commit 5c9fc93b upstream.

When priv_sta == NULL, mi->prev_sample is dereferenced too early. Move
the assignment further down, after the rate_control_send_low call.
Reported-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a0ec570f upstream.

These two events were sent to the default network
namespace.

This caused AP mode in a non-default netns to not
work correctly. Mgmt tx status was multicasted to
a different (default) netns instead of the one the
AP was in.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4928bd2e upstream.

Currently ath9k_htc will reboot firmware only if interface was
ever started. Which lead to the problem in case where interface
was never started but module need to be reloaded.

This patch will partially fix bug "ath9k_htc: Target is unresponsive"
https://github.com/qca/open-ath9k-htc-firmware/issues/1

Reproduction case:
- plug adapter
- make sure nothing will touch it. Stop Networkmanager or blacklist mac address of this adapter.
- rmmod ath9k_htc; sleep 1; modprobe ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dc2a87f5 upstream.

Currently we configure harwdare and clock, only after
interface start. In this case, if we reload module or
reboot PC without configuring adapter, firmware will freeze.
There is no software way to reset adpter.

This patch add initial configuration and set it in
disabled state, to avoid this freeze. Behaviour of this patch
should be similar to: ifconfig wlan0 up; ifconfig wlan0 down.

Bug: https://github.com/qca/open-ath9k-htc-firmware/issues/1Tested-by: Bo Shi <cnshibo@gmail.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b6658ff8 upstream.

When a not fully started aggregation session is destroyed
and flushed, we get a warning, e.g.

  WARNING: at drivers/net/wireless/iwlwifi/pcie/tx.c:1142 iwl_trans_pcie_txq_disable+0x11c/0x160
  queue 16 not used
  Modules linked in: [...]
  Pid: 5135, comm: hostapd Tainted: G        W  O 3.5.0 #10
  Call Trace:
  wlan0: driver sets block=0 for sta 00:03:7f:10:44:d3
   [<ffffffff81036492>] warn_slowpath_common+0x72/0xa0
   [<ffffffff81036577>] warn_slowpath_fmt+0x47/0x50
   [<ffffffffa0368d6c>] iwl_trans_pcie_txq_disable+0x11c/0x160 [iwlwifi]
   [<ffffffffa03a2099>] iwl_mvm_sta_tx_agg_flush+0xe9/0x150 [iwlmvm]
   [<ffffffffa0396c43>] iwl_mvm_mac_ampdu_action+0xf3/0x1e0 [iwlmvm]
   [<ffffffffa0293ad3>] ___ieee80211_stop_tx_ba_session+0x193/0x920 [mac80211]
   [<ffffffffa0294ed8>] __ieee80211_stop_tx_ba_session+0x48/0x70 [mac80211]
   [<ffffffffa029159f>] ieee80211_sta_tear_down_BA_sessions+0x4f/0x80 [mac80211]
   [<ffffffffa028a686>] __sta_info_destroy+0x66/0x370 [mac80211]
   [<ffffffffa028abb4>] sta_info_destroy_addr_bss+0x44/0x70 [mac80211]
   [<ffffffffa02a3e26>] ieee80211_del_station+0x26/0x50 [mac80211]
   [<ffffffffa01e6395>] nl80211_del_station+0x85/0x200 [cfg80211]

when a station deauthenticated from us without fully setting
up the aggregation session.

Fix this by checking the aggregation state before removing
the hardware queue.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a1923f1d upstream.

This SKU was missing in the list of supported devices

https://bugzilla.kernel.org/show_bug.cgi?id=60577Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 48bc1307 upstream.

Due to a firmware bug, it crashes when the beacon interval
is smaller than 16. Avoid this by refusing the station state
change creating the AP station, causing mac80211 to abandon
the attempt to connect to the AP, and eventually wpa_s to
blacklist it.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fe04e837 upstream.

Increment index in each iteration. Without this increment we are
overriding the added SSIDs and we will send only the last SSId
and (n_ssids - 1) broadcast probes.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 93a42667 upstream.

We didn't release the Rx AMPDU ressources properly.
This bug led to firmware assert after 16 BA sessions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 683a0e4d upstream.

