- 14 Mar, 2011 9 commits
-
-
Prabhakar Kushwaha authored
RX_WATER_MARK sets the number of locations in Rx FIFO that can be used before the transport layer instructs the link layer to transmit HOLDS. Note that it can take some time for the HOLDs to get to the other end, and that in the interim there must be enough room in the FIFO to absorb all data that could arrive. Update the new recommended value to 16. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
-
Prabhakar Kushwaha authored
When a single device error is detected, the device under the error is indicated by the error bit set in the DER. There is a one to one mapping between register bit and devices on Port multiplier(PMP) i.e. bit 0 represents PMP device 0 and bit 1 represents PMP device 1 etc. Current implementation treats Device error register value as device number not set of bits representing multiple device on PMP. It is changed to consider bit level. No need to check for each set bit as all command is going to be aborted. Signed-off-by: Ashish Kalra <B00888@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
-
Hannes Reinecke authored
As per SAT-3 the WWN ID should be included in the VPD page 0x83 (device identification) emulation. Signed-off-by: Hannes Reinecke <hare@suse.de> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
-
Viresh Kumar authored
Some DMA controllers (eg: drivers/dma/dw_dmac*) allow platform specific configuration for dma transfers. User drivers need to set chan->private field of channel with pointer to configuration data. This patch takes dma_priv data from platform data and passes it to chan->private_data, in order to pass platform specific configuration to DMAC controller. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
-
Joe Perches authored
Commit 40d69ba0 ("pata_hpt{37x|3x2n}: use pr_*(DRV_NAME ...) instead of printk(KERN_* ...)") used pr_<level>. Add #define pr_fmt and remove DRV_NAME. Increment driver version numbers. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
-
Jeff Garzik authored
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Viresh Kumar authored
The Arasan CompactFlash Device Controller has three basic modes of operation: PC card ATA using I/O mode, PC card ATA using memory mode, PC card ATA using true IDE modes. Currently driver supports only True IDE mode. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
-
Viresh Kumar authored
This patch adds ata_sff_queue_work() & ata_sff_queue_delayed_work() routine in libata-sff.c file. This routine can be used by ata drivers to use ata_sff_wq. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
-
Seth Heasley authored
This patch adds an updated SATA RAID DeviceID for the Intel Patsburg PCH. Signed-off-by: Seth Heasley <seth.heasley@intel.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
-
- 02 Mar, 2011 18 commits
-
-
Per Jessen authored
Recognize Marvell 88SE9125 PCIe SATA 6.0 Gb/s controller. Signed-off-by: Per Jessen <per@computer.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Sergei Shtylyov authored
Commit 6b7ae954 (libata: reimplement link power management) removed the check of ATA_FLAG_LPM but neglected to remove the flag itself. Do it now... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Sergei Shtylyov authored
All checks of ATA_FLAG_NO_LEGACY have been removed by the commits c791c306 ([libata] minor PCI IDE probe fixes and cleanups) and f0d36efd (libata: update libata core layer to use devres), so I think it's time to finally get rid of this flag... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Sergei Shtylyov authored
Commit 0d5ff566 (libata: convert to iomap) removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself. Do it now, at last... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Sergei Shtylyov authored
These flags are marked as obsolete and the checks for them have been removed by commit 29444088 (libata-sff: kill unused ata_bus_reset()), so I think it's time to finally get rid of them... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Sergei Shtylyov authored
Commit 14bdef98 ([libata] convert drivers to use ata.h mode mask defines) didn't convert these two libata driver outside drivers/ata/... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Sergei Shtylyov authored
The driver makes use of the two options (CONFIG_SATA_DWC_[V]DEBUG) to enable the debug output but they both are absent in drivers/ata/Kconfig... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Sergei Shtylyov authored
The driver erroneously uses ata_get_cmd_descript() not only for printing out the ATA commands but also the protocol and DMA direction enums. Add functions for properly printing those out... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Sergei Shtylyov authored
The caller expects this function to return the DMA channel number on success, while it returns 0... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Sergei Shtylyov authored
