- 03 Jul, 2018 13 commits
-
-
Jerome Brunet authored
Add support for the es7154 which is basically an es7134 with an embedded power amplifier and lower maximum sample rate Signed-off-by:
Jerome Brunet <jbrunet@baylibre.com> Signed-off-by:
Mark Brown <broonie@kernel.org>
-
Jerome Brunet authored
Drop AVDD in favor of PVDD to match the names used in the datasheet and only claim PVDD on the es7154. The es7134 and es7144 don't have a separate supply for the digital I/O. Signed-off-by:
-
Jerome Brunet authored
Update the documentation to add support for the es7154 and optional power supplies phandles. Signed-off-by:
-
Daniel Kurtz authored
Now that the I2S channel names are fixed, and DMA data flow order is consistent (ch1 then ch2), we can simplify channel start order: start the upstream channel and then the downstream channel for both playback and capture cases. Signed-off-by:
Daniel Kurtz <djkurtz@chromium.org> Signed-off-by:
-
Daniel Kurtz authored
The pointer() callback gets its value by reading the I2S BYTE_COUNT register. This is a 64-bit runnning transaction counter. If a transaction was aborted in the middle of a sample buffer, the counter will stop counting on a number divisible by the buffer size. Since we actually use it as a pointer into an aligned buffer, however, we do want to ensure that it always starts at a number divisible by the buffer size when starting a transaction, hence we reset it whenever starting a transaction. To accomplish this, it wasn't necessary to zero bytescount at the termination of each transaction, so remove this unnecessary code. Signed-off-by:
-
Daniel Kurtz authored
On capture, audio data is first copied from I2S to ACP memory, and then from ACP to SYSRAM. The I2S_TO_ACP_DMA interrupt fires on every sample transferred from I2S to ACP memory. That is it fires ~48000 times per second when capturing @ 48 kHz. Since we don't do anything on this interrupt anyway, disable it to save quite a few unnecessary interrupts. The real "work" (calling snd_pcm_period_elapsed()) is done when transfer from ACP to SYSRAM is complete. Signed-off-by:
-
Daniel Kurtz authored
On capture, audio data is first copied from I2S to ACP memory, and then to SYSRAM. For each step the channel number increases, so the names in the driver were wrong. Signed-off-by:
-
Daniel Kurtz authored
It is always correct to subtract out the starting bytescount value. Even in the case of 2^64 byte rollover (292 Million Years in the future @ 48000 Hz) the math still works out. Signed-off-by:
-
Daniel Kurtz authored
Commit 6b116dfb ("ASoC: AMD: make channel 1 dma as circular") made both channels circular, so this comment and logic no longer applies. Always stop ch2 (the channel closest to the output) before ch1. This ensures that the downstream circular DMA channel does not continue to play/capture repeated samples after the upstream circular DMA channel has already stopped. Signed-off-by:
-
Gustavo A. R. Silva authored
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
Jerome Brunet authored
Add support for the everest es7241 which is a simple 2 channels analog to digital converter. Signed-off-by:
-
Jerome Brunet authored
Signed-off-by:
-
Bard Liao authored
We are currently using power saving mode for button detection. However, it will impact the headset recording performance. This patch will switch button detection to normal mode in capture and switch to power saving mode in the end of capture. Signed-off-by:
Bard Liao <bardliao@realtek.com> Signed-off-by:
-
- 02 Jul, 2018 25 commits
-
-
Jerome Brunet authored
Add the VDD and AVDD power supplies to the DAPM graph as some board may need to enable a regulator to turn them on. Signed-off-by:
-
Jerome Brunet authored
For each supported sample rate, the es7134 can work with several mclk / sample rate ratio. Check if ratio we get is actually OK. Signed-off-by:
-
Jerome Brunet authored
64Khz is actually not supported by the es7134 according to the datasheet Fixes: 9000b59d ("ASoC: es7134: add es7134 DAC driver") Signed-off-by:
-
Daniel Mack authored
The .set_pll() and .set_clkdiv() callbacks are considered legacy and should not be used anymore. In order to support PXA boards on DT platforms, remove them and let the code figure out the correct dividers and PLL base frequencies itself. Signed-off-by:
Daniel Mack <daniel@zonque.org> Signed-off-by:
-
Daniel Mack authored
Commit d767d3ce ("ASoC: pxa: provide PCM ops for ssp, i2s and ac97 components") created a build-time dependency to SND_PXA2XX_LIB but missed to reflect that in Kconfig. Reported-by:
kbuild test robot <lkp@intel.com> Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
- 29 Jun, 2018 2 commits
-
-
KaiChieh Chuang authored
Signed-off-by:
KaiChieh Chuang <kaichieh.chuang@mediatek.com> Signed-off-by:
-
KaiChieh Chuang authored
use list_head for sub_dais, since original sub_dais array is sparsely occupied Signed-off-by:
-