Silence compiler warnings on 64-bit systems introduced by commit
05cf0dec ("USB: mos7840: fix race in led handling") which uses the
usb-serial data pointer to temporarily store the device type during
probe but failed to add the required casts.

[gregkh - change uintptr_t to unsigned long]
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 05cf0dec upstream.

Fix race in LED handling introduced by commit 0eafe4de ("USB: serial:
mos7840: add support for MCS7810 devices") which reused the port control
urb for manipulating the LED without making sure that the urb is not
already in use. This could lead to the control urb being manipulated
while in flight.

Fix by adding a dedicated LED urb and ctrlrequest along with a LED-busy
flag to handle concurrency.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 40c24f28 upstream.

Fix race in device-type detection introduced by commit 0eafe4de ("USB:
serial: mos7840: add support for MCS7810 devices") which used a static
variable to hold the device type.

Move type detection to probe and use serial data to store the device
type.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d8a083cc upstream.

Fix race in mos7840_get_reg which unconditionally manipulated the
control urb (which may already be in use) by adding a control-urb busy
flag.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fc514460 upstream.

Allocate a descriptor for each period of a cyclic transfer, not just the first.
Also since the callback needs to be called for each finished period make sure to
initialize the callback and callback_param fields of each descriptor in a cyclic
transfer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 079a036f upstream.

Without this patch the driver waits ~1 ms for the UART to become idle. At
115200n8 this time is (theoretically) enough to transfer 11.5 characters
(= 115200 bits/s / (10 Bits/char) * 1ms). As the mxs-auart has a fifo size
of 16 characters the clock is gated too early. The problem is worse for
lower baud rates.

This only happens to really shut down the transmitter in the middle of a
transfer if /dev/ttyAPPx isn't opened in userspace (e.g. by a getty) but
was at least once (because the bootloader doesn't disable the transmitter).

So increase the timeout to 20 ms which should be enough for 9600n8, too.
Moreover skip gating the clock if the timeout is elapsed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d5a12ea7 upstream.

Platform drivers use "platform:" prefix in module alias.
Also use DRIVER_NAME in MODULE_ALIAS to make module autoloading work.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d970d7fe upstream.

The handler needs to ack the pending events before actually handling them.
Otherwise a new event might come in after it it considered non-pending or
handled and is acked then without being handled. So this event is only
noticed when the next interrupt happens.

Without this patch an i.MX28 based machine running an rt-patched kernel
regularly hangs during boot.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a8d30608 upstream.

the return value of SNDRV_COMPRESS_VERSION always return default -ENOTTY as the
return value was never updated for this call
assign return value from put_user()
Reported-by: Haynes <hgeorge@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 697aebab upstream.

A fixup for Apple Mac Mini was lost during the adaption to the generic
parser because the fallback for the generic ID 8384:7680 was dropped,
and it resulted in the silence output (and maybe other problems).

Unfortunately, just adding the missing subsystem ID wasn't enough, in
this case.  The subsystem ID of this machine is 0000:0100 (what Apple
thought...?), and since snd_hda_pick_fixup() doesn't take the vendor
id zero into account, the driver ignored this entry.  Now it's fixed
to regard the vendor id zero as a valid value.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5c52add1 upstream.

Without this patch, the values for ideality (register 0x4b) and ideality
selection mask (register 0x4c) are inverted.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dd5e6d6a upstream.

We can't use dev->mod_index for selecting the interrupt routing entry,
because it's not an index into interrupt routing table. It will be even
wrong on a machine with 2 CPUs (4 cores). But all needed information is
contained in the PAT entries for the serial ports. mod[0] contains the
iosapic address and mod_info has some indications for the interrupt
input (at least it looks like it). This patch implements the searching
for the right iosapic and uses this interrupt input information.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 50861f5a upstream.

The parisc architecture does not have a pte special bit. As a result,
special mappings are handled with the VM_PFNMAP and VM_MIXEDMAP flags.
VM_MIXEDMAP mappings may or may not have a "struct page" backing. When
pfn_valid() is false, there is no "struct page" backing. Otherwise, they
are treated as normal pages.