Fix the following compilation errors/warnings: drivers/ata/sata_dwc_460ex.c:43:1: warning: "DRV_NAME" redefined In file included from drivers/ata/sata_dwc_460ex.c:38: drivers/ata/libata.h:31:1: warning: this is the location of the previous definition drivers/ata/sata_dwc_460ex.c:44:1: warning: "DRV_VERSION" redefined drivers/ata/libata.h:32:1: warning: this is the location of the previous definition drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_exec_command_by_tag': drivers/ata/sata_dwc_460ex.c:1356: warning: passing argument 1 of `ata_get_cmd_descript' makes integer from pointer without a cast drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_issue': drivers/ata/sata_dwc_460ex.c:1476: warning: `err' is used uninitialized in this function drivers/ata/sata_dwc_460ex.c:1465: note: `err' was declared here drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_issue': drivers/ata/sata_dwc_460ex.c:1493: warning: passing argument 1 of `ata_get_cmd_descript' makes integer from pointer without a cast drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_prep': drivers/ata/sata_dwc_460ex.c:1537: error: `tag' undeclared (first use in this function) drivers/ata/sata_dwc_460ex.c:1537: error: (Each undeclared identifier is reported only once drivers/ata/sata_dwc_460ex.c:1537: error: for each function it appears in.) NB: error only happens if DEBUG_NCQ macro is defined... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Sergei Shtylyov authored
Somehow the driver was committed with a bare number for the PIO mask, instead of ATA_PIO4... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Jeff Garzik authored
-
James Bottomley authored
The conversion is quite complex given that the libata new error handler has to be hooked into the current libsas timeout and error handling. The way this is done is to process all the failed commands via libsas first, but if they have no underlying sas task (and they're on a sata device) assume they are destined for the libata error handler and send them accordingly. Finally, activate the port recovery of the libata error handler for each port known to the host. This is somewhat suboptimal, since that port may not need recovering, but given the current architecture of the libata error handler, it's the only way; and the spurious activation is harmless. Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
James Bottomley authored
Right at the moment, the libata error handler is incredibly monolithic. This makes it impossible to use from composite drivers like libsas and ipr which have to handle error themselves in the first instance. The essence of the change is to split the monolithic error handler into two components: one which handles a queue of ata commands for processing and the other which handles the back end of readying a port. This allows the upper error handler fine grained control in calling libsas functions (and making sure they only get called for ATA commands whose lower errors have been fixed up). Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
James Bottomley authored
The SCSI host eh_cmd_q should be protected by the host lock (not the port lock). This probably doesn't matter that much at the moment, since we try to serialise the add and eh pieces, but it might matter in future for more convenient error handling. Plus this switches libata to the standard eh pattern where you lock, remove from the cmd queue to a local list and unlock and then operate on the local list. Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
James Bottomley authored
For historical reasons, libsas uses the scsi host lock as the ata port lock, and libata always uses the ata host. For the old eh, this was largely irrelevant since the two locks were never mixed inside the code. However, the new eh has a case where it nests acquisition of the host lock inside the port lock (this does look rather deadlock prone). Obviously this would be an instant deadlock if the port lock were the host lock, so switch the libsas paths to use the ata host lock as well. Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
James Bottomley authored
The function ata_sas_port_init() has always really done its own thing. However, as a precursor to moving to the libata new eh, it has to be properly using the standard libata scan paths. This means separating the current libata scan paths into pieces which can be shared with libsas and pieces which cant (really just the async call and the host scan). Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Tejun Heo authored
ata_eh_analyze_serror() suppresses hotplug notifications if LPM is being used because LPM generates spurious hotplug events. It compared whether link->lpm_policy was different from ATA_LPM_MAX_POWER to determine whether LPM is enabled; however, this is incorrect as for drivers which don't implement LPM, lpm_policy is always ATA_LPM_UNKNOWN. This disabled hotplug detection for all drivers which don't implement LPM. Fix it by comparing whether lpm_policy is greater than ATA_LPM_MAX_POWER. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: stable@kernel.org Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
- 01 Mar, 2011 10 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/stagingLinus Torvalds authored
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: hwmon: (adt7411) add MODULE_DEVICE_TABLE hwmon: (ad7414) add MODULE_DEVICE_TABLE
-
Randy Dunlap authored
Fix new kernel-doc warning in fs/block_dev.c: Warning(fs/block_dev.c:937): No description found for parameter 'kill_dirty' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Rafael J. Wysocki authored
