- 12 Jun, 2013 40 commits
-
-
Arend van Spriel authored
Added statistics for flow-control and packets dropped by the driver. Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Hante Meuleman authored
Currently firmware requested credits do not require fifo credits. From a buffer management point of view this is incorrect. So firwmware requested credits require also fifo credits before the packet can be transferred to the host. Reviewed-by:
-
Stanislaw Gruszka authored
This reverts commit dd9c4640. With "iwl{4965,3495): workaround for firmware frame tx rejection" patches we can enable IEEE80211_HW_REPORTS_TX_ACK_STATUS again. Tested-by:
Jake Edge <jake@lwn.net> Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Stanislaw Gruszka authored
Firmware can reject to transmit frame on passive channel, when it did not yet received any frame with valid CRC on that channel. Workaround this problem in the driver. Signed-off-by:
-
Stanislaw Gruszka authored
Firmware can reject to transmit frame on passive channel, when it did not yet received any frame with valid CRC on that channel. Workaround this problem in the driver. Tested-by:
-
Stanislaw Gruszka authored
Add functions that will stop/wake all queues. Make them safe regarding multiple calls and when some ac are stopped/woke independently. Tested-by:
-
Stanislaw Gruszka authored
Tested-by:
-
Thomas Huehn authored
This patch enabels ath5k to use the new rate table to lookup each mrr rate and retry information per packet. Signed-off-by:
Benjamin Vahl <bvahl@net.t-labs.tu-berlin.de> Signed-off-by:
Thomas Huehn <thomas@net.t-labs.tu-berlin.de> Signed-off-by:
-
Sujith Manoharan authored
ah->noise is maintained globally and not per-channel. This is updated in the reset() routine after the NF history has been filled for the *current channel*, just before switching to the new channel. There is no need to do it inside getnf(), since ah->noise must contain a value for the new channel. Cc: stable@vger.kernel.org Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Sujith Manoharan authored
The commits, "ath9k: Fix regression in channelwidth switch at the same channel" "ath9k: Fix invalid noisefloor reading due to channel update" attempted to fix noisefloor calibration when a channel switch happens due to HT20/HT40 bandwidth change. This is causing invalid readings resulting in messages like: "ath: phy16: NF[0] (-45) > MAX (-95), correcting to MAX". This results in an incorrect noise being used initially for reporting the signal level of received packets, until NF calibration is done and the history buffer is updated via the ANI timer, which happens much later. When a bandwidth change happens, it is appropriate to reset the internal history data for the channel. Do this correctly in the reset() routine by checking the "chanmode" variable. Cc: stable@vger.kernel.org Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by:
-
Sujith Manoharan authored
For AR9485 boards with XLNA, the default gpio config is not set correctly, fix this. Cc: stable@vger.kernel.org Signed-off-by:
-
Hauke Mehrtens authored
N-PHY and HT-PHY support is more or less stable and should be activated by default. Signed-off-by:
Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by:
-
Hauke Mehrtens authored
Most users are using bcma with a PCIe card, activate support for this by default. Signed-off-by:
-
Hauke Mehrtens authored
When b43 gets build into the kernel and it should use bcma we have to ensure that bcma was also build into the kernel and not as a module. In this patch this is also done for SSB, although you can not build b43 without ssb support for now. This fixes a build problem reported by Randy Dunlap in 5187EB95.2060605@infradead.org Reported-By:
Randy Dunlap <rdunlap@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Oleksij Rempel authored
All known ar7010+ar* device and current FW support STBC TX. This patch make use of it and suggest to send STBC if peer support it. I use wort "suggest" since currenly we have separate rate controller in FW which will make decision based on rate and hardware. Signed-off-by:
Oleksij Rempel <linux@rempel-privat.de> Signed-off-by:
-
Kirshenbaum Erez authored
WMI PCP Start flow should not be handled through: net_device_ops->ndo_open()->wil_up()->__wil_up() because it missing mandatory FW parameters (SSID,Channel,IEs, Security...). Prior to AP starting __wil_up() may be called with iftype set cfg80211_ops->change_virtual_intf(NL80211_IFTYPE_AP or STATION) depend on the application hostapd/wpa_supplicant/iw. there should not be an attempt to start an AP flow, AP/PCP start flow will be started latter by cfg80211_ops->start_ap(). Signed-off-by:
Kirshenbaum Erez <erezk@wilocity.com> Signed-off-by:
Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by:
-
Hauke Mehrtens authored