The FireGL driver uses the VM_MIXEDMAP without a backing "struct page".
This treatment caused a panic due to a TLB data miss in
update_mmu_cache. This appeared to be in the code generated for
page_address(). We were in fact using a very circular bit of code to
determine the physical address of the PFN in various cache routines.
This wasn't valid when there was no "struct page" backing.  The needed
address can in fact be determined simply from the PFN itself without
using the "struct page".

The attached patch updates update_mmu_cache(), flush_cache_mm(),
flush_cache_range() and flush_cache_page() to check pfn_valid() and to
directly compute the PFN physical and virtual addresses.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 06f0cce4 upstream.

Allow binding of user memory to the AGP GART on systems with HP
Quicksilver AGP bus. This resolves 'bind memory failed' error seen in
dmesg:

 [29.365973] [TTM] AGP Bind memory failed.
 …
 [29.367030] [drm] Forcing AGP to PCI mode

The system doesn't more fail to bind the memory, and hence not falling
back to the PCI mode (if other failures aren't detected).

This is just a simple write down from the following patches:
agp/amd-k7: Allow binding user memory to the AGP GART
agp/hp-agp: Allow binding user memory to the AGP GART
Signed-off-by: Alex Ivanov <gnidorah@p0n4ik.tk>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3be7db6a upstream.

When an associativity level change is found for one thread, the
siblings threads need to be updated as well.  This is done today
for PRRN in stage_topology_update() but is missing for VPHN in
update_cpu_associativity_changes_mask().  This patch will correctly
update all thread siblings during a topology change.

Without this patch a topology update can result in a CPU in
init_sched_groups_power() getting stuck indefinitely in a loop.

This loop is built in build_sched_groups(). As a result of the thread
moving to a node separate from its siblings the struct sched_group will
have its next pointer set to point to itself rather than the sched_group
struct of the next thread.  This happens because we have a domain without
the SD_OVERLAP flag, which is correct, and a topology that doesn't conform
with reality (threads on the same core assigned to different numa nodes).
When this list is traversed by init_sched_groups_power() it will reach
the thread's sched_group structure and loop indefinitely; the cpu will
be stuck at this point.

The bug was exposed when VPHN was enabled in commit b7abef04 (v3.9).
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit acfdd4b1 upstream.

a.out support on ARM requires that argc, argv and envp are passed in
r0-r2 respectively, which requires hacking load_aout_binary to
prevent argc being clobbered by the return code. Whilst mainline kernels
do set the registers up in start_thread, the aout loader has never
carried the hack in mainline.

Initialising the registers in this way actually goes against the libc
expectations for ELF binaries, where argc, argv and envp are passed on
the stack, with r0 being used to hold a pointer to an exit function for
cleaning up after the dynamic linker if required. If the pointer is
NULL, then it is ignored. When execing an ELF binary, Linux currently
zeroes r0, then sets it to argc and then finally clobbers it with the
return value of the execve syscall, so we actually end up with:

	r0 = 0
	stack[0] = argc
	r1 = stack[1] = argv
	r2 = stack[2] = envp

libc treats r1 and r2 as undefined. The clobbering of r0 by sys_execve
works for user-spawned threads, but when executing an ELF binary from a
kernel thread (via call_usermodehelper), the execve is performed on the
ret_from_fork path, which restores r0 from the saved pt_regs, resulting
in argc being presented to the C library. This has horrible consequences
when the application exits, since we have an exit function registered
using argc, resulting in a jump to hyperspace.

This patch solves the problem by removing the partial a.out support from
arch/arm/ altogether.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Ashish Sangwan <ashishsangwan2@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bdae73cd upstream.

As of commit b9d4d42a (ARM: Remove __ARCH_WANT_INTERRUPTS_ON_CTXSW on
pre-ARMv6 CPUs), the mm switching on VIVT processors is done in the
finish_arch_post_lock_switch() function to avoid whole cache flushing
with interrupts disabled. The need for deferred mm switch is stored as a
thread flag (TIF_SWITCH_MM). However, with preemption enabled, we can
have another thread switch before finish_arch_post_lock_switch(). If the
new thread has the same mm as the previous 'next' thread, the scheduler
will not call switch_mm() and the TIF_SWITCH_MM flag won't be set for
the new thread.

