx4: Add VF link state support') Signed-off-by:
Matan Barak <matanb@mellanox.com> Signed-off-by:
-
Or Gerlitz authored
Some old PF drivers don't let VFs allocate counters, in that case, use the sink counter so the VF can load and operate properly. Fixes: 6de5f7f6 ('net/mlx4_core: Allocate default counter per port') Reported-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
-
Nikolay Aleksandrov authored
Since slave_changelink support was added there have been a few race conditions when using br_setport() since some of the port functions it uses require the bridge lock. It is very easy to trigger a lockup due to some internal spin_lock() usage without bh disabled, also it's possible to get the bridge into an inconsistent state. Signed-off-by:
-