Tracing in wil6210 is activated with WIL6210_TRACING and not with ATH6KL_TRACING, this is used for the ath6kl driver. Rename the config option. Signed-off-by:
-
Vladimir Kondratiev authored
at the vring initialisation, memory pool get allocated in the FW. Make it 1-st because FW need this memory pool to precess next commands Signed-off-by:
-
Vladimir Kondratiev authored
No more need for special processing of EAPOL, FW can now send EAPOL frames using normal Tx queue for TID 0 This fixes "schedule while atomic" bug - start_xmit called in softirq context; while WMI mechanism that was used may sleep. Signed-off-by:
-
Vladimir Kondratiev authored
When starting secure AP, in some cases wpa_s provides probe template but not probe/assoc IE's. In this case, derive missing IE's from probe. Signed-off-by:
-
Vladimir Kondratiev authored
Report FC from the frame itself, as auxiliary information includes only frame subtype. This is preparation for future changes, when DMG beacon (extension frame) may be reported through wmi_evt_rx_mgmt() Signed-off-by:
-
Vladimir Kondratiev authored
map card's back-door debug data Signed-off-by:
-
Vladimir Kondratiev authored
It may take up to 3500ms for the FW to start AP/PCP. Increase accordingly, adding some safety margin. Signed-off-by:
-
Felix Fietkau authored
The CAB (Content after Beacon) queue is used for beacon-triggered transmission of buffered multicast frames. If lots of multicast frames were buffered and this queue fills up, it drowns out all regular traffic. To limit the damage that buffered traffic can do, try to limit the queued data to becaon_interval / 8. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Felix Fietkau authored
This adds support for PS-Poll and U-APSD driver-buffered frames (part of an aggregation session). Signed-off-by:
-
Felix Fietkau authored
Use the UAPSD hardware queue to get PS-Poll responses out as fast as possible and without backoff. Signed-off-by:
-
Arend van Spriel authored
When initialization within brcmf_bus_start() fails on steps before the brcmf_net_attach() the net_device for the primary interface needs to be freed. This patch resolves a panic during kernel boot as reported by Stephen Warren. ref.: http://mid.gmane.org/51AD1F22.2080004@wwwdotorg.orgTested-by:
Stephen Warren <swarren@nvidia.com> Reviewed-by:
-
Arend van Spriel authored
When data is available and fw signalling is enabled then TIM information should be sent to firmware. If it can piggy back on existing packet then do that otherwise create dummy packet to get information out. Cc: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
-
Arend van Spriel authored
In brcmf_net_attach() the hard_header_len is set to sum of ETH_HLEN and the headroom needed by the bus interface. Better use increment instead as hard_header_len is already initialized upon alloc_netdev(). Reviewed-by:
-
Arend van Spriel authored
The BDC header contains PropTx TLV signals that are useful to capture for debugging. This event captures the header and tlv's in binary form. This can be post-processed using trace-cmd plugin. Reviewed-by:
Franky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
The statistic counter send_pkts was wrongly counted conditionally. Correcting the mistake. Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
Currently suppressed packets get enque-ed with header which then gets pulled before transmit. It is more logical and clean to pull the header on return and push it unconditionally on xmit. Reviewed-by:
-
Hante Meuleman authored
During P2P testing it turned out that the firmware sents multiple multiple creditmap event messages. Only the first message from the firmware should be processed. Otherwise the firmware-signalled flow control can run haywire when it has packets outstanding in firmware. Reviewed-by:
-
Hante Meuleman authored
The destination entries for firmware-signalled flow control have the interface id stored. This needs to be translated to bsscfg index when looking up the ifp object for the interface. Reviewed-by:
-
Hante Meuleman authored
In case of TDLS find the correct MAC descriptor for fw signalling data. In case of TDLS each destination gets its own entry. This was not handled correctly for P2P client. Reviewed-by:
-
Hante Meuleman authored
When credit borrowing is active the BE credits have been depleted, however the worker should still be scheduled. In case of credit borrowing correct credit map to make sure worker remains active. Reviewed-by:
-
Hante Meuleman authored
Store gen bit on suppressed packet per entry and use latest stored version for each packet which gets transmitted to fw. Reviewed-by:
-
Hante Meuleman authored
Currently on a bus flow control both fws is informed and netif queue gets closed. In case of fw signalling enabled, let the flow control be handled by fw signalling only. Reviewed-by:
-