This patch moves the switch pending flag to the mm_context_t structure
since this is specific to the mm rather than thread.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bf3f0f33 upstream.

Commit ae8a8b95 ("ARM: 7691/1: mm: kill unused TLB_CAN_READ_FROM_L1_CACHE
and use ALT_SMP instead") added early function returns for page table
cache flushing operations on ARMv7 SMP CPUs.

Unfortunately, when targetting Thumb-2, these `mov pc, lr' sequences
assemble to 2 bytes which can lead to corruption of the instruction
stream after code patching.

This patch fixes the alternates to use wide (32-bit) instructions for
Thumb-2, therefore ensuring that the patching code works correctly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fe956a1d upstream.

slots-fan on G5 Xserve is always running at full speed with windfarm_rm31
driver, resulting in a very high acoustic noise level. It seems the fan
parameters are incorrect, and have been copied from the Drive Bay fan
(RPM, not present on rm31) of the legacy therm_pm72 driver. This patch
changes the parameters to match the Slots fan (PWM) of therm_pm72. With
the patch, slots-fan speed drops from 99% to 19% during normal use,
and slots-temp settle to ~42'C.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8c0cc8a5 upstream.

Olof reports that noMMU builds error out with:

arch/arm/kernel/signal.c: In function 'setup_return':
arch/arm/kernel/signal.c:413:25: error: 'mm_context_t' has no member named 'sigpage'

This shows one of the evilnesses of IS_ENABLED().  Get rid of it here
and replace it with #ifdef's - and as no noMMU platform can make use
of sigpage, depend on CONIFG_MMU not CONFIG_ARM_MPU.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e0d40756 upstream.

Unfortunately, I never committed the fix to a nasty oops which can
occur as a result of that commit:

------------[ cut here ]------------
kernel BUG at /home/olof/work/batch/include/linux/mm.h:414!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 490 Comm: killall5 Not tainted 3.11.0-rc3-00288-gabe03080 #53
task: e90acac0 ti: e9be8000 task.ti: e9be8000
PC is at special_mapping_fault+0xa4/0xc4
LR is at __do_fault+0x68/0x48c

This doesn't show up unless you do quite a bit of testing; a simple
boot test does not do this, so all my nightly tests were passing fine.

The reason for this is that install_special_mapping() expects the
page array to stick around, and as this was only inserting one page
which was stored on the kernel stack, that's why this was blowing up.
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a5463cd3 upstream.

If kuser helpers are not provided by the kernel, disable user access to
the vectors page.  With the kuser helpers gone, there is no reason for
this page to be visible to userspace.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 48be69a0 upstream.

Move the signal handlers into a VDSO page rather than keeping them in
the vectors page.  This allows us to place them randomly within this
page, and also map the page at a random location within userspace
further protecting these code fragments from ROP attacks.  The new
VDSO page is also poisoned in the same way as the vector page.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f6f91b0d upstream.

Provide a kernel configuration option to allow the kernel user helpers
to be removed from the vector page, thereby preventing their use with
ROP (return orientated programming) attacks.  This option is only
visible for CPU architectures which natively support all the operations
which kernel user helpers would normally provide, and must be enabled
with caution.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e39e3f3e upstream.

FIQ should no longer copy the FIQ code into the user visible vector
page.  Instead, it should use the hidden page.  This change makes
that happen.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b9b32bf7 upstream.

Use linker magic to create the vectors and vector stubs: we can tell the
linker to place them at an appropriate VMA, but keep the LMA within the
kernel.  This gets rid of some unnecessary symbol manipulation, and
have the linker calculate the relocations appropriately.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 19accfd3 upstream.

Move the machine vector stubs into the page above the vector page,
which we can prevent from being visible to userspace.  Also move
the reset stub, and place the swi vector at a location that the
'ldr' can get to it.

This hides pointers into the kernel which could give valuable
information to attackers, and reduces the number of exploitable
instructions at a fixed address.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5b43e7a3 upstream.

Poison the memory between each kuser helper.  This ensures that any
branch between the kuser helpers will be appropriately trapped.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f928d4f2 upstream.