Several ACPI drivers fail to build if CONFIG_NET is unset, because they refer to things depending on CONFIG_THERMAL that in turn depends on CONFIG_NET. However, CONFIG_THERMAL doesn't really need to depend on CONFIG_NET, because the only part of it requiring CONFIG_NET is the netlink interface in thermal_sys.c. Put the netlink interface in thermal_sys.c under #ifdef CONFIG_NET and remove the dependency of CONFIG_THERMAL on CONFIG_NET from drivers/thermal/Kconfig. Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Len Brown <lenb@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Luming Yu <luming.yu@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6Linus Torvalds authored
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: drm: fix unsigned vs signed comparison issue in modeset ctl ioctl. drm/nv50-nvc0: make sure vma is definitely unmapped when destroying bo
-
Linus Torvalds authored
Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 * 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: omap4: prcm: Fix the CPUx clockdomain offsets OMAP2+: clocksource: fix crash on boot when !CONFIG_OMAP_32K_TIMER OMAP2/3: clock: fix fint calculation for DPLL_FREQSEL OMAP2+: mailbox: fix lookups for multiple mailboxes OMAP2420: mailbox: fix IVA vs DSP IRQ numbering mach-omap2: smartreflex: world-writable debugfs voltage files mach-omap2: pm: world-writable debugfs timer files mach-omap2: mux: world-writable debugfs files
-
Linus Torvalds authored
Merge branches 'perf-fixes-for-linus', 'x86-fixes-for-linus' and 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: perf timechart: Fix max number of cpus perf timechart: Fix black idle boxes in the title perf hists: Print number of samples, not the period sum * 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86: Use u32 instead of long to set reset vector back to 0 * 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: clockevents: Prevent oneshot mode when broadcast device is periodic
-
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuseLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse: fuse: fix truncate after open fuse: fix hang of single threaded fuseblk filesystem
-
git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2Linus Torvalds authored
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: ocfs2: Check heartbeat mode for kernel stacks only Ocfs2/refcounttree: Fix a bug for refcounttree to writeback clusters in a right number. ocfs2: Fix estimate of necessary credits for mkdir
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: eukrea-tlv320: fix platform_name ASoC: correct pxa AC97 DAI names ALSA: hda - Add support for new IDT 92HD98 and 92HD99 codecs ALSA: HDA: Add ideapad quirk for two Dell machines ALSA: HDA: Add a new Conexant codec 506e (20590) ALSA: usb-audio: fix oops due to cleanup race when disconnecting ASoC: Hook wm_hubs micbiases up to CLK_SYS ASoC: Correct definition of WM8903_VMID_RES_5K ASoC: Fix WM8958 default microphone detection argument ordering ALSA: HDA: Fix mic initialization in VIA auto parser ALSA: fix one memory leak in sound jack
-
Ben Hutchings authored
Commit e2cda322 ("thp: add pmd mangling generic functions") replaced some macros in <asm-generic/pgtable.h> with inline functions. If the functions are to be defined (not all architectures need them) then struct vm_area_struct must be defined first. So include <linux/mm_types.h>. Fixes a build failure seen in Debian: CC [M] drivers/media/dvb/mantis/mantis_pci.o In file included from arch/arm/include/asm/pgtable.h:460, from drivers/media/dvb/mantis/mantis_pci.c:25: include/asm-generic/pgtable.h: In function 'ptep_test_and_clear_young': include/asm-generic/pgtable.h:29: error: dereferencing pointer to incomplete type Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
- 28 Feb, 2011 3 commits
-
-
Don Zickus authored
A customer of ours, complained that when setting the reset vector back to 0, it trashed other data and hung their box. They noticed when only 4 bytes were set to 0 instead of 8, everything worked correctly. Mathew pointed out: | | We're supposed to be resetting trampoline_phys_low and | trampoline_phys_high here, which are two 16-bit values. | Writing 64 bits is definitely going to overwrite space | that we're not supposed to be touching. | So limit the area modified to u32. Signed-off-by: Don Zickus <dzickus@redhat.com> Acked-by: Matthew Garrett <mjg@redhat.com> Cc: <stable@kernel.org> LKML-Reference: <1297139100-424-1-git-send-email-dzickus@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
-
Thomas Renninger authored
Currently numcpus is determined in pid_put_sample which is only called on sched_switch/sched_wakeup sample processing. On a machine with a lot cpus I often saw the last cpu missing. Check for (max) numcpus on every event happening and in the beginning. -> fixes the issue for me. Signed-off-by: Thomas Renninger <trenn@suse.de> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: lenb@kernel.org LKML-Reference: <1298842606-55712-6-git-send-email-trenn@suse.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
-
Thomas Renninger authored
This fix is needed for eye of gnome and firefox svg viewers. Only Inkscape can handle the broken case. Compare with the other svg_legenda_box declarations, looks like a typo slipped in at this place. Signed-off-by: Thomas Renninger <trenn@suse.de> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: lenb@kernel.org LKML-Reference: <1298842606-55712-5-git-send-email-trenn@suse.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
-