Fill the empty regions of the vectors page with an exception generating
instruction.  This ensures that any inappropriate branch to the vector
page is appropriately trapped, rather than just encountering some code
to execute.  (The vectors page was filled with zero before, which
corresponds with the "andeq r0, r0, r0" instruction - a no-op.)

Acked-by Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d5c78673 upstream.

On one sytem that mtrr range is more then 44bits, in dmesg we have
[    0.000000] MTRR default type: write-back
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-DFFFF write-through
[    0.000000]   E0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 [000080000000-0000FFFFFFFF] mask 3FFF80000000 uncachable
[    0.000000]   1 [380000000000-38FFFFFFFFFF] mask 3F0000000000 uncachable
[    0.000000]   2 [000099000000-000099FFFFFF] mask 3FFFFF000000 write-through
[    0.000000]   3 [00009A000000-00009AFFFFFF] mask 3FFFFF000000 write-through
[    0.000000]   4 [381FFA000000-381FFBFFFFFF] mask 3FFFFE000000 write-through
[    0.000000]   5 [381FFC000000-381FFC0FFFFF] mask 3FFFFFF00000 write-through
[    0.000000]   6 [0000AD000000-0000ADFFFFFF] mask 3FFFFF000000 write-through
[    0.000000]   7 [0000BD000000-0000BDFFFFFF] mask 3FFFFF000000 write-through
[    0.000000]   8 disabled
[    0.000000]   9 disabled

but /proc/mtrr report wrong:
reg00: base=0x080000000 ( 2048MB), size= 2048MB, count=1: uncachable
reg01: base=0x80000000000 (8388608MB), size=1048576MB, count=1: uncachable
reg02: base=0x099000000 ( 2448MB), size=   16MB, count=1: write-through
reg03: base=0x09a000000 ( 2464MB), size=   16MB, count=1: write-through
reg04: base=0x81ffa000000 (8519584MB), size=   32MB, count=1: write-through
reg05: base=0x81ffc000000 (8519616MB), size=    1MB, count=1: write-through
reg06: base=0x0ad000000 ( 2768MB), size=   16MB, count=1: write-through
reg07: base=0x0bd000000 ( 3024MB), size=   16MB, count=1: write-through
reg08: base=0x09b000000 ( 2480MB), size=   16MB, count=1: write-combining

so bit 44 and bit 45 get cut off.

We have problems in arch/x86/kernel/cpu/mtrr/generic.c::generic_get_mtrr().
1. for base, we miss cast base_lo to 64bit before shifting.
Fix that by adding u64 casting.

2. for size, it only can handle 44 bits aka 32bits + page_shift
Fix that with 64bit mask instead of 32bit mask_lo, then range could be
more than 44bits.
At the same time, we need to update size_or_mask for old cpus that does
support cpuid 0x80000008 to get phys_addr. Need to set high 32bits
to all 1s, otherwise will not get correct size for them.

Also fix mtrr_add_page: it should check base and (base + size - 1)
instead of base and size, as base and size could be small but
base + size could bigger enough to be out of boundary. We can
use boot_cpu_data.x86_phys_bits directly to avoid size_or_mask.

So When are we going to have size more than 44bits? that is 16TiB.

after patch we have right ouput:
reg00: base=0x080000000 ( 2048MB), size= 2048MB, count=1: uncachable
reg01: base=0x380000000000 (58720256MB), size=1048576MB, count=1: uncachable
reg02: base=0x099000000 ( 2448MB), size=   16MB, count=1: write-through
reg03: base=0x09a000000 ( 2464MB), size=   16MB, count=1: write-through
reg04: base=0x381ffa000000 (58851232MB), size=   32MB, count=1: write-through
reg05: base=0x381ffc000000 (58851264MB), size=    1MB, count=1: write-through
reg06: base=0x0ad000000 ( 2768MB), size=   16MB, count=1: write-through
reg07: base=0x0bd000000 ( 3024MB), size=   16MB, count=1: write-through
reg08: base=0x09b000000 ( 2480MB), size=   16MB, count=1: write-combining

-v2: simply checking in mtrr_add_page according to hpa.

[ hpa: This probably wants to go into -stable only after having sat in
  mainline for a bit.  It is not a regression. ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1371162815-29931-1-git-send-email-yinghai@kernel.orgSigned-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>